Pull timer fixes from Thomas Gleixner:
 "Three fixlets from the timer departement:

   - Update the timekeeper before updating vsyscall and pvclock.  This
     fixes the kvm-clock regression reported by Chris and Paolo.

   - Use the proper irq work interface from NMI.  This fixes the
     regression reported by Catalin and Dave.

   - Clarify the compat_nanosleep error handling mechanism to avoid
     future confusion"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Update timekeeper before updating vsyscall and pvclock
  compat: nanosleep: Clarify error handling
  nohz: Restore NMI safe local irq work for local nohz kick

Pull kvm fixes from Paolo Bonzini:
 "A smattering of bug fixes across most architectures"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  powerpc/kvm/cma: Fix panic introduces by signed shift operation
  KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
  KVM: s390/mm: Fix storage key corruption during swapping
  arm/arm64: KVM: Complete WFI/WFE instructions
  ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
  KVM: s390/mm: try a cow on read only pages for key ops
  KVM: s390: Fix user triggerable bug in dead code

Pull ARM SoC fixes from Kevin Hilman:
 "Another round of fixes from arm-soc land, which are mostly DT fixes
  for:

   - OMAP: handful of DT fixes devices on newly supported hardware
   - davinci: fix 2nd EDMA channel
   - ux500: extend previous pinctrl fix to another board
   - at91: clock registration fixes, compatibility string precision

  And one more fix for event cleanup in drivers/bus/arm-ccn"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  bus: arm-ccn: Move event cleanup routine
  ARM: at91/dt: rm9200: fix usb clock definition
  ARM: at91: rm9200: fix clock registration
  ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
  ARM: dts: dra7-evm: Add vtt regulator support
  ARM: dts: dra7-evm: Fix spi1 mux documentation
  ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
  ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
  ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am4372: fix USB regs size
  ARM: dts: am437x-gp: switch i2c0 to 100KHz
  ARM: dts: dra7-evm: Fix 8th NAND partition's name
  ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
  ARM: ux500: disable msp2 node on Snowball
  ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
  ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock

Pull xfs fixes from Dave Chinner:
 "The fixes all address recently discovered data corruption issues.

  The original Direct IO issue was discovered by Chris Mason @ Facebook
  on a production workload which mixed buffered reads with direct reads
  and writes IO to the same file.  The fix for that exposed other issues
  with page invalidation (exposed by millions of fsx operations) failing
  due to dirty buffers beyond EOF.

  Finally, the collapse_range code could also cause problems due to
  racing writeback changing the extent map while it was being shifted
  around.  The commits for that problem are simple mitigation fixes that
  prevent the problem from occuring.  A more robust fix for 3.18 that
  addresses the underlying problem is currently being worked on by
  Brian.

  Summary of fixes:
   - a direct IO read/buffered read data corruption
   - the associated fallout from the DIO data corruption fix
   - collapse range bugs that are potential data corruption issues"

* tag 'xfs-for-linus-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
  xfs: trim eofblocks before collapse range
  xfs: xfs_file_collapse_range is delalloc challenged
  xfs: don't log inode unless extent shift makes extent modifications
  xfs: use ranged writeback and invalidation for direct IO
  xfs: don't zero partial page cache pages during O_DIRECT writes
  xfs: don't zero partial page cache pages during O_DIRECT writes
  xfs: don't dirty buffers beyond EOF

Pull mtd fixes from Brian Norris:
 "Two trivial MTD updates for 3.17-rc4:

   - a tiny comment tweak, to kill a bunch of DocBook warnings added
     during the merge window

   - a small fixup to the OTP routines' error handling"

* tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd:
  mtd: nand: fix DocBook warnings on nand_sdr_timings doc
  mtd: cfi_cmdset_0002: check return code for get_chip()

The update_walltime() code works on the shadow timekeeper to make the
seqcount protected region as short as possible. But that update to the
shadow timekeeper does not update all timekeeper fields because it's
sufficient to do that once before it becomes life. One of these fields
is tkr.base_mono. That stays stale in the shadow timekeeper unless an
operation happens which copies the real timekeeper to the shadow.

The update function is called after the update calls to vsyscall and
pvclock. While not correct, it did not cause any problems because none
of the invoked update functions used base_mono.

commit cbcf2dd3 (x86: kvm: Make kvm_get_time_and_clockread()
nanoseconds based) changed that in the kvm pvclock update function, so
the stale mono_base value got used and caused kvm-clock to malfunction.

Put the update where it belongs and fix the issue.
Reported-by: Chris J Arges <chris.j.arges@canonical.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1409050000570.3333@nanosSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

The error handling in compat_sys_nanosleep() is correct, but
completely non obvious. Document it and restrict it to the
-ERESTART_RESTARTBLOCK return value for clarity.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull i2c bugfixes from Wolfram Sang:
 "I2C driver bugfixes for the 3.17 release.  Details can be found in the
  commit messages, yet I think this is typical driver stuff"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Revert "i2c: rcar: remove spinlock"
  i2c: at91: add bound checking on SMBus block length bytes
  i2c: rk3x: fix bug that cause transfer fails in master receive mode
  i2c: at91: Fix a race condition during signal handling in at91_do_twi_xfer.
  i2c: mv64xxx: continue probe when clock-frequency is missing
  i2c: rcar: fix MNR interrupt handling

Merge "at91: fixes for 3.17 #1" from Nicols Ferre:

First AT91 fixes batch for 3.17:
- compatibility string precision
- clock registration and USB DT fix for at91rm9200

* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: rm9200: fix usb clock definition
  ARM: at91: rm9200: fix clock registration
  ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
Signed-off-by: Kevin Hilman <khilman@linaro.org>

The function cleaning up an initialized event
was called from the "event_del" handler, instead
of being used as the "destroy" callback. In case of
events group allocation this caused NULL pointer
dereference (as events are added and deleted
multiple times then). Fixed now.
Signed-off-by: Pawel Moll <mail@pawelmoll.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Pull m68k updates from Geert Uytterhoeven:
 "Wire up new syscalls getrandom and memfd_create"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Wire up memfd_create
  m68k: Wire up getrandom

The atmel,clk-divisors property is taking 4 divisors, if less are
provided, the clock registration will fail.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Actually register clocks from device tree when using the common clock
framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: add at91 to function name]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The at91sam9g20 SOC uses its own pllb implementation which is different
from the one inherited from at91sam9260 SOC.
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Dave Hansen reports a massive scalability regression in an uncontained
page fault benchmark with more than 30 concurrent threads, which he
bisected down to 05b84301 ("mm: memcontrol: use root_mem_cgroup
res_counter") and pin-pointed on res_counter spinlock contention.

That change relied on the per-cpu charge caches to mostly swallow the
res_counter costs, but it's apparent that the caches don't scale yet.

Revert memcg back to bypassing res_counters on the root level in order
to restore performance for uncontained workloads.
Reported-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch changes sync_filesystem() to be EXPORT_SYMBOL().

The reason this is needed is that starting with 3.15 kernel, due to
Theodore Ts'o's commit 02b9984d ("fs: push sync_filesystem() down to
the file system's remount_fs()"), all file systems that have dirty data
to be written out need to call sync_filesystem() from their
->remount_fs() method when remounting read-only.

As this is now a generically required function rather than an internal
only function it should be EXPORT_SYMBOL() so that all file systems can
call it.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull regulator documentation fixes from Mark Brown:
 "All the fixes people have found for the regulator API have been
  documentation fixes, avoiding warnings while building the kerneldoc,
  fixing some errors in one of the DT bindings documents and fixing some
  typos in the header"

* tag 'regulator-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: fix kernel-doc warnings in header files
  regulator: Proofread documentation
  regulator: tps65090: Fix tps65090 typos in example

Merge tag 'omap-fixes-against-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "omap fixes against v3.17-rc3" from Tony Lindgren:

Few fixes for omaps mostly for various devices to get them working
properly on the new am437x and dra7 hardware for several devices
such as I2C, NAND, DDR3 and USB. There's also a clock fix for omap3.

And also included are two minor cosmetic fixes that are not
stictly fixes for the new hardware support added recently to
downgrade a GPMC warning into a debug statement, and fix the
confusing comments for dra7-evm spi1 mux.

Note that these are all .dts changes except for a GPMC change.

* tag 'omap-fixes-against-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (255 commits)
  ARM: dts: dra7-evm: Add vtt regulator support
  ARM: dts: dra7-evm: Fix spi1 mux documentation
  ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
  ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
  ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am4372: fix USB regs size
  ARM: dts: am437x-gp: switch i2c0 to 100KHz
  ARM: dts: dra7-evm: Fix 8th NAND partition's name
  ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
  Linux 3.17-rc3
  ...
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Pull GPIO fixes from Linus Walleij:
 - some documentation sync
 - resource leak in the bt8xx driver
 - again fix the way varargs are used to handle the optional flags on
   the gpiod_* accessors.  Now hopefully nailed the entire problem.

* tag 'gpio-v3.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: move varargs hack outside #ifdef GPIOLIB
  gpio: bt8xx: fix release of managed resources
  Documentation: gpio: documentation for optional getters functions

Pull drm fixes from Dave Airlie:
 - i915 fixes: a few display regressions
 - vmwgfx: possible loop forever fix
 - nouveau: one userspace interface fix

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/core: don't leak oclass type bits to user
  drm/i915: Fix lock dropping in intel_tv_detect()
  drm/i915: handle G45/GM45 pulse detection connected state.
  drm/vmwgfx: Fix a potential infinite spin waiting for fifo idle
  drm/vmwgfx: Fix an incorrect OOM return value
  drm/i915: Remove bogus __init annotation from DMI callbacks
  drm/i915: don't warn if backlight unexpectedly enabled
  drm/i915: Move intel_ddi_set_vc_payload_alloc(false) to haswell_crtc_disable()
  drm/i915: fix plane/cursor handling when runtime suspended
  drm/i915: Ignore VBT backlight presence check on Acer C720 (4005U)

Merge remote-tracking branches 'regulator/fix/doc' and 'regulator/fix/tps65090' into regulator-linus

single fix for nouveau.

* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau/core: don't leak oclass type bits to user

Fixes not being able to init fence subsystem when multiple boards are
present.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Pull aio bugfixes from Ben LaHaise:
 "Two small fixes"

* git://git.kvack.org/~bcrl/aio-fixes:
  aio: block exit_aio() until all context requests are completed
  aio: add missing smp_rmb() in read_events_ring

It seems that exit_aio() also needs to wait for all iocbs to complete (like
io_destroy), but we missed the wait step in current implemention, so fix
it in the same way as we did in io_destroy.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org

The local nohz kick is currently used by perf which needs it to be
NMI-safe. Recent commit though (7d1311b9)
changed its implementation to fire the local kick using the remote kick
API. It was convenient to make the code more generic but the remote kick
isn't NMI-safe.

As a result:

	WARNING: CPU: 3 PID: 18062 at kernel/irq_work.c:72 irq_work_queue_on+0x11e/0x140()
	CPU: 3 PID: 18062 Comm: trinity-subchil Not tainted 3.16.0+ #34
	0000000000000009 00000000903774d1 ffff880244e06c00 ffffffff9a7f1e37
	0000000000000000 ffff880244e06c38 ffffffff9a0791dd ffff880244fce180
	0000000000000003 ffff880244e06d58 ffff880244e06ef8 0000000000000000
	Call Trace:
	<NMI>  [<ffffffff9a7f1e37>] dump_stack+0x4e/0x7a
	[<ffffffff9a0791dd>] warn_slowpath_common+0x7d/0xa0
	[<ffffffff9a07930a>] warn_slowpath_null+0x1a/0x20
	[<ffffffff9a17ca1e>] irq_work_queue_on+0x11e/0x140
	[<ffffffff9a10a2c7>] tick_nohz_full_kick_cpu+0x57/0x90
	[<ffffffff9a186cd5>] __perf_event_overflow+0x275/0x350
	[<ffffffff9a184f80>] ? perf_event_task_disable+0xa0/0xa0
	[<ffffffff9a01a4cf>] ? x86_perf_event_set_period+0xbf/0x150
	[<ffffffff9a187934>] perf_event_overflow+0x14/0x20
	[<ffffffff9a020386>] intel_pmu_handle_irq+0x206/0x410
	[<ffffffff9a0b54d3>] ? arch_vtime_task_switch+0x63/0x130
	[<ffffffff9a01937b>] perf_event_nmi_handler+0x2b/0x50
	[<ffffffff9a007b72>] nmi_handle+0xd2/0x390
	[<ffffffff9a007aa5>] ? nmi_handle+0x5/0x390
	[<ffffffff9a0d131b>] ? lock_release+0xab/0x330
	[<ffffffff9a008062>] default_do_nmi+0x72/0x1c0
	[<ffffffff9a0c925f>] ? cpuacct_account_field+0xcf/0x200
	[<ffffffff9a008268>] do_nmi+0xb8/0x100

Lets fix this by restoring the use of local irq work for the nohz local
kick.
Reported-by: Catalin Iacob <iacobcatalin@gmail.com>
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>

Merge tag 'davinci-fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes

This patch fixes setup of second EDMA channel controller
on DA850.

* tag 'davinci-fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC

DRA7 evm REV G and later boards uses a vtt regulator for DDR3
termination and this is controlled by gpio7_11. This gpio is
configured in boot loader. gpio7_11, which is only available only on
Pad A22, in previous boards, is connected only to an unused pad on
expansion connector EXP_P3 and is safe to be muxed as GPIO on all
DRA7-evm versions (without a need to spin off another dts file).

Since gpio7_11 is used to control VTT and should not be reset or kept
in idle state during boot up else VTT will be disconnected and DDR
gets corrupted. So, as part of this change, mark gpio7 as no-reset and
no-idle on init.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
	v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
		cut -d 'x' -f2|tr [a-z] [A-Z]`;
	HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
	echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.

Fixes: 6e58b8f1 ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.

Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.

CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.

So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.

Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.

Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.

This patch also gets rid of the below warning when NAND is
accessed for the first time.

omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.

For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.

For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This reverts commit 150b8be3.

The I2C core's per-adapter locks can't protect from IRQs, so the driver still
needs a spinlock to protect the register accesses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull hwmon bugfix from Guenter Roeck:
 "Fix a bug in the ds1621 driver"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (ds1621) Update zbits after conversion rate change

Merge tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform drivers fixes from Darren Hart:
 "This is my first pull request since taking on maintenance for the
  platform-drivers-x86 tree from Matthew Garrett.  These have passed my
  build testing and been run through Fengguang's LKP tests.  Due to
  timing this round, these have not spent any time in linux-next.  I
  have asked Stephen to include my for-next branch in linux-next going
  forward, once he's back from vacation.

  Details from tag:

   - toshiba_acpi: re-enable hotkeys and cleanups
   - ideapad-laptop: revert touchpad disable, and cleanup static/const
     usage
   - MAINTAINERS: update platform-drivers-x86 maintainer and tree"

* tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
  platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
  ideapad-laptop: Constify DMI table for real!
  Revert "ideapad-laptop: Disable touchpad interface on Yoga models"
  MAINTAINERS: Update platform-drivers-x86 maintainer and tree

Pull sound fixes from Takashi Iwai:
 "This time it contains a bunch of small ASoC fixes that slipped from in
  previous updates, in addition to the usual HD-audio fixes and the
  regression fixes for FireWire updates in 3.17.

  All commits are reasonably small fixes"

* tag 'sound-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix COEF setups for ALC1150 codec
  ASoC: simple-card: Fix bug of wrong decrement DT node's refcount
  ALSA: hda - Fix digital mic on Acer Aspire 3830TG
  ASoC: omap-twl4030: Fix typo in 2nd dai link's platform_name
  ALSA: firewire-lib/dice: add arrangements of PCM pointer and interrupts for Dice quirk
  ALSA: dice: fix wrong channel mappping at higher sampling rate
  ASoC: cs4265: Fix setting of functional mode and clock divider
  ASoC: cs4265: Fix clock rates in clock map table
  ASoC: rt5677: correct mismatch widget name
  ASoC: rt5640: Do not allow regmap to use bulk read-write operations
  ASoC: tegra: Fix typo in include guard
  ASoC: da732x: Fix typo in include guard
  ASoC: core: fix .info for SND_SOC_BYTES_TLV
  ASoC: rcar: Use && instead of & for boolean expressions
  ASoC: Use dev_set_name() instead of init_name
  ASoC: axi: Fix ADI AXI SPDIF specification

here's a couple of display regression fixes for 3.17.

* tag 'drm-intel-fixes-2014-09-03' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Fix lock dropping in intel_tv_detect()
  drm/i915: handle G45/GM45 pulse detection connected state.