The device tree bindings are in two copies and also should be
consolidated into a single Faraday Technology FTWDT010
binding since we uncovered that this IP part is a standard
IP from Faraday.

Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Correct typo in comment "insterted" -> "inserted".
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This converts the GPIO watchdog driver to use GPIO descriptors
instead of relying on the old method to read out GPIO numbers
from the device tree and then using those with the old GPIO
API.

The descriptor API keeps track of whether the line is active
low so we can remove all active low handling and rely on the
GPIO descriptor to deal with this for us.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This add "dev" and "np" variables to make the probe() function
a bit easier to read.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The only way of stopping the watchdog is by resetting it.
Add the watchdog op for stopping the device and reset if
a reset line is provided.

At same time WDOG_HW_RUNNING should be remove from dw_wdt_start.
As commented by Guenter Roeck:
dw_wdt sets WDOG_HW_RUNNING in its open function. Result is
that the kref_get() in watchdog_open() won't be executed. But then
kref_put() in close will be called since the watchdog now does stop.
This causes the imbalance.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Probing at device_initcall time lead to perverse cases where the
watchdog was probed after, say, I2C devices, which then leaves a
potentially running watchdog at the mercy of I2C device behaviour and
bus conditions.

Load the watchdog driver early to ensure that the kernel is patting it
well before initialising peripherals.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The driver also supports the watchdog in the AST25xx series, and
may work on earlier SoCs as well.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Apseed sounds like a good name for a web/mobile start-up incubator, but
isn't a reflection of Aspeed themselves.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

An unintended post-condition of probe() is that the watchdog is
disabled. This behaviour was introduced by an unnecessary write to the
control register to configure the hardware based on the devicetree. The
write is unnecessary because the cached control value that is
manipulated by the code parsing the devicetree is eventually written by
aspeed_wdt_enable(), which is when we care how the control register
should be configured.

Remove the write to restore expected behaviour.

Fixes: b7f0b8ad ("drivers/watchdog: ASPEED reference dev tree properties for config")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Suggested-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The watchdog unit present in the JZ4780 works the same as the one in the
JZ4740.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add a watchdog driver for the Realtek RTD1295 SoC.

Based on QNAP's arch/arm/mach-rtk119x/driver/rtk_watchdog.c code and
mach-rtk119x/driver/dc2vo/fpga/include/iso_reg.h register defines.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add a binding for the Realtek RTD1295 watchdog.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Having a co-maintainer will enable us to be more flexible with
pull requests.

Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This corrects:
commit cce78da7 ("watchdog: hpwdt: Add check for UEFI bits")

The test on HPE SMBIOS extension type 219 record "Misc Features"
bits for UEFI support is incorrect.  The definition of the Misc Features
bits in the HPE SMBIOS OEM Extensions specification (and related
firmware) was changed to use a different pair of bits to
represent UEFI supported.  Howerver, a corresponding change
to Linux was missed.

Current code/platform work because the iCRU test is working.
But purpose of cce78da7 is to ensure correct functionality
on future systems where iCRU isn't supported.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Commit da2a68b3 ("watchdog: Enable COMPILE_TEST where possible")
enabled building the Indy watchdog driver when COMPILE_TEST is enabled.
However, the driver makes reference to symbols that are only defined for
certain platforms are selected in the config. These platforms select
SGI_HAS_INDYDOG. Without this, link time errors result, for example
when building a MIPS allyesconfig.

drivers/watchdog/indydog.o: In function `indydog_write':
indydog.c:(.text+0x18): undefined reference to `sgimc'
indydog.c:(.text+0x1c): undefined reference to `sgimc'
drivers/watchdog/indydog.o: In function `indydog_start':
indydog.c:(.text+0x54): undefined reference to `sgimc'
indydog.c:(.text+0x58): undefined reference to `sgimc'
drivers/watchdog/indydog.o: In function `indydog_stop':
indydog.c:(.text+0xa4): undefined reference to `sgimc'
drivers/watchdog/indydog.o:indydog.c:(.text+0xa8): more undefined
references to `sgimc' follow
make: *** [Makefile:1005: vmlinux] Error 1

Fix this by ensuring that CONFIG_INDIDOG can only be selected when the
necessary dependent platform symbols are built in.

Fixes: da2a68b3 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: <stable@vger.kernel.org> # 4.11 +
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: James Hogan <james.hogan@mips.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

If handle_boot_enabled is set to 0, the watchdog driver module use
counter will not be increased and kref_get() will not be called when
registering the watchdog. Subsequently, on open, this does not happen
either because the code believes that it was already done because the
hardware watchdog is marked as running.

We could introduce a state variable to indicate this state, but let's
just increase the module use counter and call kref_get() unconditionally
if the hardware watchdog is running when a driver is registering itself
to keep the code simple.

Fixes: 2501b015 ("watchdog: core: add option to avoid early ...")
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

If a watchdog driver's open function sets WDOG_HW_RUNNING with the
expectation that the watchdog can not be stopped, but then stops the
watchdog anyway in its stop function, kref_get() wil not be called in
watchdog_open(). If the watchdog then stops on close, WDOG_HW_RUNNING
will be cleared and kref_put() will be called, causing a kref imbalance.
As result the character device data structure will be released, which in
turn will cause the system to crash on the next call to watchdog_open().

Fixes: ee142889 ("watchdog: Introduce WDOG_HW_RUNNING flag")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull rdma fixes from Jason Gunthorpe:
 "More fixes from testing done on the rc kernel, including more SELinux
  testing. Looking forward, lockdep found regression today in ipoib
  which is still being fixed.

  Summary:

   - Fix for SELinux on the umad SMI path. Some old hardware does not
     fill the PKey properly exposing another bug in the newer SELinux
     code.

   - Check the input port as we can exceed array bounds from this user
     supplied value

   - Users are unable to use the hash field support as they want due to
     incorrect checks on the field restrictions, correct that so the
     feature works as intended

   - User triggerable oops in the NETLINK_RDMA handler

   - cxgb4 driver fix for a bad interaction with CQ flushing in iser
     caused by patches in this merge window, and bad CQ flushing during
     normal close.

   - Unbalanced memalloc_noio in ipoib in an error path"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/ipoib: Restore MM behavior in case of tx_ring allocation failure
  iw_cxgb4: only insert drain cqes if wq is flushed
  iw_cxgb4: only clear the ARMED bit if a notification is needed
  RDMA/netlink: Fix general protection fault
  IB/mlx4: Fix RSS hash fields restrictions
  IB/core: Don't enforce PKey security on SMI MADs
  IB/core: Bound check alternate path port number

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes for the AT24 I2C eeprom driver and some minor corrections
  for I2C bus drivers"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: piix4: Fix port number check on release
  i2c: stm32: Fix copyrights
  i2c-cht-wc: constify platform_device_id
  eeprom: at24: change nvmem stride to 1
  eeprom: at24: fix I2C device selection for runtime PM

Pull NFS client fixes from Anna Schumaker:
 "This has two stable bugfixes, one to fix a BUG_ON() when
  nfs_commit_inode() is called with no outstanding commit requests and
  another to fix a race in the SUNRPC receive codepath.

  Additionally, there are also fixes for an NFS client deadlock and an
  xprtrdma performance regression.

  Summary:

  Stable bugfixes:
   - NFS: Avoid a BUG_ON() in nfs_commit_inode() by not waiting for a
     commit in the case that there were no commit requests.
   - SUNRPC: Fix a race in the receive code path

  Other fixes:
   - NFS: Fix a deadlock in nfs client initialization
   - xprtrdma: Fix a performance regression for small IOs"

* tag 'nfs-for-4.15-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC: Fix a race in the receive code path
  nfs: don't wait on commit in nfs_commit_inode() if there were no commit requests
  xprtrdma: Spread reply processing over more CPUs
  nfs: fix a deadlock in nfs client initialization

This reverts commits 5c9d2d5c, c7da82b8, and e7fe7b5c.

We'll probably need to revisit this, but basically we should not
complicate the get_user_pages_fast() case, and checking the actual page
table protection key bits will require more care anyway, since the
protection keys depend on the exact state of the VM in question.

Particularly when doing a "remote" page lookup (ie in somebody elses VM,
not your own), you need to be much more careful than this was.  Dave
Hansen says:

 "So, the underlying bug here is that we now a get_user_pages_remote()
  and then go ahead and do the p*_access_permitted() checks against the
  current PKRU. This was introduced recently with the addition of the
  new p??_access_permitted() calls.

  We have checks in the VMA path for the "remote" gups and we avoid
  consulting PKRU for them. This got missed in the pkeys selftests
  because I did a ptrace read, but not a *write*. I also didn't
  explicitly test it against something where a COW needed to be done"

It's also not entirely clear that it makes sense to check the protection
key bits at this level at all.  But one possible eventual solution is to
make the get_user_pages_fast() case just abort if it sees protection key
bits set, which makes us fall back to the regular get_user_pages() case,
which then has a vma and can do the check there if we want to.

We'll see.

Somewhat related to this all: what we _do_ want to do some day is to
check the PAGE_USER bit - it should obviously always be set for user
pages, but it would be a good check to have back.  Because we have no
generic way to test for it, we lost it as part of moving over from the
architecture-specific x86 GUP implementation to the generic one in
commit e585513b ("x86/mm/gup: Switch GUP to the generic
get_user_page_fast() implementation").

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.

 2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
    Brueckner.

 3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
    Berg.

 4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.

 5) Don't advertise gigabit in sh_eth when not available, from Thomas
    Petazzoni.

 6) Check network namespace when delivering to netlink taps, from Kevin
    Cernekee.

 7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.

 8) Use correct address in TCP md5 lookups when replying to an incoming
    segment, from Christoph Paasch.

 9) Add schedule points to BPF map alloc/free, from Eric Dumazet.

10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
    from Eric Dumazet.

11) Fix SKB leak in tipc, from Jon Maloy.

12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.

13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.

14) Add some new qmi_wwan device IDs, from Daniele Palmas.

15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net: qcom/emac: Reduce timeout for mdio read/write
  net: sched: fix static key imbalance in case of ingress/clsact_init error
  net: sched: fix clsact init error path
  ip_gre: fix wrong return value of erspan_rcv
  net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
  pkt_sched: Remove TC_RED_OFFLOADED from uapi
  net: sched: Move to new offload indication in RED
  net: sched: Add TCA_HW_OFFLOAD
  net: aquantia: Increment driver version
  net: aquantia: Fix typo in ethtool statistics names
  net: aquantia: Update hw counters on hw init
  net: aquantia: Improve link state and statistics check interval callback
  net: aquantia: Fill in multicast counter in ndev stats from hardware
  net: aquantia: Fill ndev stat couters from hardware
  net: aquantia: Extend stat counters to 64bit values
  net: aquantia: Fix hardware DMA stream overload on large MRRS
  net: aquantia: Fix actual speed capabilities reporting
  sock: free skb in skb_complete_tx_timestamp on error
  s390/qeth: update takeover IPs after configuration change
  s390/qeth: lock IP table while applying takeover changes
  ...

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 4.15-rc4.

  There is the usual handful gadget/dwc2/dwc3 fixes as always, for
  reported issues. But the most important things in here is the core fix
  from Alan Stern to resolve a nasty security bug (my first attempt is
  reverted, Alan's was much cleaner), as well as a number of usbip fixes
  from Shuah Khan to resolve those reported security issues.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: core: prevent malicious bNumInterfaces overflow
  Revert "USB: core: only clean up what we allocated"
  USB: core: only clean up what we allocated
  Revert "usb: gadget: allow to enable legacy drivers without USB_ETH"
  usb: gadget: webcam: fix V4L2 Kconfig dependency
  usb: dwc2: Fix TxFIFOn sizes and total TxFIFO size issues
  usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3
  usb: dwc3: of-simple: set dev_pm_ops
  usb: dwc3: of-simple: fix missing clk_disable_unprepare
  usb: dwc3: gadget: Wait longer for controller to end command processing
  usb: xhci: fix TDS for MTK xHCI1.1
  xhci: Don't add a virt_dev to the devs array before it's fully allocated
  usbip: fix stub_send_ret_submit() vulnerability to null transfer_buffer
  usbip: prevent vhci_hcd driver from leaking a socket pointer address
  usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input
  usbip: fix stub_rx: get_pipe() to validate endpoint number
  tools/usbip: fixes potential (minor) "buffer overflow" (detected on recent gcc with -Werror)
  USB: uas and storage: Add US_FL_BROKEN_FUA for another JMicron JMS567 ID
  usb: musb: da8xx: fix babble condition handling

Pull staging fixes from Greg KH:
 "Here are some small staging driver fixes for 4.15-rc4.

  One patch for the ccree driver to prevent an unitialized value from
  being returned to a caller, and the other fixes a logic error in the
  pi433 driver"

* tag 'staging-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: pi433: Fixes issue with bit shift in rf69_get_modulation
  staging: ccree: Uninitialized return in ssi_ahash_import()

Pull virtio regression fixes from Michael Tsirkin:
 "Fixes two issues in the latest kernel"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_mmio: fix devm cleanup
  ptr_ring: fix up after recent ptr_ring changes

Merge tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - fix a particularly nasty DM core bug in a 4.15 refcount_t conversion.

 - fix various targets to dm_register_target after module __init
   resources created; otherwise racing lvm2 commands could result in a
   NULL pointer during initialization of associated DM kernel module.

 - fix regression in bio-based DM multipath queue_if_no_path handling.

 - fix DM bufio's shrinker to reclaim more than one buffer per scan.

* tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm bufio: fix shrinker scans when (nr_to_scan < retain_target)
  dm mpath: fix bio-based multipath queue_if_no_path handling
  dm: fix various targets to dm_register_target after module __init resources created
  dm table: fix regression from improper dm_dev_internal.count refcount_t conversion

Pull SCSI fixes from James Bottomley:
 "The most important one is the bfa fix because it's easy to oops the
  kernel with this driver (this includes the commit that corrects the
  compiler warning in the original), a regression in the new timespec
  conversion in aacraid and a regression in the Fibre Channel ELS
  handling patch.

  The other three are a theoretical problem with termination in the
  vendor/host matching code and a use after free in lpfc.

  The additional patches are a fix for an I/O hang in the mq code under
  certain circumstances and a rare oops in some debugging code"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: core: Fix a scsi_show_rq() NULL pointer dereference
  scsi: MAINTAINERS: change FCoE list to linux-scsi
  scsi: libsas: fix length error in sas_smp_handler()
  scsi: bfa: fix type conversion warning
  scsi: core: run queue if SCSI device queue isn't ready and queue is idle
  scsi: scsi_devinfo: cleanly zero-pad devinfo strings
  scsi: scsi_devinfo: handle non-terminated strings
  scsi: bfa: fix access to bfad_im_port_s
  scsi: aacraid: address UBSAN warning regression
  scsi: libfc: fix ELS request handling
  scsi: lpfc: Use after free in lpfc_rq_buf_free()

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC fixes:

   - fix use of uninitialized drv_typ variable

   - apply NO_CMD23 quirk to some specific SD cards to make them work"

* tag 'mmc-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: core: apply NO_CMD23 quirk to some specific cards
  mmc: core: properly init drv_type

Pull ceph fix from Ilya Dryomov:
 "CephFS inode trimming fix from Zheng, marked for stable"

* tag 'ceph-for-4.15-rc4' of git://github.com/ceph/ceph-client:
  ceph: drop negative child dentries before try pruning inode's alias

Pull overlayfs fixes from Miklos Szeredi:

 - fix incomplete syncing of filesystem

 - fix regression in readdir on ovl over 9p

 - only follow redirects when needed

 - misc fixes and cleanups

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix overlay: warning prefix
  ovl: Use PTR_ERR_OR_ZERO()
  ovl: Sync upper dirty data when syncing overlayfs
  ovl: update ctx->pos on impure dir iteration
  ovl: Pass ovl_get_nlink() parameters in right order
  ovl: don't follow redirects if redirect_dir=off

Currently mdio read/write takes around ~115us as the timeout
between status check is set to 100us.
By reducing the timeout to 1us mdio read/write takes ~15us to
complete. This improves the link up event response.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull arm64 fixes from Will Deacon:
 "There are some significant fixes in here for FP state corruption,
  hardware access/dirty PTE corruption and an erratum workaround for the
  Falkor CPU.

  I'm hoping that things finally settle down now, but never say never...

  Summary:

   - Fix FPSIMD context switch regression introduced in -rc2

   - Fix ABI break with SVE CPUID register reporting

   - Fix use of uninitialised variable

   - Fixes to hardware access/dirty management and sanity checking

   - CPU erratum workaround for Falkor CPUs

   - Fix reporting of writeable+executable mappings

   - Fix signal reporting for RAS errors"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fpsimd: Fix copying of FP state from signal frame into task struct
  arm64/sve: Report SVE to userspace via CPUID only if supported
  arm64: fix CONFIG_DEBUG_WX address reporting
  arm64: fault: avoid send SIGBUS two times
  arm64: hw_breakpoint: Use linux/uaccess.h instead of asm/uaccess.h
  arm64: Add software workaround for Falkor erratum 1041
  arm64: Define cputype macros for Falkor CPU
  arm64: mm: Fix false positives in set_pte_at access/dirty race detection
  arm64: mm: Fix pte_mkclean, pte_mkdirty semantics
  arm64: Initialise high_memory global variable earlier

Move static key increments to the beginning of the init function
so they pair 1:1 with decrements in ingress/clsact_destroy,
which is called in case ingress/clsact_init fails.

Fixes: 6529eaba ("net: sched: introduce tcf block infractructure")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since in qdisc_create, the destroy op is called when init fails, we
don't do cleanup in init and leave it up to destroy.
This fixes use-after-free when trying to put already freed block.

Fixes: 6e40cf2d ("net: sched: use extended variants of block_get/put in ingress and clsact qdiscs")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes:

   - fix the s2ram regression related to confusion around segment
     register restoration, plus related cleanups that make the code more
     robust

   - a guess-unwinder Kconfig dependency fix

   - an isoimage build target fix for certain tool chain combinations

   - instruction decoder opcode map fixes+updates, and the syncing of
     the kernel decoder headers to the objtool headers

   - a kmmio tracing fix

   - two 5-level paging related fixes

   - a topology enumeration fix on certain SMP systems"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Resync objtool's instruction decoder source code copy with the kernel's latest version
  x86/decoder: Fix and update the opcodes map
  x86/power: Make restore_processor_context() sane
  x86/power/32: Move SYSENTER MSR restoration to fix_processor_context()
  x86/power/64: Use struct desc_ptr for the IDT in struct saved_context
  x86/unwinder/guess: Prevent using CONFIG_UNWINDER_GUESS=y with CONFIG_STACKDEPOT=y
  x86/build: Don't verify mtools configuration file for isoimage
  x86/mm/kmmio: Fix mmiotrace for page unaligned addresses
  x86/boot/compressed/64: Print error if 5-level paging is not supported
  x86/boot/compressed/64: Detect and handle 5-level paging at boot-time
  x86/smpboot: Do not use smp_num_siblings in __max_logical_packages calculation

Pull locking fixes from Ingo Molnar:
 "Misc fixes:

   - Fix a S390 boot hang that was caused by the lock-break logic.
     Remove lock-break to begin with, as review suggested it was
     unreasonably fragile and our confidence in its continued good
     health is lower than our confidence in its removal.

   - Remove the lockdep cross-release checking code for now, because of
     unresolved false positive warnings. This should make lockdep work
     well everywhere again.

   - Get rid of the final (and single) ACCESS_ONCE() straggler and
     remove the API from v4.15.

   - Fix a liblockdep build warning"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/lib/lockdep: Add missing declaration of 'pr_cont()'
  checkpatch: Remove ACCESS_ONCE() warning
  compiler.h: Remove ACCESS_ONCE()
  tools/include: Remove ACCESS_ONCE()
  tools/perf: Convert ACCESS_ONCE() to READ_ONCE()
  locking/lockdep: Remove the cross-release locking checks
  locking/core: Remove break_lock field when CONFIG_GENERIC_LOCKBREAK=y
  locking/core: Fix deadlock during boot on systems with GENERIC_LOCKBREAK

Pull scheduler fixes from Ingo Molnar:
 "Two fixes: a crash fix for an ARM SoC platform, and kernel-doc
  warnings fixes"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/rt: Do not pull from current CPU if only one CPU to pull
  sched/core: Fix kernel-doc warnings after code movement

Pull perf tooling fix from Ingo Molnar:
 "Synchronize kernel <-> tooling headers to resolve two build warnings
  in the perf build"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/headers: Synchronize kernel <-> tooling headers