6e28b000 ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.

Fixes: 42a7b32b ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The default fix broadcast window size is currently set to 20 packets.
This is a very low value, set at a time when we were still testing on
10 Mb/s hubs, and a change to it is long overdue.

Commit 7845989c ("net: tipc: fix stall during bclink wakeup procedure")
revealed a problem with this low value. For messages of importance LOW,
the backlog queue limit will be  calculated to 30 packets, while a
single, maximum sized message of 66000 bytes, carried across a 1500 MTU
network consists of 46 packets.

This leads to the following scenario (among others leading to the same
situation):

1: Msg 1 of 46 packets is sent. 20 packets go to the transmit queue, 26
   packets to the backlog queue.
2: Msg 2 of 46 packets is attempted sent, but rejected because there is
   no more space in the backlog queue at this level. The sender is added
   to the wakeup queue with a "pending packets chain size" number of 46.
3: Some packets in the transmit queue are acked and released. We try to
   wake up the sender, but the pending size of 46 is bigger than the LOW
   wakeup limit of 30, so this doesn't happen.
5: Subsequent acks releases all the remaining buffers. Each time we test
   for the wakeup criteria and find that 46 still is larger than 30,
   even after both the transmit and the backlog queues are empty.
6: The sender is never woken up and given a chance to send its message.
   He is stuck.

We could now loosen the wakeup criteria (used by link_prepare_wakeup())
to become equal to the send criteria (used by tipc_link_xmit()), i.e.,
by ignoring the "pending packets chain size" value altogether, or we can
just increase the queue limits so that the criteria can be satisfied
anyway. There are good reasons (potentially multiple waiting senders) to
not opt for the former solution, so we choose the latter one.

This commit fixes the problem by giving the broadcast link window a
default value of 50 packets. We also introduce a new minimum link
window size BCLINK_MIN_WIN of 32, which is enough to always avoid the
described situation. Finally, in order to not break any existing users
which may set the window explicitly, we enforce that the window is set
to the new minimum value in case the user is trying to set it to
anything lower.

Fixes: 7845989c ("net: tipc: fix stall during bclink wakeup procedure")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is decrementing the pointer, instead of the value stored in the
pointer.  KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes xennet_create_queues() may failed to created all requested
queues, we need to update num_queues to real created to avoid NULL
pointer dereference.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

reset transport and unlock if misc_register failed.
Signed-off-by: Gao feng <omarapazanadi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Philipp Kirchhofer says:

====================
net: mv643xx_eth: TSO TX data corruption fixes

as previously discussed [1] the mv643xx_eth driver has some
issues with data corruption when using TCP segmentation offload (TSO).

The following patch set improves this situation by fixing two data
corruption bugs in the TSO TX path.

Before applying the patches repeatedly accessing large files located on
a SMB share on my NSA325 NAS with TSO enabled resulted in different
hash sums, which confirmed that data corruption is happening during
file transfer. After applying the patches the hash sums were the same.

As this is my first patch submission please feel free to point out any
issues with the patch set.

[1] http://thread.gmane.org/gmane.linux.network/336530
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent a race between the TX DMA engine and the CPU the writing of the
first transmit descriptor must be deferred until all following descriptors
have been updated. The network card may otherwise start transmitting before
all packet descriptors are set up correctly, which leads to data corruption
or an aborted transmit operation.

This deferral is already done in the non-TSO TX path, implement it also in
the TSO TX path.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TX DMA engine requires that buffers with a size of 8 bytes or smaller
must be 64 bit aligned. This requirement may be violated when doing TSO,
as in this case larger skb frags can be broken up and transmitted in small
parts with then inappropriate alignment.

Fix this by checking for proper alignment before handing a buffer to the
DMA engine. If the data is misaligned realign it by copying it into the
TSO header data area.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiko Schocher says:

====================
net, phy, smsc: add posibility to disable energy detect mode

On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Therefore the property "smsc,disable-energy-detect" is
introduced.

Patch 1 introduces phy-handle support for the ti,cpsw
driver. This is needed now for the smsc phy.

Patch 2 adds the disable energy mode functionality
to the smsc phy

Changes in v2:
- add comments from Florian Fainelli
  - I did not change disable property name into enable
    because I fear to break existing behaviour
  - add smsc vendor prefix
  - remove CONFIG_OF and use __maybe_unused
  - introduce "phy-handle" ability into ti,cpsw
    driver, so I can remove bogus:
      if (!of_node && dev->parent->of_node)
          of_node = dev->parent->of_node;
    construct. Therefore new patch for the ti,cpsw
    driver is necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.

This results in a forced speed of 1000 and RX/TX failure.

Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Account for extra headroom in ath9k driver, from Felix Fietkau.

 2) Fix OOPS in pppoe driver due to incorrect socket state transition,
    from Guillaume Nault.

 3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.

 4) Power management fixes for iwlwifi, from Johannes Berg.

 5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.

 6) Fix dst_entry usage in ARP replies, from Jiri Benc.

 7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.

 8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.

 9) Various resource allocation/freeing cures in DSA< from Neil
    Armstrong.

10) A series of bug fixes in the openvswitch conntrack support, from
    Joe Stringer.

11) Fix two cases (BPF and act_mirred) where we have to clean the sender
    cpu stored in the SKB before transmitting.  From WANG Cong and
    Alexei Starovoitov.

12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
    Achiad Shochat.

13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
    configuration via ethtool.  From Yuval Mintz.

14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
    'dev' is NULL, from Eric Biederman.

15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.

16) kcalloc() gstrings ethtool buffer before having driver fill it in,
    in order to prevent kernel memory leaking.  From Joe Perches.

17) Fix mixxing rt6_info initialization for blackhole routes, from
    Martin KaFai Lau.

18) Kill VLAN regression in via-rhine, from Andrej Ota.

19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.

20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.

21) Scrube SKBs when pushing them between namespaces in openvswitch,
    from Joe Stringer.

22) bcmgenet enables link interrupts too early, fix from Florian
    Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
  net: bcmgenet: Fix early link interrupt enabling
  tunnels: Don't require remote endpoint or ID during creation.
  openvswitch: Scrub skb between namespaces
  xen-netback: correctly check failed allocation
  net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
  netlink: Trim skb to alloc size to avoid MSG_TRUNC
  net: add pfmemalloc check in sk_add_backlog()
  via-rhine: fix VLAN receive handling regression.
  ipv6: Initialize rt6_info properly in ip6_blackhole_route()
  ipv6: Move common init code for rt6_info to a new function rt6_info_init()
  Bluetooth: Fix initializing conn_params in scan phase
  Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
  Bluetooth: Fix remove_device behavior for explicit connects
  Bluetooth: Fix LE reconnection logic
  Bluetooth: Fix reference counting for LE-scan based connections
  Bluetooth: Fix double scan updates
  mlxsw: core: Fix race condition in __mlxsw_emad_transmit
  tipc: move fragment importance field to new header position
  ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
  tipc: eliminate risk of stalled link synchronization
  ...

Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.

Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.

Fixes: 6cc8e6d4 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-10-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi:

* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment

rtlwifi:

* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.

An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.

CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.

This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2015-10-16

First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.

The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.

The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.

I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.

netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.

Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).

It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.

This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull i2c fixes from Wolfram Sang:
 "Here are some bugfixes for the I2C subsystem.

  Kieran found a flaw in the recently renewed wake irq handling.  Mika
  handled a user bug report where the ACPI info turned out to be
  unusable.  I updated MAINTAINERS so that such bug reports will sooner
  get to the right people.  Geert pointed me to a problem of some i2c
  drivers regarding PM which I fixed"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
  MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
  i2c: designware-platdrv: enable RuntimePM before registering to the core
  i2c: s3c2410: enable RuntimePM before registering to the core
  i2c: rcar: enable RuntimePM before registering to the core
  i2c: return probe deferred status on dev_pm_domain_attach

ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:

  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: controller timed out

The values received from ACPI are (in fast mode):

  HCNT: 72
  LCNT: 160

this translates to following timings (input clock is 100MHz on Broadwell):

  tHIGH: 720 ns (spec min 600 ns)
  tLOW: 1600 ns (spec min 1300 ns)
  Bus period: 2920 ns (assuming 300 ns tf and tr)
  Bus speed: 342.5 kHz

Both tHIGH and tLOW are within the I2C specification.

The calculated values when ACPI parameters are not used are (in fast mode):

  HCNT: 87
  LCNT: 159

which translates to:

  tHIGH: 870 ns (spec min 600 ns)
  tLOW: 1590 ns (spec min 1300 ns)
  Bus period 3060 ns (assuming 300 ns tf and tr)
  Bus speed 326.8 kHz

These values are also within the I2C specification.

Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).

Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq/timer fixes from Thomas Gleixner:
 "irq: a fix for the new hierarchical MSI interrupt handling which
  unbreaks PCI=n configurations.

  timers: a fix for the new hrtimer clock offset update mechanism to
  ensure that the boot time offset is respected"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/msi: Do not use pci_msi_[un]mask_irq as default methods

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Increment clock_was_set_seq in timekeeping_init()

Greg reported crashes hitting the following check in __sk_backlog_rcv()

	BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));

The pfmemalloc bit is currently checked in sk_filter().

This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.

For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.

Fixes: b4b9e355 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input fixes from Dmitry Torokhov:
 "Just two small fixups to ads7846 touchscreen controller driver and
  Cypress touchpad driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: cyapa - fix the copy paste error on electrodes_rx value
  Input: ads7846 - correct the value got from SPI

Pull clk fix from Stephen Boyd:
 "Just one revert for Armada XP devices: the conversion to
  of_clk_get_parent_name() wasn't a direct translation, so we
  revert back to of_clk_get() + __clk_get_name().

  We could make of_clk_get_parent_name() more robust, but that
  may have unintended side-effects, so we'll do that in the
  next version"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"

Pull device mapper fixes from Mike Snitzer:
 "Two DM target error path cleanup fixes (one for stable in DM thinp and
  one for a v4.3-rc5 thinko in DM snapshot)"

* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm thin: fix missing pool reference count decrement in pool_ctr error path
  dm snapshot persistent: fix missing cleanup in persistent_ctr error path

Pull btrfs fixes from Chris Mason:
 "I have two more bug fixes for btrfs.

  My commit fixes a bug we hit last week at FB, a combination of lots of
  hard links and an admin command to resolve inode numbers.

  Dave is adding checks to make sure balance on current kernels ignores
  filters it doesn't understand.  The penalty for being wrong is just
  doing more work (not crashing etc), but it's a good fix"

* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix use after free iterating extrefs
  btrfs: check unsupported filters in balance arguments

Pull Ceph fixes from Sage Weil:
 "Just two small items from Ilya:

  The first patch fixes the RBD readahead to grab full objects.  The
  second fixes the write ops to prevent undue promotion when a cache
  tier is configured on the server side"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: use writefull op for object size writes
  rbd: set max_sectors explicitly

Pull power management and ACPI fixes from Rafael Wysocki:
 "These fix two recent regressions (ACPICA, the generic power domains
  framework) and one crash that may happen on specific hardware
  supported since 4.1 (intel_pstate).

  Specifics:

   - Fix a regression introduced by a recent ACPICA cleanup that
     uncovered a latent bug (Lv Zheng).

   - Fix a recent regression in the generic power domains framework that
     may cause it to violate PM QoS latency constraints in some cases
     (Ulf Hansson).

   - Fix an intel_pstate driver crash on the Knights Landing chips that
     do not update the MPERF counter as often as expected by the driver
     which may result in a divide by 0 (Srinivas Pandruvada)"

* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
  ACPICA: Tables: Fix FADT dependency regression
  PM / Domains: Fix validation of latency constraints in genpd governor

Pull drm fixes from Dave Airlie:
 "Nothing too crazy or exciting:

   - two MAINTAINERS entries that I didn't see the point in delaying.
   - one drm mst fix to stop sending uninitialised data to monitors
   - two amdgpu fixes
   - one radeon mst tiling fix
   - one vmwgfx regression fix
   - one virtio warning fix.

  I have found one locking problem that needs a bit of reorg to fix, but
  I'm not sure it's worth putting in -fixes as I don't think we've seen
  it hit in the real world ever, I just found it using the virtio-gpu
  driver when working on it.  I'll possibly send it next week once I've
  time to discuss with Daniel"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/virtio: use %llu format string form atomic64_t
  MAINTAINERS: Add myself as maintainer for the gma500 driver
  MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
  drm/amdgpu: Keep the pflip interrupts always enabled v7
  drm/amdgpu: adjust default dispclk (v2)
  drm/dp/mst: make mst i2c transfer code more robust.
  drm/radeon: attach tile property to mst connector
  drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware

Pull powerpc fixes from Michael Ellerman:
 - Re-enable CONFIG_SCSI_DH in our defconfigs
 - Remove unused os_area_db_id_video_mode
 - cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
 - cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
 - cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
 - cxl: Workaround malformed pcie packets on some cards from Philippe
 - cxl: Fix number of allocated pages in SPA from Christophe Lombard
 - Fix checkstop in native_hpte_clear() with lockdep from Cyril
 - Panic on unhandled Machine Check on powernv from Daniel
 - selftests/powerpc: Fix build failure of load_unaligned_zeropad test

* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  selftests/powerpc: Fix build failure of load_unaligned_zeropad test
  powerpc/powernv: Panic on unhandled Machine Check
  powerpc: Fix checkstop in native_hpte_clear() with lockdep
  cxl: Fix number of allocated pages in SPA
  cxl: Workaround malformed pcie packets on some cards
  cxl: fix leak of ctx->mapping when releasing kernel API contexts
  cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
  cxl: fix leak of IRQ names in cxl_free_afu_irqs()
  powerpc/ps3: Remove unused os_area_db_id_video_mode
  powerpc/configs: Re-enable CONFIG_SCSI_DH

Merge misc fixes from Andrew Morton:
 "6 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  sh: add copy_user_page() alias for __copy_user()
  lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
  mm, dax: fix DAX deadlocks
  memcg: convert threshold to bytes
  builddeb: remove debian/files before build
  mm, fs: obey gfp_mapping for add_to_page_cache()

copy_user_page() is needed by DAX.  Without this we get a compile error
for DAX on SH:

  fs/dax.c:280:2: error: implicit declaration of function `copy_user_page' [-Werror=implicit-function-declaration]
    copy_user_page(vto, (void __force *)vfrom, vaddr, to);
      ^

This was done with a random config that happened to include DAX support.

This patch has only been compile tested.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'

Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The following two locking commits in the DAX code:

commit 84317297 ("dax: fix race between simultaneous faults")
commit 46c043ed ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")

introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel.  The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:

  https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").

This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

page_counter_memparse() returns pages for the threshold, while
mem_cgroup_usage() returns bytes for memory usage.  Convert the
threshold to bytes.

Fixes: 3e32cb2e ("memcg: rename cgroup_event to mem_cgroup_event").
Signed-off-by: Shaohua Li <shli@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3716001b ("deb-pkg: add source package") added the ability to
create a debian changelog file.  This exposed that previously the
builddeb script hasn't cleared debian/files between builds.

As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty.  With outdated entries in debian/files, builddeb
script will exit with failure.  This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.

To fix the regression, remove debian/files before starting build and in
the generated clean rule.

Fixes: 3716001b ("deb-pkg: add source package")
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Michal Marek <mmarek@suse.cz>
Cc: maximilian attems <maks@stro.at>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>