- 18 Nov, 2014 5 commits
-
-
John W. Linville authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg <johan.hedberg@gmail.com> says: "Here's another bluetooth-next pull request for 3.19. We've got: - Various fixes, cleanups and improvements to ieee802154/mac802154 - Support for a Broadcom BCM20702A1 variant - Lots of lockdep fixes - Fixed handling of LE CoC errors that should trigger SMP" Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Fabio K authored
This variant requires the flag BTUSB_BCM_PATCHRAM to work. Relevant details from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3404 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=240A646F1XXX C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) The firmware was extracted from a Windows 8.1 64-bit installation and converted from 'hex' to 'hcd' for use in Linux. Under Windows it also identifies itself as BCM20702A0, but the firmware is named "BCM20702A1_001.002.014.1315.1356.hex" and is located in "%SYSTEMROOT%\system32\drivers\" (md5 67cf6bfdae61c4bb819a66da984f7913) (sha1 5f74cc6a9a3bf19ee0f8c3d01e4be34c609b188f) The same firmware file is also available as a download at http://www.asrock.com/mb/Intel/Z87E-ITX/?cat=Download&os=All marked as "Bluetooth driver ver:12.0.0.7820" 'hcd' file should be placed at "brcm/BCM20702A0-13d3-3404.hcd" inside the firmware directory (e.g. "/lib/firmware") Signed-off-by: Fabio K <healthkit@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Doing things like hci_conn_hash_flush() while holding the hdev lock is risky since its synchronous pending work cancellation could cause the L2CAP layer to try to reacquire the hdev lock. Right now there doesn't seem to be any obvious places where this would for certain happen but it's already enough to cause lockdep to start warning against the hdev and the work struct locks being taken in the "wrong" order: [ +0.000373] mgmt-tester/1603 is trying to acquire lock: [ +0.000292] ((&conn->pending_rx_work)){+.+.+.}, at: [<c104266d>] flush_work+0x0/0x181 [ +0.000270] but task is already holding lock: [ +0.000000] (&hdev->lock){+.+.+.}, at: [<c13b9a80>] hci_dev_do_close+0x166/0x359 [ +0.000000] which lock already depends on the new lock. [ +0.000000] the existing dependency chain (in reverse order) is: [ +0.000000] -> #1 (&hdev->lock){+.+.+.}: [ +0.000000] [<c105ea8f>] lock_acquire+0xe3/0x156 [ +0.000000] [<c140c663>] mutex_lock_nested+0x54/0x375 [ +0.000000] [<c13d644b>] l2cap_recv_frame+0x293/0x1a9c [ +0.000000] [<c13d7ca4>] process_pending_rx+0x50/0x5e [ +0.000000] [<c1041a3f>] process_one_work+0x21c/0x436 [ +0.000000] [<c1041e3d>] worker_thread+0x1be/0x251 [ +0.000000] [<c1045a22>] kthread+0x94/0x99 [ +0.000000] [<c140f801>] ret_from_kernel_thread+0x21/0x30 [ +0.000000] -> #0 ((&conn->pending_rx_work)){+.+.+.}: [ +0.000000] [<c105e158>] __lock_acquire+0xa07/0xc89 [ +0.000000] [<c105ea8f>] lock_acquire+0xe3/0x156 [ +0.000000] [<c1042696>] flush_work+0x29/0x181 [ +0.000000] [<c1042864>] __cancel_work_timer+0x76/0x8f [ +0.000000] [<c104288c>] cancel_work_sync+0xf/0x11 [ +0.000000] [<c13d4c18>] l2cap_conn_del+0x72/0x183 [ +0.000000] [<c13d8953>] l2cap_disconn_cfm+0x49/0x55 [ +0.000000] [<c13be37a>] hci_conn_hash_flush+0x7a/0xc3 [ +0.000000] [<c13b9af6>] hci_dev_do_close+0x1dc/0x359 [ +0.012038] [<c13bbe38>] hci_unregister_dev+0x6e/0x1a3 [ +0.000000] [<c12d33c1>] vhci_release+0x28/0x47 [ +0.000000] [<c10dd6a9>] __fput+0xd6/0x154 [ +0.000000] [<c10dd757>] ____fput+0xd/0xf [ +0.000000] [<c1044bb2>] task_work_run+0x6b/0x8d [ +0.000000] [<c1001bd2>] do_notify_resume+0x3c/0x3f [ +0.000000] [<c140fa70>] work_notifysig+0x29/0x31 [ +0.000000] other info that might help us debug this: [ +0.000000] Possible unsafe locking scenario: [ +0.000000] CPU0 CPU1 [ +0.000000] ---- ---- [ +0.000000] lock(&hdev->lock); [ +0.000000] lock((&conn->pending_rx_work)); [ +0.000000] lock(&hdev->lock); [ +0.000000] lock((&conn->pending_rx_work)); [ +0.000000] *** DEADLOCK *** Fully fixing this would require some quite heavy refactoring to change how the hdev lock and hci_conn instances are handled together. A simpler solution for now which this patch takes is to try ensure that the hdev workqueue is empty before proceeding with the various cleanup calls, including hci_conn_hash_flush(). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
The common short form of "randomizer" is "rand" in many places (including the Bluetooth specification). The shorter version also makes for easier to read code with less forced line breaks. This patch renames all occurences of "randomizer" to "rand" in the Bluetooth subsystem code. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
For now the mgmt commands dealing with remote OOB data are strictly BR/EDR-only. This patch fixes missing checks for the passed address type so that any non-BR/EDR value triggers the appropriate error response. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 17 Nov, 2014 35 commits
-
-
Sujith Manoharan authored
Currently, when a roc period expires, the offchannel timer calls ieee80211_remain_on_channel_expired(), but the roc state is cleared only when the queued work to switch to the operating channel gets a chance to run. This race is a problem because mac80211 can issue a new roc request in this window. To avoid this, handle roc completion in the offchannel timer itself. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
In a GO/STA setup, when we switch to the STA context, the channel context timer is scheduled with a period of half the beacon interval. If a beacon is received in this duration, the timer is adjusted to accommodate TSF sync done by the HW. But, if the actual channel switch is delayed for some reason, we end up rearming the timer every time a new beacon is received. Avoid this by doing the adjustment only once. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
If for some reason a beacon with a new NoA is not sent out, then reset the mgd_prepare_tx flag. Not doing this will result in a situation where a GO will send a new NoA when it shouldn't. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
This patch makes sure that pending roc/scan operations are cancelled properly when a new context is assigned/unassigned. The flush_work() call to flush out any scheduled channel context work is removed, instead, sc->mutex is dropped to allow any pending work to get a chance to complete by the channel scheduler. Also, increase the timeout to allow a switch to an active GO. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
When a pending roc or scan operation is cancelled, the offchannel operation is cleared, but the offchannel state in the main scheduler is not cleared. This causes problems since an active GO will try to process a stale offchannel request that was deferred earlier. Fix this by clearing the state when there is no pending offchannel (roc/scan) operation. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
The registers that control the on-chip thermometer need to be programmed based on the chainmask that the solution supports, not the chainmask that is present in the eeprom. Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
The base TSF is used for HW timers 0..7, but chips in the AR9003 family and above can support more generic timers. To use them, however, a second HW TSF needs to be enabled. This patch allows usage of the extra timers by starting the second TSF properly. The extra set of HW timers is apparently also present in AR9287, but we enable it only for the AR9003 family. Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
On some x86 platforms, the LED gpio is active high instead of active low. Identify such cards and modify the GPIO usage to make sure LED works properly. Cc: Russell Hu <rhu@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Miaoqing Pan authored
This patch updates the initvals for QCA953x v1.1 and v2.0 Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
* Duplicates have been marked. * New initvals for 1.1 and 2.0 versions. * xPA support. * Fix for low power issue. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Chun-Yeow Yeoh authored
In secured mesh, the unicast mgmt frame is encrypted using the same key that used for encrypting the unicast data frame. This patch "ath9k_htc_firmware: fix the offset of CCMP header for mesh data frame" applied to open-ath9k-htc-firmware allows the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately, this is not working and we still need CCMP encryption of transmitted management frames to be done in software. So this patch allows the software encryption for transmitted management frame to be done in software but remain the hardware decryption for received management frame. This patch is tested with the following hardwares: - TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] - AR9271 802.11n and managed to work with peer mesh STA equipped with ath9k. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Chun-Yeow Yeoh authored
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption for transmitted management frames to be done in software while the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption for received management frames to be done in software. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
Auto TDLS support is enabled per device. As of now add this feature only for SD8887. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
This patch adds support for parsing TDLS discovery frames. After parsing, we update peer RSSI information. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
This patch adds auto TDLS support to mwifiex. Auto TDLS functionality works as follows: 1. Whenever userspace application has triggered TDLS connection with any peer, driver would store this peer mac address details in its database. 2. After this driver whenever driver receives packet on direct link, it would store rssi and timestamp in peer information. 3. Whenever a packet is to be transmitted to non-AP peer in station mode, driver would check if TDLS link can be established by looking at peer RSSI information. Driver would initiate TDLS setup in such cases. 4. Periodic timer is used for updating peer information. 5. Auto TDLS peer list & timer are cleared during disconnection or driver unload. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
This patch adds WMM support for TDLS link. Patch add WMM info IE for TDLS setup request/response frames while WMM parameter for TDLS confirm frame. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
When Teardown event from FW is indicated to userspace, userspace would trigger tdls_oper handler to disable TDLS link. We need not do this explicitly here. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
RX packet descriptor structure has recently changed in FW. This patch updates rxpd accordingly. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Chun-Yeow Yeoh authored
We need to assign the hw queues for mesh interface. Otherwise, we are not able to bring up the mesh interface due to the IEEE80211_INVAL_HW_QUEUE error. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Oleksij Rempel authored
we can have here two variants. Add ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS which need more time to be done. So, make common-spectral ignore ATH9K_DEBUGFS option for now. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
kbuild test robot authored
drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static? Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
kbuild test robot authored
drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static? Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
This patch adds module load parameter driver_mode for mwifiex which would enable driver to create AP or P2P client interface while loading module. driver_mode is bitmap of interface modes for station, AP and P2P client. Station interface is created by default and is unaffected by driver_mode parameter. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ben Greear authored
When channel-context is not enabled, all vifs belong to the first context, but it is not configured as 'assigned'. Fix misc debugfs file to print out info for non-assigned contexts, and also print whether ctx is assigned or not. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
git://github.com/kvalo/athJohn W. Linville authored
Kalle Valo <kvalo@qca.qualcomm.com> says: "One ath6kl patch and rest for ath10k, but nothing really major which stands out. Most notable: o fix resume (Bartosz) o firmware restart is now faster and more reliable (Michal) o it's now possible to test hardware restart functionality without crashing the firmware using hw-restart parameter with simulate_fw_crash debugfs file (Michal)" Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Peter Oh authored
Fix to use v10.2 wmi call for firmware v10.2. It turned out that peer association function was using v10.1 wmi call for v10.2 firmware during code review. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Rajkumar Manoharan authored
This will enable AP mode to change channel width dynamically based on 20/40 intolerance report sent by associated client. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Rajkumar Manoharan authored
This patch would help bring up wifi interface with default board data in case of failures in otp download. It is useful for initial calibration. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Rajkumar Manoharan authored
For packet log, the transmitted frame 802.11 header alone is sufficient. Recording entire packet is also consuming lot of disk space. To optimize this, tx and rx data tracepoints are splitted into header and payload tracepoints. To record tx ieee80211 headers trace-cmd record -e ath10k_tx_hdr To record complete packets trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload Cc: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Alexander Aring authored
This patch changes the byteorder handling for short and panid handling. We now except to get little endian in nl802154 for these attributes. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch moves the 802.15.4 constraints WPAN_NUM_ defines into "net/ieee802154.h" which should contain all necessary 802.15.4 related information. Also rename these defines to a common name which is IEEE802154_MAX_CHANNEL and IEEE802154_MAX_PAGE. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch adds support for deleting a wpan interface via nl802154. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch adds support for setting an extended address while registration a new interface. If ieee802154_is_valid_extended_addr getting as parameter and invalid extended address then the perm address is fallback. This is useful to make some default handling while for example default registration of a wpan interface while phy registration. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch adds a new nl802154 command for adding a new interface according to a wpan phy via nl802154. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-