Commit 7ad2ed1d inadvertently mixed up a quirk flag's name and
broke SDR50 tuning override. Use correct NVQUIRK_ name.

Fixes: 7ad2ed1d ("mmc: tegra: enable UHS-I modes")
Cc: <stable@vger.kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/9aff1d859935e59edd81e4939e40d6c55e0b55f6.1578390388.git.mirq-linux@rere.qmqm.plSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Command Queuing was enabled completely for J721e controllers which lead
to partial enablement even for Am65x. Complete CQ implementation for
AM65x by adding the irq callback.

Fixes: f545702b ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-4-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The tuning data is leftover in the buffer after tuning. This can cause
issues in future data commands, especially with CQHCI. Reset the command
and data lines after tuning to continue from a clean state.

Fixes: 41fd4cae ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-3-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The MMC/SD controllers on am65x and j721e don't in fact detect the write
protect line as inverted. No issues were detected because of this
because the sdwp line is not connected on any of the evms. Fix this by
removing the flag.

Fixes: 1accbced ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-2-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The erratum A-009204 workaround patch was reverted because of
incorrect implementation.

8b6dc6b2 mmc: sdhci-of-esdhc: Revert "mmc: sdhci-of-esdhc: add
        erratum A-009204 support"

This patch is to re-implement the workaround (add a 5 ms delay
before setting SYSCTL[RSTD] to make sure all the DMA transfers
are finished).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20191219032335.26528-1-yangbo.lu@nxp.com
Fixes: 5dd19552 ("mmc: sdhci-of-esdhc: add erratum A-009204 support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.

This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.

Fixes: 8ee82bda ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Command queuing has been reported broken on some Lenovo systems based on
Intel GLK. This is likely a BIOS issue, so disable command queuing for
Intel GLK if the BIOS vendor string is "LENOVO".

Fixes: 8ee82bda ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-1-adrian.hunter@intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL

The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
	host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
	host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

This patch is to fix them.
	host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
	host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

Fixes: 05cb6b2a ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e4271 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.

Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This reverts commit 5dd19552.

First, the fix seems to be plain wrong, since the erratum suggests
waiting 5ms before setting setting SYSCTL[RSTD], but this msleep()
happens after the call of sdhci_reset() which is where that bit gets
set (if SDHCI_RESET_DATA is in mask).

Second, walking the whole device tree to figure out if some node has a
"fsl,p2020-esdhc" compatible string is hugely expensive - about 70 to
100 us on our mpc8309 board. Walking the device tree is done under a
raw_spin_lock, so this is obviously really bad on an -rt system, and a
waste of time on all.

In fact, since esdhc_reset() seems to get called around 100 times per
second, that mpc8309 now spends 0.8% of its time determining that
it is not a p2020. Whether those 100 calls/s are normal or due to some
other bug or misconfiguration, regularly hitting a 100 us
non-preemptible window is unacceptable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191204085447.27491-1-linux@rasmusvillemoes.dkSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: stable@vger.kernel.org
Fixes: 1ede5cb8 ("mmc: mediatek: Use data tune for CMD line tune")
Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The DDR_CONFIG register offset got updated after a specific
minor version of sdcc V4. This offset change has not been properly
taken care of while updating register changes for sdcc V5.

Correcting proper offset for this register.
Also updating this register value to reflect the recommended RCLK
delay.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ea738ec72-fa0f852d-20f8-474a-80b2-4b0ef63b132c-000000@us-west-2.amazonses.com
Fixes: f1535888 ("mmc: sdhci-msm: Define new Register address map")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This reverts commit c894e33d.

This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.

The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.

Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull rdma fixes from Doug Ledford:
 "A small collection of -rc fixes. Mostly. One API addition, but that's
  because we wanted to use it in a fix. There's also a bug fix that is
  going to render the 5.5 kernel's soft-RoCE driver incompatible with
  all soft-RoCE versions prior, but it's required to actually implement
  the protocol according to the RoCE spec and required in order for the
  soft-RoCE driver to be able to successfully work with actual RoCE
  hardware.

  Summary:

   - Update Steve Wise info

   - Fix for soft-RoCE crc calculations (will break back compatibility,
     but only with the soft-RoCE driver, which has had this bug since it
     was introduced and it is an on-the-wire bug, but will make
     soft-RoCE fully compatible with real RoCE hardware)

   - cma init fixup

   - counters oops fix

   - fix for mlx4 init/teardown sequence

   - fix for mkx5 steering rules

   - introduce a cleanup API, which isn't a fix, but we want to use it
     in the next fix

   - fix for mlx5 memory management that uses API in previous patch"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/mlx5: Fix device memory flows
  IB/core: Introduce rdma_user_mmap_entry_insert_range() API
  IB/mlx5: Fix steering rule of drop and count
  IB/mlx4: Follow mirror sequence of device add during device removal
  RDMA/counter: Prevent auto-binding a QP which are not tracked with res
  rxe: correctly calculate iCRC for unaligned payloads
  Update mailmap info for Steve Wise
  RDMA/cma: add missed unregister_pernet_subsys in init failure

Pull RISC-V fixes from Paul Walmsley:
 "Two minor build fixes:

   - Fix builds of the ELF loader when built with 'make -j1' (nommu
     only)

   - Fix CONFIG_SOC_SIFIVE builds when CONFIG_TTY is disabled (found
     during randconfig testing)"

* tag 'riscv/for-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: only select serial sifive if TTY is enabled
  riscv: Fix build dependency for loader

Pull xen fixes from Juergen Gross:
 "Two fixes: one for a resource accounting bug in some configurations
  and a fix for another patch which went into rc1"

* tag 'for-linus-5.5b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: fix ballooned page accounting without hotplug enabled
  xen-blkback: prevent premature module unload

Pull ksys_mount() and ksys_dup() removal from Dominik Brodowski:
 "This small series replaces all in-kernel calls to the
  userspace-focused ksys_mount() and ksys_dup() with calls to
  kernel-centric functions:

  For each replacement of ksys_mount() with do_mount(), one needs to
  verify that the first and third parameter (char *dev_name, char *type)
  are strings allocated in kernelspace and that the fifth parameter
  (void *data) is either NULL or refers to a full page (only occurence
  in init/do_mounts.c::do_mount_root()). The second and fourth
  parameters (char *dir_name, unsigned long flags) are passed by
  ksys_mount() to do_mount() unchanged, and therefore do not require
  particular care.

  Moreover, instead of pretending to be userspace, the opening of
  /dev/console as stdin/stdout/stderr can be implemented using in-kernel
  functions as well. Thereby, ksys_dup() can be removed for good"

[ This doesn't get rid of the special "kernel init runs with KERNEL_DS"
  case, but it at least removes _some_ of the users of "treat kernel
  pointers as user pointers for our magical init sequence".

  One day we'll hopefully be rid of it all, and can initialize our
  init_thread addr_limit to USER_DS.    - Linus ]

* 'remove-ksys-mount-dup' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
  fs: remove ksys_dup()
  init: unify opening /dev/console as stdin/stdout/stderr
  init: use do_mount() instead of ksys_mount()
  initrd: use do_mount() instead of ksys_mount()
  devtmpfs: use do_mount() instead of ksys_mount()

Merge tag 'Wimplicit-fallthrough-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull fall through fix from Gustavo Silva:
 "Fix compile error on sh by marking expected switch fall-through"

* tag 'Wimplicit-fallthrough-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  sh: kgdb: Mark expected switch fall-throughs

Pull SCSI fixes from James Bottomley:
 "24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
  rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
  scsi: iscsi: Avoid potential deadlock in iscsi_if_rx func
  scsi: iscsi: Fix a potential deadlock in the timeout handler
  scsi: smartpqi: Update attribute name to `driver_version`
  scsi: libsas: stop discovering if oob mode is disconnected
  scsi: ufs: Disable autohibern8 feature in Cadence UFS
  scsi: iscsi: qla4xxx: fix double free in probe
  scsi: ufs: Give an unique ID to each ufs-bsg
  scsi: qla2xxx: Add debug dump of LOGO payload and ELS IOCB
  scsi: qla2xxx: Ignore PORT UPDATE after N2N PLOGI
  scsi: qla2xxx: Don't defer relogin unconditonally
  scsi: qla2xxx: Send Notify ACK after N2N PLOGI
  scsi: qla2xxx: Configure local loop for N2N target
  scsi: qla2xxx: Fix PLOGI payload and ELS IOCB dump length
  scsi: qla2xxx: Don't call qlt_async_event twice
  scsi: qla2xxx: Allow PLOGI in target mode
  scsi: qla2xxx: Change discovery state before PLOGI
  scsi: qla2xxx: Drop superfluous INIT_WORK of del_work
  scsi: qla2xxx: Initialize free_work before flushing it
  scsi: qla2xxx: Use explicit LOGO in target mode
  scsi: qla2xxx: Ignore NULL pointer in tcm_qla2xxx_free_mcmd
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are six small fixes for some reported char/misc driver issues:

   - fix build warnings with new 'awk' with the raid6 code

   - four interconnect driver bugfixes

   - binder fix for reported problem

  All of these except the binder fix have been in linux-next with no
  reported issues. The binder fix is "new" but Todd says it is good as
  he has tested it :)"

* tag 'char-misc-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  binder: fix incorrect calculation for num_valid
  interconnect: qcom: msm8974: Walk the list safely on node removal
  interconnect: qcom: qcs404: Walk the list safely on node removal
  interconnect: qcom: sdm845: Walk the list safely on node removal
  interconnect: qcom: Fix Kconfig indentation
  lib: raid6: fix awk build warnings

Pull driver core fixes from Greg KH:
 "Here are two small driver core fixes to resolve some reported issues

  The first is to handle the much-reported (by the build systems)
  problem that superH does not boot anymore.

  The second handles an issue in the new platform logic that a number of
  people ran into with the automated tests in kbuild

  Both of these have been in linux-next with no reported issues"

* tag 'driver-core-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers: Fix boot problem on SuperH
  of/platform: Unconditionally pause/resume sync state during kernel init

Pull staging/IIO fixes from Greg KH:
 "Here are a number of small staging and IIO driver fixes for reported
  issues for 5.5-rc2

  Nothing major, a bunch of tiny IIO driver issues resolved, and some
  staging driver fixes for things that people ran into with 5.5-rc1.
  Full details are in the shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
  fbtft: Fix the initialization from property algorithm
  staging: rtl8712: fix interface sanity check
  staging: rtl8188eu: fix interface sanity check
  staging: gigaset: add endpoint-type sanity check
  staging: gigaset: fix illegal free on probe errors
  staging: gigaset: fix general protection fault on probe
  staging: vchiq: call unregister_chrdev_region() when driver registration fails
  staging: exfat: fix multiple definition error of `rename_file'
  staging/wlan-ng: add CRC32 dependency in Kconfig
  staging: hp100: Fix build error without ETHERNET
  staging: fbtft: Do not hardcode SPI CS polarity inversion
  staging: exfat: properly support discard in clr_alloc_bitmap()
  staging/octeon: Mark Ethernet driver as BROKEN
  iio: adc: max9611: Fix too short conversion time delay
  iio: ad7949: fix channels mixups
  iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
  iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
  iio: imu: st_lsm6dsx: fix decimation factor estimation
  iio: imu: inv_mpu6050: fix temperature reporting using bad unit
  iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
  ...

Pull USB fixes from Greg KH:
 "Here are some small USB driver fixes for reported issues for 5.5-rc2

  There's the usual gadget and xhci fixes, as well as some other
  problems that syzbot has been finding during it's fuzzing runs. Full
  details are in the shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
  usb: dwc3: pci: add ID for the Intel Comet Lake -H variant
  xhci: make sure interrupts are restored to correct state
  xhci: handle some XHCI_TRUST_TX_LENGTH quirks cases as default behaviour.
  xhci: Increase STS_HALT timeout in xhci_suspend()
  usb: xhci: only set D3hot for pci device
  xhci: fix USB3 device initiated resume race with roothub autosuspend
  xhci: Fix memory leak in xhci_add_in_port()
  USB: Fix incorrect DMA allocations for local memory pool drivers
  usb: gadget: fix wrong endpoint desc
  usb: dwc3: ep0: Clear started flag on completion
  usb: dwc3: gadget: Clear started flag for non-IOC
  usb: dwc3: gadget: Fix logical condition
  USB: atm: ueagle-atm: add missing endpoint check
  USB: adutux: fix interface sanity check
  USB: idmouse: fix interface sanity checks
  USB: serial: io_edgeport: fix epic endpoint lookup
  usb: mon: Fix a deadlock in usbmon between mmap and read
  usb: common: usb-conn-gpio: Don't log an error on probe deferral
  usb: core: urb: fix URB structure initialization function
  usb: typec: fix use after free in typec_register_port()
  ...

Pull s390 updates from Vasily Gorbik:

 - Add support for KASAN_VMALLOC feature.

 - Remove the last user of problematic diag 0x44 call.

 - Adjust sampling interval and avoid sample data block overflow
   condition on pressure in perf code.

 - Prefer EOPNOTSUPP over ENOTSUPP and comments fixes.

* tag 's390-5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/kasan: add KASAN_VMALLOC support
  s390: remove last diag 0x44 caller
  s390/uv: use EOPNOTSUPP instead of ENOTSUPP
  s390/cpum_sf: Avoid SBD overflow condition in irq handler
  s390/cpum_sf: Adjust sampling interval to avoid hitting sample limits
  s390/test_unwind: fix spelling mistake "reqister" -> "register"
  s390/spinlock: remove confusing comment in arch_spin_lock_wait

Pull crypto fix from Herbert Xu:
 "Fix another build problem for Wireguard without Crypto"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: arm/curve25519 - add arch-specific key generation function

Pull cfis fixes from Steve French:
 "Three small smb3 fixes: this addresses two recent issues reported in
  additional testing during rc1, a refcount underflow and a problem with
  an intermittent crash in SMB2_open_init"

* tag '5.5-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Close cached root handle only if it has a lease
  SMB3: Fix crash in SMB2_open_init due to uninitialized field in compounding path
  smb3: fix refcount underflow warning on unmount when no directory leases

Pull overlayfs fixes from Miklos Szeredi:
 "Fix some bugs and documentation"

* tag 'ovl-fixes-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  docs: filesystems: overlayfs: Fix restview warnings
  docs: filesystems: overlayfs: Rename overlayfs.txt to .rst
  ovl: relax WARN_ON() on rename to self
  ovl: fix corner case of non-unique st_dev;st_ino
  ovl: don't use a temp buf for encoding real fh
  ovl: make sure that real fid is 32bit aligned in memory
  ovl: fix lookup failure on multi lower squashfs

For BINDER_TYPE_PTR and BINDER_TYPE_FDA transactions, the
num_valid local was calculated incorrectly causing the
range check in binder_validate_ptr() to miss out-of-bounds
offsets.

Fixes: bde4a19f ("binder: use userspace pointer as base of buffer space")
Signed-off-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191213202531.55010-1-tkjos@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull nios2 fix from Ley Foon Tan:
 "Fix nios2 ioremap regression"

* tag 'nios2-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: Fix ioremap

Pull Devicetree fixes from Rob Herring:

 - Fix for dependency tracking caused by unittest interaction

 - Fix some schema errors in Tegra memory controller schema

 - Update Maxime Ripard's email address

 - Review fixes to TI cpsw-switch

 - Add wakeup-source prop for STM32 rproc. Got dropped in the schema
   conversion.

* tag 'devicetree-fixes-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of/platform: Unconditionally pause/resume sync state during kernel init
  dt-bindings: memory-controllers: tegra: Fix type references
  dt-bindings: Change maintainer address
  dt-bindings: net: ti: cpsw-switch: update to fix comments
  dt-bindings: remoteproc: stm32: add wakeup-source property

Pull virtio fixes from Michael Tsirkin:
 "Some fixes and cleanup patches"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_balloon: divide/multiply instead of shifts
  virtio_balloon: name cleanups
  virtio-balloon: fix managed page counts when migrating pages between zones

Pull PCI fix from Bjorn Helgaas:
 "Fix rockchip outbound ATU issue that prevented Google Kevin
  Chromebooks from booting (Enric Balletbo i Serra)"

* tag 'pci-v5.5-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: rockchip: Fix IO outbound ATU register number

Pull i2c updates from Wolfram Sang:

 - removal of an old API where all in-kernel users have been converted
   as of this merge window.

 - a kdoc fix

 - a new helper that will make dependencies for the next API conversion
   a tad easier

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: add helper to check if a client has a driver attached
  i2c: fix header file kernel-doc warning
  i2c: remove i2c_new_dummy() API

Pull power management fixes from Rafael Wysocki:
 "These add PM QoS support to devfreq and fix a few issues in that
  subsystem, fix two cpuidle issues and do one minor cleanup in there,
  and address an ACPI power management problem related to devices with
  special power management requirements, like fans.

  Specifics:

   - Add PM QoS support, based on the frequency QoS introduced during
     the 5.4 cycle, to devfreq (Leonard Crestez).

   - Fix some assorted devfreq issues (Leonard Crestez).

   - Fix an unintentional cpuidle behavior change (introduced during the
     5.4 cycle) related to the active polling time limit (Marcelo
     Tosatti).

   - Fix a recently introduced cpuidle helper function and do a minor
     cleanup in the cpuidle core (Rafael Wysocki).

   - Avoid adding devices with special power management requirements,
     like fans, to the generic ACPI PM domain (Rafael Wysocki)"

* tag 'pm-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: Drop unnecessary type cast in cpuidle_poll_time()
  cpuidle: Fix cpuidle_driver_state_disabled()
  ACPI: PM: Avoid attaching ACPI PM domain to certain devices
  cpuidle: use first valid target residency as poll time
  PM / devfreq: Use PM QoS for sysfs min/max_freq
  PM / devfreq: Add PM QoS support
  PM / devfreq: Don't fail devfreq_dev_release if not in list
  PM / devfreq: Introduce get_freq_range helper
  PM / devfreq: Set scaling_max_freq to max on OPP notifier error
  PM / devfreq: Fix devfreq_notifier_call returning errno

Pull sound fixes from Takashi Iwai:
 "A small collection of fixes.

  The main changes are fixes for a couple of regressions in AMD HD-audio
  and FireWire that were introduced in 5.5-rc1. The rest are small fixes
  for echoaudio and FireWire, as well as a usual Dell HD-audio fixup"

* tag 'sound-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Line-out jack doesn't work on a Dell AIO
  ALSA: hda/hdmi - Fix duplicate unref of pci_dev
  ALSA: fireface: fix return value in error path of isochronous resources reservation
  ALSA: oxfw: fix return value in error path of isochronous resources reservation
  ALSA: firewire-motu: fix double unlocked 'motu->mutex'
  ALSA: echoaudio: simplify get_audio_levels

Pull drm fixes from Dave Airlie:
 "Usual round of rc2 fixes.

  i915 and amdgpu leading the charge, but a few others in here,
  including some nouveau fixes, all seems pretty for rc2, but hey it's a
  Fri 13th pull so I'm sure it'll cause untold bad fortune.

  dma-buf:
   - memory leak fix
   - expand MAINTAINERS scope

  core:
   - fix mode matching for drivers not using picture_aspect_ratio

  nouveau:
   - panel scaling fix
   - MST BPC fix
   - atomic fixes

  i915:
   - GPU hang on idle transition
   - GLK+ FBC corruption fix
   - non-priv OA access on Tigerlake
   - HDCP state fix
   - CI found race fixes

  amdgpu:
   - renoir DC fixes
   - GFX8 fence flush alignment with userspace
   - Arcturus power profile fix
   - DC aux + i2c over aux fixes
   - GPUVM invalidation semaphore fixes
   - gfx10 golden registers update

  mgag200:
   - expand startadd fix

  panfrost:
   - devfreq fix
   - memory fixes

  mcde:
   - DSI pointer deref fix"

* tag 'drm-fixes-2019-12-13' of git://anongit.freedesktop.org/drm/drm: (51 commits)
  drm/amdgpu: add invalidate semaphore limit for SRIOV in gmc10
  drm/amdgpu: add invalidate semaphore limit for SRIOV and picasso in gmc9
  drm/amdgpu: avoid using invalidate semaphore for picasso
  Revert "drm/amdgpu: dont schedule jobs while in reset"
  drm/amdgpu: fix license on Kconfig and Makefiles
  drm/amdgpu/gfx10: update gfx golden settings for navi14
  drm/amdgpu/gfx10: update gfx golden settings
  drm/amdgpu/gfx10: update gfx golden settings for navi14
  drm/amdgpu/gfx10: update gfx golden settings
  drm/i915: Serialise with remote retirement
  drm/amd/display: include linux/slab.h where needed
  drm/amd/display: fix undefined struct member reference
  drm/nouveau/kms/nv50-: fix panel scaling
  drm/nouveau/kms/nv50-: Limit MST BPC to 8
  drm/nouveau/kms/nv50-: Store the bpc we're using in nv50_head_atom
  drm/nouveau/kms/nv50-: Call outp_atomic_check_view() before handling PBN
  drm/nouveau: Fix drm-core using atomic code-paths on pre-nv50 hardware
  drm/nouveau: Move the declaration of struct nouveau_conn_atom up a bit
  drm/i915/gt: Detect if we miss WaIdleLiteRestore
  drm/i915/hdcp: Nuke intel_hdcp_transcoder_config()
  ...

Pull block fixes from Jens Axboe:

 - stable fix for the bi_size overflow. Not a corruption issue, but a
   case wher we could merge but disallowed (Andreas)

 - NVMe pull request via Keith, with various fixes.

 - MD pull request from Song.

 - Merge window regression fix for the rq passthrough stats (Logan)

 - Remove unused blkcg_drain_queue() function (Guoqing)

* tag 'for-linus-20191212' of git://git.kernel.dk/linux-block:
  blk-cgroup: remove blkcg_drain_queue
  block: fix NULL pointer dereference in account statistics with IDE
  md: make sure desc_nr less than MD_SB_DISKS
  md: raid1: check rdev before reference in raid1_sync_request func
  raid5: need to set STRIPE_HANDLE for batch head
  block: fix "check bi_size overflow before merge"
  nvme/pci: Fix read queue count
  nvme/pci Limit write queue sizes to possible cpus
  nvme/pci: Fix write and poll queue types
  nvme/pci: Remove last_cq_head
  nvme: Namepace identification descriptor list is optional
  nvme-fc: fix double-free scenarios on hw queues
  nvme: else following return is not needed
  nvme: add error message on mismatching controller ids
  nvme_fc: add module to ops template to allow module references
  nvmet-loop: Avoid preallocating big SGL for data
  nvme-fc: Avoid preallocating big SGL for data
  nvme-rdma: Avoid preallocating big SGL for data

Pull io_uring fixes from Jens Axboe:

 - A tweak to IOSQE_IO_LINK (also marked for stable) to allow links that
   don't sever if the result is < 0.

   This is mostly for linked timeouts, where if we ask for a pure
   timeout we always get -ETIME. This makes links useless for that case,
   hence allow a case where it works.

 - Five minor optimizations to fix and improve cases that regressed
   since v5.4.

 - An SQTHREAD locking fix.

 - A sendmsg/recvmsg iov assignment fix.

 - Net fix where read_iter/write_iter don't honor IOCB_NOWAIT, and
   subsequently ensuring that works for io_uring.

 - Fix a case where for an invalid opcode we might return -EBADF instead
   of -EINVAL, if the ->fd of that sqe was set to an invalid fd value.

* tag 'io_uring-5.5-20191212' of git://git.kernel.dk/linux-block:
  io_uring: ensure we return -EINVAL on unknown opcode
  io_uring: add sockets to list of files that support non-blocking issue
  net: make socket read/write_iter() honor IOCB_NOWAIT
  io_uring: only hash regular files for async work execution
  io_uring: run next sqe inline if possible
  io_uring: don't dynamically allocate poll data
  io_uring: deferred send/recvmsg should assign iov
  io_uring: sqthread should grab ctx->uring_lock for submissions
  io-wq: briefly spin for new work after finishing work
  io-wq: remove worker->wait waitqueue
  io_uring: allow unbreakable links

Merge tag 'for-5.5/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix DM multipath by restoring full path selector functionality for
   bio-based configurations that don't haave a SCSI device handler.

 - Fix dm-btree removal to ensure non-root btree nodes have at least
   (max_entries / 3) entries. This resolves userspace thin_check
   utility's report of "too few entries in btree_node".

 - Fix both the DM thin-provisioning and dm-clone targets to properly
   flush the data device prior to metadata commit. This resolves the
   potential for inconsistency across a power loss event when the data
   device has a volatile writeback cache.

 - Small documentation fixes to dm-clone and dm-integrity.

* tag 'for-5.5/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  docs: dm-integrity: remove reference to ARC4
  dm thin: Flush data device before committing metadata
  dm thin metadata: Add support for a pre-commit callback
  dm clone: Flush destination device before committing metadata
  dm clone metadata: Use a two phase commit
  dm clone metadata: Track exact changes per transaction
  dm btree: increase rebalance threshold in __rebalance2()
  dm: add dm-clone to the documentation index
  dm mpath: remove harmful bio-based optimization