- 02 Aug, 2018 31 commits
-
-
Quinn Tran authored
After selecting the NPort handle/loop_id, set a bit in the loop_id_map to prevent others from selecting the same NPort handle. Signed-off-by:
Quinn Tran <quinn.tran@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Quinn Tran authored
Flush pending mailbox commands on chip reset. Wake up command that's waiting for an interrupt and wait for mailbox counters to go to zero. Signed-off-by:
-
Quinn Tran authored
During normal IO, FW can return IO with 'port unavailble' status. Driver would send a LOGO to remote port for session resync. On an off chance, a PLOGI could arrive before sending the LOGO. This patch will skip sendiing LOGO if a PLOGI just came in. Signed-off-by:
-
Quinn Tran authored
This patch sets discovery state back to GNL (Get Name List) when session is stuck at GPDB (Get Port DataBase). This will allow state machine to retry login and move session state ahead in discovery. Signed-off-by:
-
Quinn Tran authored
Prevent multiple registrations with transport layer for the same remote port. Signed-off-by:
-
Quinn Tran authored
Driver uses shadow pointer instead of Mirror pointer for firmware dump collection. Skip those entries for Mirror pointers for Request/Response queue from firmware dump template reading. Following messages are printed in log messages: qla27xx_fwdt_entry_t268: unknown buffer 4 qla27xx_fwdt_entry_t268: unknown buffer 5 This patch fixes these error messages by adding skip_entry() to not read them from template. Signed-off-by:
-
Quinn Tran authored
Prevent user from sending commands through sysfs while firmware is not running or reset is in progress. Signed-off-by:
-
Quinn Tran authored
qla2x00_reset_active only covers the window of turning the chip off. Add check to cover turning chip on. Signed-off-by:
-
Quinn Tran authored
Login retry count was not properly decrementing which lead to endless retry. Signed-off-by:
-
Quinn Tran authored
In case of N2N connect, sg_reset for bus/device/host was causing driver and firmware state to go out of sync. This patch fixes this link instablity when reconnect is attempted after link flap. Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Colin Ian King authored
Variables scriptb0 and dp_sgmin are being assigned but are never used hence they are redundant and can be removed. Cleans up clang warnings: warning: variable 'scriptb0' set but not used [-Wunused-but-set-variable] warning: variable 'dp_sgmin' set but not used [-Wunused-but-set-variable] Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Arjun Vynipadath authored
- Updates csio_get_flash_params() to take care of ISSI, Macronix and Winbond FLASH parts. - Assume flash part size to be 4MB if it cannot be identified Signed-off-by:
Arjun Vynipadath <arjun@chelsio.com> Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Bart Van Assche authored
A long time ago the unfortunate decision was taken to add a self-deletion attribute to the sysfs SCSI device directory. That decision was unfortunate because self-deletion is really tricky. We can't drop that attribute because widely used user space software depends on it, namely the rescan-scsi-bus.sh script. Hence this patch that avoids that writing into that attribute triggers a deadlock. See also commit 7973cbd9 ("[PATCH] add sysfs attributes to scan and delete scsi_devices"). This patch avoids that self-removal triggers the following deadlock: ====================================================== WARNING: possible circular locking dependency detected 4.18.0-rc2-dbg+ #5 Not tainted ------------------------------------------------------ modprobe/6539 is trying to acquire lock: 000000008323c4cd (kn->count#202){++++}, at: kernfs_remove_by_name_ns+0x45/0x90 but task is already holding lock: 00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&shost->scan_mutex){+.+.}: __mutex_lock+0xfe/0xc70 mutex_lock_nested+0x1b/0x20 scsi_remove_device+0x26/0x40 [scsi_mod] sdev_store_delete+0x27/0x30 [scsi_mod] dev_attr_store+0x3e/0x50 sysfs_kf_write+0x87/0xa0 kernfs_fop_write+0x190/0x230 __vfs_write+0xd2/0x3b0 vfs_write+0x101/0x270 ksys_write+0xab/0x120 __x64_sys_write+0x43/0x50 do_syscall_64+0x77/0x230 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #0 (kn->count#202){++++}: lock_acquire+0xd2/0x260 __kernfs_remove+0x424/0x4a0 kernfs_remove_by_name_ns+0x45/0x90 remove_files.isra.1+0x3a/0x90 sysfs_remove_group+0x5c/0xc0 sysfs_remove_groups+0x39/0x60 device_remove_attrs+0x82/0xb0 device_del+0x251/0x580 __scsi_remove_device+0x19f/0x1d0 [scsi_mod] scsi_forget_host+0x37/0xb0 [scsi_mod] scsi_remove_host+0x9b/0x150 [scsi_mod] sdebug_driver_remove+0x4b/0x150 [scsi_debug] device_release_driver_internal+0x241/0x360 device_release_driver+0x12/0x20 bus_remove_device+0x1bc/0x290 device_del+0x259/0x580 device_unregister+0x1a/0x70 sdebug_remove_adapter+0x8b/0xf0 [scsi_debug] scsi_debug_exit+0x76/0xe8 [scsi_debug] __x64_sys_delete_module+0x1c1/0x280 do_syscall_64+0x77/0x230 entry_SYSCALL_64_after_hwframe+0x49/0xbe other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&shost->scan_mutex); lock(kn->count#202); lock(&shost->scan_mutex); lock(kn->count#202); *** DEADLOCK *** 2 locks held by modprobe/6539: #0: 00000000efaf9298 (&dev->mutex){....}, at: device_release_driver_internal+0x68/0x360 #1: 00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod] stack backtrace: CPU: 10 PID: 6539 Comm: modprobe Not tainted 4.18.0-rc2-dbg+ #5 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014 Call Trace: dump_stack+0xa4/0xf5 print_circular_bug.isra.34+0x213/0x221 __lock_acquire+0x1a7e/0x1b50 lock_acquire+0xd2/0x260 __kernfs_remove+0x424/0x4a0 kernfs_remove_by_name_ns+0x45/0x90 remove_files.isra.1+0x3a/0x90 sysfs_remove_group+0x5c/0xc0 sysfs_remove_groups+0x39/0x60 device_remove_attrs+0x82/0xb0 device_del+0x251/0x580 __scsi_remove_device+0x19f/0x1d0 [scsi_mod] scsi_forget_host+0x37/0xb0 [scsi_mod] scsi_remove_host+0x9b/0x150 [scsi_mod] sdebug_driver_remove+0x4b/0x150 [scsi_debug] device_release_driver_internal+0x241/0x360 device_release_driver+0x12/0x20 bus_remove_device+0x1bc/0x290 device_del+0x259/0x580 device_unregister+0x1a/0x70 sdebug_remove_adapter+0x8b/0xf0 [scsi_debug] scsi_debug_exit+0x76/0xe8 [scsi_debug] __x64_sys_delete_module+0x1c1/0x280 do_syscall_64+0x77/0x230 entry_SYSCALL_64_after_hwframe+0x49/0xbe See also https://www.mail-archive.com/linux-scsi@vger.kernel.org/msg54525.html. Fixes: ac0ece91 ("scsi: use device_remove_file_self() instead of device_schedule_callback()") Signed-off-by:
Bart Van Assche <bart.vanassche@wdc.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Tejun Heo <tj@kernel.org> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Bart Van Assche authored
Introduce these two functions and export them such that the next patch can add calls to these functions from the SCSI core. Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
James Smart authored
Update the driver version to 12.0.0.6 Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
James Smart authored
Enablement of the PBDE optimization brought out some incompatible behaviors under error scenarios. Best to disable and remove the PBDE optimization. Signed-off-by:
-
James Smart authored
After memory allocation for the LCB response frame, the memory wasn't zero initialized, and not all fields are set. Thus garbage shows up in the payload. Fix by zeroing the memory at allocation. Also properly set the Capability field based on duration support. Signed-off-by:
-
James Smart authored
Performance is affected when target queue depth is tracked. An atomic counter is incremented on the submission path which competes with it being decremented on the completion path. In addition, multiple CPUs can simultaniously be manipulating this counter for the same ndlp. Reduce the overhead by only performing the target increment/decrement when the target queue depth is less than the overall adapter depth, thus is actually meaningful. Signed-off-by:
-
James Smart authored
During remote port loss fault testing, the driver crashed with the following trace: general protection fault: 0000 [#1] SMP RIP: ... lpfc_nvme_register_port+0x250/0x480 [lpfc] Call Trace: lpfc_nlp_state_cleanup+0x1b3/0x7a0 [lpfc] lpfc_nlp_set_state+0xa6/0x1d0 [lpfc] lpfc_cmpl_prli_prli_issue+0x213/0x440 lpfc_disc_state_machine+0x7e/0x1e0 [lpfc] lpfc_cmpl_els_prli+0x18a/0x200 [lpfc] lpfc_sli_sp_handle_rspiocb+0x3b5/0x6f0 [lpfc] lpfc_sli_handle_slow_ring_event_s4+0x161/0x240 [lpfc] lpfc_work_done+0x948/0x14c0 [lpfc] lpfc_do_work+0x16f/0x180 [lpfc] kthread+0xc9/0xe0 ret_from_fork+0x55/0x80 After registering a new remoteport, the driver is pulling an ndlp pointer from the lpfc rport associated with the private area of a newly registered remoteport. The private area is uninitialized, so it's garbage. Correct by pulling the the lpfc rport pointer from the entering ndlp point, then ndlp value from at rport. Note the entering ndlp may be replacing by the rport->ndlp due to an address change swap. Signed-off-by:
-
James Smart authored
Enabling list_debug showed the drivers txcmplq was suffering list corruption. The systems will eventually crash because the iocb free list gets crossed linked with the prings txcmplq. Most systems will run for a while after the corruption, but will eventually crash when a scsi eh reset occurs and the txcmplq is attempted to be flushed. The flush gets stuck in an endless loop. The problem is the abort handler does not hold the sli4 ring lock while validating the IO so the IO could complete while the driver is still preping the abort. The erroneously generated abort, when it completes, has pointers to the original IO that has already completed, and the IO manipulation (for the second time) corrupts the list. Correct by taking the ring lock early in the abort handler so the erroneous abort won't be sent if the io has/is completing. Signed-off-by:
-
James Smart authored
CNA ports were showing speed as "unknown" even if the link is up. Add speed decoding for FCOE-based adapters. Signed-off-by:
-
James Smart authored
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI combination. For ELS aborts, driver specifies IOTAG correctly but RPI is not specified. Fix by setting RPI in WQE. Signed-off-by:
-
Mike Christie authored
This converts drivers that were only calling transport_deregister_session to use target_remove_session. The calling of transport_deregister_session_configfs via target_remove_session for these types of drivers is ok, because they were not exporting info from fields like sess_acl_list, sess->se_tpg and sess->fabric_sess_ptr from configfs accessible functions, so they will see no difference. Signed-off-by:
Mike Christie <mchristi@redhat.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Cc: Felipe Balbi <balbi@kernel.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Juergen Gross <jgross@suse.com> Signed-off-by:
-
Mike Christie authored
This converts tcm_fc to use target_remove_session tcm_fc was calling transport_deregister_session_configfs then calling transport_deregister_session when commands have completed. It should be ok for it to call transport_deregister_session_configfs later via target_remove_session because transport_deregister_session_configfs only prevents access from configfs via tpg removal and its call to the close_session callback for that driver, and this is already protected by the ft_lport_lock and its port lookup handling. Signed-off-by:
-
Mike Christie authored
This converts the drivers that called transport_deregister_session_configfs and then immediately called transport_deregister_session to use target_remove_session. Signed-off-by:
-
Mike Christie authored
This adds a function to remove a session which should be used by drivers that use target_setup_session. The next patches will convert the target drivers to use this new function. Signed-off-by:
-
Mike Christie authored
Rename target_alloc_session to target_setup_session to avoid confusion with the other transport session allocation function that only allocates the session and because the target_alloc_session does so much more. It allocates the session, sets up the nacl and registers the session. The next patch will then add a remove function to match the setup in this one, so it should make sense for all drivers, except iscsi, to just call those 2 functions to setup and remove a session. iscsi will continue to be the odd driver. Signed-off-by:
-
Mike Christie authored
transport_init_session_tags is only called from target_core_transport.c so make it static. Signed-off-by:
-
Mike Christie authored
Just have iscsit_start_nopin_timer grab the lock and call __iscsit_start_nopin_timer. Signed-off-by:
-
Mike Christie authored
When __transport_register_session is called from transport_register_session irqs will already have been disabled, so we do not want the unlock irq call to enable them until the higher level has done the final spin_unlock_irqrestore/ spin_unlock_irq. This has __transport_register_session use the save/restore call. Signed-off-by:
-
- 31 Jul, 2018 9 commits
-
-
Bart Van Assche authored
The cxgbit driver expects that __iscsit_free_cmd() is called before the target core frees the command page list. Since this patch breaks the cxgbit driver, revert it. Reported-by:
-
Mike Christie authored
We use unsigned long, size_t and u64 for dev_size. This has us standardize on u64. Signed-off-by:
Xiubo Li <xiubli@redhat.com> Signed-off-by:
-
Mike Christie authored
Instead of doing strdup and kstrto* just use match_int for dev params. It will be ok to use int instead of unsigned long in tcmu_set_dev_attrib because that is only being used for max sectors and block size and the supported values for them are well under the max possible integer value. Signed-off-by:
-
Mike Christie authored
This patch prevents a bug where data_bitmap is allocated in tcmu_configure_device, userspace changes the max_blocks setting, the device is mapped to a LUN, then we try to access the data_bitmap based on the new max_blocks limit which may now be out of range. To prevent this, we just check if data_bitmap has been setup. If it has then we fail the max_blocks update operation. Signed-off-by:
-
Mike Christie authored
The tcmu dev is added to the list of tcmu devices during configuration. At this time the tcmu setup has completed, but lio core has not completed its setup. The device is not yet usable so do not try to unmap blocks from it Signed-off-by:
-
Mike Christie authored
Do not allow userspace to block or reset the ring until the device has been configured. This will prevent the bug where userspace can write to those files and access mb_addr before it has been setup. Signed-off-by:
-
Mike Christie authored
Use the lio core helper to check if the device is configured. Signed-off-by:
-
Mike Christie authored
This just adds a helper function to check if a device is configured and it converts the target users to use it. The next patch will add a backend module user so those types of modules do not have to know the lio core details. Signed-off-by:
-
Mike Christie authored
Use INIT_LIST_HEAD to initialize node list head. Signed-off-by:
-
