- 20 Apr, 2010 11 commits
-
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
AR9300 based hardware can 3x3 MCS rates, this should be set in the HT capabilities. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Instead of increasing bits_per_symbol for supporting more streams, keep it single-stream only and multiply the values by the numer of streams. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Include MCS0-31 and also add SGI for HT20. This makes it possible to support more different rate combinations with newer hardware. Based on a patch by Selvam. T. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Holger Schurig authored
This adds the first element of survey data, the noise floor figure. Signed-off-by: Holger Schurig <holgerschurig@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Holger Schurig authored
This adds the survey function to both mac80211 itself and to mac80211_hwsim. For the latter driver, we simply invent some noise level.A real driver which cannot determine the real channel noise MUST NOT report any noise, especially not a magically conjured one :-) Signed-off-by: Holger Schurig <holgerschurig@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Daniel Yingqiang Ma authored
When I set up multiple VAPs with ath9k, I encountered an issue that the traffic may be lost after a while. The detailed phenomenon is 1. After a while the clients connected to one of these VAPs will get into a state that no broadcast/multicast packets can be transfered successfully while the unicast packets can be transfered normally. 2. Minutes latter the unitcast packets transfer will fail as well, because the ARP entry is expired and it can't be freshed due to the broadcast trouble. It's caused by the group key overwritten and someone discussed this issue in ath9k-devel maillist before, but haven't work out a fix yet. I referred the method in madwifi, and made a patch for ath9k. The method is to set the high bit of the sender(AP)'s address, and associated that mac and the group key. It requires the hardware supports multicast frame key search. It seems true for AR9160. Not sure whether it's the correct way to fix this issue. But it seems to work in my test. The patch is attached, feel free to revise it. Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 19 Apr, 2010 9 commits
-
-
Xose Vazquez Perez authored
Applied common sense, no info from the manufacturer: (0x8516, 0x2070) is RT2070 (0x8516, 0x2770) is RT2770 (0x8516, 0x2870) is RT2870 [...] Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
One HT debugging printk is missing a newline, add it. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
David Kilroy authored
Orinoco should be endian clean, so enable the checking. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
David Kilroy authored
Instead of using a local function. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
David Kilroy authored
... to set fragmentation and RTS thresholds. Also report RTS retry settings during wiphy init. Note that the existing semantics for enabling microwave robustness are preserved on firmwares that have it. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
The sta_cleanup timer is used to periodically expire buffered frames from the tx buf. The timer is executing periodically, regardless of the need for it. This is wasting resources. Fix this simply by not restarting the sta_cleanup timer if the tx buffer was empty. Restart the timer when there is some more tx-traffic. Cc: Janne Ylälehto <janne.ylalehto@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Kalle reported that his system deadlocks since my recent work in this area. The reason quickly became apparent: we try to cancel_timer_sync() a timer from within itself. Fix that by making the function aware of the context it is called from. Reported-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Daniel Halperin authored
The flag is called IEEE80211_TX_STAT_AMPDU rather than using the whole word STATUS. Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
-
- 16 Apr, 2010 20 commits
-
-
Johannes Berg authored
Some future hardware will also require some antenna overrides so make the current logic more generic; right now it is semantically based on a workaround for off-channel reception but the reasons for the new antenna overrides will be different. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
Off-channel reception is acceptable in monitor mode, and checking for monitor mode this way is not really correct anyway since it could be the case while operating. Now iwl_is_monitor_mode() is no longer used so remove it completely. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
Monitor mode operation need not (and probably should not) affect scanning this way since real monitoring can not properly happen while scanning anyway. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
The flag name is a little misleading, this flag instructs the device to ignore bluetooth messages for purposes of frame transmissions, so rename the flag to TX_CMD_FLG_IGNORE_BT. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
Some future hardware will require a different command to be sent for bluetooth coexist, so make this a virtual method that can be changed on a per-device basis. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Wey-Yi Guy authored
Since multiple new devices having similar uCode architecture and use same registers address, remove more reference to 5000 series to eliminate the confusion. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Wey-Yi Guy authored
Perform sanity check for turn on aggregation tid. Also remove the option for turn on all the aggregation tids at once since it is deprecated function and not being used. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Wey-Yi Guy authored
For 6000g2 series of NICs, PA type is determined by uCode, driver do not have to set the register for internal/external PA. It is a workaround just for 6000 series NICs. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Wey-Yi Guy authored
Add hardware revision for 6000g2 series of NIC Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Shanyu Zhao authored
This function is called twice in a row, remove the second one. Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Abhijeet Kolekar authored
Seperate debugfs functions into iwlagn specific debugfs file and Add debugfs ops to iwlwifi. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Wey-Yi Guy authored
Use the show uCode statistics function for uCode debugging purposes only; it is being duplicated in both debugfs and sysfs. remove the one from sysfs. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Shanyu Zhao authored
This patch is to bring up 6000 Series 2x2 AGN Gen2 adapters. Seperate various version numbers from 6000 Series definitions; Add module firmware declaration for the new adapters; Add additional device IDs and subsystem IDs; Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Wey-Yi Guy authored
Some definition for eeprom apply to more than 5000 series device, change the name to reflect it for easy reading. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
Scan requesting doesn't need to be asynchronous since all code paths leading up to it can sleep. Make the scan request a new util operation that is hw-specific (to account for 3945 vs. agn) and call it right in place. This patch moves a lot of code into iwlagn as it need not be in iwlcore. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
I keep checking what "priv->scan" is, so rename it to "priv->scan_cmd" which more clearly tells us what it is. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
Since we no longer do a multi-pass scan, keeping track of how long each pass took is pointless since there will only be one. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
This logic is just confusing, if anything it belongs into mac80211. Also, even if we do scan during the EAPOL handshake, that will not cause any problems, just a short delay. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
With atomic bitops, test_and_{set,clear}_bit should be used instead of separate test_bit and set_bit/clear_bit. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-
Johannes Berg authored
Since mac80211 will now never request scanning multiple bands, we can remove all the associated logic and scan a single band only in each scan. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
-