snd_soc_dai_link_event() is updating snd_soc_dai :: active,
but it is unbalance.
It counts up if it has startup callback.

	case SND_SOC_DAPM_PRE_PMU:
		...
		snd_soc_dapm_widget_for_each_source_path(w, path) {
			...
			if (source->driver->ops->startup) {
				...
=>				source->active++;
			}
			...
		}
		...

But, always counts down

	case SND_SOC_DAPM_PRE_PMD:
		...
		snd_soc_dapm_widget_for_each_source_path(w, path) {
			...
=>			source->active--;
			...
		}

This patch always counts up when SND_SOC_DAPM_PRE_PMD.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add regcache_mark_dirty before regcache_sync for power
of codec may be lost at suspend, then all the register
need to be reconfigured.

Fixes: 0c516b4f ("ASoC: cs42xx8: Add codec driver
support for CS42448/CS42888")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When the output sample rate is [8kHz, 30kHz], the limitation
of the supported ratio range is [1/24, 8]. In the driver
we use (8kHz, 30kHz) instead of [8kHz, 30kHz].
So this patch is to fix this issue and the potential rounding
issue with divider.

Fixes: fff6e03c ("ASoC: fsl_asrc: add support for 8-30kHz
output sample rate")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

snd_soc_component_update_bits() may return 1 if operation
was successful and the value of the register changed.
Return a non-zero in ak4458_rstn_control for an error only.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

If playback/capture is paused and system enters S3, after system returns
from suspend, BE dai needs to call prepare() callback when playback/capture
is released from pause if RESUME_INFO flag is not set.

Currently, the dpcm_be_dai_prepare() function will block calling prepare()
if the pcm is in SND_SOC_DPCM_STATE_PAUSED state. This will cause the
following test case fail if the pcm uses BE:

playback -> pause -> S3 suspend -> S3 resume -> pause release

The playback may exit abnormally when pause is released because the BE dai
prepare() is not called.

This patch allows dpcm_be_dai_prepare() to call dai prepare() callback in
SND_SOC_DPCM_STATE_PAUSED state.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

AK4458 is probed successfully even if AK4458 is not present - this
is caused by probe function returning no error on i2c access failure.
Return an error on probe if i2c access has failed.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The cs4265_readable_register function stopped short of the maximum
register.

An example bug is taken from :
https://github.com/Audio-Injector/Ultra/issues/25

Where alsactl store fails with :
Cannot read control '2,0,0,C Data Buffer,0': Input/output error

This patch fixes the bug by setting the cs4265 to have readable
registers up to the maximum hardware register CS4265_MAX_REGISTER.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Remove the erroneous addition of "SET_VALUE" to the GLB
IPC command string.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

A race condition exists in handling firmware boot timeout.
If FW sends FW_READY just after boot timeout has expired in
driver, a kernel exception will result as FW_READY handler
will be run while the state is still being cleaned up in
snd_sof_run_firmware(). Avoid the race by setting
boot_complete also in the error case.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The nocodec option can be selected individually, leading to the following
issue:

sound/soc/sof/core.o: In function `snd_sof_device_probe':
core.c:(.text+0x4af): undefined reference to `sof_nocodec_setup'

Fix by selecting the SND_SOF_NOCODEC option as needed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The recent fix for the build fix caused a couple of unused variable
compiler warnings when CONFIG_SND_SOC_SOF_NOCODEC isn't set:
  sound/soc/sof/core.c:263:6: warning: unused variable ‘ret’ [-Wunused-variable]
  sound/soc/sof/core.c:262:28: warning: unused variable ‘machine’ [-Wunused-variable]

Fix them by adding another ifdef.

Fixes: ce38a750 ("ASoC: SOF: core: fix undefined nocodec reference")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

- Set period minimum size. Ensure at least 5ms period
up to 48kHz/16 bits to prevent underrun/overrun.
- Remove MDMA constraints on period maximum size and
set period maximum to half the buffer maximum size.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some userspace apps, like pulseaudio, may call open, hw_params,
prepare to judge whether the pcm is ready or not. Current hdac_hdmi
will return -ENODEV if monitor is not connected, which will cause
the apps believe the pcm is not ready. Actually PCM for hdmi is ready,
even the monitor is not connected.

This patch removes the check of monitor presence in hw_params, just like
what the legacy HD-Audio driver does.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

mt6358_amic_disable() resets PGA to 0.

Save the gain settings from mixer control and restore them when using
the microphone.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Output volume settings from mixer controls would be lost.

Imagine that "Headphone Volume" has set to -10dB via amixer:
- in mtk_hp_enable()
  - hp_store_gain() saves the volume setting -10dB from regmap_read()
    to ana_gain[AUDIO_ANALOG_VOLUME_HPOUTL]
  - headset_volume_ramp() ramps up from -10dB to -10dB
- in mtk_hp_disable()
  - headset_volume_ramp() ramps down from -10dB to -40dB

Next time in mtk_hp_enable(), hp_store_gain() would save -40dB but
not -10dB.  As a result, headset_volume_ramp() would ramp from -10dB to
-40dB (which is mute).
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Mt6358 ramps up from the smallest volume (i.e. -10dB) to target dB when
opening and ramps down from target dB to mute (i.e. -40dB) when closing.
If target is equal to -10dB when opening, headset_volume_ramp() simply
leaves current setting (which may not be -10dB) unchanged.

Execute the loop at least once to initialize the setting to the
starting point (i.e. from).
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The existing code mistakenly uses IS_ENABLED in C code instead of as
in conditional compilation, leading to the following error:

ld: sound/soc/sof/core.o: in function `sof_machine_check':
sound/soc/sof/core.c:279: undefined reference to `sof_nocodec_setup'

Fix by using #if !IS_ENABLED()
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The SND_SOC_INTEL_COMMON Kconfig was removed months ago from SOF
Kconfig files but is still selected instead of the correct
SND_SOC_SOF_INTEL_COMMON kconfig which does select xtensa stuff,
leading to the following errors.

ld: sound/soc/sof/sof-acpi-dev.o:(.rodata+0x120): undefined reference
to `sof_xtensa_arch_ops'
ld: sound/soc/sof/sof-acpi-dev.o:(.rodata+0x180): undefined reference
to `sof_xtensa_arch_ops'
ld: sound/soc/sof/sof-acpi-dev.o:(.rodata+0x1e0): undefined reference
to `sof_xtensa_arch_ops'
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This fixes a compile warning below by properly handling the error code
from sof_get_ctrl_copy_params():
  include/linux/kernel.h:843:43: warning: 'sparams.pl_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
  sound/soc/sof/ipc.c:639:34: note: 'sparams.pl_size' was declared here

The function returns an error before setting sparams.pl_size, so it'd
assign an uninitialized value at a later point.

Fixes: 53e0c72d ("ASoC: SOF: Add support for IPC IO between DSP and Host")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Paper over a trivial case leading to an uninitialized variable compile
warning:
  sound/soc/rockchip/rockchip_pdm.c:179:3: warning: ‘clk_out’ may be used uninitialized in this function [-Wmaybe-uninitialized]

Fixes: 624e8e00 ("ASoC: rockchip: pdm: fixup pdm fractional div")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

A trivial fix for the randconfig build error:
  sound/soc/sof/ops.c:20:6: warning: ‘ret’ is used uninitialized in this function [-Wuninitialized]

Fixes: d1d95fcb ("ASoC: SOF: Add DSP HW abstraction operations")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

A trivial fix for the randconfig build error:
  sound/soc/codecs/da7219.c:2366:6: warning: unused variable ‘i’ [-Wunused-variable]

Fixes: d90ba6c8 ("ASoC: da7219: Expose BCLK and WCLK control through CCF")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix kconfig warning for unmet dependency for IOSF_MBI when
PCI is not set/enabled.  Fixes this warning:

WARNING: unmet direct dependencies detected for IOSF_MBI
  Depends on [n]: PCI [=n]
  Selected by [y]:
  - SND_SOC_SOF_ACPI [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && SND_SOC_SOF_TOPLEVEL [=y] && (ACPI [=y] || COMPILE_TEST [=n]) && X86 [=y]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: alsa-devel@alsa-project.org
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Change trace level to debug to avoid spurious messages.
Return quietly when accessing iec958 control, while no
S/PDIF signal is available.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

- Set period minimum size. Ensure at least 5ms period
up to 48kHz/16 bits to prevent underrun/overrun.
- Remove MDMA constraints on period maximum size and
set period maximum to half the buffer maximum size.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The max98090 driver defines 3 DAPM muxes; one for the right line output
(LINMOD Mux), one for the left headphone mixer source (MIXHPLSEL Mux)
and one for the right headphone mixer source (MIXHPRSEL Mux). The same
bit is used for the mux as well as the DAPM enable, and although the mux
can be correctly configured, after playback has completed, the mux will
be reset during the disable phase. This is preventing the state of these
muxes from being saved and restored correctly on system reboot. Fix this
by marking these muxes as SND_SOC_NOPM.

Note this has been verified this on the Tegra124 Nyan Big which features
the MAX98090 codec.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

The current algorithm allows 3 types of transfers, 16bit, 32bit and
burst. According to Realtek, 16bit transfers have a special restriction
in that it is restricted to the memory region of
0x18020000 ~ 0x18021000. This region is the memory location of the I2C
registers. The current algorithm does not uphold this restriction and
therefore fails to complete writes.

Since this has been broken for some time it likely no one is using it.
Better to simply disable the 16 bit writes. This will allow users to
properly load firmware over SPI without data corruption.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

For Spreadtrum audio platform driver, it need allocate a larger DMA buffer
dynamically to copy audio data between userspace and kernel space, but that
will increase the risk of memory allocation failure especially the system
is under heavy load situation.

To make sure the audio can work in this scenario, we usually reserve one
region of memory to be used as a shared pool of DMA buffers for the
platform component. So add of_reserved_mem_device_init_by_idx() function
to initialize the shared pool of DMA buffers to be used by the platform
component.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

On kbl_rt5663_max98927, commit 38a5882e
    ("ASoC: Intel: kbl_rt5663_max98927: Map BTN_0 to KEY_PLAYPAUSE")
    This key pair mapping to play/pause when playing Youtube

The Android 3.5mm Headset jack specification mentions that BTN_0 should
be mapped to KEY_MEDIA, but this is less logical than KEY_PLAYPAUSE,
which has much broader userspace support.

For example, the Chrome OS userspace now supports KEY_PLAYPAUSE to toggle
play/pause of videos and audio, but does not handle KEY_MEDIA.

Furthermore, Android itself now supports KEY_PLAYPAUSE equivalently, as the
new USB headset spec requires KEY_PLAYPAUSE for BTN_0.
https://source.android.com/devices/accessories/headset/usb-headset-spec

The same fix is required on Chrome kbl_da7219_max98357a.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The machine driver is a generic machine driver for SOF with rt5682
codec. it currently supports BYT/CHT/ICL/CML. Depending on the SOC
hdmi/speaker and DMIC support are added dynamically.

Only add information related to SOF since the machine driver was
only tested with SOF.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Semicolon is better than comma.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add dmic dai links using naming conventions used in
previous machine drivers.

Tested on whiskylake & icelake with SOF driver. Due
to a missing topology file, the DMIC functionality
could not be tested with the Skylake driver but was
tested for non-regressions on a GeminiLake platform
without DMICs.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add ipc dump function to CNL+ platforms.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add IPC dump function for APL plaform
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Dump IPC status when IPC timed out. IPC status is platform specific and
need bind to plaform.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The prepare() ioctl for BE dai link gets called both
when the stream is started and when it is resumed from
suspend. SOF uses this ioctl to set the hw params
again only if the stream has been suspended.

When the stream is started, the hw_params ioctl gets called
before prepare() and hw_params is set for the BE dai link.
So the prepare call does not need to do anything further.

When the stream resumes after system suspend, SOF requires
that the hw_params be set again for the BE dai. In order
to determine which streams should set the hw params
during prepare(), an internal flag called "hw_params_upon_resume"
is introduced in struct sof_intel_hda_stream. The flag is set
for hda streams when the sof device suspends and is
cleared after hw_params is set.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The stream and IPC share the same interrupt. The stream interrupt
handler mistakenly uses the ipc interrupt and return IRQ_HANDLED,
causing the ipc interrupt to be missed.

Make sure the stream interrupt handler only deals with stream-related
interrupts.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add stream_max into struct sof_intel_hda_dev to store the total hda
stream number that the platform can support, and initialize it at
stream_init.

This can be used later e.g. for stream bitmask.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When using a shared IRQ between IPC interrupt and stream IOC interrupt,
the interrupt handlers need to check the interrupt source before
scheduling their respective IRQ threads. In the case of IPC handler, it
should check if it is an IPC interrupt before waking up the IPC IRQ
thread.

The IPC IRQ thread, once scheduled, does not need to check the IRQ
source again. So, remove the superfluous check in the thread. Remove the
irq_status field from snd_sof_dev struct also as it is no longer needed.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Switch to a wrapper function which schedules the actual call of
snd_pcm_period_elapsed after the current IPC is completed.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>