according to datasheet complete control register is of 2 bytes.
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdfSigned-off-by: Nizam Haider <nijam.h@hcl.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Several ADC channels are supported in PMIC which can be used to
measure voltage, temperature, current etc. Different scaling can be
applied on the obtained voltage to report in physical units. Scaling
functionality can be different per channel. Add scaling support per
channel. Every channel present in adc has an unique conversion formula
for obtained voltage. Add support to report in Raw as well as in
processed format. Scaling is applied when processed read is requested
and is not applied when a Raw read is requested.
Signed-off-by: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Several channels are supported in ADC of PMIC which can be used to
measure voltage, temperature, current etc., Hardware provides
readings for all channels in adc code. That adc code needs to be
converted to voltage. Logic for conversion of adc code to voltage
is common for all ADC channels(voltage, temperature, current
.,etc). Implement separate function for generic conversion logic.
Signed-off-by: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The alignment of the #defines at the top of the file is not consistent.
This changes all of the defines to use consistent alignment to improve
the code readability.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

isl29028_chip_init() contains the device driver defaults and
two I2C calls that detect the presence of the chip. This patch
moves these into isl29028_probe() so that this function can
be used by the power management runtinme in a followup patch. This
patch also renames isl29028_chip_init() to
isl29028_chip_init_and_power_on().
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

There are two callers to the function isl29028_set_als_ir_mode() and
both instances use a nested if statement to only change the chip state
if it is not in the proper mode. This patch moves this check into the
isl29028_set_als_ir_mode() function to remove the nested if
statements.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

At the end of function ad7150_write_event_config(), directly returns 0.
As a result, the errors will be ignored by the callers. It may be better
to return variable "ret".
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

In function cm3232_reg_init(), it returns 0 even if the last call to
i2c_smbus_write_byte_data() returns a negative value (indicates error).
As a result, the return value may be inconsistent with the execution
status, and the caller of cm3232_reg_init() will not be able to detect
the error. This patch fixes the bug.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188641Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch fixes the following checkpatch.pl warning in ad7150.c
WARNING: Symbolic permissions 'S_IRUGO | S_IWUSR' are not preferred
Occured during build.
Signed-off-by: Amit Kushwaha <kushwaha.a@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Added timestamp channel. With this change, each sample has a timestamp.
This timestamp can be from the sensor hub when present or local kernel
timestamp. HID sensors can send timestamp with input data using usage id
HID_USAGE_SENSOR_TIME_TIMESTAMP. This timestamp value is converted to
nano seconds before pushing this sample to the iio core.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

msleep(1~20) may not do what the caller intends, and will often sleep longer.
(~20 ms actual sleep for any value given in the 1~20ms range)
This is not the desired behaviour for many cases like device resume time,
device suspend time, device enable time, data reading time, etc.
Thus, change msleep to usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The copyright year can not be in the future.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The module descriptions for the ADIS 16201, 16203 and 16209 drivers do not
match the actual function of the devices. Update them accordingly to fix
this.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

smatch warned:
	sval_binop_signed: invalid divide LLONG_MIN/-1

and this fixes it. It's actually good to have, in order to avoid accidental
checking for negative return values here.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Support driver probe by reading unique HID on systems based on ACPI instead
of DT compatible strings.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Compatible strings are not available on ACPI based systems. This patch adds
support to use DSDT information read from platform BIOS instead for probing
st pressure sensors.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add support to probe st_accel sensors on i2c bus using ACPI. Compatible
strings are not avaialable on ACPI based systems.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add support to match st sensors using information passed from ACPI DST
tables.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove two passthrough macros that are only called from a single
location and make the resultant vmcall directly.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the already defined DIAG_SEVERITY values directly instead of special
postcode macro names.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There were two instances of FAILURE being misspelled in the s-Par
firmware postcode event enum that are fixed.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove guestlinuxdebug enum values that are no longer being used and
renumber remaining values accordingly.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The visorchipset.c functionality was moved into the visorbus driver
previously. This patch updates the s-Par firmware postcode values to
reflect this status.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_4.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_3.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_2.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use CURRENT_FILE_PC directly in the POSTCODE_LINUX macro instead of
relying on passthrough macros to provide it.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Leverage the 3 existing s-Par postcode macros to do a bit more work
and provide only 1 base postcode macro.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes all the unused pound defines currently in
vbuschannel.h.
Signed-off-by: Erik Arfvidson <erik.arfvidson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes all the unused pound defines currently in
vmcallinterface.h.
Signed-off-by: Erik Arfvidson <erik.arfvidson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dgnc driver has no business creating "custom" sysfs files just for a
single tty driver.  Combined with the odd way they are created, it's
just a mess, so remove them entirely as I am tired of tripping over them
when doing driver core changes.

Cc: Lidza Louina <lidza.louina@gmail.com>
Cc: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes sm750fb tabstop style warning
found by checkpatch.pl tool
Signed-off-by: Andrea Ghittino <aghittino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The scripts to replace NULL test got confused with the
macro parenthesis so the unlikely test in libcfs_private.h
ended up incorrect. This fixes this error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Trivial fix to spelling mistake "oustanding" to "outstanding".
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove one blank line in sequence of two empty lines.
Signed-off-by: Dawid Kurek <dawikur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Align parameters to open parenthesis.
Signed-off-by: Dawid Kurek <dawikur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"revId" needs to be unsigned because we use it to test:

	if (revId == SM750LE_REVISION_ID) {

and SM750LE_REVISION_ID is ((unsigned char )0xfe).

Fixes: 81dee67e ("staging: sm750fb: add sm750 to staging")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver was actually released with BSD license. It also gained GPL
when it was submitted to be included in the kernel.

Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: gzhou1 <guojian.zhou@windriver.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes UPDATE_STATS_GB macro in slic.h header file
and just inline code. This improve readability.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>