Remove Mitesh Ahuja <mitesh.ahuja@avagotech.com> from
maintainers file. This email address seems not active
and causes to mail bounces during submissions.
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

__ib_umem_release calls dma_unmap_sg with a different number of
sg_entries than ib_umem_get uses for dma_map_sg. This might cause
trouble for implementations that merge sglist entries and results
in the following dma debug complaint:

DMA-API: device driver frees DMA sg list with different entry
         count [map count=2] [unmap count=1]

Fix it by using the correct value.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch avoids that Coverity complains about not checking the
ib_find_pkey() return value.

Fixes: commit 547af765 ("IB/multicast: Report errors on multicast groups if P_key changes")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch avoids that Coverity reports the following:

    Using uninitialized value port_attr.state when calling printk

Fixes: commit 94232d9c ("IPoIB: Start multicast join process only on active ports")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The array ib_mad_mgmt_class_table.method_table has MAX_MGMT_CLASS
(80) elements. Hence compare the array index with that value instead
of with IB_MGMT_MAX_METHODS (128). This patch avoids that Coverity
reports the following:

Overrunning array class->method_table of 80 8-byte elements at element index 127 (byte offset 1016) using index convert_mgmt_class(mad_hdr->mgmt_class) (which evaluates to 127).

Fixes: commit b7ab0b19 ("IB/mad: Verify mgmt class in received MADs")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Report the following message only once if no ACL has been configured
yet for an initiator port:

"Rejected login because no ACL has been configured yet for initiator %s.\n"
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The function usnic_ib_qp_grp_get_chunk only returns an ERR_PTR value or a
valid pointer, never NULL.  The same is true of get_qp_res_chunk, which
just returns the result of calling usnic_ib_qp_grp_get_chunk.  Simplify
IS_ERR_OR_NULL to IS_ERR in both cases.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,e;
@@

t = \(usnic_ib_qp_grp_get_chunk(...)\|get_qp_res_chunk(...)\)
... when != t=e
- IS_ERR_OR_NULL(t)
+ IS_ERR(t)

@@
expression t,e,e1;
@@

t = \(usnic_ib_qp_grp_get_chunk(...)\|get_qp_res_chunk(...)\)
... when != t=e
?- t ? PTR_ERR(t) : e1
+ PTR_ERR(t)
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

from "InfiBand Architecture Specifications Volume 1":

  A QP is said to have a stale connection when only one side has
  connection information. A stale connection may result if the remote CM
  had dropped the connection and sent a DREQ but the DREQ was never
  received by the local CM. Alternatively the remote CM may have lost
  all record of past connections because its node crashed and rebooted,
  while the local CM did not become aware of the remote node's reboot
  and therefore did not clean up stale connections.

and:

   A local CM may receive a REQ/REP for a stale connection. It shall
   abort the connection issuing REJ to the REQ/REP. It shall then issue
   DREQ with "DREQ:remote QPN” set to the remote QPN from the REQ/REP.

This patch solves a problem with reuse of QPN. Current codebase, that
is IPoIB, relies on a REAP-mechanism to do cleanup of the structures
in CM. A problem with this is the timeconstants governing this
mechanism; they are up to 768 seconds and the interface may look
inresponsive in that period.  Issuing a DREQ (and receiving a DREP)
does the necessary cleanup and the interface comes up.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

There are several places, where errors in dma_map_single() are
ignored. The patch fixes them.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The kernel side is #ifdef'd to this type, and the UAPI header
should use it directly. It has slightly different alignment
requirments from the usual user space version.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

and rename class version define to indicate SM rather than SMP or SMI
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When creating a FWD rule using tc create also a HW counter
for this rule.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Currently the code supports only drop rules to possess counters,
add that ability also for fwd rules.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Currently when calling mlx5_add_flow_rule we accept
only one flow destination, this commit allows to pass
multiple destinations.

This change forces us to change the return structure to a more
flexible one. We introduce a flow handle (struct mlx5_flow_handle),
it holds internally the number for rules created and holds an array
where each cell points the to a flow rule.

From the consumers (of mlx5_add_flow_rule) point of view this
change is only cosmetic and requires only to change the type
of the returned value they store.

From the core point of view, we now need to use a loop when
allocating and deleting rules (e.g given to us a flow handler).
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

When adding a new rule, if we can match it with compare_match_value and
flow tag we might be able to insert the rule to the same fte.
In order to do that, there must be an overlap between the actions of the
fte and the new rule.

When updating the action of an existing fte, we must tell the firmware
we are doing so.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

The way we compare between two dests will need to be used in other
places in the future, so we factor out the comparison logic
between two dests into a separate function.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

An fte status becomes FS_FTE_STATUS_EXISTING only after it was
created in HW. We can use this in order to simplify the logic on
what firmware command to use. If the status isn't FS_FTE_STATUS_EXISTING
we need to create the fte, otherwise we need only to update it.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

When adding a new rule to an fte, we need to hold the fte lock
until we add that rule to the fte and increase the fte ref count.

Fixes: 0c56b975 ("net/mlx5_core: Introduce flow steering API")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Implement the vf set rate ndo by modifying the TSAR vport rate limit.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Add TSAR to the eswitch which will act as the vports rate limiter.
Create/Destroy TSAR on Enable/Dsiable SRIOV.
Attach/Detach vport to eswitch TSAR on Enable/Disable vport.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

TSAR (stands for Transmit Scheduling ARbiter) is a hardware component
that is responsible for selecting the next entity to serve on the
transmit path.
The arbitration defines the QoS policy between the agents connected to
the TSAR.
The TSAR is a consist two main features:
1) BW Allocation between agents:
The TSAR implements a defecit weighted round robin between the agents.
Each agent attached to the TSAR is assigned with a weight and it is
awarded transmission tokens according to this weight.
2) Rate limer per agent:
Each agent attached to the TSAR is (optionally) assigned with a rate
limit.
TSAR will not allow scheduling for an agent exceeding its defined rate
limit.

In this patch we implement the API of manipulating the TSAR.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

For the mlx5 driver to support ConnectX-5 PCIe 4.0 VFs, we add the
device ID "0x101a" to mlx5_core_pci_table.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

According to PRM async_event_mask have to be 64 bits long.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

SRQ physical address structure field should be in big-endian format.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Update struct mlx5_ifc_xrqc_bits according to last specification
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Do not dispatch unknown mlx5 core events on mlx5_ib_event.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>

Pull x86 bugfix from Thomas Gleixner:
 "A single bugfix for the recent changes related to registering the boot
  cpu when this has not happened before prefill_possible_map().

  The main problem with this change got fixed already, but we missed the
  case where the local APIC is not yet mapped, when prefill_possible_map()
  is invoked, so the registration of the boot cpu which has the APIC bit
  set in CPUID will explode.

  I should have seen that issue earlier, but all I can do now is feeling
  embarassed"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smpboot: Init apic mapping before usage

Pull ubi/ubifs fixes from Richard Weinberger:
 "This contains fixes for issues in both UBI and UBIFS:

   - A regression wrt overlayfs, introduced in -rc2.
   - An UBI issue, found by Dan Carpenter's static checker"

* tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs:
  ubifs: Fix regression in ubifs_readdir()
  ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()

Pull ARM SoC fixes from Olof Johansson:
 "We haven't seen a whole lot of fixes for the first two weeks since the
  merge window, but here is the batch that we have at the moment.

  Nothing sticks out as particularly bad or scary, it's mostly a handful
  of smaller fixes to several platforms. The Uniphier reset controller
  changes could probably have been delayed to 4.10, but they're not
  scary and just plumbing up driver changes that went in during the
  merge window.

  We're also adding another maintainer to Marvell Berlin platforms, to
  help out when Sebastian is too busy. Yay teamwork!"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
  ARM: dts: vf610: fix IRQ flag of global timer
  ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
  ARM: imx: gpc: Initialize all power domains
  arm64: dts: Updated NAND DT properties for NS2 SVK
  arm64: dts: uniphier: change MIO node to SD control node
  ARM: dts: uniphier: change MIO node to SD control node
  reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
  arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
  ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
  arm64: dts: Add timer erratum property for LS2080A and LS1043A
  arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
  ARM: multi_v7_defconfig: Enable Intel e1000e driver
  MAINTAINERS: add myself as Marvell berlin SoC maintainer
  bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
  ARM: dts: fix the SD card on the Snowball
  arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
  arm64: dts: marvell: fix clocksource for CP110 master SPI0
  ARM: mvebu: Select corediv clk for all mvebu v7 SoC

Pull char/misc driver fixes from Greg KH:
 "Here are a few small char/misc driver fixes for reported issues.

  The "biggest" are two binder fixes for reported issues that have been
  shipping in Android phones for a while now, the others are various
  fixes for reported problems.

  And there's a MAINTAINERS update for good measure.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  MAINTAINERS: Add entry for genwqe driver
  VMCI: Doorbell create and destroy fixes
  GenWQE: Fix bad page access during abort of resource allocation
  vme: vme_get_size potentially returning incorrect value on failure
  extcon: qcom-spmi-misc: Sync the extcon state on interrupt
  hv: do not lose pending heartbeat vmbus packets
  mei: txe: don't clean an unprocessed interrupt cause.
  ANDROID: binder: Clear binder and cookie when setting handle in flat binder struct
  ANDROID: binder: Add strong ref checks

Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.

* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
  arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes

This pull request contains a single fix for Broadcom ARM64-based SoCs:

- Ray adds the required bus width and OOB sector size properties to the
  Northstar 2 SVK reference board in order for the NAND controller to work
  properly

* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
  arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.9:
 - A couple of patches from Fabio to fix the GPC power domain regression
   which is caused by PM Domain core change 0159ec67
   ("PM / Domains: Verify the PM domain is present when adding a
   provider"), and a related kernel crash seen with multi_v7_defconfig
   build.
 - Correct the PHY ID mask for AR8031 to match phy driver code.
 - Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
 - Correct vf610 global timer IRQ flag to avoid warning from gic driver
   after commit 992345a5 ("irqchip/gic: WARN if setting the
   interrupt type for a PPI fails").

* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
  ARM: dts: vf610: fix IRQ flag of global timer
  ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
  ARM: imx: gpc: Initialize all power domains
  arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-fixes-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into fixes

UniPhier ARM SoC fixes for v4.9

- Add "select ARCH_HAS_RESET_CONTROLLER" in Kconfig
- Rename wrongly-named mioctrl to sdctrl

* tag 'uniphier-fixes-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: change MIO node to SD control node
  ARM: dts: uniphier: change MIO node to SD control node
  reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
  arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
  ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull driver core fixes from Greg KH:
 "Here are two small driver core / kernfs fixes for 4.9-rc3.

  One makes the Kconfig entry for DEBUG_TEST_DRIVER_REMOVE a bit more
  explicit that this is a crazy thing to enable for a distro kernel
  (thanks for trying Fedora!), the other resolves an issue with vim
  opening kernfs files (sysfs, configfs, etc.)

  Both have been in linux-next with no reported issues"

* tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: Make Kconfig text for DEBUG_TEST_DRIVER_REMOVE stronger
  kernfs: Add noop_fsync to supported kernfs_file_fops

Pull staging and IIO driver fixes from Greg KH:
 "Here are some small staging and iio driver fixes for reported issues
  for 4.9-rc3. Nothing major, the "largest" being a lustre fix for a
  sysfs file that was obviously wrong, and had never been tested, so it
  was moved to debugfs as that is where it belongs. The others are small
  bug fixes for reported issues with various staging or iio drivers.

  All have been in linux-next for a while with no reported issues"

* tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  greybus: fix a leak on error in gb_module_create()
  greybus: es2: fix error return code in ap_probe()
  greybus: arche-platform: Add missing of_node_put() in arche_platform_change_state()
  staging: android: ion: Fix error handling in ion_query_heaps()
  iio: accel: sca3000_core: avoid potentially uninitialized variable
  iio:chemical:atlas-ph-sensor: Fix use of 32 bit int to hold 16 bit big endian value
  staging/lustre/llite: Move unstable_stats from sysfs to debugfs
  Staging: wilc1000: Fix kernel Oops on opening the device
  staging: android/ion: testing the wrong variable
  Staging: greybus: uart: Use gbphy_dev->dev instead of bundle->dev
  Staging: greybus: gpio: Use gbphy_dev->dev instead of bundle->dev
  iio: adc: ti-adc081c: Select IIO_TRIGGERED_BUFFER to prevent build errors
  iio: maxim_thermocouple: Align 16 bit big endian value of raw reads

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small tty and serial driver fixes for reported
  issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
  problems with the tty core changes that are in 4.9-rc1, and finally
  the atmel serial driver is back working properly.

  All have been in linux-next with no reported issues"

* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
  tty: serial_core: Fix serial console crash on port shutdown
  tty/serial: at91: fix hardware handshake on Atmel platforms
  vt: clear selection before resizing
  sc16is7xx: always write state when configuring GPIO as an output
  sh-sci: document R8A7743/5 support
  tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
  tty: limit terminal size to 4M chars
  tty: serial: fsl_lpuart: Fix Tx DMA edge case
  serial: 8250_lpss: enable MSI for sure
  serial: core: fix console problems on uart_close
  serial: 8250_uniphier: fix clearing divisor latch access bit
  serial: 8250_uniphier: fix more unterminated string
  serial: pch_uart: add terminate entry for dmi_system_id tables
  devicetree: bindings: uart: Add new compatible string for ZynqMP
  serial: xuartps: Add new compatible string for ZynqMP
  serial: SERIAL_STM32 should depend on HAS_DMA
  serial: stm32: Fix comparisons with undefined register
  tty: vt, fix bogus division in csi_J

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 4.9-rc3.

  There is the usual number of gadget and xhci patches in here to
  resolved reported issues, as well as some usb-serial driver fixes and
  new device ids.

  All have been in linux-next with no reported issues"

* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  usb: chipidea: host: fix NULL ptr dereference during shutdown
  usb: renesas_usbhs: add wait after initialization for R-Car Gen3
  usb: increase ohci watchdog delay to 275 msec
  usb: musb: Call pm_runtime from musb_gadget_queue
  usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
  usb: ehci-platform: increase EHCI_MAX_RSTS to 4
  usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
  USB: serial: fix potential NULL-dereference at probe
  xhci: use default USB_RESUME_TIMEOUT when resuming ports.
  xhci: workaround for hosts missing CAS bit
  xhci: add restart quirk for Intel Wildcatpoint PCH
  USB: serial: cp210x: fix tiocmget error handling
  wusb: fix error return code in wusb_prf()
  Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
  Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
  Revert "usb: dwc2: gadget: change variable name to more meaningful"
  USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
  wusb: Stop using the stack for sg crypto scratch space
  usb: dwc3: Fix size used in dma_free_coherent()
  usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
  ...