Improve code readability by using enum and a
switch-case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This fixes checkpatch warning from the latest
3.11-rc kernel tree.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Remove useless code that was causing WARN_ON when
a 80MHz+ vif entered promiscuous mode or monitor
interface was started.

The channel mode is already computed by
chan_to_phymode().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Handle pci_alloc_consistent(), kmalloc()
errors in copy engine module.
Found during code review.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The latest supported and available FW build is 1.0.0.636.
Reflect this in ath10k code.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Since the firmware support is no longer available for hw1.0,
drop all code (especially workarounds) for those units.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Setup UAPSD peer/peer rate flags correctly.
WMI_RC_UAPSD_FLAG is a peer rate capabilities flag
and should not be set as a peer flag.
Found during code review, doesn't fix a known
issues.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In our Fuz testing, reference client corrupts the dest mac to "00:00:00:00:00:00"
in the WPA2 handshake no 2. During driver init the sta_list entries mac
addresses are by default "00:00:00:00:00:00". Driver returns an invalid
pointer (conn) and the drver shall crash, if rxtids (aggr_conn)
skb queues are accessed, since they would not be initialized.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Make sure to cancel heart beat timer before
freeing wmi to avoid potential NULL pointer
dereference.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Unify the PCI options location.

By default the SoC PS option is disabled to boost the
performance and due to poor stability on early HW revisions.
In future we can remove the module parameter and turn on/off
the PS for given hardware.

This change also makes the pci module parameter for SoC PS static.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This fixes interrupt-related issue when no
interfaces were running thus the device was
considered powered down.

The power_down() function isn't really powering
down the device. It simply assumed it won't
interrupt. This wasn't true in some cases and
could lead to paging failures upon FW indication
interrupt (i.e. FW crash) because some structures
aren't allocated in that device state.

One reason for that was that ar_pci->started
wasn't reset. The other is interrupts should've
been masked when teardown starts.

The patch reorganized interrupt setup and makes
sure ar_pci->started is reset accordingly.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

pci_disable_msi() must be called if the initial
request_irq() fails.

Also add a warning message so it's possible to
distinguish request_irq() failure and
pci_enable_msi() failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The private memory area in vif provided by
mac80211 isn't guaranteed to be zeroed.

This patch should fix issues when switching
between STA and AP interface types.

The tim_bitmap could become polluted by STA bssid
field (since it's a union), wep_keys array
could also become polluted with invalid pointers
and probably much more.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Apparently the available firmware has a limit of
handling 7 APs, 3 GOs or 8 STAs. This is based on
empirical tests and it is still possible some
combinations may crash the firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Normally user specifies broadcast ssid for
scanning. If the user wants to do a passive scan
it does not pass any ssids.

The patch makes sure we ath10k tells firmware to
not send anything at all in case it decides no
ssids equals broadcast ssid.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If the device is removed and hotplug fails
ioread32() will return 0xFFFFFFFF. In that case
reading ringbuffer during device bringup led to
out-of-bounds addressing of a ringbuffer array
that in turn led to a paging failure.

This could be reproduced by the following:
 * boot without acpi/prevent hotplug from working
 * insert and manually detect (pci rescan) the device
 * remove the device physically
 * load ath10k driver
 * kernel crashed

Ringbuffer index reading is now protected by using
an appropriate mask to prevent addressing an
invalid array index.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This implements a limited subset of what can be
reported in the survey dump.

This can be used for assessing approximate channel
load, e.g. for automatic channel selection.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

HW supports L3/L4 tx checksum offloading.

This should reduce CPU load and improve
performance on slow host machines.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

HW supports L3/L4 rx checksum offloading.

This should reduce CPU load and improve
performance on slow host machines.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Until now ath10k assumed 3 spatial streams.
However some devices support only 2 spatial
streams.

This patch improves performance on devices that
don't support 3 spatial streams.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It is more efficient to move just the 802.11
header instead of the whole payload in most cases.

This has no measurable effect on modern hardware.
It should improve performance by a few percent on
hardware such as an Access Point that have a slow
CPU compared to a typical desktop CPU.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If RTS and fragmentation threshold values are
0xFFFFFFFF they should be considered disabled and
no min/max limits must be applied.

This fixes some issues with throughput issues,
especially with VHT.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In some cases channel arrays were never freed.

The patch also unifies error handling in the mac
setup function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Endpoints are re-initialized upon HTC start anyway
so there's no need to do that twice in case of
restarting HTC (i.e. in case of hardware
recovery).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was possible to submit new HTC commands
after/while HTC stopped. This led to memory
corruption in some rare cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This can be useful for testing. To perform a
forced firmware crash write 'crash' to
'simulate_fw_crash' debugfs file. E.g.

  echo crash > /sys/kernel/debug/ieee80211/phy1/ath10k/simulate_fw_crash
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Tx processing functions dereference vif and caused
NULL to be dereferenced for injected frames.

Don't call these functions at all for injected
frames. It doesn't make much sense to do so
anyway.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This can be useful to test FW crash handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Restart the hardware if FW crashes.

If FW crashes during recovery we leave the
hardware in a "wedged" state to avoid recursive
recoveries.

When in "wedged" state userspace may bring
interfaces down (to issue stop()) and then bring
one interface (to issue start()) to reload
hardware manually.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If the device is not running then there may be no
FW at all to send the query to. If the FW is
already there it might still trigger a crash if
the command is sent before the device is fully
initialized.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Different FW versions may provide different
functions thus mean different hw capabilities
advertised to mac80211.

It is safe to swap firmware files on disk during
driver/device runtime without worries.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This fixes suspend-to-disk. The hardware is now
re-initialized upon freeze/thaw properly.

This also makes suspend/resume re-initialize the
hardware as WoWLAN support is not done yet.

With some little work it should be possible to
support hw reconfiguration for hw/fw recovery.

HW must be initialized once before registering to
mac80211 because FW determinates what hw
capabilities can be advertised.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is necessary for proper hw reconfiguration
and to avoid memory leaks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is necessary for hw reconfiguration to work.
Since mac80211 is not calling remove_interface()
is such case we must reset free_vdev_map.

Also use a define instead of a hardcoded value for
vdev map initialization.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Split up fw-related and hw-related suspension code.

Although we don't advertise WoW support to
mac80211 yet it's useful to keep the code in
suspend/resume hooks.

At this point there's no need to keep pci pm ops.
In case of WoW mac80211 calls ath10k_suspend()
which should take care of entering low-power mode.
In case WoW is not available mac80211 will go
through regular interface teradown and use start/stop.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is necessary if we want to be able to restart
hw on-the-fly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Regulatory domain notification hook can be called
regardless of the hw state (i.e. before start
mac80211 callback).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Enables code reuse for proper hw reconfiguration
that is in turn required for proper
suspend/hibernation/wowlan support.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Split logic that prepares the device for BMI
phase/cleans up related resources.

This is necessary for ath10k to be able to restart
hw on the fly without reloading the module.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>