According to the PRM (Vol3P2), the PCH FDI receiver ISR read for bit lock
should be retried at least once. This patch retries the read 5 times
with a small delay in between reads. I've had reports of display corruption
on resume with "FDI train 1 fail!", so I'm hoping that adding this retry
will mitigate the issue.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

They're not really errors (well actually I don't know; I don't
understand _DSM and _MUX well enough to say, but I do know they spam
people's logs and seem to be harmless).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: The _DSM error got remove in another patch already]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44250Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This change enables the use of displays where the vbt table just
contains inappropriate values, but either the vesa defaults or
the video=... modes do something sensible with the attached display.

The problem happens with an embedded board that contains vbt bios
tables that do not match the attached display.  Using this change and
the appropriate kernel boot command line they are able to use an
otherwise completely unusable secondary display on that embedded
board.
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Mathias Froehlich <Mathias.Froehlich@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

By clearing the GPU read domains before waiting upon the buffer, we run
the risk of the wait being interrupted and the domains prematurely
cleared. The next time we attempt to wait upon the buffer (after
userspace handles the signal), we believe that the buffer is idle and so
skip the wait.

There are a number of bugs across all generations which show signs of an
overly haste reuse of active buffers.

Such as:

  https://bugs.freedesktop.org/show_bug.cgi?id=29046
  https://bugs.freedesktop.org/show_bug.cgi?id=35863
  https://bugs.freedesktop.org/show_bug.cgi?id=38952
  https://bugs.freedesktop.org/show_bug.cgi?id=40282
  https://bugs.freedesktop.org/show_bug.cgi?id=41098
  https://bugs.freedesktop.org/show_bug.cgi?id=41102
  https://bugs.freedesktop.org/show_bug.cgi?id=41284
  https://bugs.freedesktop.org/show_bug.cgi?id=42141

A couple of those pre-date i915_gem_object_finish_gpu(), so may be
unrelated (such as a wild write from a userspace command buffer), but
this does look like a convincing cause for most of those bugs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

With the rework to merge the bit-banging fallback into the gmbus
i2c adapter we've gotten rid of the deadlock possibility that
originally lead to the disabling of this code.

This reverts the revert

commit 826c7e41
Author: Jean Delvare <khali@linux-fr.org>
Date:   Sat Jun 4 19:34:56 2011 +0000

    Revert "drm/i915: Enable GMBUS for post-gen2 chipsets"

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35572Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This way we can simplify the setup and teardown a bit.

Because we don't actually allocate anything anymore for the force_bit
case, we can now convert that into a boolean.

Also and the functionality supported by the bit-banging together with
what gmbus can do, so that this doesn't randomly change any more.

v2: Chris Wilson noticed that I've mixed up && and & ...

v3: Clarify an if block as suggested by Eugeni Dodonov.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

... and directly call the newly exported i2c bit-banging functions.

The code is still pretty convoluted because we only set up the gpio
i2c stuff when actually falling back, resulting in more complexity
than necessary. This will be fixed up in the next patch.

v2: Use exported i2c_bit_algo vtable instead of exported functions.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

When we set up the gpio fallback, we always have a 1:1 relationship
with an intel_gmbus. Exploit that to store all gpio related data in
there, too. This is a preparation step to merge the tw i2c adapters
controlling the same bus into one.

Just mundane code-munging in this patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

i915 has a hw i2c controller (gmbus) but for a bunch of stupid reasons
we need to be able to fall back to the bit-banging algo on gpio pins.

The current code sets up a 2nd i2c controller for the same i2c bus using
the bit-banging algo. This has a bunch of issues, the major one being
that userspace can directly access this fallback i2c adaptor behind
the drivers back.

But we need to frob a few registers before and after using fallback
gpio bit-banging, so this horribly fails.

The new plan is to only set up one i2c adaptor and transparently fall
back to bit-banging by directly calling the xfer function of the bit-
banging algo in the i2c core.

To make that possible, export the 2 i2c algo functions.

v2: As suggested by Jean Delvare, simply export the i2c_bit_algo
vtable instead of the individual functions.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

I'd like to export the corresponding functions from the i2c core
so that I can use them in fallback bit-banging in i915.ko

v2: Adapt to new i2c export patch.

Cc: nouveau@lists.freedesktop.org
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This way we can free up the bus->adaptor.algo_data pointer and make it
available for use with the bitbanging fallback algo.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

gmbus_xfer with a single message (particularly a single message write) would
set Bus Cycle Select to 100b, the Gen Stop cycle, instead of 101b,
No Index, Stop cycle. This would not start single message i2c transactions.

Also, gmbus_xfer done: will disable the interface without checking if
it is idle. In the case of writes, there will be no wait on status or delay
to ensure the write starts and completes before the interface is turned off.

Fixed the former issue by using the same cycle selection as used in the
I2C_M_RD for the write case.
GMBUS_CYCLE_WAIT | (i + 1 == num ? GMBUS_CYCLE_STOP : 0)
Fixed the latter by waiting on GMBUS_ACTIVE to deassert before disable.

Note from the grumpy d-i-n maintainer: The first hunk that changes the
gmbus read path is just cosmetics to align the code with the write
path.  I.e. the commit message above is slightly lying because the
first issue is _only_ with writes (and not simply "particularly").
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

gcc seems to get uber-anal recently about these things.

Clarification from Dan Carpenter:

"Sorry, I should have said that it's not a gcc warning, it's a smatch
thing.  But also it's not uber-anal.  It's the exact level of anality
which is required to make the == -1 test work.  You can compare
unsigned int and longs to -1 and it works but for smaller types it
doesn't."
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This error message has since been superseded by the hangcheck, and does
not add any salient information beyond that already printed by hangcheck
discovering the GPU hang that lead to i915_wait_request() bombing out in
the first place.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

While fixing up a merge conflict with drm-next I've noticed that we
use the same audio drm connector property also for dp and sdvo
outputs.

So put the new enum to some good use and convert these paths, too. The
HDMI_AUDIO_ prefix is a bit a misnomer. But at least for sdvo it makes
sense (and you can also connect a hdmi monitor with a dp->hdmi cable),
so I've decided to stick with it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Retiring requests does not typically free up space in the aperture,
so the additional search is pointless.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Incrementing the reference count on all objects walked when searching
for space in the aperture is a non-neglible amount of overhead. In fact,
we only need to hold on to a reference for objects that we will evict,
so we can therefore delay the referencing until we find a suitable hole
and only add those objects that fall inside.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

As we warn the user later that we cannot find or load the VBIOS,
explaining why is an exercise in debugging. Shouting *ERROR* upsets
people and produces bug reports.
Reported-by: Michael Rieder <mr@student.ethz.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43751Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Add a no_lvds quirk for the HP t5745 and HP st5747 thin clients

dmidecode for those thin clients are attached in thoses bugs:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/911916
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/911920Signed-off-by: Marc Gariepy <mgariepy@ubuntu.com>
Acked-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Fixes LP: #796030 by removing forced pipe A on HP 2730p.  Quirk has
previously been introduced to fix a sleep mode problem that does not
exist any more.

v2: Added Tested-by and Bugzilla Link

Bugzilla: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/796030Tested-by: Ronny Standtke <ronny.standtke@gmx.net>
Signed-off-by: Philipp Grete <mail@pgrete.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Manually resolve the conflict between the new enum drm property
helpers in drm-next and the new "force-dvi" option that the "audio" output
property gained in drm-intel-next.

While resolving this conflict, switch the new drm_prop_enum_list to
use the newly introduced enum defines instead of magic values.

Conflicts:
	drivers/gpu/drm/i915/intel_modes.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

For the simple KMS driver case we need some more info about what the preferred
depth and if a shadow framebuffer is preferred.

I've only added this for intel/radeon which support the dumb ioctls so far.

If you need something really fancy you should be writing a real X.org driver.

v2: drop cursor information, just return an error from the cursor ioctls
and we can make userspace fallback to sw cursor in that case, cursor
info was getting too messy, best to start smaller.
Signed-off-by: Dave Airlie <airlied@redhat.com>

The current enabling of bus mastering in the drm midlayer allows a large
race condition under kexec. When a kexec'ed kernel re-enables bus mastering
for the GPU, previously setup dma blocks may cause writes to random pieces
of memory. On radeon the writeback mechanism can cause these sorts of issues.

This patch doesn't fix the problem, but it moves the bus master enable under
the individual drivers control so they can move enabling it until later in
their load cycle and close the race.

Fix for radeon kms driver will be in a follow-up patch.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This reverts commit e167976e,
Since this was already fixed in commit
3bd3c932 some days before this
commit cause seq_file.h to be included twice.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We store stuff in texdw[7] so this array needs to have 8 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

With the introduction of the PCH, we gained an LVDS presence pin but we
continued to use the existing logic that asserted that LVDS was only
supported on certain mobile chipsets. However, there are desktop
IronLake systems with LVDS attached which we fail to detect. So for PCH,
trust the LVDS presence pin and quirk all the lying manufacturers.
Tested-by: Daniel Woff <wolff.daniel@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43171Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

So that we can tally the request against the command sequence in the
ringbuffer, or merely jump to the interesting locations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Being able to tally the list of outstanding requests with the sequence
of commands in the ringbuffer is often useful evidence with respect to
driver corruption.

Note that since this is the umpteenth per-ring data structure to be added
to the error state, I've coallesced the nearby loops (the ringbuffer and
batchbuffer) into a single structure along with the list of requests.  A
later task would be to refactor the ring register state into the same
structure.

v2: Fix pretty printing of requests so that they are parsed correctly by
intel_error_decode and use the 0x%08x format for seqno for consistency
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

By recording the location of every request in the ringbuffer, we know
that in order to retire the request the GPU must have finished reading
it and so the GPU head is now beyond the tail of the request. We can
therefore provide a conservative estimate of where the GPU is reading
from in order to avoid having to read back the ring buffer registers
when polling for space upon starting a new write into the ringbuffer.

A secondary effect is that this allows us to convert
intel_ring_buffer_wait() to use i915_wait_request() and so consolidate
upon the single function to handle the complicated task of waiting upon
the GPU. A necessary precaution is that we need to make that wait
uninterruptible to match the existing conditions as all the callers of
intel_ring_begin() have not been audited to handle ERESTARTSYS
correctly.

By using a conservative estimate for the head, and always processing all
outstanding requests first, we prevent a race condition between using
the estimate and direct reads of I915_RING_HEAD which could result in
the value of the head going backwards, and the tail overflowing once
again. We are also careful to mark any request that we skip over in
order to free space in ring as consumed which provides a
self-consistency check.

Given sufficient abuse, such as a set of unthrottled GPU bound
cairo-traces, avoiding the use of I915_RING_HEAD gives a 10-20% boost on
Sandy Bridge (i5-2520m):
  firefox-paintball  18927ms -> 15646ms: 1.21x speedup
  firefox-fishtank   12563ms -> 11278ms: 1.11x speedup
which is a mild consolation for the performance those traces achieved from
exploiting the buggy autoreported head.

v2: Add a few more comments and make request->tail a conservative
estimate as suggested by Daniel Vetter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: resolve conflicts with retirement defering and the lack of
the autoreport head removal (that will go in through -fixes).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This was pointed by Jesse Barnes. The code now seems to follow the
specification but I don't have an SDVO device to really test this.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge tag 'drm-intel-next-2012-02-07' of git://people.freedesktop.org/~danvet/drm-intel into drm-core-next

* tag 'drm-intel-next-2012-02-07' of git://people.freedesktop.org/~danvet/drm-intel: (29 commits)
  drm/i915: Handle unmappable buffers during error state capture
  drm/i915: rewrite shmem_pread_slow to use copy_to_user
  drm/i915: rewrite shmem_pwrite_slow to use copy_from_user
  drm/i915: fall through pwrite_gtt_slow to the shmem slow path
  drm/i915: add debugfs file for swizzling information
  drm/i915: fix swizzle detection for gen3
  drm/i915: Remove the upper limit on the bo size for mapping into the CPU domain
  drm/i915: add per-ring fault reg to error_state
  drm/i915: reject GTT domain in relocations
  drm/i915: remove the i915_batchbuffer_info debugfs file
  drm/i915: capture error_state also for stuck rings
  drm/i915: refactor debugfs create functions
  drm/i915: refactor debugfs open function
  drm/i915: don't trash the gtt when running out of fences
  drm/i915: Separate fence pin counting from normal bind pin counting
  drm/i915/ringbuffer: kill snb blt workaround
  drm/i915: collect more per ring error state
  drm/i915: refactor ring error state capture to use arrays
  drm/i915: switch ring->id to be a real id
  drm/i915: set AUD_CONFIG N_value_index for DisplayPort
  ...

GMBUS has several ports and each has it's own corresponding
I2C adpater. When multiple I2C adapters call gmbus_xfer() at
the same time there is a race condition in using the underlying
GMBUS controller. Fixing this by adding a mutex lock when calling
gmbus_xfer().

v2: Moved gmbus_mutex below intel_gmbus and added comments.
Rebased to drm-intel-next-queued.
Signed-off-by: Yufeng Shen <miletus@chromium.org>
[danvet: Shortened the gmbus_mutex comment a bit and add the patch
revision comment to the commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

When HDMI-DVI converter is used, it's not only necessary to turn off
audio, but also to disable HDMI_MODE_SELECT and video infoframe. Since
the DVI mode is mainly tied to audio functionality from end user POV,
add a new "force-dvi" audio mode:

	xrandr --output HDMI1 --set audio force-dvi

Note that most users won't need to set this and happily rely on the EDID
based DVI auto detection.
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This patch replaces the locking from the downclock routines with an assert
to ensure the registers are indeed unlocked. Without this patch, pre-SNB
devices would lock the registers when downclocking which would cause a
WARNING on suspend/resume with downclocking enabled.

Note: To hit this bug, you need to have lvds downclocking enabled.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

evergreen and northern island gpu needs more informations for 2D tiling
than previous r6xx/r7xx. Add field to tiling ioctl to allow userspace
to provide those.

The v8 cs checking change to track color view on r6xx/r7xx doesn't
affect old userspace as old userspace always emited 0 for this register.

v2 fix r6xx/r7xx 2D tiling computation
v3 fix r6xx/r7xx height align for untiled surface & add support for
   tile split on evergreen and newer
v4 improve tiling debugging output
v5 fix tile split code for evergreen and newer
v6 set proper tile split for crtc register
v7 fix tile split limit value
v8 add COLOR_VIEW checking to r6xx/r7xx checker, add evergreen cs
   checking, update safe reg for r600, evergreen and cayman.
   Evergreen checking need some work around for stencil alignment
   issues
v9 fix tile split value range, fix compressed texture handling and
   mipmap calculation, allow evergreen check to be silencious in
   front of current broken userspace (depth/stencil alignment issue)
v10 fix eg 3d texture and compressed texture, fix r600 depth array,
    fix r600 color view computation, add support for evergreen stencil
    split
v11 more verbose debugging in some case
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

v2: agd5f: add strmout CS checking, copy_dw register checking

v3: agd5f: don't use cs_check_reg() for copy_dw checking as it
will incorrectly patch the command stream for certain regs.

v4: agd5f: add warning if safe reg check fails for copy_dw

v5: agd5f: add stricter checking for 6xx/7xx

v6: agd5f: add range checking for copy_dw on eg+,
add sx_surface_sync to safe reg list for 7xx.

v7: agd5f: add stricter checking for eg+
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

* drm-vmware-next:
  drm/vmwgfx: Bump driver minor
  vmwgfx: Move function declaration to correct header
  drm/vmwgfx: Treat out-of-range initial width and height as host errors
  vmwgfx: Pick up the initial size from the width and height regs
  vmwgfx: Add page flip support
  vmwgfx: Pipe fence out of screen object dirty functions
  vmwgfx: Make it possible to get fence from execbuf
  vmwgfx: Clean up pending event references to struct drm_file objects on close
  vmwgfx: Rework fence event action

Bump driver minor to signal availability of the page-flip ioctl.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>