.. to be the same as startup.

In resolving MDEV-27461, BUF_LRU_MIN_LEN (256) is the minimum number of
pages for the innodb buffer pool size. Obviously we need more than just
flushing pages. Taking the 16k page size and its default minimum, an
extra 25% is needed on top of the flushing pages to make a workable buffer
pool.

The minimum innodb_buffer_pool_chunk_size (1M) restricts the minimum
otherwise we'd have a pool made up of different chunk sizes.

The resulting minimum innodb buffer pool sizes are:

Page Size, Previously minimum (startup), with change.
        4k                            5M           2M
        8k                            5M           3M
       16k                            5M           5M
       32k                           24M          10M
       64k                           24M          20M

With this patch, SET GLOBAL innodb_buffer_pool_size minimums are
enforced.

The evident minimum system variable size for innodb_buffer_pool_size
is 2M, however this is only setable if using 4k page size. As
the order of the page_size and buffer_pool_size aren't fixed, we can't
hide this change.

Subsequent changes:
* innodb_buffer_pool_resize_with_chunks.test - raised of pool resize due to new
  minimums. Chunk size also needed increase as the test was for
  pool_size < chunk_size to generate a warning.
* Removed srv_buf_pool_min_size and replaced use with MYSQL_SYSVAR_NAME(buffer_pool_size).min_val
* Removed srv_buf_pool_def_size and replaced constant defination in
  MYSQL_SYSVAR_LONGLONG(buffer_pool_size)
* Reordered ha_innodb to allow for direct use of MYSQL_SYSVAR_NAME(buffer_pool_size).min_val
* Moved buf_pool_size_align into ha_innodb to access to MYSQL_SYSVAR_NAME(buffer_pool_size).min_val
* loose-innodb_disable_resize_buffer_pool_debug is needed in the
  innodb.restart.opt test so that under debug mode, resizing of the
  innodb buffer pool can occur.

There were no InnoDB changes in the MySQL 5.7.37 release that would be
relevant to MariaDB Server. We will merely update the reported
InnoDB version number.

MDEV-26129 Bad results with join comparing case insensitive VARCHAR/ENUM/SET expression to a _bin ENUM column

Range optimizer incorrectly was used for ENUM columns
when the operation collation did not match the column collation.

Adding a virtual implementation of Field_enum::can_optimize_range()
which tests if the column and the operation collation match.

added dependency devel->shared and conflict with previous versions
update C/C 3.1 with the corresponding C/C part of the fix

information_schema.statistics.collation column needs OPEN_FULL_TABLE,
because it checks index_flags() for HA_READ_ORDER capability.

mtr detects a forced combination if the command line for a test already
includes all options from this combination. options are stored in a perl
hash as (key,value) pairs.

this breaks if the command line has two options with the same name,
like --plugin-load-add=foo --plugin-load-add=bar, and the combination
forces plugin foo.

In particular, this resulted in warnings when running
federated.federatedx_versioning test

The column INFORMATION_SCHEMA.INNODB_LOCKS.LOCK_DATA
would report NULL when the page that contains the locked
record does not reside in the buffer pool.

Pages may be evicted from the buffer pool due to some background
activity, such as the purge of transaction history loading
undo log pages to the buffer pool. The regression tests intentionally
run with a small buffer pool size setting.

To prevent the intermittent test failures, we will filter out the
contents of the LOCK_DATA column from the output.

Fix regression introduced in MDEV-19893

Some errors must be sent with seqno = 0, e.g those that are detected
before server sends its first "welcome" packet (e.g too many connections)
This was not taken into account originally in MDEV-19893 fix.

We need to check sql_errno, before fixing sequence number, to see
if the error we send is really an out-of-bound, e.g a KILL.

MDEV-25201 : Assertion `thd->wsrep_trx_meta.gtid.seqno == (-1)' failed in int wsrep_to_isolation_begin(THD*, const char*, const char*, const TABLE_LIST*, Alter_info*)

Test case does not assert anymore but works incorrectly. We should
not replicate PREPARE using TOI.

is connected so moved test here.

MDEV-25549 : Assertion `*new_engine' failed in bool check_engine(THD*, const char*, const char*, HA_CREATE_INFO*)

In Galera case we call check_engine that could set create_info->db_type
to NULL e.g. if TEMPORARY is not supported by storage engine. Thus,
we need to restore it after that call because it is needed later
on mysql_create_table that will also call check_engine.

For MERGE-tables we need to init children list before calling
show_create_table and then detach children before we continue
normal mysql_create_like_table execution.

MDEV-25472 : Server crashes when wsrep_cluster_address set to unkown address and wsrep_slave_threads to 0

Return failure if we are not connected when slave threads are set

MDEV-20325: Assertion `outer_context || !*from_field || *from_field == not_found_field' failed in Item_field::fix_outer_field | `!derived->is_excluded()' failed in TABLE_LIST::set_check_materialized | SIGEGV in st_select_lex::mark_as_dependent (optimized builds)

Re-execution of a query containing subquery in the FROM clause results
in assert failure in case the query is run as part of a stored routine or
as a prepared statement AND derived table merge optimization is off.
As an example, the following test case
  CREATE TABLE t1 (a INT) ;
  CREATE PROCEDURE sp() SELECT * FROM (SELECT a FROM t1) tb;
  CALL sp();
  SET optimizer_switch='derived_merge=off';
  CALL sp();
results in assert failure on the second invocation of the 'sp' stored routine.

The reason for assertion failure is that the expression
  derived->is_excluded()
returns the value true where the value false expected.

The method is_excluded() returns the value true for a derived table
that has been merged to a parent select. Such transformation happens as part
of Derived Table Merge Optimization that is performed on first invocation of
a stored routine or a prepared statement containing a query with subquery
in the FROM clause of the main SELECT.

When the same routine or prepared statement is run the second time and
Derived Table Merge Optimization is OFF the MariaDB server tries to materialize
a derived table specified by the subquery that fails since this subquery
has already been merged to the top-most SELECT. This transformation is permanent
and can't be reverted. That is the reason why the assert
  DBUG_ASSERT(!derived->is_excluded());
fails inside the function TABLE_LIST::set_check_materialized().

Similar behaviour can be observed in case a stored routine or prepared statement
containing a SELECT statement with subquery in the FROM clause, first is run
with the optimizer_switch option set to derived_merge=off and re-run after this
option has been switched to derived_merge=on. In this case a derived table for
subquery is materialized on the first execution and marked as merged derived
table on the second execution that results in error with misleading error
message:

MariaDB [test]> CALL sp1();
ERROR 1030 (HY000): Got error 1 "Operation not permitted" from storage engine MEMORY

To fix the issue, a derived table that has been already optimized shouldn't be
re-marked for one more round of optimization.

One significant consequence following from suggested change is that the data
member TABLE_LIST::derived_type is not updated once the table optimization
has been done. This fact should be taken into account when Prepared Statement
being handled since once a table listed in a query has been optimized on
execution of the statement PREPARE FROM it won't be touched anymore on handling
the statement EXECUTE.

One side effect caused by this change could be observed for the following
test case:
  CREATE TABLE t1 (s1 INT);
  CREATE VIEW v1 AS
    SELECT s1,s2 FROM (SELECT s1 as s2 FROM t1 WHERE s1 <100) x, t1 WHERE t1.s1=x.s2;
  INSERT INTO v1 (s1) VALUES (-300);

  PREPARE stmt FROM "INSERT INTO v1 (s1) VALUES (-300)";
  EXECUTE stmt;

Execution of the above EXECUTE statement results in issuing the error
ER_COLUMNACCESS_DENIED_ERROR since table_ref->is_merged_derived() is false
and check_column_grant_in_table_ref() called for a temporary table that
shouldn't be. To fix this issue the function find_field_in_tables has been
modified in such a way that the function check_column_grant_in_table_ref()
is not called for a temporary table.

This bug could cause a crash of the server for queries with a derived table
whose specification contained the set function using a subquery over a view
as its only argument. The crash could happen if the specification of the
view contained an outer reference. In this case the aggregation select
could be determined incorrectly.
The crash also could be observed if a CTE is used instead of the view, but
only for queries having at least two references to the CTE.

The cause of this bug is the same as of the bug MDEV-24454.
This bug manifested itself at the second execution of the queries that
contained a set function whose only argument was outer reference to
a column of a mergeable view or derived table or CTE. The first execution
of such query worked fine, but the second execution of the query caused
a crash of the server because the aggregation select for the used set
function was determined incorrectly at the name resolution phase of the
second execution.

This patch reverts the fixes of the bugs MDEV-24454 and MDEV-25631 from
the commit 3690c549.
It leaves the changes in plugin/feedback/feedback.cc and corresponding
test files introduced in this commit intact.

Proper fixes for the bug MDEV-24454 and MDEV-25631 will follow immediately.

The bug that made build stuck in bison call seems to have disappeared
with image update

allow injecting extra files into the bintar

Problem:
========
A slave’s relay log format description event is used when
calculating Seconds_Behind_Master (SBM). This forces the SBM
value to spike when processing these events, as their creation
date is set to the timestamp that the IO thread begins.

Solution:
========
When the slave generates a format description event, mark the
event as a relay log event so it does not update the
rli->last_master_timestamp variable.

Reviewed By:
============
Andrei Elkin <andrei.elkin@mariadb.com>

table: rows are counted twice

Analysis: When the table we are trying to insert into and the SELECT table
are same for INSERT ... SELECT, rows from the SELECT table are copied into
internal temporary table and then to the INSERT table. We only want to
count the rows when we start inserting into the table.
Fix: Reset the counter to 1 before starting to copy from internal temporary
table to select table and then increment the counter.

... when two packages are installed.

(fc35 with i686 and x86_64 packages of libsepol installed).
$ rpm -q --qf "%{VERSION}" libsepol
3.33.3

Restricting the version to the current achitecture generates
a much more obtainable version dependency.

$ rpm -q --qf "%{VERSION}" libsepol.x86_64
3.3

This make dependency resolution easier preventing:
$ sudo dnf localinstall  MariaDB-server-10.8.0-1.fc35.x86_64.rpm ...
Last metadata expiration check: 2:06:49 ago on Thu 30 Dec 2021 14:02:32.
Error:
 Problem 1: conflicting requests
  - nothing provides libsepol >= 3.33.3 needed by MariaDB-server-10.8.0-1.fc35.x86_64

The CMAKE_SYSTEM_PROCESSOR is used in the generation of architecture
filenames so its preduent to just use the same version.

Adding 10.2 specific tests only. No code changes.

The problem was earlier fixed by MDEV-21580 and MDEV-22715.

The problem happened because Item_default_value did not overload
properly the val_xxx_result() family methods.

This change backports the patch for:
MDEV-24958 Server crashes in my_strtod / Value_source::Converter_strntod::Converter_strntod with DEFAULT(blob)
which earlier fixed the problem in 10.3.

failed in Diagnostics_area::set_ok_status in my_ok from
mysql_sql_stmt_prepare

Analysis: Before PREPARE is executed, binlog_format is STATEMENT.
This PREPARE had SET STATEMENT which sets binlog_format to ROW. Now after
PREPARE is done we reset the binlog_format (back to STATEMENT). But we have
temporary table, it doesn't let changing binlog_format=ROW to
binlog_format=STATEMENT and gives error which goes unreported. This
unreported error eventually causes assertion failure.
Fix: Change return type for LEX::restore_set_statement_var() to bool and
make it return error state.

MDEV-27364 Build from 10.2-10.4 srpm fails on RHEL8 family due to discrepancy in jemalloc requirements

pass jemalloc requirement down to srpm build

If when extracting a range condition for an index from the WHERE condition
Range Optimizer sees that the range condition covers the whole index then
such condition should be discarded because it cannot be used in any range
scan. In some cases Range Optimizer really does it, but there remained some
conditions for which it was not done. As a result the optimizer could
produce index merge plans with the full index scan for one of the indexes
participating in the index merge.
This could be observed in one of the test cases from index_merge1.inc
where a plan with index_merge_sort_union was produced and in the test case
reported for this bug where a plan with index_merge_sort_intersect was
produced. In both cases one of two index scans participating in index merge
ran over the whole index.
The patch slightly changes the original above mentioned test case from
index_merge1.inc to be able to produce an intended plan employing
index_merge_sort_union. The original query was left to show that index
merge is not used for it anymore.
It should be noted that for the plan with index_merge_sort_intersect could
be chosen for execution only due to a defect in the InnoDB code that
returns wrong estimates for the cardinality of big ranges.

This bug led to serious problems in 10.4+ where the optimization using
Rowid filters is employed (see mdev-26446).

Approved by Sergey Petrunia <sergey@mariadb.com>

This is the first part of the fixes for MDEV-24097. This commit
contains the fixes for instability when testing Galera and when
restarting nodes quickly:

1) Protection against a "stuck" old SST process during the execution
   of the new SST (after restarting the node) is now implemented for
   mariabackup / xtrabackup, which should help to avoid almost all
   conflicts due to the use of the same ports - both during testing
   with mtr, so and when restarting nodes quickly in a production
   environment.
2) Added more protection to scripts against unexpected return of
   the rc != 0 (in the commands for deleting temporary files, etc).
3) Added protection against unexpected crashes during binlog transfer
   (in SST scripts for rsync).
4) Spaces and some special characters in binlog filenames shouldn't
   be a problem now (at the script level).
5) Daemon process termination tracking has been made more robust
   against crashes due to unexpected termination of the previous SST
   process while new scripts are running.
6) Reading ssl encryption parameters has been moved from specific
   SST scripts to a common wsrep_sst_common.sh script, which allows
   unified error handling, unified diagnostics and simplifies script
   revisions in the future.
7) Improved diagnostics of errors related to the use of openssl.
8) Corrections have been made for xtrabackup-v2 (both in tests and in
   the script code) that restore the work of xtrabackup with updated
   versions of innodb.
9) Fixed some tests for galera_3nodes, although the complete solution
   for the problem of starting three nodes at the same time on fast
   machines will be done in a separate commit.

No additional tests are required as this commit fixes problems with
existing tests.

Small postfix to MDEV-23175 to ensure faster option on FreeBSD
and compatibility to Solaris that isn't high resolution.

ftime is left as a backup in case an implementation doesn't
contain any of these clocks.

FreeBSD
    $ ./unittest/mysys/my_rdtsc-t
    1..11
    # ----- Routine ---------------
    # myt.cycles.routine          :             5
    # myt.nanoseconds.routine     :            11
    # myt.microseconds.routine    :            13
    # myt.milliseconds.routine    :            11
    # myt.ticks.routine           :            17
    # ----- Frequency -------------
    # myt.cycles.frequency        :    3610295566
    # myt.nanoseconds.frequency   :    1000000000
    # myt.microseconds.frequency  :       1000000
    # myt.milliseconds.frequency  :           899
    # myt.ticks.frequency         :           136
    # ----- Resolution ------------
    # myt.cycles.resolution       :             1
    # myt.nanoseconds.resolution  :             1
    # myt.microseconds.resolution :             1
    # myt.milliseconds.resolution :             7
    # myt.ticks.resolution        :             1
    # ----- Overhead --------------
    # myt.cycles.overhead         :            26
    # myt.nanoseconds.overhead    :         19140
    # myt.microseconds.overhead   :         19036
    # myt.milliseconds.overhead   :           578
    # myt.ticks.overhead          :         21544
    ok 1 - my_timer_init() did not crash
    ok 2 - The cycle timer is strictly increasing
    ok 3 - The cycle timer is implemented
    ok 4 - The nanosecond timer is increasing
    ok 5 - The nanosecond timer is implemented
    ok 6 - The microsecond timer is increasing
    ok 7 - The microsecond timer is implemented
    ok 8 - The millisecond timer is increasing
    ok 9 - The millisecond timer is implemented
    ok 10 - The tick timer is increasing
    ok 11 - The tick timer is implemented

1) Removed symlinks that are not very well supported in tar under Windows.
2) Added comment + changed code formatting in viosslfactories.c
3) Fixed a small bug in the yassl code.
4) Fixed a typo in the script code.

Consider the following use case:
MariaDB [test]> CREATE TABLE t1 (field1 BIGINT DEFAULT -1);
MariaDB [test]> CREATE VIEW v1 AS SELECT DISTINCT field1 FROM t1;

Repeated execution of the following query as a Prepared Statement

MariaDB [test]> PREPARE stmt FROM 'SELECT * FROM v1 WHERE field1 <=> NULL';
MariaDB [test]> EXECUTE stmt;

results in a crash for a server built with DEBUG.

MariaDB [test]> EXECUTE stmt;
ERROR 2013 (HY000): Lost connection to MySQL server during query

Assertion failed: (!result), function convert_const_to_int, file item_cmpfunc.cc, line 476.
Abort trap: 6 (core dumped)

The crash inside the function convert_const_to_int() happens by the reason
that the value -1 is stored in an instance of the class Field_longlong
on restoring its original value in the statement
  result= field->store(orig_field_val, TRUE);
that leads to assigning the value 1 to the variable 'result' with subsequent
crash in the DBUG_ASSERT statement following it
  DBUG_ASSERT(!result);

The main matter here is why this assertion failure happens on the second
execution of the prepared statement and doens't on the first one.
On first handling of the statement
  'EXECUTE stmt;'
a temporary table is created for serving the query involving the view 'v1'.
The table is created by the function create_tmp_table() in the following
calls trace: (trace #1)
  JOIN::prepare (at sql_select.cc:725)
    st_select_lex::handle_derived
      LEX::handle_list_of_derived
        TABLE_LIST::handle_derived
          mysql_handle_single_derived
            mysql_derived_prepare
              select_union::create_result_table
                create_tmp_table

Note, that the data member TABLE::status of a TABLE instance returned by the
function create_tmp_table() has the value 0.

Later the function setup_table_map() is called on the TABLE instance just
created for the sake of the temporary table (calls trace #2 is below):
  JOIN::prepare (at sql_select.cc:737)
    setup_tables_and_check_access
      setup_tables
        setup_table_map
where the data member TABLE::status is set to the value STATUS_NO_RECORD.

After that when execution of the method JOIN::prepare reaches calling of
the function setup_without_group() the following calls trace is invoked
  JOIN::prepare
    setup_without_group
      setup_conds
        Item_func::fix_fields
          Item_func_equal::fix_length_and_dec
            Item_bool_rowready_func2::fix_length_and_dec
              Item_func::setup_args_and_comparator
                Item_func::convert_const_compared_to_int_field
                  convert_const_to_int

There is the following code snippet in the function convert_const_to_int()
at the line item_cmpfunc.cc:448
    bool save_field_value= (field_item->const_item() ||
                            !(field->table->status & STATUS_NO_RECORD));
Since field->table->status has bits STATUS_NO_RECORD set the variable
save_field_value is false and therefore neither the method
Field_longlong::val_int() nor the method Field_longlong::store is called
on the Field instance that has the numeric value -1.
That is the reason why first execution of the Prepared Statement for the query
  'SELECT * FROM v1 WHERE field1 <=> NULL'
is successful.

On second running of the statement 'EXECUTE stmt' a new temporary tables
is also created by running the calls trace #1 but the trace #2 is not executed
by the reason that data member SELECT_LEX::first_cond_optimization has been set
to false on first execution of the prepared statemet (in the method
JOIN::optimize_inner()). As a consequence, the data member TABLE::status for
a temporary table just created doesn't have the flags STATUS_NO_RECORD set and
therefore on re-execution of the prepared statement the methods
Field_longlong::val_int() and Field_longlong::store() are called for the field
having the value -1 and the DBUG_ASSERT(!result) is fired.

To fix the issue the data member TABLE::status has to be assigned the value
STATUS_NO_RECORD in every place where the macros empty_record() is called
to emptify a record for just instantiated TABLE object created on behalf
the new temporary table.

Followup to fix for MDEV-25858: When test_if_skip_sort_order() decides
to use an index to satisfy ORDER BY ... LIMIT clause, it should
disable "Range Checked for Each Record" optimization.

Do this in all cases.

* galera_pc_bootstrap
* galera_ipv6_mariabackup
* galera_ipv6_mariabackup_section
* galera_ipv6_rsync
* galera_ipv6_rsync_section
* galera_ssl_reload
* galera_toi_vote
* galera_wsrep_schema_init

because MTR sporadaically fails: Failed to start mysqld or mysql_shutdown failed

create_log_files(): Check log_set_capacity() before modifying
or creating any log files.

innobase_start_or_create_for_mysql(): If create_log_files()
fails and we were initializing a new database, delete the
system tablespace files before exiting.