NXP has developed software support in the MC firmware, and Linux to
reconfigure serdes speed dynamically between 10G and 25G protocols
(USXGMII/CAUI).
Backport the provided patches to work with our LSDK-21.08 fork.

Requires python version

Fixes: e89f4ca6 clearfog-cx/honeycomb: add support for serdes 1 protocol 20 (2x 40G)

After changes to serdes driver and rcw, add the missing device-tree
descriptions to allow dpmac driver to probe again.

add docker support per https://community.solid-run.com/t/building-a-docker-enabled-kernel-for-the-solidrun/379

Note that the QSFP can not work in this configuration as the retimer
only supports 10/25 frequencies.

The new(er) FW enables switching between 1&10Gbps speed on SFP
connector, **only if the COM has PLLF/PLLS swapped**.

- focal (default)
- jammy

Change the ip configuration for the temporary VM to be performed
directly by the kernel; then copy the kernel reported resolv config to
rootfs + chroot.

This will avoid firewall issues that may be experienced in paranoid
homes, or coprorate networks where direct access to public DNS servers
is not allowed.

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Add the necessary setup code to dpaa2-eth driver for controlling
link-status leds from the mac driver.
Signed-off-by: Josua Mayer <josua@solid-run.com>

To allow reliable link-status indication when exporting native
interfaces to dpdk, add support for controlling an LED to dpmac driver
link up- and down- functions.

Note that this is a hack and not a proper solution - with its own
particular shortcomings. Most notable is the lack of status indication
while Linux is controlling the interface through the dpaa2 ethernet
driver!
Signed-off-by: Josua Mayer <josua@solid-run.com>

LX2162A Clearfog support only covers 8x 1G rj45 + 2x 10G fixed-link sfp.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Note: To utilize this configuration DPL and DPC must be changed
accordingly to enable dpmac 13+14 for sgmii.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

make modules_install will not generate the module dependencies file if
the depmod command is missing from the running system.
Add it as a requirement to runme.sh and include in Dockerfile.
Signed-off-by: Josua Mayer <josua@solid-run.com>