MC firmware 10.36 requires adding "compatible" properties to DPL.
Update all DPLs accordingly.

In Linux we can by default see 2 LEDs - mmc:0, mmc:1 - created in
/sys/class/leds/. This is unexpected for 2 reasons:

1. LX2160A has no mention of mmc led functionality for the pads
2. LX2160A reference manual describes the relevant bit in control
   register as reserved.

Enable SDHCI_QUIRK_NO_LED for LX2160A.

This configuration enables both:
- 4x SFP (2x switching between 10/25G)
- 8x RJ45 @1Gbps each

Note that DPL and MC FW have been updated from problematic 10.32.0.

10.32 has proven unreliable for dpmac 15, 16 & 18.
Upgrade to 10.36 (latest) release which is working well.

Ensure to choose serdes 1 protocol 18 to enable support for 25Gbpps on 2
of the SFP+ connectors. The other 2 do not have a retimer and will
likely have bad signal integrity if used at 25Gbpbs.

NXP has developed software support in the MC firmware, and Linux to
reconfigure serdes speed dynamically between 10G and 25G protocols
(USXGMII/CAUI).
Backport the provided patches to work with our LSDK-21.08 fork.

Requires python version

Fixes: e89f4ca6 clearfog-cx/honeycomb: add support for serdes 1 protocol 20 (2x 40G)

After changes to serdes driver and rcw, add the missing device-tree
descriptions to allow dpmac driver to probe again.

add docker support per https://community.solid-run.com/t/building-a-docker-enabled-kernel-for-the-solidrun/379

Note that the QSFP can not work in this configuration as the retimer
only supports 10/25 frequencies.

The new(er) FW enables switching between 1&10Gbps speed on SFP
connector, **only if the COM has PLLF/PLLS swapped**.

- focal (default)
- jammy

Change the ip configuration for the temporary VM to be performed
directly by the kernel; then copy the kernel reported resolv config to
rootfs + chroot.

This will avoid firewall issues that may be experienced in paranoid
homes, or coprorate networks where direct access to public DNS servers
is not allowed.

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Add the necessary setup code to dpaa2-eth driver for controlling
link-status leds from the mac driver.
Signed-off-by: Josua Mayer <josua@solid-run.com>

To allow reliable link-status indication when exporting native
interfaces to dpdk, add support for controlling an LED to dpmac driver
link up- and down- functions.

Note that this is a hack and not a proper solution - with its own
particular shortcomings. Most notable is the lack of status indication
while Linux is controlling the interface through the dpaa2 ethernet
driver!
Signed-off-by: Josua Mayer <josua@solid-run.com>

LX2162A Clearfog support only covers 8x 1G rj45 + 2x 10G fixed-link sfp.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>