*** empty log message ***

xtt/mmi/xtt/en_us/xtt_lng.dat

@@ -315,11 +315,23 @@ B 5.2.5 "Power in not on, "
 # ABB_Sensor_Pb_PA
 B 5.3.1 "Transmitter error, value cannot be used, "
 B 5.3.2 "Transmitter warning, value uncertain, "
+B 5.3.3 "Non-specific error, "
+B 5.3.4 "Configuration error, "
+B 5.3.5 "Not connected, "
+B 5.3.6 "Device fail, "
+B 5.3.7 "Sensor fail, "
+B 5.3.8 "Last usable value, "
+B 5.3.9 "No usable value, "
+B 5.3.10 "Out of service, "
+B 5.3.11 "Substitute set, "
+B 5.3.12 "Initail value, "
+B 5.3.13 "Sensor conversion not accurate, "
+B 5.3.14 "Engineering unit violation, "
+B 5.3.15 "Sub-normal, "
+B 5.3.16 "Simulated value, "
+B 5.3.17 "Sensor calibration, "
 # ABB_TempSensor_TF12Fo
-B 5.4.1 "Sensor break, "
-B 5.4.2 "Sensor short circuit, "
-B 5.4.3 "Value below measuring range, "
-B 5.4.4 "Value exceed measuring range, "
+B 5.4.1 "Temp sensor"
 # ABB_DiffpressureSensor_265dsFo
 B 5.5.1 "Diffpressure"
 B 5.5.2 "Static pressure"

xtt/mmi/xtt/sv_se/xtt_lng.dat

@@ -310,11 +310,23 @@ B 5.2.5 "Effekt/Kontaktor ej till, "
 # ABB_Sensor_Pb_PA
 B 5.3.1 "Omvandlarfel, vrdet kan inte anvndas, "
 B 5.3.2 "Omvandlarvarning, vrdet oskert, "
+B 5.3.3 "Ej specifierat fel, "
+B 5.3.4 "Konfigurationsfel, "
+B 5.3.5 "Ej ansluten, "
+B 5.3.6 "Apparatfel, "
+B 5.3.7 "Givarfel, "
+B 5.3.8 "Lst till senast anvndbara vrdet, "
+B 5.3.9 "Inget anvndbart vrde, "
+B 5.3.10 "Ur funktion, "
+B 5.3.11 "Ersttningsomrde, "
+B 5.3.12 "Startvrde, "
+B 5.3.13 "Omvandling ej korrekt, "
+B 5.3.14 "Vrde utanfr mtomrdet, "
+B 5.3.15 "Ej normalt mtomrde, "
+B 5.3.16 "Simulerat vrde, "
+B 5.3.17 "Givarkalibrering, "
 # ABB_TempSensor_TF12Fo
-B 5.4.1 "Avbrott i givare, "
-B 5.4.2 "Kortslutning i givare, "
-B 5.4.3 "Vrdet under givarens mtomrde, "
-B 5.4.4 "Vrdet ver givarens mtomrde, "
+B 5.4.1 "Temperaturgivare, "
 # ABB_DiffpressureSensor_265dsFo
 B 5.5.1 "Difftryck"
 B 5.5.2 "Statiskt tryck"