This command should only be used if remote device reports that it
supports extended features. Otherwise command will fail and connection
will be dropped.

Some devices support SSP but don't support extended features so
current check for SSP support is not enought.

Instead of checking for SSP support just check if both ends support
Extended Feature.

< HCI Command: Create Connection (0x01|0x0005) plen 13
        Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited)
        Packet type: 0xcc18
          DM1 may be used
          DH1 may be used
          DM3 may be used
          DH3 may be used
          DM5 may be used
          DH5 may be used
        Page scan repetition mode: R1 (0x01)
        Page scan mode: Mandatory (0x00)
        Clock offset: 0x94c8
        Role switch: Allow slave (0x01)
> HCI Event: Command Status (0x0f) plen 4
      Create Connection (0x01|0x0005) ncmd 1
        Status: Success (0x00)
> HCI Event: Connect Complete (0x03) plen 11
        Status: Success (0x00)
        Handle: 5
        Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited)
        Link type: ACL (0x01)
        Encryption: Disabled (0x00)
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
        Handle: 5
> HCI Event: Command Status (0x0f) plen 4
      Read Remote Supported Features (0x01|0x001b) ncmd 1
        Status: Success (0x00)
> HCI Event: Page Scan Repetition Mode Change (0x20) plen 7
        Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited)
        Page scan repetition mode: R1 (0x01)
> HCI Event: Read Remote Supported Features (0x0b) plen 11
        Status: Success (0x00)
        Handle: 5
        Features: 0xff 0xff 0x8f 0xfe 0xdb 0xff 0x5b 0x07
          3 slot packets
          5 slot packets
          Encryption
          Slot offset
          Timing accuracy
          Role switch
          Hold mode
          Sniff mode
          Park state
          Power control requests
          Channel quality driven data rate (CQDDR)
          SCO link
          HV2 packets
          HV3 packets
          u-law log synchronous data
          A-law log synchronous data
          CVSD synchronous data
          Paging parameter negotiation
          Power control
          Transparent synchronous data
          Broadcast Encryption
          Enhanced Data Rate ACL 2 Mbps mode
          Enhanced Data Rate ACL 3 Mbps mode
          Enhanced inquiry scan
          Interlaced inquiry scan
          Interlaced page scan
          RSSI with inquiry results
          Extended SCO link (EV3 packets)
          EV4 packets
          EV5 packets
          AFH capable slave
          AFH classification slave
          LE Supported (Controller)
          3-slot Enhanced Data Rate ACL packets
          5-slot Enhanced Data Rate ACL packets
          Sniff subrating
          Pause encryption
          AFH capable master
          AFH classification master
          Enhanced Data Rate eSCO 2 Mbps mode
          Enhanced Data Rate eSCO 3 Mbps mode
          3-slot Enhanced Data Rate eSCO packets
          Extended Inquiry Response
          Simultaneous LE and BR/EDR (Controller)
          Secure Simple Pairing
          Encapsulated PDU
          Non-flushable Packet Boundary Flag
          Link Supervision Timeout Changed Event
          Inquiry TX Power Level
          Enhanced Power Control
< HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3
        Handle: 5
        Page: 1
> HCI Event: Command Status (0x0f) plen 4
      Read Remote Extended Features (0x01|0x001c) ncmd 1
        Status: Command Disallowed (0x0c)
< HCI Command: Read Clock Offset (0x01|0x001f) plen 2
        Handle: 5
> HCI Event: Command Status (0x0f) plen 4
      Read Clock Offset (0x01|0x001f) ncmd 1
        Status: Success (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 5
        Reason: Remote User Terminated Connection (0x13)
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>