With the LSI FW643 rev 8 [1], the first commanded bus reset at
the conclusion of ohci_enable() has been observed to fail with
the following messages:

[    4.884015] firewire_ohci 0000:01:00.0: failed to read phy reg
....
[    5.684012] firewire_ohci 0000:01:00.0: failed to read phy reg

With drivers/firewire/ohci.c instrumented, the error condition [2]
indicates the PHY arbitration state machine has timed out prior to
enabling PHY LCtrl.

Furthermore, instrumenting ohci_enable() shows that LPS has been
enabled within 1 ms.

Test LPS latching every 1 ms rather than every 50ms.

[1]  lspci -v

01:00.0 FireWire (IEEE 1394): LSI Corporation FW643 [TrueFire] PCIe 1394b Controller (rev 08) (prog-if 10 [OHCI])
	Subsystem: LSI Corporation FW643 [TrueFire] PCIe 1394b Controller
	Flags: bus master, fast devsel, latency 0, IRQ 92
	Memory at fbeff000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 3
	Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Capabilities: [60] Express Endpoint, MSI 00
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [170] Device Serial Number 08-14-43-82-00-00-41-fc
	Kernel driver in use: firewire_ohci
	Kernel modules: firewire-ohci

[2] instrumented WARNING in read_phy_reg()

[    4.576010] ------------[ cut here ]------------
[    4.576035] WARNING: at ./drivers/firewire/ohci.c:570 read_phy_reg+0x93/0xe0 [firewire_ohci]()
[    4.576050] Hardware name: Precision WorkStation T5400
[    4.576058] failed to read phy reg:1 (phy(5) @ config enhance:19)
[    4.576068] Modules linked in: hid_logitech_dj hid_generic(+) usbhid <...snip...>
[    4.576140] Pid: 61, comm: kworker/2:1 Not tainted 3.8.0-2+fwtest-xeon #2+fwtest
[    4.576149] Call Trace:
[    4.576160]  [<ffffffff8105468f>] warn_slowpath_common+0x7f/0xc0
[    4.576168]  [<ffffffff81054786>] warn_slowpath_fmt+0x46/0x50
[    4.576178]  [<ffffffffa00caca3>] read_phy_reg+0x93/0xe0 [firewire_ohci]
[    4.576188]  [<ffffffffa00cae19>] ohci_read_phy_reg+0x39/0x60 [firewire_ohci]
[    4.576203]  [<ffffffffa00731ff>] fw_send_phy_config+0xbf/0xe0 [firewire_core]
[    4.576214]  [<ffffffffa006b2d6>] br_work+0x46/0xb0 [firewire_core]
[    4.576225]  [<ffffffff81071e0c>] process_one_work+0x13c/0x500
[    4.576238]  [<ffffffffa006b290>] ? fw_card_initialize+0x180/0x180 [firewire_core]
[    4.576248]  [<ffffffff810737ed>] worker_thread+0x16d/0x470
[    4.576257]  [<ffffffff81073680>] ? busy_worker_rebind_fn+0x100/0x100
[    4.576266]  [<ffffffff8107d160>] kthread+0xc0/0xd0
[    4.576275]  [<ffffffff816a0000>] ? pcpu_dump_alloc_info+0x1cb/0x2c4
[    4.576284]  [<ffffffff8107d0a0>] ? kthread_create_on_node+0x130/0x130
[    4.576297]  [<ffffffff816b2f6c>] ret_from_fork+0x7c/0xb0
[    4.576305]  [<ffffffff8107d0a0>] ? kthread_create_on_node+0x130/0x130
[    4.576313] ---[ end trace cbc940994b300302 ]---

[Stefan R:  Peter also reports a change of behavior with LSI FW323.
Before the patch, there would often occur a lock transaction failure
during firewire-core startup:
[    6.056022] firewire_core 0000:07:06.0: BM lock failed (timeout), making local node (ffc0) root
This failure no longer happens after the patch, without an obvious
reason for the failure or the fix.]

[Stefan R:  Added quirk flag, quirk table entry, and comment.]
Reported-by: Tim Jordan <tim@insipid.org.uk>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>