-
Douglas Anderson authored
Back in the description of commit e440e30e ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at bootup on trogdor") we described a problem that we were seeing on trogdor devices. I'll re-summarize here but you can also re-read the original commit. On trogdor devices, the BIOS is setting up the SPI chip select as: - mux special function (SPI chip select) - output enable - output low (unused because we've muxed as special function) In the kernel, however, we've moved away from using the chip select line as special function. Since the kernel wants to fully control the chip select it's far more efficient to treat the line as a GPIO rather than sending packet-like commands to the GENI firmware every time we want the line to toggle. When we transition from how the BIOS had the pin configured to how the kernel has the pin configured we end up glitching the line. That's because we _first_ change the mux of the line and then later set its output. This glitch is bad and can confuse the device on the other end of the line. The old commit e440e30e ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at bootup on trogdor") fixed the glitch, though the solution was far from elegant. It essentially did the thing that everyone always hates: encoding a sequential program in device tree, even if it's a simple one. It also, unfortunately, got broken by commit b991f8c3 ("pinctrl: core: Handling pinmux and pinconf separately"). After that commit we did all the muxing _first_ even though the config (set the pin to output high) was listed first. :( I looked at ideas for how to solve this more properly. My first thought was to use the "init" pinctrl state. In theory the "init" pinctrl state is supposed to be exactly for achieving glitch-free transitions. My dream would have been for the "init" pinctrl to do nothing at all. That would let us delay the automatic pin muxing until the driver could set things up and call pinctrl_init_done(). In other words, my dream was: /* Request the GPIO; init it 1 (because DT says GPIO_ACTIVE_LOW) */ devm_gpiod_get_index(dev, "cs", GPIOD_OUT_LOW); /* Output should be right, so we can remux, yay! */ pinctrl_init_done(dev); Unfortunately, it didn't work out. The primary reason is that the MSM GPIO driver implements gpio_request_enable(). As documented in pinmux.h, that function automatically remuxes a line as a GPIO. ...and it does this remuxing _before_ specifying the output of the pin. You can see in gpiod_get_index() that we call gpiod_request() before gpiod_configure_flags(). gpiod_request() isn't passed any flags so it has no idea what the eventual output will be. We could have debates about whether or not the automatic remuxing to GPIO for the MSM pinctrl was a good idea or not, but at this point I think there is a plethora of code that's relying on it and I certainly wouldn't suggest changing it. Alternatively, we could try to come up with a way to pass the initial output state to gpio_request_enable() and plumb all that through. That seems like it would be doable, but we'd have to plumb it through several layers in the stack. This patch implements yet another alternative. Here, we specifically avoid glitching the first time a pin is muxed to GPIO function if the direction of the pin is output. The idea is that we can read the state of the pin before we set the mux and make sure that the re-mux won't change the state. NOTES: - We only do this the first time since later swaps between mux states might want to preserve the old output value. In other words, I wouldn't want to break a driver that did: gpiod_set_value(g, 1); pinctrl_select_state(pinctrl, special_state); pinctrl_select_default_state(); /* We should be driving 1 even if "special_state" made the pin 0 */ - It's safe to do this the first time since the driver _couldn't_ have explicitly set a state. In order to even be able to control the GPIO (at least using gpiod) we have to have requested it which would have counted as the first mux. - In theory, instead of keeping track of the first time a pin was set as a GPIO we could enable the glitch-free behavior only when msm_pinmux_request_gpio() is in the callchain. That works an enables my "dream" implementation above where we use an "init" state to solve this. However, it's nice not to have to do this. By handling just the first transition to GPIO we can simply let the normal "default" remuxing happen and we can be assured that there won't be a glitch. Before this change I could see the glitch reported on the EC console when booting. It would say this when booting the kernel: Unexpected state 1 in CSNRE ISR After this change there is no error reported. Note that I haven't reproduced the original problem described in e440e30e ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at bootup on trogdor") but I could believe it might happen in certain timing conditions. Fixes: b991f8c3 ("pinctrl: core: Handling pinmux and pinconf separately") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20221014103217.1.I656bb2c976ed626e5d37294eb252c1cf3be769dc@changeidSigned-off-by:
Linus Walleij <linus.walleij@linaro.org>
d21f4b7f