Commit 01a8ab4e authored by Arnd Bergmann's avatar Arnd Bergmann

Merge tag 'hisi-arm64-dt-for-5.1v2' of git://github.com/hisilicon/linux-hisi into arm/dt

ARM64: DT: Hisilicon SoCs DT updates for 5.1

* Hi6220 SoC and related boards:
  - Add DMA entries to enable DMA for Bluetooth transfers
  - Add power-on delay to make wifi stable
  - Revert HS200 mode to avoid eMMC controller resets and block read failures

* Hi3660 SoC and related boards:
  - Fix SD card detection via setting cd-gpios correctly

* Hi3798 SoC and related boards:
  - Fix malformed SPDX license identifier

* tag 'hisi-arm64-dt-for-5.1v2' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hikey: Revert "Enable HS200 mode on eMMC"
  arm64: dts: hikey: Give wifi some time after power-on
  arm64: dts: hi3798cv200: fix malformed SPDX license identifier
  arm64: dts: hikey960: fix SDcard detection
  arm64: dts: hikey: Add DMA entries for Bluetooth UART
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
parents f02635ea 8d26c139
......@@ -581,8 +581,7 @@ &dwmmc1 {
sd-uhs-sdr50;
sd-uhs-sdr104;
disable-wp;
cd-inverted;
cd-gpios = <&gpio25 3 0>;
cd-gpios = <&gpio25 3 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sd_pmx_func
&sd_clk_cfg_func
......
// SPDX-License-Identifier: GPL-2.0
/*
* DTS File for HiSilicon Poplar Development Board
*
* Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
*
* Released under the GPLv2 only.
* SPDX-License-Identifier: GPL-2.0
*/
/dts-v1/;
......
// SPDX-License-Identifier: GPL-2.0
/*
* DTS File for HiSilicon Hi3798cv200 SoC.
*
* Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
*
* Released under the GPLv2 only.
* SPDX-License-Identifier: GPL-2.0
*/
#include <dt-bindings/clock/histb-clock.h>
......
......@@ -118,6 +118,7 @@ wl1835_pwrseq: wl1835-pwrseq {
reset-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
clocks = <&pmic>;
clock-names = "ext_clock";
post-power-on-delay-ms = <10>;
power-off-delay-us = <10>;
};
......@@ -300,7 +301,6 @@ gpio15: gpio@f702b000 {
dwmmc_0: dwmmc0@f723d000 {
cap-mmc-highspeed;
mmc-hs200-1_8v;
non-removable;
bus-width = <0x8>;
vmmc-supply = <&ldo19>;
......
......@@ -319,6 +319,8 @@ uart1: uart@f7111000 {
clock-names = "uartclk", "apb_pclk";
pinctrl-names = "default";
pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func1 &uart1_cfg_func2>;
dmas = <&dma0 8 &dma0 9>;
dma-names = "rx", "tx";
status = "disabled";
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment