ARM: 5782/1: at91: support for eco920

CONFIG_MACH_ECO920 is enabled in at91rm9200dk_defconfig.  The name is
wrong, but this is better than adding another defconfig or don't get
compile coverage at all.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/configs/at91rm9200dk_defconfig

@@ -120,6 +120,7 @@ CONFIG_ARCH_AT91RM9200DK=y
 # CONFIG_MACH_CARMEVA is not set
 # CONFIG_MACH_KB9200 is not set
 # CONFIG_MACH_ATEB9200 is not set
+CONFIG_MACH_ECO920=y
 
 #
 # AT91RM9200 Feature Selections

arch/arm/mach-at91/Kconfig

@@ -163,6 +163,11 @@ config MACH_CPUAT91
 	  Select this if you are using the Eukrea Electromatique's
 	  CPUAT91 board <http://www.eukrea.com/>.
 
+config MACH_ECO920
+	bool "eco920"
+	help
+	  Select this if you are using the eco920 board
+
 endif
 
 # ----------------------------------------------------------

arch/arm/mach-at91/Makefile

@@ -35,6 +35,7 @@ obj-$(CONFIG_MACH_PICOTUX2XX)	+= board-picotux200.o
 obj-$(CONFIG_MACH_ECBAT91)	+= board-ecbat91.o
 obj-$(CONFIG_MACH_YL9200)	+= board-yl-9200.o
 obj-$(CONFIG_MACH_CPUAT91)	+= board-cpuat91.o
+obj-$(CONFIG_MACH_ECO920)	+= board-eco920.o
 
 # AT91SAM9260 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o

arch/arm/mach-at91/board-eco920.c

+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/board.h>
+#include <mach/at91rm9200_mc.h>
+#include "generic.h"
+
+static void __init eco920_map_io(void)
+{
+	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
+
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
+
+	/* DBGU on ttyS0. (Rx & Tx only */
+	at91_register_uart(0, 0, 0);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init eco920_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata eco920_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC2,
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata eco920_usbh_data = {
+	.ports		= 1,
+};
+
+static struct at91_udc_data __initdata eco920_udc_data = {
+	.vbus_pin	= AT91_PIN_PB12,
+	.pullup_pin	= AT91_PIN_PB13,
+};
+
+static struct at91_mmc_data __initdata eco920_mmc_data = {
+	.slot_b		= 0,
+	.wire4		= 0,
+};
+
+static struct physmap_flash_data eco920_flash_data = {
+	.width  = 2,
+};
+
+static struct resource eco920_flash_resource = {
+	.start          = 0x11000000,
+	.end            = 0x11ffffff,
+	.flags          = IORESOURCE_MEM,
+};
+
+static struct platform_device eco920_flash = {
+	.name           = "physmap-flash",
+	.id             = 0,
+	.dev            = {
+		.platform_data  = &eco920_flash_data,
+	},
+	.resource       = &eco920_flash_resource,
+	.num_resources  = 1,
+};
+
+static struct resource at91_beeper_resources[] = {
+	[0] = {
+		.start          = AT91RM9200_BASE_TC3,
+		.end            = AT91RM9200_BASE_TC3 + 0x39,
+		.flags          = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device at91_beeper = {
+	.name           = "at91_beeper",
+	.id             = 0,
+	.resource       = at91_beeper_resources,
+	.num_resources  = ARRAY_SIZE(at91_beeper_resources),
+};
+
+static struct spi_board_info eco920_spi_devices[] = {
+	{	/* CAN controller */
+		.modalias	= "tlv5638",
+		.chip_select	= 3,
+		.max_speed_hz	= 20 * 1000 * 1000,
+		.mode		= SPI_CPHA,
+	},
+};
+
+static void __init eco920_board_init(void)
+{
+	at91_add_device_serial();
+	at91_add_device_eth(&eco920_eth_data);
+	at91_add_device_usbh(&eco920_usbh_data);
+	at91_add_device_udc(&eco920_udc_data);
+
+	at91_add_device_mmc(0, &eco920_mmc_data);
+	platform_device_register(&eco920_flash);
+
+	at91_sys_write(AT91_SMC_CSR(7),	AT91_SMC_RWHOLD_(1)
+				| AT91_SMC_RWSETUP_(1)
+				| AT91_SMC_DBW_8
+				| AT91_SMC_WSEN
+				| AT91_SMC_NWS_(15));
+
+	at91_set_A_periph(AT91_PIN_PC6, 1);
+
+	at91_set_gpio_input(AT91_PIN_PA23, 0);
+	at91_set_deglitch(AT91_PIN_PA23, 1);
+
+/* Initialization of the Static Memory Controller for Chip Select 3 */
+	at91_sys_write(AT91_SMC_CSR(3),
+		AT91_SMC_DBW_16  |	/* 16 bit */
+		AT91_SMC_WSEN    |
+		AT91_SMC_NWS_(5) |	/* wait states */
+		AT91_SMC_TDF_(1)	/* float time */
+	);
+
+	at91_clock_associate("tc3_clk", &at91_beeper.dev, "at91_beeper");
+	at91_set_B_periph(AT91_PIN_PB6, 0);
+	platform_device_register(&at91_beeper);
+
+	at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
+}
+
+MACHINE_START(ECO920, "eco920")
+	/* Maintainer: Sascha Hauer */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= eco920_map_io,
+	.init_irq	= eco920_init_irq,
+	.init_machine	= eco920_board_init,
+MACHINE_END