Commit 01fed4c2 authored by Masakazu Mokuno's avatar Masakazu Mokuno Committed by Jeff Garzik

PS3: gelic: add support for port link status

Add support for interrupt driven port link status detection.
Signed-off-by: default avatarMasakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent 7bc56b92
......@@ -87,6 +87,28 @@ static inline void gelic_card_rx_irq_off(struct gelic_card *card)
{
gelic_card_set_irq_mask(card, card->ghiintmask & ~GELIC_CARD_RXINT);
}
static void
gelic_card_get_ether_port_status(struct gelic_card *card, int inform)
{
u64 v2;
struct net_device *ether_netdev;
lv1_net_control(bus_id(card), dev_id(card),
GELIC_LV1_GET_ETH_PORT_STATUS,
GELIC_LV1_VLAN_TX_ETHERNET, 0, 0,
&card->ether_port_status, &v2);
if (inform) {
ether_netdev = card->netdev;
if (card->ether_port_status & GELIC_LV1_ETHER_LINK_UP)
netif_carrier_on(ether_netdev);
else
netif_carrier_off(ether_netdev);
}
}
/**
* gelic_descr_get_status -- returns the status of a descriptor
* @descr: descriptor to look at
......@@ -1032,6 +1054,10 @@ static irqreturn_t gelic_card_interrupt(int irq, void *ptr)
gelic_card_kick_txdma(card, card->tx_chain.tail);
spin_unlock_irqrestore(&card->tx_dma_lock, flags);
}
/* ether port status changed */
if (status & GELIC_CARD_PORT_STATUS_CHANGED)
gelic_card_get_ether_port_status(card, 1);
return IRQ_HANDLED;
}
......@@ -1128,13 +1154,14 @@ static int gelic_net_open(struct net_device *netdev)
napi_enable(&card->napi);
card->tx_dma_progress = 0;
card->ghiintmask = GELIC_CARD_RXINT | GELIC_CARD_TXINT;
card->ghiintmask = GELIC_CARD_RXINT | GELIC_CARD_TXINT |
GELIC_CARD_PORT_STATUS_CHANGED;
gelic_card_set_irq_mask(card, card->ghiintmask);
gelic_card_enable_rxdmac(card);
netif_start_queue(netdev);
netif_carrier_on(netdev);
gelic_card_get_ether_port_status(card, 1);
return 0;
......@@ -1157,39 +1184,35 @@ static int gelic_ether_get_settings(struct net_device *netdev,
struct ethtool_cmd *cmd)
{
struct gelic_card *card = netdev_priv(netdev);
int status;
u64 v1, v2;
int speed, duplex;
speed = duplex = -1;
status = lv1_net_control(bus_id(card), dev_id(card),
GELIC_LV1_GET_ETH_PORT_STATUS,
GELIC_LV1_VLAN_TX_ETHERNET, 0, 0,
&v1, &v2);
if (status) {
/* link down */
} else {
if (v1 & GELIC_LV1_ETHER_FULL_DUPLEX) {
duplex = DUPLEX_FULL;
} else {
duplex = DUPLEX_HALF;
}
gelic_card_get_ether_port_status(card, 0);
if (v1 & GELIC_LV1_ETHER_SPEED_10) {
speed = SPEED_10;
} else if (v1 & GELIC_LV1_ETHER_SPEED_100) {
speed = SPEED_100;
} else if (v1 & GELIC_LV1_ETHER_SPEED_1000) {
speed = SPEED_1000;
}
if (card->ether_port_status & GELIC_LV1_ETHER_FULL_DUPLEX)
cmd->duplex = DUPLEX_FULL;
else
cmd->duplex = DUPLEX_HALF;
switch (card->ether_port_status & GELIC_LV1_ETHER_SPEED_MASK) {
case GELIC_LV1_ETHER_SPEED_10:
cmd->speed = SPEED_10;
break;
case GELIC_LV1_ETHER_SPEED_100:
cmd->speed = SPEED_100;
break;
case GELIC_LV1_ETHER_SPEED_1000:
cmd->speed = SPEED_1000;
break;
default:
pr_info("%s: speed unknown\n", __func__);
cmd->speed = SPEED_10;
break;
}
cmd->supported = SUPPORTED_TP | SUPPORTED_Autoneg |
SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full;
cmd->advertising = cmd->supported;
cmd->speed = speed;
cmd->duplex = duplex;
cmd->autoneg = AUTONEG_ENABLE; /* always enabled */
cmd->port = PORT_TP;
......
......@@ -261,6 +261,8 @@ struct gelic_card {
atomic_t tx_timeout_task_counter;
wait_queue_head_t waitq;
u64 ether_port_status;
struct gelic_descr *tx_top, *rx_top;
struct gelic_descr descr[0];
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment