Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
 "Just a bunch of fixes to squeeze in before -rc1:

   - three nouveau regression fixes

   - one qxl regression fix

   - a bunch of i915 fixes

  ... and some core displayport/atomic fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/device: enable c800 quirk for tecra w50
  drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
  drm/nouveau/gr/nv04: fix big endian setting on gr context
  drm/qxl: validate monitors config modes
  drm/i915: Allow DSI dual link to be configured on any pipe
  drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
  drm/i915: Fix CSR MMIO address check
  drm/i915: Limit the number of loops for reading a split 64bit register
  drm/i915: Fix broken mst get_hw_state.
  drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
  uapi/drm/i915_drm.h: fix userspace compilation.
  drm/i915: Always mark the object as dirty when used by the GPU
  drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
  drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
  drm/dp: Define AUX_RETRY_INTERVAL as 500 us
  drm/atomic: Fix bookkeeping with TEST_ONLY, v3.

drivers/gpu/drm/drm_atomic.c

@@ -1515,7 +1515,8 @@ int drm_mode_atomic_ioctl(struct drm_device *dev,
 			copied_props++;
 		}
 
-		if (obj->type == DRM_MODE_OBJECT_PLANE && count_props) {
+		if (obj->type == DRM_MODE_OBJECT_PLANE && count_props &&
+		    !(arg->flags & DRM_MODE_ATOMIC_TEST_ONLY)) {
 			plane = obj_to_plane(obj);
 			plane_mask |= (1 << drm_plane_index(plane));
 			plane->old_fb = plane->fb;
@@ -1537,10 +1538,11 @@ int drm_mode_atomic_ioctl(struct drm_device *dev,
 	}
 
 	if (arg->flags & DRM_MODE_ATOMIC_TEST_ONLY) {
+		/*
+		 * Unlike commit, check_only does not clean up state.
+		 * Below we call drm_atomic_state_free for it.
+		 */
 		ret = drm_atomic_check_only(state);
-		/* _check_only() does not free state, unlike _commit() */
-		if (!ret)
-			drm_atomic_state_free(state);
 	} else if (arg->flags & DRM_MODE_ATOMIC_NONBLOCK) {
 		ret = drm_atomic_async_commit(state);
 	} else {
@@ -1567,25 +1569,30 @@ int drm_mode_atomic_ioctl(struct drm_device *dev,
 		plane->old_fb = NULL;
 	}
 
+	if (ret && arg->flags & DRM_MODE_PAGE_FLIP_EVENT) {
+		/*
+		 * TEST_ONLY and PAGE_FLIP_EVENT are mutually exclusive,
+		 * if they weren't, this code should be called on success
+		 * for TEST_ONLY too.
+		 */
+
+		for_each_crtc_in_state(state, crtc, crtc_state, i) {
+			if (!crtc_state->event)
+				continue;
+
+			destroy_vblank_event(dev, file_priv,
+					     crtc_state->event);
+		}
+	}
+
 	if (ret == -EDEADLK) {
 		drm_atomic_state_clear(state);
 		drm_modeset_backoff(&ctx);
 		goto retry;
 	}
 
-	if (ret) {
-		if (arg->flags & DRM_MODE_PAGE_FLIP_EVENT) {
-			for_each_crtc_in_state(state, crtc, crtc_state, i) {
-				if (!crtc_state->event)
-					continue;
-
-				destroy_vblank_event(dev, file_priv,
-						     crtc_state->event);
-			}
-		}
-
+	if (ret || arg->flags & DRM_MODE_ATOMIC_TEST_ONLY)
 		drm_atomic_state_free(state);
-	}
 
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);

drivers/gpu/drm/drm_dp_helper.c

@@ -159,6 +159,8 @@ int drm_dp_bw_code_to_link_rate(u8 link_bw)
 }
 EXPORT_SYMBOL(drm_dp_bw_code_to_link_rate);
 
+#define AUX_RETRY_INTERVAL 500 /* us */
+
 /**
  * DOC: dp helpers
  *
@@ -213,7 +215,7 @@ static int drm_dp_dpcd_access(struct drm_dp_aux *aux, u8 request,
 			return -EIO;
 
 		case DP_AUX_NATIVE_REPLY_DEFER:
-			usleep_range(400, 500);
+			usleep_range(AUX_RETRY_INTERVAL, AUX_RETRY_INTERVAL + 100);
 			break;
 		}
 	}
@@ -422,6 +424,90 @@ static u32 drm_dp_i2c_functionality(struct i2c_adapter *adapter)
 	       I2C_FUNC_10BIT_ADDR;
 }
 
+#define AUX_PRECHARGE_LEN 10 /* 10 to 16 */
+#define AUX_SYNC_LEN (16 + 4) /* preamble + AUX_SYNC_END */
+#define AUX_STOP_LEN 4
+#define AUX_CMD_LEN 4
+#define AUX_ADDRESS_LEN 20
+#define AUX_REPLY_PAD_LEN 4
+#define AUX_LENGTH_LEN 8
+
+/*
+ * Calculate the duration of the AUX request/reply in usec. Gives the
+ * "best" case estimate, ie. successful while as short as possible.
+ */
+static int drm_dp_aux_req_duration(const struct drm_dp_aux_msg *msg)
+{
+	int len = AUX_PRECHARGE_LEN + AUX_SYNC_LEN + AUX_STOP_LEN +
+		AUX_CMD_LEN + AUX_ADDRESS_LEN + AUX_LENGTH_LEN;
+
+	if ((msg->request & DP_AUX_I2C_READ) == 0)
+		len += msg->size * 8;
+
+	return len;
+}
+
+static int drm_dp_aux_reply_duration(const struct drm_dp_aux_msg *msg)
+{
+	int len = AUX_PRECHARGE_LEN + AUX_SYNC_LEN + AUX_STOP_LEN +
+		AUX_CMD_LEN + AUX_REPLY_PAD_LEN;
+
+	/*
+	 * For read we expect what was asked. For writes there will
+	 * be 0 or 1 data bytes. Assume 0 for the "best" case.
+	 */
+	if (msg->request & DP_AUX_I2C_READ)
+		len += msg->size * 8;
+
+	return len;
+}
+
+#define I2C_START_LEN 1
+#define I2C_STOP_LEN 1
+#define I2C_ADDR_LEN 9 /* ADDRESS + R/W + ACK/NACK */
+#define I2C_DATA_LEN 9 /* DATA + ACK/NACK */
+
+/*
+ * Calculate the length of the i2c transfer in usec, assuming
+ * the i2c bus speed is as specified. Gives the the "worst"
+ * case estimate, ie. successful while as long as possible.
+ * Doesn't account the the "MOT" bit, and instead assumes each
+ * message includes a START, ADDRESS and STOP. Neither does it
+ * account for additional random variables such as clock stretching.
+ */
+static int drm_dp_i2c_msg_duration(const struct drm_dp_aux_msg *msg,
+				   int i2c_speed_khz)
+{
+	/* AUX bitrate is 1MHz, i2c bitrate as specified */
+	return DIV_ROUND_UP((I2C_START_LEN + I2C_ADDR_LEN +
+			     msg->size * I2C_DATA_LEN +
+			     I2C_STOP_LEN) * 1000, i2c_speed_khz);
+}
+
+/*
+ * Deterine how many retries should be attempted to successfully transfer
+ * the specified message, based on the estimated durations of the
+ * i2c and AUX transfers.
+ */
+static int drm_dp_i2c_retry_count(const struct drm_dp_aux_msg *msg,
+			      int i2c_speed_khz)
+{
+	int aux_time_us = drm_dp_aux_req_duration(msg) +
+		drm_dp_aux_reply_duration(msg);
+	int i2c_time_us = drm_dp_i2c_msg_duration(msg, i2c_speed_khz);
+
+	return DIV_ROUND_UP(i2c_time_us, aux_time_us + AUX_RETRY_INTERVAL);
+}
+
+/*
+ * FIXME currently assumes 10 kHz as some real world devices seem
+ * to require it. We should query/set the speed via DPCD if supported.
+ */
+static int dp_aux_i2c_speed_khz __read_mostly = 10;
+module_param_unsafe(dp_aux_i2c_speed_khz, int, 0644);
+MODULE_PARM_DESC(dp_aux_i2c_speed_khz,
+		 "Assumed speed of the i2c bus in kHz, (1-400, default 10)");
+
 /*
  * Transfer a single I2C-over-AUX message and handle various error conditions,
  * retrying the transaction as appropriate.  It is assumed that the
@@ -434,13 +520,16 @@ static int drm_dp_i2c_do_msg(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg)
 {
 	unsigned int retry, defer_i2c;
 	int ret;
-
 	/*
 	 * DP1.2 sections 2.7.7.1.5.6.1 and 2.7.7.1.6.6.1: A DP Source device
 	 * is required to retry at least seven times upon receiving AUX_DEFER
 	 * before giving up the AUX transaction.
+	 *
+	 * We also try to account for the i2c bus speed.
 	 */
-	for (retry = 0, defer_i2c = 0; retry < (7 + defer_i2c); retry++) {
+	int max_retries = max(7, drm_dp_i2c_retry_count(msg, dp_aux_i2c_speed_khz));
+
+	for (retry = 0, defer_i2c = 0; retry < (max_retries + defer_i2c); retry++) {
 		mutex_lock(&aux->hw_mutex);
 		ret = aux->transfer(aux, msg);
 		mutex_unlock(&aux->hw_mutex);
@@ -476,7 +565,7 @@ static int drm_dp_i2c_do_msg(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg)
 			 * For now just defer for long enough to hopefully be
 			 * safe for all use-cases.
 			 */
-			usleep_range(500, 600);
+			usleep_range(AUX_RETRY_INTERVAL, AUX_RETRY_INTERVAL + 100);
 			continue;
 
 		default:
@@ -506,7 +595,7 @@ static int drm_dp_i2c_do_msg(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg)
 			aux->i2c_defer_count++;
 			if (defer_i2c < 7)
 				defer_i2c++;
-			usleep_range(400, 500);
+			usleep_range(AUX_RETRY_INTERVAL, AUX_RETRY_INTERVAL + 100);
 			continue;
 
 		default:

drivers/gpu/drm/i915/i915_drv.h

@@ -1929,6 +1929,8 @@ struct drm_i915_private {
 			struct skl_wm_values skl_hw;
 			struct vlv_wm_values vlv;
 		};
+
+		uint8_t max_level;
 	} wm;
 
 	struct i915_runtime_pm pm;
@@ -3384,13 +3386,13 @@ int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
 #define I915_READ64(reg)	dev_priv->uncore.funcs.mmio_readq(dev_priv, (reg), true)
 
 #define I915_READ64_2x32(lower_reg, upper_reg) ({			\
-	u32 upper, lower, tmp;						\
-	tmp = I915_READ(upper_reg);					\
+	u32 upper, lower, old_upper, loop = 0;				\
+	upper = I915_READ(upper_reg);					\
 	do {								\
-		upper = tmp;						\
+		old_upper = upper;					\
 		lower = I915_READ(lower_reg);				\
-		tmp = I915_READ(upper_reg);				\
-	} while (upper != tmp);						\
+		upper = I915_READ(upper_reg);				\
+	} while (upper != old_upper && loop++ < 2);			\
 	(u64)upper << 32 | lower; })
 
 #define POSTING_READ(reg)	(void)I915_READ_NOTRACE(reg)

drivers/gpu/drm/i915/i915_gem_execbuffer.c

@@ -1032,6 +1032,7 @@ i915_gem_execbuffer_move_to_active(struct list_head *vmas,
 		u32 old_read = obj->base.read_domains;
 		u32 old_write = obj->base.write_domain;
 
+		obj->dirty = 1; /* be paranoid  */
 		obj->base.write_domain = obj->base.pending_write_domain;
 		if (obj->base.write_domain == 0)
 			obj->base.pending_read_domains |= obj->base.read_domains;
@@ -1039,7 +1040,6 @@ i915_gem_execbuffer_move_to_active(struct list_head *vmas,
 
 		i915_vma_move_to_active(vma, req);
 		if (obj->base.write_domain) {
-			obj->dirty = 1;
 			i915_gem_request_assign(&obj->last_write_req, req);
 
 			intel_fb_obj_invalidate(obj, ORIGIN_CS);

drivers/gpu/drm/i915/i915_irq.c

@@ -1558,7 +1558,7 @@ static void i9xx_hpd_irq_handler(struct drm_device *dev)
 		u32 hotplug_trigger = hotplug_status & HOTPLUG_INT_STATUS_I915;
 
 		intel_get_hpd_pins(&pin_mask, &long_mask, hotplug_trigger,
-				   hotplug_trigger, hpd_status_g4x,
+				   hotplug_trigger, hpd_status_i915,
 				   i9xx_port_hotplug_long_detect);
 		intel_hpd_irq_handler(dev, pin_mask, long_mask);
 	}

drivers/gpu/drm/i915/intel_csr.c

@@ -350,7 +350,7 @@ static void finish_csr_load(const struct firmware *fw, void *context)
 	}
 	csr->mmio_count = dmc_header->mmio_count;
 	for (i = 0; i < dmc_header->mmio_count; i++) {
-		if (dmc_header->mmioaddr[i] < CSR_MMIO_START_RANGE &&
+		if (dmc_header->mmioaddr[i] < CSR_MMIO_START_RANGE ||
 			dmc_header->mmioaddr[i] > CSR_MMIO_END_RANGE) {
 			DRM_ERROR(" Firmware has wrong mmio address 0x%x\n",
 						dmc_header->mmioaddr[i]);

drivers/gpu/drm/i915/intel_display.c

@@ -6305,7 +6305,7 @@ static void intel_connector_check_state(struct intel_connector *connector)
 		      connector->base.name);
 
 	if (connector->get_hw_state(connector)) {
-		struct drm_encoder *encoder = &connector->encoder->base;
+		struct intel_encoder *encoder = connector->encoder;
 		struct drm_connector_state *conn_state = connector->base.state;
 
 		I915_STATE_WARN(!crtc,
@@ -6317,13 +6317,13 @@ static void intel_connector_check_state(struct intel_connector *connector)
 		I915_STATE_WARN(!crtc->state->active,
 		      "connector is active, but attached crtc isn't\n");
 
-		if (!encoder)
+		if (!encoder || encoder->type == INTEL_OUTPUT_DP_MST)
 			return;
 
-		I915_STATE_WARN(conn_state->best_encoder != encoder,
+		I915_STATE_WARN(conn_state->best_encoder != &encoder->base,
 			"atomic encoder doesn't match attached encoder\n");
 
-		I915_STATE_WARN(conn_state->crtc != encoder->crtc,
+		I915_STATE_WARN(conn_state->crtc != encoder->base.crtc,
 			"attached encoder crtc differs from connector crtc\n");
 	} else {
 		I915_STATE_WARN(crtc && crtc->state->active,

drivers/gpu/drm/i915/intel_dp_mst.c

@@ -173,6 +173,11 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder)
 		return;
 	}
 
+	/* MST encoders are bound to a crtc, not to a connector,
+	 * force the mapping here for get_hw_state.
+	 */
+	found->encoder = encoder;
+
 	DRM_DEBUG_KMS("%d\n", intel_dp->active_mst_links);
 	intel_mst->port = found->port;
 
@@ -400,7 +405,7 @@ static const struct drm_encoder_funcs intel_dp_mst_enc_funcs = {
 
 static bool intel_dp_mst_get_hw_state(struct intel_connector *connector)
 {
-	if (connector->encoder) {
+	if (connector->encoder && connector->base.state->crtc) {
 		enum pipe pipe;
 		if (!connector->encoder->get_hw_state(connector->encoder, &pipe))
 			return false;

drivers/gpu/drm/i915/intel_dsi.c

@@ -1048,11 +1048,7 @@ void intel_dsi_init(struct drm_device *dev)
 	intel_connector->unregister = intel_connector_unregister;
 
 	/* Pipe A maps to MIPI DSI port A, pipe B maps to MIPI DSI port C */
-	if (dev_priv->vbt.dsi.config->dual_link) {
-		/* XXX: does dual link work on either pipe? */
-		intel_encoder->crtc_mask = (1 << PIPE_A);
-		intel_dsi->ports = ((1 << PORT_A) | (1 << PORT_C));
-	} else if (dev_priv->vbt.dsi.port == DVO_PORT_MIPIA) {
+	if (dev_priv->vbt.dsi.port == DVO_PORT_MIPIA) {
 		intel_encoder->crtc_mask = (1 << PIPE_A);
 		intel_dsi->ports = (1 << PORT_A);
 	} else if (dev_priv->vbt.dsi.port == DVO_PORT_MIPIC) {
@@ -1060,6 +1056,9 @@ void intel_dsi_init(struct drm_device *dev)
 		intel_dsi->ports = (1 << PORT_C);
 	}
 
+	if (dev_priv->vbt.dsi.config->dual_link)
+		intel_dsi->ports = ((1 << PORT_A) | (1 << PORT_C));
+
 	/* Create a DSI host (and a device) for each port. */
 	for_each_dsi_port(port, intel_dsi->ports) {
 		struct intel_dsi_host *host;

drivers/gpu/drm/i915/intel_pm.c

@@ -955,8 +955,6 @@ enum vlv_wm_level {
 	VLV_WM_LEVEL_PM2,
 	VLV_WM_LEVEL_PM5,
 	VLV_WM_LEVEL_DDR_DVFS,
-	CHV_WM_NUM_LEVELS,
-	VLV_WM_NUM_LEVELS = 1,
 };
 
 /* latency must be in 0.1us units. */
@@ -982,9 +980,13 @@ static void vlv_setup_wm_latency(struct drm_device *dev)
 	/* all latencies in usec */
 	dev_priv->wm.pri_latency[VLV_WM_LEVEL_PM2] = 3;
 
+	dev_priv->wm.max_level = VLV_WM_LEVEL_PM2;
+
 	if (IS_CHERRYVIEW(dev_priv)) {
 		dev_priv->wm.pri_latency[VLV_WM_LEVEL_PM5] = 12;
 		dev_priv->wm.pri_latency[VLV_WM_LEVEL_DDR_DVFS] = 33;
+
+		dev_priv->wm.max_level = VLV_WM_LEVEL_DDR_DVFS;
 	}
 }
 
@@ -1137,10 +1139,7 @@ static void vlv_compute_wm(struct intel_crtc *crtc)
 	memset(wm_state, 0, sizeof(*wm_state));
 
 	wm_state->cxsr = crtc->pipe != PIPE_C && crtc->wm.cxsr_allowed;
-	if (IS_CHERRYVIEW(dev))
-		wm_state->num_levels = CHV_WM_NUM_LEVELS;
-	else
-		wm_state->num_levels = VLV_WM_NUM_LEVELS;
+	wm_state->num_levels = to_i915(dev)->wm.max_level + 1;
 
 	wm_state->num_active_planes = 0;
 
@@ -1220,7 +1219,7 @@ static void vlv_compute_wm(struct intel_crtc *crtc)
 	}
 
 	/* clear any (partially) filled invalid levels */
-	for (level = wm_state->num_levels; level < CHV_WM_NUM_LEVELS; level++) {
+	for (level = wm_state->num_levels; level < to_i915(dev)->wm.max_level + 1; level++) {
 		memset(&wm_state->wm[level], 0, sizeof(wm_state->wm[level]));
 		memset(&wm_state->sr[level], 0, sizeof(wm_state->sr[level]));
 	}
@@ -1324,10 +1323,7 @@ static void vlv_merge_wm(struct drm_device *dev,
 	struct intel_crtc *crtc;
 	int num_active_crtcs = 0;
 
-	if (IS_CHERRYVIEW(dev))
-		wm->level = VLV_WM_LEVEL_DDR_DVFS;
-	else
-		wm->level = VLV_WM_LEVEL_PM2;
+	wm->level = to_i915(dev)->wm.max_level;
 	wm->cxsr = true;
 
 	for_each_intel_crtc(dev, crtc) {
@@ -4083,9 +4079,29 @@ void vlv_wm_get_hw_state(struct drm_device *dev)
 		if (val & DSP_MAXFIFO_PM5_ENABLE)
 			wm->level = VLV_WM_LEVEL_PM5;
 
+		/*
+		 * If DDR DVFS is disabled in the BIOS, Punit
+		 * will never ack the request. So if that happens
+		 * assume we don't have to enable/disable DDR DVFS
+		 * dynamically. To test that just set the REQ_ACK
+		 * bit to poke the Punit, but don't change the
+		 * HIGH/LOW bits so that we don't actually change
+		 * the current state.
+		 */
 		val = vlv_punit_read(dev_priv, PUNIT_REG_DDR_SETUP2);
-		if ((val & FORCE_DDR_HIGH_FREQ) == 0)
-			wm->level = VLV_WM_LEVEL_DDR_DVFS;
+		val |= FORCE_DDR_FREQ_REQ_ACK;
+		vlv_punit_write(dev_priv, PUNIT_REG_DDR_SETUP2, val);
+
+		if (wait_for((vlv_punit_read(dev_priv, PUNIT_REG_DDR_SETUP2) &
+			      FORCE_DDR_FREQ_REQ_ACK) == 0, 3)) {
+			DRM_DEBUG_KMS("Punit not acking DDR DVFS request, "
+				      "assuming DDR DVFS is disabled\n");
+			dev_priv->wm.max_level = VLV_WM_LEVEL_PM5;
+		} else {
+			val = vlv_punit_read(dev_priv, PUNIT_REG_DDR_SETUP2);
+			if ((val & FORCE_DDR_HIGH_FREQ) == 0)
+				wm->level = VLV_WM_LEVEL_DDR_DVFS;
+		}
 
 		mutex_unlock(&dev_priv->rps.hw_lock);
 	}

drivers/gpu/drm/nouveau/nvkm/engine/device/pci.c

@@ -689,6 +689,7 @@ nvkm_device_pci_10de_11e3[] = {
 
 static const struct nvkm_device_pci_vendor
 nvkm_device_pci_10de_11fc[] = {
+	{ 0x1179, 0x0001, NULL, { .War00C800_0 = true } }, /* Toshiba Tecra W50 */
 	{ 0x17aa, 0x2211, NULL, { .War00C800_0 = true } }, /* Lenovo W541 */
 	{ 0x17aa, 0x221e, NULL, { .War00C800_0 = true } }, /* Lenovo W541 */
 	{}

drivers/gpu/drm/nouveau/nvkm/engine/gr/nv04.c

@@ -1048,11 +1048,11 @@ nv04_gr_object_bind(struct nvkm_object *object, struct nvkm_gpuobj *parent,
 	if (ret == 0) {
 		nvkm_kmap(*pgpuobj);
 		nvkm_wo32(*pgpuobj, 0x00, object->oclass);
-		nvkm_wo32(*pgpuobj, 0x04, 0x00000000);
-		nvkm_wo32(*pgpuobj, 0x08, 0x00000000);
 #ifdef __BIG_ENDIAN
-		nvkm_mo32(*pgpuobj, 0x08, 0x00080000, 0x00080000);
+		nvkm_mo32(*pgpuobj, 0x00, 0x00080000, 0x00080000);
 #endif
+		nvkm_wo32(*pgpuobj, 0x04, 0x00000000);
+		nvkm_wo32(*pgpuobj, 0x08, 0x00000000);
 		nvkm_wo32(*pgpuobj, 0x0c, 0x00000000);
 		nvkm_done(*pgpuobj);
 	}

drivers/gpu/drm/nouveau/nvkm/subdev/clk/gt215.c

@@ -326,7 +326,7 @@ gt215_clk_pre(struct nvkm_clk *clk, unsigned long *flags)
 		return -EIO;
 
 	if (nvkm_msec(device, 2000,
-		u32 tmp = nvkm_rd32(device, 0x002504) & 0x0000003f;
+		u32 tmp = nvkm_rd32(device, 0x00251c) & 0x0000003f;
 		if (tmp == 0x0000003f)
 			break;
 	) < 0)

drivers/gpu/drm/qxl/qxl_display.c

@@ -160,9 +160,35 @@ static int qxl_add_monitors_config_modes(struct drm_connector *connector,
 	*pwidth = head->width;
 	*pheight = head->height;
 	drm_mode_probed_add(connector, mode);
+	/* remember the last custom size for mode validation */
+	qdev->monitors_config_width = mode->hdisplay;
+	qdev->monitors_config_height = mode->vdisplay;
 	return 1;
 }
 
+static struct mode_size {
+	int w;
+	int h;
+} common_modes[] = {
+	{ 640,  480},
+	{ 720,  480},
+	{ 800,  600},
+	{ 848,  480},
+	{1024,  768},
+	{1152,  768},
+	{1280,  720},
+	{1280,  800},
+	{1280,  854},
+	{1280,  960},
+	{1280, 1024},
+	{1440,  900},
+	{1400, 1050},
+	{1680, 1050},
+	{1600, 1200},
+	{1920, 1080},
+	{1920, 1200}
+};
+
 static int qxl_add_common_modes(struct drm_connector *connector,
                                 unsigned pwidth,
                                 unsigned pheight)
@@ -170,29 +196,6 @@ static int qxl_add_common_modes(struct drm_connector *connector,
 	struct drm_device *dev = connector->dev;
 	struct drm_display_mode *mode = NULL;
 	int i;
-	struct mode_size {
-		int w;
-		int h;
-	} common_modes[] = {
-		{ 640,  480},
-		{ 720,  480},
-		{ 800,  600},
-		{ 848,  480},
-		{1024,  768},
-		{1152,  768},
-		{1280,  720},
-		{1280,  800},
-		{1280,  854},
-		{1280,  960},
-		{1280, 1024},
-		{1440,  900},
-		{1400, 1050},
-		{1680, 1050},
-		{1600, 1200},
-		{1920, 1080},
-		{1920, 1200}
-	};
-
 	for (i = 0; i < ARRAY_SIZE(common_modes); i++) {
 		mode = drm_cvt_mode(dev, common_modes[i].w, common_modes[i].h,
 				    60, false, false, false);
@@ -823,11 +826,22 @@ static int qxl_conn_get_modes(struct drm_connector *connector)
 static int qxl_conn_mode_valid(struct drm_connector *connector,
 			       struct drm_display_mode *mode)
 {
+	struct drm_device *ddev = connector->dev;
+	struct qxl_device *qdev = ddev->dev_private;
+	int i;
+
 	/* TODO: is this called for user defined modes? (xrandr --add-mode)
 	 * TODO: check that the mode fits in the framebuffer */
-	DRM_DEBUG("%s: %dx%d status=%d\n", mode->name, mode->hdisplay,
-		  mode->vdisplay, mode->status);
-	return MODE_OK;
+
+	if(qdev->monitors_config_width == mode->hdisplay &&
+	   qdev->monitors_config_height == mode->vdisplay)
+		return MODE_OK;
+
+	for (i = 0; i < ARRAY_SIZE(common_modes); i++) {
+		if (common_modes[i].w == mode->hdisplay && common_modes[i].h == mode->vdisplay)
+			return MODE_OK;
+	}
+	return MODE_BAD;
 }
 
 static struct drm_encoder *qxl_best_encoder(struct drm_connector *connector)

drivers/gpu/drm/qxl/qxl_drv.h

@@ -325,6 +325,8 @@ struct qxl_device {
 	struct work_struct fb_work;
 
 	struct drm_property *hotplug_mode_update_property;
+	int monitors_config_width;
+	int monitors_config_height;
 };
 
 /* forward declaration for QXL_INFO_IO */

include/uapi/drm/i915_drm.h

@@ -358,7 +358,7 @@ typedef struct drm_i915_irq_wait {
 #define I915_PARAM_HAS_RESOURCE_STREAMER 36
 
 typedef struct drm_i915_getparam {
-	s32 param;
+	__s32 param;
 	/*
 	 * WARNING: Using pointers instead of fixed-size u64 means we need to write
 	 * compat32 code. Don't repeat this mistake.