Merge tag 'qcom-arm64-for-6.5-2' of...

Merge tag 'qcom-arm64-for-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt

More Qualcomm ARM64 DTS changes for v6.5

This introduces support for the Qualcomm SDX75 platform, with the IDP
reference board. On IPQ5332 the RDP474 board is added and on IPQ9574 the
RDP454 is introduced.
On SC8280XP, and hence Lenovo ThinkPad X13s, GPU support is added.

For QDU1000, SDM845, SM670, SC8180X, SM6350 and SM8550 the RSC is added
to the CPU cluster power-domain to flush sleep & wake votes as the
cluster goes down.

On IPQ5332 additional reserved-memory regions to improve post mortem
debugging. UART1 is added. The MI01.2 board is renamed RDP441 and the
RDP474 is added.

On IPQ8074 critical thermal trip points are defined.

As with IPQ5332 additional reserved-memory regions are used to improve
post mortem debugging. Thermal sensors (tsens) are added and zones
defined. The crypto engine is added, and support for the RDP454 board is
added.

Across MSM8916 and MSM8939 pinctrl state definitions are cleaned up and
the purpose of msm8939-pm8916 is documented. MSM8939 has regulator
definitions cleaned up, following to the previous effort on MSM8916.

CPU Bus Fabric scaling support is added to MSM8996 Pro.

On QCM2290 CPU idle states are added.

For QDU1000 SDHCI is introduced and enabled on the IDP to gain eMMC
support. IMEM and PIL information regions are defined for improved post
mortem debugging.

The Qualcomm Robotics RB2 kit gets its on-board buttons described.

A few fixes are introduced for the newly merged SC8180X, in particluar
the DisplayPort blocks are moved to the MMCX power domain to avoid power
being reduced prematurely during boot.

The SC8280XP GPU is added and enabled for the Lenovo Thinkpad X13s,
and resets for the soundwire controllers are added. The OUI is
specified for ethernet phys on SA8540P Ride platform, to avoid reset
issues.

Charger description is added to the PMI8998 PMIC and enabled across
OnePlus 6/6T, SHIFT SHIFT6mq and Xiaomi Pocophone F1.

On SM6350 CPU idle states and UART1 are added. And SM6375 gains GPU
clock controller and IOMMU definitions.

The Fairphone FP4 gains Bluetooth support.

SM8150 is transitioned to use 2 interconnect-cells, and the USB
interconnect path is described to ensure buses are adequately voted for.

The same changes are done for SM8250, and the resolution of the
static framebuffer on Sony Xperia 1 II and 5 II are corrected.

The USB bus paths are also added to SM8350, SM8450 and SM8550.

On SM8550 DisplayPort nodes are added, as is the PWM controller for
driving the notification LED and the RTC is enabled. For the MTP and QRD
boards, the soundcard and audio codecs are defined.

A Tegra change, related to LP855X binding changes, was accidentally
picked up and dropped again later.

A number of DeviceTree fixes identified through validation was
introduced as well. Additionally a few nodes got their default status
changed to avoid unnecessarily having to enable them (e.g. the mdp/dpu
node).

* tag 'qcom-arm64-for-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (94 commits)
  Revert "arm64: dts: adapt to LP855X bindings changes"
  arm64: dts: qcom: sc8280xp: Enable GPU related nodes
  arm64: dts: qcom: sc8280xp: Add GPU related nodes
  arm64: dts: qcom: msm8939-pm8916: Mark always-on regulators
  arm64: dts: qcom: msm8939: Define regulator constraints next to usage
  arm64: dts: qcom: msm8939-pm8916: Clarify purpose
  arm64: dts: qcom: msm8939: Fix regulator constraints
  arm64: dts: qcom: msm8939-sony-tulip: Allow disabling pm8916_l6
  arm64: dts: qcom: msm8939-sony-tulip: Fix l10-l12 regulator voltages
  arm64: dts: qcom: msm8939: Disable lpass_codec by default
  arm64: dts: qcom: msm8939-pm8916: Add missing pm8916_codec supplies
  arm64: dts: qcom: qrb4210-rb2: Enable on-board buttons
  arm64: dts: qcom: msm8916: Drop msm8916-pins.dtsi
  arm64: dts: qcom: msm8916/39: Rename wcnss pinctrl
  arm64: dts: qcom: msm8916/39: Cleanup audio pinctrl
  arm64: dts: qcom: apq8016-sbc: Drop unneeded MCLK pinctrl
  arm64: dts: qcom: msm8916/39: Consolidate SDC pinctrl
  arm64: dts: qcom: msm8916/39: Fix SD card detect pinctrl
  arm64: dts: qcom: msm8996: rename labels for HDMI nodes
  arm64: dts: qcom: sm8250: rename labels for DSI nodes
  ...

Link: https://lore.kernel.org/r/20230615162043.1461624-1-andersson@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/qcom.yaml

@@ -70,6 +70,7 @@ description: |
         sdm845
         sdx55
         sdx65
+        sdx75
         sm4250
         sm6115
         sm6115p
@@ -90,9 +91,11 @@ description: |
         ap-al02-c6
         ap-al02-c7
         ap-al02-c8
+        ap-al02-c9
         ap-mi01.2
         ap-mi01.3
         ap-mi01.6
+        ap-mi01.9
         cdp
         cp01-c1
         dragonboard
@@ -196,6 +199,7 @@ properties:
       - items:
           - enum:
               - qcom,msm8960-cdp
+              - samsung,expressatt
           - const: qcom,msm8960
 
       - items:
@@ -340,6 +344,7 @@ properties:
               - qcom,ipq5332-ap-mi01.2
               - qcom,ipq5332-ap-mi01.3
               - qcom,ipq5332-ap-mi01.6
+              - qcom,ipq5332-ap-mi01.9
           - const: qcom,ipq5332
 
       - items:
@@ -361,6 +366,7 @@ properties:
               - qcom,ipq9574-ap-al02-c6
               - qcom,ipq9574-ap-al02-c7
               - qcom,ipq9574-ap-al02-c8
+              - qcom,ipq9574-ap-al02-c9
           - const: qcom,ipq9574
 
       - description: Sierra Wireless MangOH Green with WP8548 Module
@@ -828,6 +834,11 @@ properties:
               - qcom,sdx65-mtp
           - const: qcom,sdx65
 
+      - items:
+          - enum:
+              - qcom,sdx75-idp
+          - const: qcom,sdx75
+
       - items:
           - enum:
               - qcom,ipq6018-cp01
@@ -1056,6 +1067,7 @@ allOf:
               - qcom,sdm845
               - qcom,sdx55
               - qcom,sdx65
+              - qcom,sdx75
               - qcom,sm4250
               - qcom,sm6115
               - qcom,sm6125

Documentation/devicetree/bindings/clock/qcom,sc8280xp-lpasscc.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/qcom,sc8280xp-lpasscc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm LPASS Core & Audio Clock Controller on SC8280XP
+
+maintainers:
+  - Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
+
+description: |
+  Qualcomm LPASS core and audio clock control module provides the clocks,
+  and reset on SC8280XP.
+
+  See also::
+    include/dt-bindings/clock/qcom,lpasscc-sc8280xp.h
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc8280xp-lpassaudiocc
+      - qcom,sc8280xp-lpasscc
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+  - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,sc8280xp-lpasscc.h>
+    lpass_audiocc: clock-controller@32a9000 {
+        compatible = "qcom,sc8280xp-lpassaudiocc";
+        reg = <0x032a9000 0x1000>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };
+
+  - |
+    #include <dt-bindings/clock/qcom,sc8280xp-lpasscc.h>
+    lpasscc: clock-controller@33e0000 {
+        compatible = "qcom,sc8280xp-lpasscc";
+        reg = <0x033e0000 0x12000>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };
+...

Documentation/devicetree/bindings/clock/qcom,sdx75-gcc.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/qcom,sdx75-gcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Global Clock & Reset Controller on SDX75
+
+maintainers:
+  - Imran Shaik <quic_imrashai@quicinc.com>
+  - Taniya Das <quic_tdas@quicinc.com>
+
+description: |
+  Qualcomm global clock control module provides the clocks, resets and power
+  domains on SDX75
+
+  See also:: include/dt-bindings/clock/qcom,sdx75-gcc.h
+
+properties:
+  compatible:
+    const: qcom,sdx75-gcc
+
+  clocks:
+    items:
+      - description: Board XO source
+      - description: Sleep clock source
+      - description: EMAC0 sgmiiphy mac rclk source
+      - description: EMAC0 sgmiiphy mac tclk source
+      - description: EMAC0 sgmiiphy rclk source
+      - description: EMAC0 sgmiiphy tclk source
+      - description: EMAC1 sgmiiphy mac rclk source
+      - description: EMAC1 sgmiiphy mac tclk source
+      - description: EMAC1 sgmiiphy rclk source
+      - description: EMAC1 sgmiiphy tclk source
+      - description: PCIE20 phy aux clock source
+      - description: PCIE_1 Pipe clock source
+      - description: PCIE_2 Pipe clock source
+      - description: PCIE Pipe clock source
+      - description: USB3 phy wrapper pipe clock source
+
+required:
+  - compatible
+  - clocks
+
+allOf:
+  - $ref: qcom,gcc.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,rpmh.h>
+    clock-controller@80000 {
+      compatible = "qcom,sdx75-gcc";
+      reg = <0x80000 0x1f7400>;
+      clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>, <&emac0_sgmiiphy_mac_rclk>,
+               <&emac0_sgmiiphy_mac_tclk>, <&emac0_sgmiiphy_rclk>, <&emac0_sgmiiphy_tclk>,
+               <&emac1_sgmiiphy_mac_rclk>, <&emac1_sgmiiphy_mac_tclk>, <&emac1_sgmiiphy_rclk>,
+               <&emac1_sgmiiphy_tclk>, <&pcie20_phy_aux_clk>, <&pcie_1_pipe_clk>,
+               <&pcie_2_pipe_clk>, <&pcie_pipe_clk>, <&usb3_phy_wrapper_gcc_usb30_pipe_clk>;
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+      #power-domain-cells = <1>;
+    };
+...

arch/arm64/boot/dts/qcom/Makefile

@@ -4,9 +4,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= apq8039-t2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8094-sony-xperia-kitakami-karin_windy.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-ifc6640.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-mi01.2.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-rdp441.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-rdp442.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-rdp468.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-rdp474.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c1.dtb
@@ -15,6 +16,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= ipq9574-rdp418.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq9574-rdp433.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq9574-rdp449.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq9574-rdp453.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= ipq9574-rdp454.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-acer-a1-724.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-alcatel-idol347.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-asus-z00l.dtb
@@ -182,6 +184,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-polaris.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-shift-axolotl.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-samsung-w737.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdx75-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115p-lenovo-j606f.dtb

arch/arm64/boot/dts/qcom/apq8016-sbc.dts

@@ -370,18 +370,14 @@ pm8916_l17: l17 {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
@@ -389,8 +385,8 @@ &sdhc_2 {
 &sound {
 	status = "okay";
 
-	pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
-	pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
+	pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
+	pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
 	pinctrl-names = "default", "sleep";
 	model = "DB410c";
 	audio-routing =
@@ -642,6 +638,13 @@ &tlmm {
 		"USR_LED_2_CTRL", /* GPIO 120 */
 		"SB_HS_ID";
 
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	tlmm_leds: tlmm-leds-state {
 		pins = "gpio21", "gpio120";
 		function = "gpio";

arch/arm64/boot/dts/qcom/apq8039-t2.dts

@@ -135,6 +135,10 @@ &lpass {
 	status = "okay";
 };
 
+&lpass_codec {
+	status = "okay";
+};
+
 &mdss {
 	status = "okay";
 };
@@ -154,108 +158,7 @@ &pm8916_gpios {
 		"PM_GPIO4";
 };
 
-&smd_rpm_regulators {
-	vdd_l1_l2_l3-supply = <&pm8916_s3>;
-	vdd_l4_l5_l6-supply = <&pm8916_s4>;
-	vdd_l7-supply = <&pm8916_s4>;
-
-	pm8916_s3: s3 {
-		regulator-min-microvolt = <1200000>;
-		regulator-max-microvolt = <1300000>;
-	};
-
-	pm8916_s4: s4 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <2100000>;
-	};
-
-	/* l1 is fixed to 1225000, but not connected in schematic */
-
-	pm8916_l2: l2 {
-		regulator-min-microvolt = <1200000>;
-		regulator-max-microvolt = <1200000>;
-	};
-
-	pm8916_l4: l4 {
-		regulator-min-microvolt = <2050000>;
-		regulator-max-microvolt = <2050000>;
-	};
-
-	pm8916_l5: l5 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	pm8916_l6: l6 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	pm8916_l7: l7 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	pm8916_l8: l8 {
-		regulator-min-microvolt = <2850000>;
-		regulator-max-microvolt = <2900000>;
-	};
-
-	pm8916_l9: l9 {
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l10: l10 {
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l11: l11 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <2950000>;
-	};
-
-	pm8916_l12: l12 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <2950000>;
-	};
-
-	pm8916_l13: l13 {
-		regulator-min-microvolt = <3075000>;
-		regulator-max-microvolt = <3075000>;
-	};
-
-	pm8916_l14: l14 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l15: l15 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l16: l16 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l17: l17 {
-		regulator-min-microvolt = <2850000>;
-		regulator-max-microvolt = <2850000>;
-	};
-
-	pm8916_l18: l18 {
-		regulator-min-microvolt = <2700000>;
-		regulator-max-microvolt = <2700000>;
-	};
-};
-
 &sdhc_1 {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_default_state>;
-	pinctrl-1 = <&sdc1_sleep_state>;
 	status = "okay";
 };
 
@@ -263,8 +166,8 @@ &sound {
 	model = "apq8039-square-sndcard";
 	audio-routing = "AMIC2", "MIC BIAS Internal2";
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cdc_pdm_lines_default>;
-	pinctrl-1 = <&cdc_pdm_lines_sleep>;
+	pinctrl-0 = <&cdc_pdm_default>;
+	pinctrl-1 = <&cdc_pdm_sleep>;
 
 	internal-codec-playback-dai-link {
 		link-name = "WCD";

arch/arm64/boot/dts/qcom/apq8096-db820c.dts

@@ -208,25 +208,6 @@ &gpu {
 	status = "okay";
 };
 
-&hdmi {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
-	pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
-
-	core-vdda-supply = <&vreg_l12a_1p8>;
-	core-vcc-supply = <&vreg_s4a_1p8>;
-};
-
-&hdmi_phy {
-	status = "okay";
-
-	vddio-supply = <&vreg_l12a_1p8>;
-	vcca-supply = <&vreg_l28a_0p925>;
-	#phy-cells = <0>;
-};
-
 &hsusb_phy1 {
 	status = "okay";
 
@@ -251,6 +232,25 @@ &mdss {
 	status = "okay";
 };
 
+&mdss_hdmi {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mdss_hdmi_hpd_active &mdss_hdmi_ddc_active>;
+	pinctrl-1 = <&mdss_hdmi_hpd_suspend &mdss_hdmi_ddc_suspend>;
+
+	core-vdda-supply = <&vreg_l12a_1p8>;
+	core-vcc-supply = <&vreg_s4a_1p8>;
+};
+
+&mdss_hdmi_phy {
+	status = "okay";
+
+	vddio-supply = <&vreg_l12a_1p8>;
+	vcca-supply = <&vreg_l28a_0p925>;
+	#phy-cells = <0>;
+};
+
 &mmcc {
 	vdd-gfx-supply = <&vdd_gfx>;
 };
@@ -433,28 +433,28 @@ sdc2_cd_off: sdc2-cd-off-state {
 		drive-strength = <2>;
 	};
 
-	hdmi_hpd_active: hdmi-hpd-active-state {
+	mdss_hdmi_hpd_active: mdss_hdmi-hpd-active-state {
 		pins = "gpio34";
 		function = "hdmi_hot";
 		bias-pull-down;
 		drive-strength = <16>;
 	};
 
-	hdmi_hpd_suspend: hdmi-hpd-suspend-state {
+	mdss_hdmi_hpd_suspend: mdss_hdmi-hpd-suspend-state {
 		pins = "gpio34";
 		function = "hdmi_hot";
 		bias-pull-down;
 		drive-strength = <2>;
 	};
 
-	hdmi_ddc_active: hdmi-ddc-active-state {
+	mdss_hdmi_ddc_active: mdss_hdmi-ddc-active-state {
 		pins = "gpio32", "gpio33";
 		function = "hdmi_ddc";
 		drive-strength = <2>;
 		bias-pull-up;
 	};
 
-	hdmi_ddc_suspend: hdmi-ddc-suspend-state {
+	mdss_hdmi_ddc_suspend: mdss_hdmi-ddc-suspend-state {
 		pins = "gpio32", "gpio33";
 		function = "hdmi_ddc";
 		drive-strength = <2>;
@@ -1043,7 +1043,7 @@ cpu {
 		};
 	};
 
-	hdmi-dai-link {
+	mdss_hdmi-dai-link {
 		link-name = "HDMI";
 		cpu {
 			sound-dai = <&q6afedai HDMI_RX>;
@@ -1054,7 +1054,7 @@ platform {
 		};
 
 		codec {
-			sound-dai = <&hdmi 0>;
+			sound-dai = <&mdss_hdmi 0>;
 		};
 	};
 

arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts

@@ -92,15 +92,15 @@ &gpu {
 	status = "okay";
 };
 
-&hdmi {
+&mdss {
 	status = "okay";
 };
 
-&hdmi_phy {
+&mdss_hdmi {
 	status = "okay";
 };
 
-&mdss {
+&mdss_hdmi_phy {
 	status = "okay";
 };
 

arch/arm64/boot/dts/qcom/ipq5332-rdp474.dts

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * IPQ5332 RDP474 board device tree source
+ *
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "ipq5332.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ5332 MI01.9";
+	compatible = "qcom,ipq5332-ap-mi01.9", "qcom,ipq5332";
+
+	aliases {
+		serial0 = &blsp1_uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&gpio_keys_default_state>;
+		pinctrl-names = "default";
+
+		button-wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&blsp1_uart0 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&blsp1_i2c1 {
+	clock-frequency  = <400000>;
+	pinctrl-0 = <&i2c_1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhc {
+	bus-width = <4>;
+	max-frequency = <192000000>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&sdc_default_state>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&xo_board {
+	clock-frequency = <24000000>;
+};
+
+/* PINCTRL */
+
+&tlmm {
+	gpio_keys_default_state: gpio-keys-default-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	i2c_1_pins: i2c-1-state {
+		pins = "gpio29", "gpio30";
+		function = "blsp1_i2c0";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	sdc_default_state: sdc-default-state {
+		clk-pins {
+			pins = "gpio13";
+			function = "sdc_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio12";
+			function = "sdc_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "sdc_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+};

arch/arm64/boot/dts/qcom/ipq5332.dtsi

@@ -114,6 +114,16 @@ reserved-memory {
 		#size-cells = <2>;
 		ranges;
 
+		bootloader@4a100000 {
+			reg = <0x0 0x4a100000 0x0 0x400000>;
+			no-map;
+		};
+
+		sbl@4a500000 {
+			reg = <0x0 0x4a500000 0x0 0x100000>;
+			no-map;
+		};
+
 		tz_mem: tz@4a600000 {
 			reg = <0x0 0x4a600000 0x0 0x200000>;
 			no-map;
@@ -121,7 +131,7 @@ tz_mem: tz@4a600000 {
 
 		smem@4a800000 {
 			compatible = "qcom,smem";
-			reg = <0x0 0x4a800000 0x0 0x00100000>;
+			reg = <0x0 0x4a800000 0x0 0x100000>;
 			no-map;
 
 			hwlocks = <&tcsr_mutex 0>;
@@ -225,6 +235,18 @@ blsp1_uart0: serial@78af000 {
 			status = "disabled";
 		};
 
+		blsp1_uart1: serial@78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b0000 0x200>;
+			interrupts = <GIC_SPI 291 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
 		blsp1_spi0: spi@78b5000 {
 			compatible = "qcom,spi-qup-v2.2.1";
 			reg = <0x078b5000 0x600>;

arch/arm64/boot/dts/qcom/ipq8074.dtsi

@@ -932,6 +932,14 @@ nss-top-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 4>;
+
+			trips {
+				nss-top-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		nss0-thermal {
@@ -939,6 +947,14 @@ nss0-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 5>;
+
+			trips {
+				nss-0-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		nss1-thermal {
@@ -946,6 +962,14 @@ nss1-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 6>;
+
+			trips {
+				nss-1-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		wcss-phya0-thermal {
@@ -953,6 +977,14 @@ wcss-phya0-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 7>;
+
+			trips {
+				wcss-phya0-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		wcss-phya1-thermal {
@@ -960,6 +992,14 @@ wcss-phya1-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 8>;
+
+			trips {
+				wcss-phya1-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		cpu0_thermal: cpu0-thermal {
@@ -967,6 +1007,14 @@ cpu0_thermal: cpu0-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 9>;
+
+			trips {
+				cpu0-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		cpu1_thermal: cpu1-thermal {
@@ -974,6 +1022,14 @@ cpu1_thermal: cpu1-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 10>;
+
+			trips {
+				cpu1-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		cpu2_thermal: cpu2-thermal {
@@ -981,6 +1037,14 @@ cpu2_thermal: cpu2-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 11>;
+
+			trips {
+				cpu2-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		cpu3_thermal: cpu3-thermal {
@@ -988,6 +1052,14 @@ cpu3_thermal: cpu3-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 12>;
+
+			trips {
+				cpu3-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		cluster_thermal: cluster-thermal {
@@ -995,6 +1067,14 @@ cluster_thermal: cluster-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 13>;
+
+			trips {
+				cluster-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		wcss-phyb0-thermal {
@@ -1002,6 +1082,14 @@ wcss-phyb0-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 14>;
+
+			trips {
+				wcss-phyb0-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 
 		wcss-phyb1-thermal {
@@ -1009,6 +1097,14 @@ wcss-phyb1-thermal {
 			polling-delay = <1000>;
 
 			thermal-sensors = <&tsens 15>;
+
+			trips {
+				wcss-phyb1-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
 		};
 	};
 };

arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ9574 RDP454 board device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq9574.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C9";
+	compatible = "qcom,ipq9574-ap-al02-c9", "qcom,ipq9574";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&blsp1_spi0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&blsp1_uart2 {
+	pinctrl-0 = <&uart2_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-mp5496-regulators";
+
+		ipq9574_s1: s1 {
+		/*
+		 * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
+		 * During regulator registration, kernel not knowing the initial voltage,
+		 * considers it as zero and brings up the regulators with minimum supported voltage.
+		 * Update the regulator-min-microvolt with SVS voltage of 725mV so that
+		 * the regulators are brought up with 725mV which is sufficient for all the
+		 * corner parts to operate at 800MHz
+		 */
+			regulator-min-microvolt = <725000>;
+			regulator-max-microvolt = <1075000>;
+		};
+	};
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&tlmm {
+	spi_0_pins: spi-0-state {
+		pins = "gpio11", "gpio12", "gpio13", "gpio14";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-disable;
+	};
+};
+
+&xo_board_clk {
+	clock-frequency = <24000000>;
+};

arch/arm64/boot/dts/qcom/ipq9574.dtsi

@@ -155,6 +155,16 @@ reserved-memory {
 		#size-cells = <2>;
 		ranges;
 
+		bootloader@4a100000 {
+			reg = <0x0 0x4a100000 0x0 0x400000>;
+			no-map;
+		};
+
+		sbl@4a500000 {
+			reg = <0x0 0x4a500000 0x0 0x100000>;
+			no-map;
+		};
+
 		tz_region: tz@4a600000 {
 			reg = <0x0 0x4a600000 0x0 0x400000>;
 			no-map;
@@ -162,7 +172,7 @@ tz_region: tz@4a600000 {
 
 		smem@4aa00000 {
 			compatible = "qcom,smem";
-			reg = <0x0 0x4aa00000 0x0 0x00100000>;
+			reg = <0x0 0x4aa00000 0x0 0x100000>;
 			hwlocks = <&tcsr_mutex 0>;
 			no-map;
 		};
@@ -205,6 +215,36 @@ qfprom: efuse@a4000 {
 			#size-cells = <1>;
 		};
 
+		cryptobam: dma-controller@704000 {
+			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
+			reg = <0x00704000 0x20000>;
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <1>;
+			qcom,controlled-remotely;
+		};
+
+		crypto: crypto@73a000 {
+			compatible = "qcom,ipq9574-qce", "qcom,ipq4019-qce", "qcom,qce";
+			reg = <0x0073a000 0x6000>;
+			clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
+				 <&gcc GCC_CRYPTO_AXI_CLK>,
+				 <&gcc GCC_CRYPTO_CLK>;
+			clock-names = "iface", "bus", "core";
+			dmas = <&cryptobam 2>, <&cryptobam 3>;
+			dma-names = "rx", "tx";
+		};
+
+		tsens: thermal-sensor@4a9000 {
+			compatible = "qcom,ipq9574-tsens", "qcom,ipq8074-tsens";
+			reg = <0x004a9000 0x1000>,
+			      <0x004a8000 0x1000>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "combined";
+			#qcom,sensors = <16>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		tlmm: pinctrl@1000000 {
 			compatible = "qcom,ipq9574-tlmm";
 			reg = <0x01000000 0x300000>;
@@ -581,6 +621,214 @@ frame@b128000 {
 		};
 	};
 
+	thermal-zones {
+		nss-top-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				nss-top-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		ubi-0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				ubi_0-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		ubi-1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				ubi_1-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		ubi-2-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				ubi_2-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		ubi-3-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				ubi_3-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpuss0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpuss1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				cpu-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				cpu-critical {
+					temperature = <120000>;
+					hysteresis = <10000>;
+					type = "critical";
+				};
+
+				cpu-passive {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 11>;
+
+			trips {
+				cpu-critical {
+					temperature = <120000>;
+					hysteresis = <10000>;
+					type = "critical";
+				};
+
+				cpu-passive {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 12>;
+
+			trips {
+				cpu-critical {
+					temperature = <120000>;
+					hysteresis = <10000>;
+					type = "critical";
+				};
+
+				cpu-passive {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 13>;
+
+			trips {
+				cpu-critical {
+					temperature = <120000>;
+					hysteresis = <10000>;
+					type = "critical";
+				};
+
+				cpu-passive {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		wcss-phyb-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 14>;
+
+			trips {
+				wcss_phyb-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		top-glue-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 15>;
+
+			trips {
+				top_glue-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,

arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts

@@ -133,17 +133,13 @@ &pm8916_vib {
 };
 
 &sdhc_1 {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
-
 	status = "okay";
 };
 
 &sdhc_2 {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
 
@@ -184,6 +180,13 @@ gpio_keys_default: gpio-keys-default-state {
 		bias-pull-up;
 	};
 
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	touchscreen_default: touchscreen-default-state {
 		reset-pins {
 			pins = "gpio12";

arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts

@@ -171,18 +171,14 @@ &pm8916_vib {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
@@ -276,6 +272,13 @@ proximity_int_default: proximity-int-default-state {
 		bias-pull-up;
 	};
 
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	ts_int_reset_default: ts-int-reset-default-state {
 		pins = "gpio13", "gpio100";
 		function = "gpio";

arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts

@@ -139,10 +139,6 @@ pm8916_l17: l17 {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
@@ -150,8 +146,8 @@ &sdhc_2 {
 	vmmc-supply = <&reg_sd_vmmc>;
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
 
@@ -205,6 +201,13 @@ sd_vmmc_en_default: sd-vmmc-en-default-state {
 		bias-disable;
 	};
 
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	touchscreen_default: touchscreen-default-state {
 		touch-pins {
 			pins = "gpio13";

arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts

@@ -128,16 +128,12 @@ &pm8916_vib {
 };
 
 &sdhc_1 {
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
-	pinctrl-names = "default", "sleep";
-
 	status = "okay";
 };
 
 &sdhc_2 {
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 	pinctrl-names = "default", "sleep";
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
@@ -184,6 +180,13 @@ gpio_leds_default: gpio-led-default-state {
 		bias-disable;
 	};
 
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	touchscreen_default: touchscreen-default-state {
 		reset-pins {
 			pins = "gpio12";

arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts

@@ -260,18 +260,14 @@ &pm8916_vib {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdhc2_cd_default>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdhc2_cd_default>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 
 	/*
 	 * The Huawei device tree sets cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>.
@@ -299,8 +295,8 @@ &sound {
 		"AMIC3", "MIC BIAS External1";
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cdc_pdm_lines_act>;
-	pinctrl-1 = <&cdc_pdm_lines_sus>;
+	pinctrl-0 = <&cdc_pdm_default>;
+	pinctrl-1 = <&cdc_pdm_sleep>;
 
 	primary-dai-link {
 		link-name = "WCD";
@@ -397,7 +393,7 @@ reg_lcd_en_default: reg-lcd-en-default-state {
 		bias-disable;
 	};
 
-	sdhc2_cd_default: sdhc2-cd-default-state {
+	sdc2_cd_default: sdc2-cd-default-state {
 		pins = "gpio56";
 		function = "gpio";
 

arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts

@@ -242,19 +242,10 @@ &pm8916_vib {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
-
 	non-removable;
 };
 

arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts

@@ -125,18 +125,14 @@ &pm8916_vib {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
@@ -190,6 +186,13 @@ mag_reset_default: mag-reset-default-state {
 		bias-disable;
 	};
 
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	usb_id_default: usb-id-default-state {
 		pins = "gpio110";
 		function = "gpio";

arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi

@@ -263,18 +263,14 @@ pm8916_l17: l17 {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
@@ -391,6 +387,13 @@ nfc_i2c_default: nfc-i2c-default-state {
 		bias-disable;
 	};
 
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	tkey_default: tkey-default-state {
 		pins = "gpio98";
 		function = "gpio";

arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi

@@ -135,16 +135,12 @@ &pm8916_usbin {
 };
 
 &sdhc_1 {
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
-	pinctrl-names = "default", "sleep";
-
 	status = "okay";
 };
 
 &sdhc_2 {
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 	pinctrl-names = "default", "sleep";
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
@@ -199,4 +195,11 @@ gpio_hall_sensor_default: gpio-hall-sensor-default-state {
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
 };

arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi

@@ -97,18 +97,14 @@ &pm8916_resin {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
@@ -162,4 +158,11 @@ muic_int_default: muic-int-default-state {
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
 };

arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts

@@ -276,19 +276,10 @@ &pm8916_vib {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
-
 	non-removable;
 
 	/*

arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi

@@ -101,10 +101,6 @@ &pm8916_usbin {
 };
 
 &sdhc_1 {
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
-	pinctrl-names = "default", "sleep";
-
 	status = "okay";
 };
 

arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts

@@ -173,19 +173,10 @@ &pm8916_vib {
 
 &sdhc_1 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
 &sdhc_2 {
 	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
-
 	non-removable;
 };
 

arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi

 // SPDX-License-Identifier: GPL-2.0-only
+/*
+ * msm8939-pm8916.dtsi describes common properties (e.g. regulator connections)
+ * that apply to most devices that make use of the MSM8939 SoC and PM8916 PMIC.
+ * Many regulators have a fixed purpose in the original reference design and
+ * were rarely re-used for different purposes. Devices that deviate from the
+ * typical reference design should not make use of this include and instead add
+ * the necessary properties in the board-specific device tree.
+ */
 
 #include "msm8939.dtsi"
 #include "pm8916.dtsi"
@@ -25,33 +33,104 @@ &mpss {
 	pll-supply = <&pm8916_l7>;
 };
 
+&pm8916_codec {
+	vdd-cdc-io-supply = <&pm8916_l5>;
+	vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>;
+	vdd-micbias-supply = <&pm8916_l13>;
+};
+
 &rpm_requests {
-	smd_rpm_regulators: regulators {
+	pm8916_rpm_regulators: regulators {
 		compatible = "qcom,rpm-pm8916-regulators";
+		vdd_l1_l2_l3-supply = <&pm8916_s3>;
+		vdd_l4_l5_l6-supply = <&pm8916_s4>;
+		vdd_l7-supply = <&pm8916_s4>;
 
 		/* pm8916_s1 is managed by rpmpd (MSM8939_VDDMDCX) */
 		/* pm8916_s2 is managed by rpmpd (MSM8939_VDDCX) */
-		pm8916_s3: s3 {};
-		pm8916_s4: s4 {};
+		pm8916_s3: s3 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-always-on; /* Needed for L2 */
+		};
+		pm8916_s4: s4 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-always-on; /* Needed for L5/L7 */
+		};
+
+		/*
+		 * Some of the regulators are unused or managed by another
+		 * processor (e.g. the modem). We should still define nodes for
+		 * them to ensure the vote from the application processor can be
+		 * dropped in case the regulators are already on during boot.
+		 *
+		 * The labels for these nodes are omitted on purpose because
+		 * boards should configure a proper voltage before using them.
+		 */
+		l1 {};
+
+		pm8916_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on; /* Needed for LPDDR RAM */
+		};
 
-		pm8916_l1: l1 {};
-		pm8916_l2: l2 {};
 		/* pm8916_l3 is managed by rpmpd (MSM8939_VDDMX) */
-		pm8916_l4: l4 {};
-		pm8916_l5: l5 {};
-		pm8916_l6: l6 {};
-		pm8916_l7: l7 {};
-		pm8916_l8: l8 {};
-		pm8916_l9: l9 {};
-		pm8916_l10: l10 {};
-		pm8916_l11: l11 {};
-		pm8916_l12: l12 {};
-		pm8916_l13: l13 {};
-		pm8916_l14: l14 {};
-		pm8916_l15: l15 {};
-		pm8916_l16: l16 {};
-		pm8916_l17: l17 {};
-		pm8916_l18: l18 {};
+
+		l4 {};
+
+		pm8916_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on; /* Needed for most digital I/O */
+		};
+
+		pm8916_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8916_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on; /* Needed for CPU PLL */
+		};
+
+		pm8916_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8916_l9: l9 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		l10 {};
+
+		pm8916_l11: l11 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+			regulator-system-load = <200000>;
+		};
+
+		pm8916_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8916_l13: l13 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		l14 {};
+		l15 {};
+		l16 {};
+		l17 {};
+		l18 {};
 	};
 };
 

arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts

@@ -43,6 +43,13 @@ &mdss {
 };
 
 &tlmm {
+	sdc2_cd_default: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
 	usb_id_default: usb-id-default-state {
 		pins = "gpio110";
 		function = "gpio";
@@ -51,115 +58,13 @@ usb_id_default: usb-id-default-state {
 	};
 };
 
-&smd_rpm_regulators {
-	vdd_l1_l2_l3-supply = <&pm8916_s3>;
-	vdd_l4_l5_l6-supply = <&pm8916_s4>;
-	vdd_l7-supply = <&pm8916_s4>;
-
-	pm8916_s3: s3 {
-		regulator-min-microvolt = <1200000>;
-		regulator-max-microvolt = <1300000>;
-	};
-
-	pm8916_s4: s4 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <2100000>;
-	};
-
-	pm8916_l2: l2 {
-		regulator-min-microvolt = <1200000>;
-		regulator-max-microvolt = <1200000>;
-	};
-
-	pm8916_l4: l4 {
-		regulator-min-microvolt = <2050000>;
-		regulator-max-microvolt = <2050000>;
-	};
-
-	pm8916_l5: l5 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	pm8916_l6: l6 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-	};
-
-	pm8916_l7: l7 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	pm8916_l8: l8 {
-		regulator-min-microvolt = <2850000>;
-		regulator-max-microvolt = <2900000>;
-	};
-
-	pm8916_l9: l9 {
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l10: l10 {
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l11: l11 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-system-load = <200000>;
-		regulator-allow-set-load;
-	};
-
-	pm8916_l12: l12 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l13: l13 {
-		regulator-min-microvolt = <3075000>;
-		regulator-max-microvolt = <3075000>;
-	};
-
-	pm8916_l14: l14 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l15: l15 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l16: l16 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pm8916_l17: l17 {
-		regulator-min-microvolt = <2850000>;
-		regulator-max-microvolt = <2850000>;
-	};
-
-	pm8916_l18: l18 {
-		regulator-min-microvolt = <2700000>;
-		regulator-max-microvolt = <2700000>;
-	};
-};
-
 &sdhc_1 {
-	pinctrl-0 = <&sdc1_default_state>;
-	pinctrl-1 = <&sdc1_sleep_state>;
-	pinctrl-names = "default", "sleep";
 	status = "okay";
 };
 
 &sdhc_2 {
-	pinctrl-0 = <&sdc2_default_state>;
-	pinctrl-1 = <&sdc2_sleep_state>;
+	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 	pinctrl-names = "default", "sleep";
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
 	status = "okay";

arch/arm64/boot/dts/qcom/msm8939.dtsi

@@ -969,23 +969,7 @@ cci0_default: cci0-default-state {
 				bias-disable;
 			};
 
-			cdc_pdm_lines_default: pdm-lines-default-state {
-				pins = "gpio63", "gpio64", "gpio65", "gpio66",
-				       "gpio67", "gpio68";
-				function = "cdc_pdm0";
-				drive-strength = <8>;
-				bias-disable;
-			};
-
-			cdc_pdm_lines_sleep: pdm-lines-suspend-state {
-				pins = "gpio63", "gpio64", "gpio65", "gpio66",
-				       "gpio67", "gpio68";
-				function = "cdc_pdm0";
-				drive-strength = <2>;
-				bias-pull-down;
-			};
-
-			cdc_dmic_lines_act: cdc-dmic-lines-on-state {
+			cdc_dmic_default: cdc-dmic-default-state {
 				clk-pins {
 					pins = "gpio0";
 					function = "dmic0_clk";
@@ -999,7 +983,7 @@ data-pins {
 				};
 			};
 
-			cdc_dmic_lines_sus: cdc-dmic-lines-off-state {
+			cdc_dmic_sleep: cdc-dmic-sleep-state {
 				clk-pins {
 					pins = "gpio0";
 					function = "dmic0_clk";
@@ -1015,72 +999,79 @@ data-pins {
 				};
 			};
 
-			ext-mclk-tlmm-lines-state {
-				ext_mclk_tlmm_lines_act: mclk-lines-on-pins {
-					pins = "gpio116";
-					function = "pri_mi2s";
-					drive-strength = <8>;
-					bias-disable;
-				};
+			cdc_pdm_default: cdc-pdm-default-state {
+				pins = "gpio63", "gpio64", "gpio65", "gpio66",
+				       "gpio67", "gpio68";
+				function = "cdc_pdm0";
+				drive-strength = <8>;
+				bias-disable;
+			};
 
-				ext_mclk_tlmm_lines_sus: mclk-lines-off-pins {
-					pins = "gpio116";
-					function = "pri_mi2s";
-					drive-strength = <2>;
-					bias-disable;
-				};
+			cdc_pdm_sleep: cdc-pdm-sleep-state {
+				pins = "gpio63", "gpio64", "gpio65", "gpio66",
+				       "gpio67", "gpio68";
+				function = "cdc_pdm0";
+				drive-strength = <2>;
+				bias-pull-down;
 			};
 
-			ext-pri-tlmm-lines-state {
-				ext_pri_tlmm_lines_act: ext-pa-on-pins {
-					pins = "gpio113", "gpio114", "gpio115", "gpio116";
-					function = "pri_mi2s";
-					drive-strength = <8>;
-					bias-disable;
-				};
+			pri_mi2s_default: mi2s-pri-default-state {
+				pins = "gpio113", "gpio114", "gpio115", "gpio116";
+				function = "pri_mi2s";
+				drive-strength = <8>;
+				bias-disable;
+			};
 
-				ext_pri_tlmm_lines_sus: ext-pa-off-pins {
-					pins = "gpio113", "gpio114", "gpio115", "gpio116";
-					function = "pri_mi2s";
-					drive-strength = <2>;
-					bias-disable;
-				};
+			pri_mi2s_sleep: mi2s-pri-sleep-state {
+				pins = "gpio113", "gpio114", "gpio115", "gpio116";
+				function = "pri_mi2s";
+				drive-strength = <2>;
+				bias-disable;
 			};
 
-			ext-pri-ws-line-state {
-				ext_pri_ws_act: ext-pa-on-pins {
-					pins = "gpio110";
-					function = "pri_mi2s_ws";
-					drive-strength = <8>;
-					bias-disable;
-				};
+			pri_mi2s_mclk_default: mi2s-pri-mclk-default-state {
+				pins = "gpio116";
+				function = "pri_mi2s";
+				drive-strength = <8>;
+				bias-disable;
+			};
 
-				ext_pri_ws_sus: ext-pa-off-pins {
-					pins = "gpio110";
-					function = "pri_mi2s_ws";
-					drive-strength = <2>;
-					bias-disable;
-				};
+			pri_mi2s_mclk_sleep: mi2s-pri-mclk-sleep-state {
+				pins = "gpio116";
+				function = "pri_mi2s";
+				drive-strength = <2>;
+				bias-disable;
 			};
 
-			/* secondary Mi2S */
-			ext-sec-tlmm-lines-state {
-				ext_sec_tlmm_lines_act: tlmm-lines-on-pins {
-					pins = "gpio112", "gpio117", "gpio118", "gpio119";
-					function = "sec_mi2s";
-					drive-strength = <8>;
-					bias-disable;
-				};
+			pri_mi2s_ws_default: mi2s-pri-ws-default-state {
+				pins = "gpio110";
+				function = "pri_mi2s_ws";
+				drive-strength = <8>;
+				bias-disable;
+			};
 
-				ext_sec_tlmm_lines_sus: tlmm-lines-off-pins {
-					pins = "gpio112", "gpio117", "gpio118", "gpio119";
-					function = "sec_mi2s";
-					drive-strength = <2>;
-					bias-disable;
-				};
+			pri_mi2s_ws_sleep: mi2s-pri-ws-sleep-state {
+				pins = "gpio110";
+				function = "pri_mi2s_ws";
+				drive-strength = <2>;
+				bias-disable;
 			};
 
-			sdc1_default_state: sdc1-default-state {
+			sec_mi2s_default: mi2s-sec-default-state {
+				pins = "gpio112", "gpio117", "gpio118", "gpio119";
+				function = "sec_mi2s";
+				drive-strength = <8>;
+				bias-disable;
+			};
+
+			sec_mi2s_sleep: mi2s-sec-sleep-state {
+				pins = "gpio112", "gpio117", "gpio118", "gpio119";
+				function = "sec_mi2s";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdc1_default: sdc1-default-state {
 				clk-pins {
 					pins = "sdc1_clk";
 					bias-disable;
@@ -1100,7 +1091,7 @@ data-pins {
 				};
 			};
 
-			sdc1_sleep_state: sdc1-sleep-state {
+			sdc1_sleep: sdc1-sleep-state {
 				clk-pins {
 					pins = "sdc1_clk";
 					bias-disable;
@@ -1120,7 +1111,7 @@ data-pins {
 				};
 			};
 
-			sdc2_default_state: sdc2-default-state {
+			sdc2_default: sdc2-default-state {
 				clk-pins {
 					pins = "sdc2_clk";
 					bias-disable;
@@ -1138,16 +1129,9 @@ data-pins {
 					bias-pull-up;
 					drive-strength = <10>;
 				};
-
-				cd-pins {
-					pins = "gpio38";
-					function = "gpio";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
 			};
 
-			sdc2_sleep_state: sdc2-sleep-state {
+			sdc2_sleep: sdc2-sleep-state {
 				clk-pins {
 					pins = "sdc2_clk";
 					bias-disable;
@@ -1165,16 +1149,9 @@ data-pins {
 					bias-pull-up;
 					drive-strength = <2>;
 				};
-
-				cd-pins {
-					pins = "gpio38";
-					function = "gpio";
-					drive-strength = <2>;
-					bias-disable;
-				};
 			};
 
-			wcnss_pin_a: wcnss-active-state {
+			wcss_wlan_default: wcss-wlan-default-state {
 				pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
 				function = "wcss_wlan";
 				drive-strength = <6>;
@@ -1631,6 +1608,7 @@ lpass_codec: audio-codec@771c000 {
 				 <&gcc GCC_CODEC_DIGCODEC_CLK>;
 			clock-names = "ahbix-clk", "mclk";
 			#sound-dai-cells = <1>;
+			status = "disabled";
 		};
 
 		sdhc_1: mmc@7824900 {
@@ -1646,6 +1624,9 @@ sdhc_1: mmc@7824900 {
 				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
 			clock-names = "iface", "core", "xo";
 			resets = <&gcc GCC_SDCC1_BCR>;
+			pinctrl-0 = <&sdc1_default>;
+			pinctrl-1 = <&sdc1_sleep>;
+			pinctrl-names = "default", "sleep";
 			mmc-ddr-1_8v;
 			bus-width = <8>;
 			non-removable;
@@ -1665,6 +1646,9 @@ sdhc_2: mmc@7864900 {
 				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
 			clock-names =  "iface", "core", "xo";
 			resets = <&gcc GCC_SDCC2_BCR>;
+			pinctrl-0 = <&sdc2_default>;
+			pinctrl-1 = <&sdc2_sleep>;
+			pinctrl-names = "default", "sleep";
 			bus-width = <4>;
 			status = "disabled";
 		};
@@ -1980,7 +1964,7 @@ wcnss: remoteproc@a204000 {
 			qcom,smem-state-names = "stop";
 
 			pinctrl-names = "default";
-			pinctrl-0 = <&wcnss_pin_a>;
+			pinctrl-0 = <&wcss_wlan_default>;
 
 			status = "disabled";
 

arch/arm64/boot/dts/qcom/msm8953.dtsi

@@ -764,10 +764,10 @@ gcc: clock-controller@1800000 {
 			#power-domain-cells = <1>;
 			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
 				 <&sleep_clk>,
-				 <&dsi0_phy 1>,
-				 <&dsi0_phy 0>,
-				 <&dsi1_phy 1>,
-				 <&dsi1_phy 0>;
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi1_phy 1>,
+				 <&mdss_dsi1_phy 0>;
 			clock-names = "xo",
 				      "sleep",
 				      "dsi0pll",
@@ -849,20 +849,20 @@ ports {
 					port@0 {
 						reg = <0>;
 						mdp5_intf1_out: endpoint {
-							remote-endpoint = <&dsi0_in>;
+							remote-endpoint = <&mdss_dsi0_in>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
 						mdp5_intf2_out: endpoint {
-							remote-endpoint = <&dsi1_in>;
+							remote-endpoint = <&mdss_dsi1_in>;
 						};
 					};
 				};
 			};
 
-			dsi0: dsi@1a94000 {
+			mdss_dsi0: dsi@1a94000 {
 				compatible = "qcom,msm8953-dsi-ctrl", "qcom,mdss-dsi-ctrl";
 				reg = <0x01a94000 0x400>;
 				reg-names = "dsi_ctrl";
@@ -872,8 +872,8 @@ dsi0: dsi@1a94000 {
 
 				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
 						  <&gcc PCLK0_CLK_SRC>;
-				assigned-clock-parents = <&dsi0_phy 0>,
-							 <&dsi0_phy 1>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>,
+							 <&mdss_dsi0_phy 1>;
 
 				clocks = <&gcc GCC_MDSS_MDP_CLK>,
 					 <&gcc GCC_MDSS_AHB_CLK>,
@@ -888,7 +888,7 @@ dsi0: dsi@1a94000 {
 					      "pixel",
 					      "core";
 
-				phys = <&dsi0_phy>;
+				phys = <&mdss_dsi0_phy>;
 
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -901,20 +901,20 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi0_in: endpoint {
+						mdss_dsi0_in: endpoint {
 							remote-endpoint = <&mdp5_intf1_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi0_out: endpoint {
+						mdss_dsi0_out: endpoint {
 						};
 					};
 				};
 			};
 
-			dsi0_phy: phy@1a94400 {
+			mdss_dsi0_phy: phy@1a94400 {
 				compatible = "qcom,dsi-phy-14nm-8953";
 				reg = <0x01a94400 0x100>,
 				      <0x01a94500 0x300>,
@@ -932,7 +932,7 @@ dsi0_phy: phy@1a94400 {
 				status = "disabled";
 			};
 
-			dsi1: dsi@1a96000 {
+			mdss_dsi1: dsi@1a96000 {
 				compatible = "qcom,msm8953-dsi-ctrl", "qcom,mdss-dsi-ctrl";
 				reg = <0x01a96000 0x400>;
 				reg-names = "dsi_ctrl";
@@ -942,8 +942,8 @@ dsi1: dsi@1a96000 {
 
 				assigned-clocks = <&gcc BYTE1_CLK_SRC>,
 						  <&gcc PCLK1_CLK_SRC>;
-				assigned-clock-parents = <&dsi1_phy 0>,
-							 <&dsi1_phy 1>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>,
+							 <&mdss_dsi1_phy 1>;
 
 				clocks = <&gcc GCC_MDSS_MDP_CLK>,
 					 <&gcc GCC_MDSS_AHB_CLK>,
@@ -958,7 +958,7 @@ dsi1: dsi@1a96000 {
 					      "pixel",
 					      "core";
 
-				phys = <&dsi1_phy>;
+				phys = <&mdss_dsi1_phy>;
 
 				status = "disabled";
 
@@ -968,20 +968,20 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi1_in: endpoint {
+						mdss_dsi1_in: endpoint {
 							remote-endpoint = <&mdp5_intf2_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi1_out: endpoint {
+						mdss_dsi1_out: endpoint {
 						};
 					};
 				};
 			};
 
-			dsi1_phy: phy@1a96400 {
+			mdss_dsi1_phy: phy@1a96400 {
 				compatible = "qcom,dsi-phy-14nm-8953";
 				reg = <0x01a96400 0x100>,
 				      <0x01a96500 0x300>,

arch/arm64/boot/dts/qcom/msm8996-mtp.dts

@@ -24,10 +24,10 @@ &blsp2_uart2 {
 	status = "okay";
 };
 
-&hdmi {
+&mdss_hdmi {
 	status = "okay";
 };
 
-&hdmi_phy {
+&mdss_hdmi_phy {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/msm8996-oneplus-common.dtsi

@@ -164,21 +164,6 @@ &camss {
 	vdda-supply = <&vreg_l2a_1p25>;
 };
 
-&dsi0 {
-	vdda-supply = <&vreg_l2a_1p25>;
-	vcca-supply = <&vreg_l22a_3p0>;
-	status = "okay";
-};
-
-&dsi0_out {
-	data-lanes = <0 1 2 3>;
-};
-
-&dsi0_phy {
-	vcca-supply = <&vreg_l28a_0p925>;
-	status = "okay";
-};
-
 &hsusb_phy1 {
 	vdd-supply = <&vreg_l28a_0p925>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
@@ -201,6 +186,21 @@ &mdss {
 	status = "okay";
 };
 
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l2a_1p25>;
+	vcca-supply = <&vreg_l22a_3p0>;
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vcca-supply = <&vreg_l28a_0p925>;
+	status = "okay";
+};
+
 &mmcc {
 	vdd-gfx-supply = <&vdd_gfx>;
 };

arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi

@@ -235,7 +235,15 @@ bluetooth: bluetooth {
 	};
 };
 
-&dsi0 {
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
 	status = "okay";
 
 	vdd-supply = <&vreg_l2a_1p25>;
@@ -246,26 +254,18 @@ &dsi0 {
 	pinctrl-1 = <&mdss_dsi_sleep &mdss_te_sleep>;
 };
 
-&dsi0_out {
+&mdss_dsi0_out {
 	status = "okay";
 
 	data-lanes = <0 1 2 3>;
 };
 
-&dsi0_phy {
+&mdss_dsi0_phy {
 	status = "okay";
 
 	vcca-supply = <&vreg_l28a_0p925>;
 };
 
-&gpu {
-	status = "okay";
-};
-
-&mdss {
-	status = "okay";
-};
-
 &mmcc {
 	vdd-gfx-supply = <&vdd_gfx>;
 };

arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts

@@ -93,7 +93,13 @@ synaptics@20 {
 
 };
 
-&dsi0 {
+&gpu {
+	zap-shader {
+		firmware-name = "qcom/msm8996/gemini/a530_zap.mbn";
+	};
+};
+
+&mdss_dsi0 {
 	status = "okay";
 
 	vdd-supply = <&vreg_l2a_1p25>;
@@ -112,22 +118,16 @@ panel: panel@0 {
 
 		port {
 			panel_in: endpoint {
-				remote-endpoint = <&dsi0_out>;
+				remote-endpoint = <&mdss_dsi0_out>;
 			};
 		};
 	};
 };
 
-&dsi0_out {
+&mdss_dsi0_out {
 	remote-endpoint = <&panel_in>;
 };
 
-&gpu {
-	zap-shader {
-		firmware-name = "qcom/msm8996/gemini/a530_zap.mbn";
-	};
-};
-
 &pmi8994_wled {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/msm8996.dtsi

@@ -889,11 +889,11 @@ mmcc: clock-controller@8c0000 {
 			clocks = <&xo_board>,
 				 <&gcc GPLL0>,
 				 <&gcc GCC_MMSS_NOC_CFG_AHB_CLK>,
-				 <&dsi0_phy 1>,
-				 <&dsi0_phy 0>,
-				 <&dsi1_phy 1>,
-				 <&dsi1_phy 0>,
-				 <&hdmi_phy>;
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi1_phy 1>,
+				 <&mdss_dsi1_phy 0>,
+				 <&mdss_hdmi_phy>;
 			clock-names = "xo",
 				      "gpll0",
 				      "gcc_mmss_noc_cfg_ahb_clk",
@@ -978,27 +978,27 @@ ports {
 					port@0 {
 						reg = <0>;
 						mdp5_intf3_out: endpoint {
-							remote-endpoint = <&hdmi_in>;
+							remote-endpoint = <&mdss_hdmi_in>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
 						mdp5_intf1_out: endpoint {
-							remote-endpoint = <&dsi0_in>;
+							remote-endpoint = <&mdss_dsi0_in>;
 						};
 					};
 
 					port@2 {
 						reg = <2>;
 						mdp5_intf2_out: endpoint {
-							remote-endpoint = <&dsi1_in>;
+							remote-endpoint = <&mdss_dsi1_in>;
 						};
 					};
 				};
 			};
 
-			dsi0: dsi@994000 {
+			mdss_dsi0: dsi@994000 {
 				compatible = "qcom,msm8996-dsi-ctrl",
 					     "qcom,mdss-dsi-ctrl";
 				reg = <0x00994000 0x400>;
@@ -1022,9 +1022,9 @@ dsi0: dsi@994000 {
 					      "pixel",
 					      "core";
 				assigned-clocks = <&mmcc BYTE0_CLK_SRC>, <&mmcc PCLK0_CLK_SRC>;
-				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
 
-				phys = <&dsi0_phy>;
+				phys = <&mdss_dsi0_phy>;
 				status = "disabled";
 
 				#address-cells = <1>;
@@ -1036,20 +1036,20 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi0_in: endpoint {
+						mdss_dsi0_in: endpoint {
 							remote-endpoint = <&mdp5_intf1_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi0_out: endpoint {
+						mdss_dsi0_out: endpoint {
 						};
 					};
 				};
 			};
 
-			dsi0_phy: phy@994400 {
+			mdss_dsi0_phy: phy@994400 {
 				compatible = "qcom,dsi-phy-14nm";
 				reg = <0x00994400 0x100>,
 				      <0x00994500 0x300>,
@@ -1066,7 +1066,7 @@ dsi0_phy: phy@994400 {
 				status = "disabled";
 			};
 
-			dsi1: dsi@996000 {
+			mdss_dsi1: dsi@996000 {
 				compatible = "qcom,msm8996-dsi-ctrl",
 					     "qcom,mdss-dsi-ctrl";
 				reg = <0x00996000 0x400>;
@@ -1090,9 +1090,9 @@ dsi1: dsi@996000 {
 					      "pixel",
 					      "core";
 				assigned-clocks = <&mmcc BYTE1_CLK_SRC>, <&mmcc PCLK1_CLK_SRC>;
-				assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
 
-				phys = <&dsi1_phy>;
+				phys = <&mdss_dsi1_phy>;
 				status = "disabled";
 
 				#address-cells = <1>;
@@ -1104,20 +1104,20 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi1_in: endpoint {
+						mdss_dsi1_in: endpoint {
 							remote-endpoint = <&mdp5_intf2_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi1_out: endpoint {
+						mdss_dsi1_out: endpoint {
 						};
 					};
 				};
 			};
 
-			dsi1_phy: phy@996400 {
+			mdss_dsi1_phy: phy@996400 {
 				compatible = "qcom,dsi-phy-14nm";
 				reg = <0x00996400 0x100>,
 				      <0x00996500 0x300>,
@@ -1134,8 +1134,8 @@ dsi1_phy: phy@996400 {
 				status = "disabled";
 			};
 
-			hdmi: hdmi-tx@9a0000 {
-				compatible = "qcom,hdmi-tx-8996";
+			mdss_hdmi: mdss_hdmi-tx@9a0000 {
+				compatible = "qcom,mdss_hdmi-tx-8996";
 				reg =	<0x009a0000 0x50c>,
 					<0x00070000 0x6158>,
 					<0x009e0000 0xfff>;
@@ -1158,7 +1158,7 @@ hdmi: hdmi-tx@9a0000 {
 					"alt_iface",
 					"extp";
 
-				phys = <&hdmi_phy>;
+				phys = <&mdss_hdmi_phy>;
 				#sound-dai-cells = <1>;
 
 				status = "disabled";
@@ -1169,16 +1169,16 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						hdmi_in: endpoint {
+						mdss_hdmi_in: endpoint {
 							remote-endpoint = <&mdp5_intf3_out>;
 						};
 					};
 				};
 			};
 
-			hdmi_phy: phy@9a0600 {
+			mdss_hdmi_phy: phy@9a0600 {
 				#phy-cells = <0>;
-				compatible = "qcom,hdmi-phy-8996";
+				compatible = "qcom,mdss_hdmi-phy-8996";
 				reg = <0x009a0600 0x1c4>,
 				      <0x009a0a00 0x124>,
 				      <0x009a0c00 0x124>,

arch/arm64/boot/dts/qcom/msm8996pro-xiaomi-natrium.dts

@@ -39,7 +39,13 @@ touchscreen@20 {
 	};
 };
 
-&dsi0 {
+&gpu {
+	zap-shader {
+		firmware-name = "qcom/msm8996/natrium/a530_zap.mbn";
+	};
+};
+
+&mdss_dsi0 {
 	status = "okay";
 
 	vdda-supply = <&vreg_l2a_1p25>;
@@ -57,22 +63,16 @@ panel: panel@0 {
 
 		port {
 			panel_in: endpoint {
-				remote-endpoint = <&dsi0_out>;
+				remote-endpoint = <&mdss_dsi0_out>;
 			};
 		};
 	};
 };
 
-&dsi0_out {
+&mdss_dsi0_out {
 	remote-endpoint = <&panel_in>;
 };
 
-&gpu {
-	zap-shader {
-		firmware-name = "qcom/msm8996/natrium/a530_zap.mbn";
-	};
-};
-
 &mss_pil {
 	firmware-name = "qcom/msm8996/natrium/mba.mbn",
 			"qcom/msm8996/natrium/modem.mbn";

arch/arm64/boot/dts/qcom/msm8996pro.dtsi

@@ -24,101 +24,121 @@ opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-384000000 {
 			opp-hz = /bits/ 64 <384000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-460800000 {
 			opp-hz = /bits/ 64 <460800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-537600000 {
 			opp-hz = /bits/ 64 <537600000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-614400000 {
 			opp-hz = /bits/ 64 <614400000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-691200000 {
 			opp-hz = /bits/ 64 <691200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <307200>;
 		};
 		opp-768000000 {
 			opp-hz = /bits/ 64 <768000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <307200>;
 		};
 		opp-844800000 {
 			opp-hz = /bits/ 64 <844800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <384000>;
 		};
 		opp-902400000 {
 			opp-hz = /bits/ 64 <902400000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <441600>;
 		};
 		opp-979200000 {
 			opp-hz = /bits/ 64 <979200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <537600>;
 		};
 		opp-1056000000 {
 			opp-hz = /bits/ 64 <1056000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <614400>;
 		};
 		opp-1132800000 {
 			opp-hz = /bits/ 64 <1132800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <691200>;
 		};
 		opp-1209600000 {
 			opp-hz = /bits/ 64 <1209600000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <768000>;
 		};
 		opp-1286400000 {
 			opp-hz = /bits/ 64 <1286400000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <844800>;
 		};
 		opp-1363200000 {
 			opp-hz = /bits/ 64 <1363200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <902400>;
 		};
 		opp-1440000000 {
 			opp-hz = /bits/ 64 <1440000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <979200>;
 		};
 		opp-1516800000 {
 			opp-hz = /bits/ 64 <1516800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1132800>;
 		};
 		opp-1593600000 {
 			opp-hz = /bits/ 64 <1593600000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1190400>;
 		};
 		opp-1996800000 {
 			opp-hz = /bits/ 64 <1996800000>;
 			opp-supported-hw = <0x20>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1516800>;
 		};
 		opp-2188800000 {
 			opp-hz = /bits/ 64 <2188800000>;
 			opp-supported-hw = <0x10>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1593600>;
 		};
 	};
 
@@ -131,136 +151,163 @@ opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-384000000 {
 			opp-hz = /bits/ 64 <384000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-460800000 {
 			opp-hz = /bits/ 64 <460800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-537600000 {
 			opp-hz = /bits/ 64 <537600000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-614400000 {
 			opp-hz = /bits/ 64 <614400000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <192000>;
 		};
 		opp-691200000 {
 			opp-hz = /bits/ 64 <691200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <307200>;
 		};
 		opp-748800000 {
 			opp-hz = /bits/ 64 <748800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <307200>;
 		};
 		opp-825600000 {
 			opp-hz = /bits/ 64 <825600000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <384000>;
 		};
 		opp-902400000 {
 			opp-hz = /bits/ 64 <902400000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <441600>;
 		};
 		opp-979200000 {
 			opp-hz = /bits/ 64 <979200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <441600>;
 		};
 		opp-1056000000 {
 			opp-hz = /bits/ 64 <1056000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <537600>;
 		};
 		opp-1132800000 {
 			opp-hz = /bits/ 64 <1132800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <614400>;
 		};
 		opp-1209600000 {
 			opp-hz = /bits/ 64 <1209600000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <691200>;
 		};
 		opp-1286400000 {
 			opp-hz = /bits/ 64 <1286400000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <768000>;
 		};
 		opp-1363200000 {
 			opp-hz = /bits/ 64 <1363200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <844800>;
 		};
 		opp-1440000000 {
 			opp-hz = /bits/ 64 <1440000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <902400>;
 		};
 		opp-1516800000 {
 			opp-hz = /bits/ 64 <1516800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <979200>;
 		};
 		opp-1593600000 {
 			opp-hz = /bits/ 64 <1593600000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1056000>;
 		};
 		opp-1670400000 {
 			opp-hz = /bits/ 64 <1670400000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1132800>;
 		};
 		opp-1747200000 {
 			opp-hz = /bits/ 64 <1747200000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1190400>;
 		};
 		opp-1824000000 {
 			opp-hz = /bits/ 64 <1824000000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1286400>;
 		};
 		opp-1900800000 {
 			opp-hz = /bits/ 64 <1900800000>;
 			opp-supported-hw = <0x70>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1363200>;
 		};
 		opp-1977600000 {
 			opp-hz = /bits/ 64 <1977600000>;
 			opp-supported-hw = <0x30>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1440000>;
 		};
 		opp-2054400000 {
 			opp-hz = /bits/ 64 <2054400000>;
 			opp-supported-hw = <0x30>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1516800>;
 		};
 		opp-2150400000 {
 			opp-hz = /bits/ 64 <2150400000>;
 			opp-supported-hw = <0x30>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1593600>;
 		};
 		opp-2246400000 {
 			opp-hz = /bits/ 64 <2246400000>;
 			opp-supported-hw = <0x10>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1593600>;
 		};
 		opp-2342400000 {
 			opp-hz = /bits/ 64 <2342400000>;
 			opp-supported-hw = <0x10>;
 			clock-latency-ns = <200000>;
+			opp-peak-kBps = <1593600>;
 		};
 	};
 };
@@ -289,3 +336,7 @@ opp-560000000 {
 	};
 	/* The rest is inherited from msm8996 */
 };
+
+&cbf {
+	compatible = "qcom,msm8996pro-cbf";
+};

arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi

@@ -279,10 +279,6 @@ vol_keys_default: vol-keys-state {
 	};
 };
 
-&pmi8998_rradc {
-	status = "okay";
-};
-
 &qusb2phy {
 	status = "okay";
 

arch/arm64/boot/dts/qcom/pm8550.dtsi

@@ -61,5 +61,15 @@ pm8550_flash: led-controller@ee00 {
 			reg = <0xee00>;
 			status = "disabled";
 		};
+
+		pm8550_pwm: pwm {
+			compatible = "qcom,pm8550-pwm", "qcom,pm8350c-pwm";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
 	};
 };

arch/arm64/boot/dts/qcom/pmi8998.dtsi

@@ -9,6 +9,26 @@ pmi8998_lsid0: pmic@2 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pmi8998_charger: charger@1000 {
+			compatible = "qcom,pmi8998-charger";
+			reg = <0x1000>;
+
+			interrupts = <0x2 0x13 0x4 IRQ_TYPE_EDGE_BOTH>,
+				     <0x2 0x12 0x2 IRQ_TYPE_EDGE_BOTH>,
+				     <0x2 0x16 0x1 IRQ_TYPE_EDGE_RISING>,
+				     <0x2 0x13 0x6 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "usb-plugin",
+					  "bat-ov",
+					  "wdog-bark",
+					  "usbin-icl-change";
+
+			io-channels = <&pmi8998_rradc 3>,
+				      <&pmi8998_rradc 4>;
+			io-channel-names = "usbin_i", "usbin_v";
+
+			status = "disabled";
+		};
+
 		pmi8998_gpios: gpio@c000 {
 			compatible = "qcom,pmi8998-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
@@ -23,8 +43,6 @@ pmi8998_rradc: adc@4500 {
 			compatible = "qcom,pmi8998-rradc";
 			reg = <0x4500>;
 			#io-channel-cells = <1>;
-
-			status = "disabled";
 		};
 	};
 

arch/arm64/boot/dts/qcom/pmk8550.dtsi

@@ -49,7 +49,6 @@ pmk8550_rtc: rtc@6100 {
 			reg = <0x6100>, <0x6200>;
 			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
-			status = "disabled";
 		};
 
 		pmk8550_sdam_2: nvram@7100 {

arch/arm64/boot/dts/qcom/qcm2290.dtsi

@@ -48,6 +48,8 @@ CPU0: cpu@0 {
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
 			L2_0: l2-cache {
 				compatible = "cache";
 				cache-level = <2>;
@@ -64,6 +66,8 @@ CPU1: cpu@1 {
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
 		};
 
 		CPU2: cpu@2 {
@@ -76,6 +80,8 @@ CPU2: cpu@2 {
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
 		};
 
 		CPU3: cpu@3 {
@@ -88,6 +94,8 @@ CPU3: cpu@3 {
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
 		};
 
 		cpu-map {
@@ -109,6 +117,30 @@ core3 {
 				};
 			};
 		};
+
+		domain-idle-states {
+			CLUSTER_SLEEP: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000043>;
+				entry-latency-us = <800>;
+				exit-latency-us = <2118>;
+				min-residency-us = <7376>;
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "power-collapse";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <290>;
+				exit-latency-us = <376>;
+				min-residency-us = <1182>;
+				local-timer-stop;
+			};
+		};
 	};
 
 	firmware {
@@ -134,6 +166,35 @@ pmu {
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
+
+		CPU_PD0: power-domain-cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP>;
+		};
+
+		CPU_PD1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP>;
+		};
+
+		CPU_PD2: power-domain-cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP>;
+		};
+
+		CPU_PD3: power-domain-cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&CPU_SLEEP>;
+		};
+
+		CLUSTER_PD: power-domain-cpu-cluster {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP>;
+		};
 	};
 
 	reserved_memory: reserved-memory {

arch/arm64/boot/dts/qcom/qdu1000-idp.dts

@@ -448,6 +448,29 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&sdhc {
+	pinctrl-0 = <&sdc_on_state>;
+	pinctrl-1 = <&sdc_off_state>;
+	pinctrl-names = "default", "sleep";
+
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+
+	non-removable;
+	no-sd;
+	no-sdio;
+
+	supports-cqe;
+
+	vmmc-supply = <&vreg_l10a_2p95>;
+	vqmmc-supply = <&vreg_l7a_1p8>;
+
+	status = "okay";
+};
+
 &uart7 {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/qdu1000.dtsi

@@ -842,6 +842,53 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		sdhc: mmc@8804000 {
+			compatible = "qcom,qdu1000-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x0 0x08804000 0x0 0x1000>,
+			      <0x0 0x08805000 0x0 0x1000>;
+			reg-names = "hc", "cqhci";
+
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC5_AHB_CLK>,
+				 <&gcc GCC_SDCC5_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface",
+				      "core",
+				      "xo";
+
+			resets = <&gcc GCC_SDCC5_BCR>;
+
+			interconnects = <&system_noc MASTER_SDCC_1 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_SDCC_2 0>;
+			interconnect-names = "sdhc-ddr", "cpu-sdhc";
+			power-domains = <&rpmhpd QDU1000_CX>;
+			operating-points-v2 = <&sdhc1_opp_table>;
+
+			iommus = <&apps_smmu 0x80 0x0>;
+			dma-coherent;
+
+			bus-width = <8>;
+
+			qcom,dll-config = <0x0007642c>;
+			qcom,ddr-config = <0x80040868>;
+
+			status = "disabled";
+
+			sdhc1_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+					opp-peak-kBps = <6528000 1652800>;
+					opp-avg-kBps = <400000 0>;
+				};
+			};
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,qdu1000-pdc", "qcom,pdc";
 			reg = <0x0 0xb220000 0x0 0x30000>, <0x0 0x174000f0 0x0 0x64>;
@@ -1100,6 +1147,69 @@ qup_spi15_cs: qup-spi15-cs-state {
 				pins = "gpio31";
 				function = "gpio";
 			};
+
+			sdc_on_state: sdc-on-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				rclk-pins {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+
+			sdc_off_state: sdc-off-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				rclk-pins {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+		};
+
+		sram@14680000 {
+			compatible = "qcom,qdu1000-imem", "syscon", "simple-mfd";
+			reg = <0 0x14680000 0 0x1000>;
+			ranges = <0 0 0x14680000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pil-reloc@94c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x94c 0xc8>;
+			};
 		};
 
 		apps_smmu: iommu@15000000 {
@@ -1242,6 +1352,7 @@ apps_rsc: rsc@17a00000 {
 			qcom,tcs-config = <ACTIVE_TCS    2>, <SLEEP_TCS     3>,
 					  <WAKE_TCS      3>, <CONTROL_TCS   0>;
 			label = "apps_rsc";
+			power-domains = <&CLUSTER_PD>;
 
 			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";

arch/arm64/boot/dts/qcom/qrb4210-rb2.dts

@@ -7,6 +7,7 @@
 
 #include <dt-bindings/leds/common.h>
 #include "sm4250.dtsi"
+#include "pm6125.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. QRB4210 RB2";
@@ -28,6 +29,23 @@ clk40M: can-clk {
 		};
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "gpio-keys";
+
+		pinctrl-0 = <&kypd_vol_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
 	hdmi-connector {
 		compatible = "hdmi-connector";
 		type = "a";
@@ -219,6 +237,25 @@ &mdss_dsi0_phy {
 	status = "okay";
 };
 
+&pm6125_gpios {
+	kypd_vol_up_n: kypd-vol-up-n-state {
+		pins = "gpio5";
+		function = "normal";
+		power-source = <0>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/qrb5165-rb5.dts

@@ -535,30 +535,6 @@ &cdsp {
 	firmware-name = "qcom/sm8250/cdsp.mbn";
 };
 
-&dsi0 {
-	status = "okay";
-	vdda-supply = <&vreg_l9a_1p2>;
-
-#if 0
-	qcom,dual-dsi-mode;
-	qcom,master-dsi;
-#endif
-
-	ports {
-		port@1 {
-			endpoint {
-				remote-endpoint = <&lt9611_a>;
-				data-lanes = <0 1 2 3>;
-			};
-		};
-	};
-};
-
-&dsi0_phy {
-	status = "okay";
-	vdds-supply = <&vreg_l5a_0p88>;
-};
-
 &gmu {
 	status = "okay";
 };
@@ -604,7 +580,7 @@ port@0 {
 				reg = <0>;
 
 				lt9611_a: endpoint {
-					remote-endpoint = <&dsi0_out>;
+					remote-endpoint = <&mdss_dsi0_out>;
 				};
 			};
 
@@ -613,7 +589,7 @@ port@1 {
 				reg = <1>;
 
 				lt9611_b: endpoint {
-					remote-endpoint = <&dsi1_out>;
+					remote-endpoint = <&mdss_dsi1_out>;
 				};
 			};
 #endif
@@ -639,8 +615,28 @@ &mdss {
 	status = "okay";
 };
 
-&mdss_mdp {
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l9a_1p2>;
+
+#if 0
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+#endif
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_phy {
 	status = "okay";
+	vdds-supply = <&vreg_l5a_0p88>;
 };
 
 &pm8150_adc {

arch/arm64/boot/dts/qcom/sa8540p-ride.dts

@@ -171,6 +171,7 @@ mdio {
 
 		/* Marvell 88EA1512 */
 		rgmii_phy: phy@8 {
+			compatible = "ethernet-phy-id0141.0dd4";
 			reg = <0x8>;
 
 			interrupts-extended = <&tlmm 127 IRQ_TYPE_EDGE_FALLING>;

arch/arm64/boot/dts/qcom/sa8540p.dtsi

@@ -167,6 +167,14 @@ opp-2592000000 {
 	};
 };
 
+&gpucc {
+	status = "disabled";
+};
+
+&gpu_smmu {
+	status = "disabled";
+};
+
 &pcie2a {
 	compatible = "qcom,pcie-sa8540p";
 

arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts

@@ -143,21 +143,6 @@ reg_tp_3p3: touchpad-regulator {
 	};
 };
 
-&dsi0 {
-	vdda-supply = <&vreg_l3c_1p2>;
-	status = "okay";
-};
-
-&dsi0_out {
-	remote-endpoint = <&sn65dsi86_in>;
-	data-lanes = <0 1 2 3>;
-};
-
-&dsi_phy {
-	vdds-supply = <&vreg_l4a_0p8>;
-	status = "okay";
-};
-
 &i2c2 {
 	clock-frequency = <400000>;
 	status = "okay";
@@ -269,7 +254,7 @@ port@0 {
 				reg = <0>;
 
 				sn65dsi86_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
+					remote-endpoint = <&mdss_dsi0_out>;
 				};
 			};
 
@@ -313,6 +298,21 @@ &mdss {
 	status = "okay";
 };
 
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3c_1p2>;
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&sn65dsi86_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l4a_0p8>;
+	status = "okay";
+};
+
 &pm6150_adc {
 	thermistor@4e {
 		reg = <ADC5_AMUX_THM2_100K_PU>;

arch/arm64/boot/dts/qcom/sc7180-idp.dts

@@ -295,7 +295,11 @@ vreg_bob: bob {
 	};
 };
 
-&dsi0 {
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
 	status = "okay";
 
 	vdda-supply = <&vreg_l3c_1p2>;
@@ -314,7 +318,7 @@ panel@0 {
 
 		port {
 			panel0_in: endpoint {
-				remote-endpoint = <&dsi0_out>;
+				remote-endpoint = <&mdss_dsi0_out>;
 			};
 		};
 	};
@@ -329,15 +333,11 @@ endpoint {
 	};
 };
 
-&dsi_phy {
+&mdss_dsi0_phy {
 	status = "okay";
 	vdds-supply = <&vreg_l4a_0p8>;
 };
 
-&mdss {
-	status = "okay";
-};
-
 &qfprom {
 	vcc-supply = <&vreg_l11a_1p8>;
 };

arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi

@@ -46,10 +46,6 @@ &pp3300_dx_edp {
 
 /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
 
-&dsi0_out {
-	remote-endpoint = <&ps8640_in>;
-};
-
 edp_brij_i2c: &i2c2 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -74,7 +70,7 @@ ports {
 			port@0 {
 				reg = <0>;
 				ps8640_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
+					remote-endpoint = <&mdss_dsi0_out>;
 				};
 			};
 
@@ -102,6 +98,10 @@ panel_in_edp: endpoint {
 	};
 };
 
+&mdss_dsi0_out {
+	remote-endpoint = <&ps8640_in>;
+};
+
 &tlmm {
 	edp_brij_ps8640_rst: edp-brij-ps8640-rst-state {
 		pins = "gpio11";

arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts

@@ -15,7 +15,7 @@ / {
 	compatible = "google,quackingstick-sku1537", "qcom,sc7180";
 };
 
-&dsi_phy {
+&mdss_dsi0_phy {
 	qcom,phy-rescode-offset-top = /bits/ 8 <(-13) (-13) (-13) (-13) (-13)>;
 	qcom,phy-rescode-offset-bot = /bits/ 8 <(-13) (-13) (-13) (-13) (-13)>;
 	qcom,phy-drive-ldo-level = <375>;

arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi

@@ -52,7 +52,31 @@ keyboard-controller {
 	};
 };
 
-&dsi0 {
+&gpio_keys {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+	};
+};
+
+&mdss_dsi0 {
 	panel: panel@0 {
 		/* Compatible will be filled in per-board */
 		reg = <0>;
@@ -67,7 +91,7 @@ panel: panel@0 {
 
 		port {
 			panel_in: endpoint {
-				remote-endpoint = <&dsi0_out>;
+				remote-endpoint = <&mdss_dsi0_out>;
 			};
 		};
 	};
@@ -82,30 +106,6 @@ endpoint {
 	};
 };
 
-&gpio_keys {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	ap_ts: touchscreen@10 {
-		compatible = "hid-over-i2c";
-		reg = <0x10>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
-
-		post-power-on-delay-ms = <20>;
-		hid-descr-addr = <0x0001>;
-
-		vdd-supply = <&pp3300_ts>;
-	};
-};
-
 &sdhc_2 {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi

@@ -27,10 +27,6 @@ &pp3300_dx_edp {
 
 /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
 
-&dsi0_out {
-	remote-endpoint = <&sn65dsi86_in>;
-};
-
 edp_brij_i2c: &i2c2 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -65,7 +61,7 @@ ports {
 			port@0 {
 				reg = <0>;
 				sn65dsi86_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
+					remote-endpoint = <&mdss_dsi0_out>;
 				};
 			};
 
@@ -95,6 +91,10 @@ panel_in_edp: endpoint {
 	};
 };
 
+&mdss_dsi0_out {
+	remote-endpoint = <&sn65dsi86_in>;
+};
+
 &tlmm {
 	edp_brij_irq: edp-brij-irq-state {
 		pins = "gpio11";

arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe.dts

@@ -17,7 +17,7 @@ / {
 	compatible = "google,wormdingler-sku1024", "qcom,sc7180";
 };
 
-&dsi_phy {
+&mdss_dsi0_phy {
 	qcom,phy-rescode-offset-top = /bits/ 8 <31 31 31 31 (-32)>;
 	qcom,phy-rescode-offset-bot = /bits/ 8 <31 31 31 31 (-32)>;
 	qcom,phy-drive-ldo-level = <450>;

arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi

@@ -110,7 +110,28 @@ keyboard-controller {
 	};
 };
 
-&dsi0 {
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@1 {
+		compatible = "hid-over-i2c";
+		reg = <0x01>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+		post-power-on-delay-ms = <70>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+		vddl-supply = <&pp1800_ts>;
+	};
+};
+
+&mdss_dsi0 {
 
 	panel: panel@0 {
 		reg = <0>;
@@ -126,7 +147,7 @@ panel: panel@0 {
 
 		port {
 			panel_in: endpoint {
-				remote-endpoint = <&dsi0_out>;
+				remote-endpoint = <&mdss_dsi0_out>;
 			};
 		};
 	};
@@ -141,27 +162,6 @@ endpoint {
 	};
 };
 
-&i2c4 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	ap_ts: touchscreen@1 {
-		compatible = "hid-over-i2c";
-		reg = <0x01>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_int_l>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
-
-		post-power-on-delay-ms = <70>;
-		hid-descr-addr = <0x0001>;
-
-		vdd-supply = <&pp3300_ts>;
-		vddl-supply = <&pp1800_ts>;
-	};
-};
-
 &pm6150_adc {
 	skin-temp-thermistor@4d {
 		reg = <ADC5_AMUX_THM1_100K_PU>;

arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi

@@ -705,20 +705,6 @@ &camcc {
 	status = "disabled";
 };
 
-&dsi0 {
-	status = "okay";
-	vdda-supply = <&vdda_mipi_dsi0_1p2>;
-};
-
-&dsi0_out {
-	data-lanes = <0 1 2 3>;
-};
-
-&dsi_phy {
-	status = "okay";
-	vdds-supply = <&vdda_mipi_dsi0_pll>;
-};
-
 ap_sar_sensor_i2c: &i2c5 {
 	clock-frequency = <400000>;
 
@@ -836,6 +822,20 @@ &mdss_dp_out {
 	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
 };
 
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vdda_mipi_dsi0_1p2>;
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
 &pm6150_adc {
 	charger-thermistor@4f {
 		reg = <ADC5_AMUX_THM3_100K_PU>;

arch/arm64/boot/dts/qcom/sc7180.dtsi

@@ -2996,7 +2996,7 @@ ports {
 					port@0 {
 						reg = <0>;
 						dpu_intf1_out: endpoint {
-							remote-endpoint = <&dsi0_in>;
+							remote-endpoint = <&mdss_dsi0_in>;
 						};
 					};
 
@@ -3033,7 +3033,7 @@ opp-460000000 {
 				};
 			};
 
-			dsi0: dsi@ae94000 {
+			mdss_dsi0: dsi@ae94000 {
 				compatible = "qcom,sc7180-dsi-ctrl",
 					     "qcom,mdss-dsi-ctrl";
 				reg = <0 0x0ae94000 0 0x400>;
@@ -3056,12 +3056,12 @@ dsi0: dsi@ae94000 {
 					      "bus";
 
 				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
-				assigned-clock-parents = <&dsi_phy 0>, <&dsi_phy 1>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
 
 				operating-points-v2 = <&dsi_opp_table>;
 				power-domains = <&rpmhpd SC7180_CX>;
 
-				phys = <&dsi_phy>;
+				phys = <&mdss_dsi0_phy>;
 
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3074,14 +3074,14 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi0_in: endpoint {
+						mdss_dsi0_in: endpoint {
 							remote-endpoint = <&dpu_intf1_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi0_out: endpoint {
+						mdss_dsi0_out: endpoint {
 						};
 					};
 				};
@@ -3106,13 +3106,13 @@ opp-358000000 {
 				};
 			};
 
-			dsi_phy: phy@ae94400 {
+			mdss_dsi0_phy: phy@ae94400 {
 				compatible = "qcom,dsi-phy-10nm";
 				reg = <0 0x0ae94400 0 0x200>,
 				      <0 0x0ae94600 0 0x280>,
 				      <0 0x0ae94a00 0 0x1e0>;
-				reg-names = "dsi_phy",
-					    "dsi_phy_lane",
+				reg-names = "dsi0_phy",
+					    "dsi0_phy_lane",
 					    "dsi_pll";
 
 				#clock-cells = <1>;
@@ -3203,8 +3203,8 @@ dispcc: clock-controller@af00000 {
 			reg = <0 0x0af00000 0 0x200000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 				 <&gcc GCC_DISP_GPLL0_CLK_SRC>,
-				 <&dsi_phy 0>,
-				 <&dsi_phy 1>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi0_phy 1>,
 				 <&dp_phy 0>,
 				 <&dp_phy 1>;
 			clock-names = "bi_tcxo",

arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi

@@ -467,10 +467,6 @@ &mdss_dp_out {
 	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
 };
 
-&mdss_mdp {
-	status = "okay";
-};
-
 /* NVMe drive, enabled on a per-board basis */
 &pcie1 {
 	pinctrl-names = "default";

arch/arm64/boot/dts/qcom/sc7280.dtsi

@@ -3872,8 +3872,6 @@ mdss_mdp: display-controller@ae01000 {
 				interrupt-parent = <&mdss>;
 				interrupts = <0>;
 
-				status = "disabled";
-
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -3881,7 +3879,7 @@ ports {
 					port@0 {
 						reg = <0>;
 						dpu_intf1_out: endpoint {
-							remote-endpoint = <&dsi0_in>;
+							remote-endpoint = <&mdss_dsi0_in>;
 						};
 					};
 
@@ -3966,14 +3964,14 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi0_in: endpoint {
+						mdss_dsi0_in: endpoint {
 							remote-endpoint = <&dpu_intf1_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi0_out: endpoint {
+						mdss_dsi0_out: endpoint {
 						};
 					};
 				};

arch/arm64/boot/dts/qcom/sc8180x-primus.dts

@@ -291,10 +291,6 @@ vreg_l16e_3p0: ldo16 {
 	};
 };
 
-&dispcc {
-	status = "okay";
-};
-
 &gpu {
 	status = "okay";
 

arch/arm64/boot/dts/qcom/sc8180x.dtsi

@@ -2310,7 +2310,8 @@ gpucc: clock-controller@2c90000 {
 		};
 
 		adreno_smmu: iommu@2ca0000 {
-			compatible = "qcom,sc8180x-smmu-500", "arm,mmu-500";
+			compatible = "qcom,sc8180x-smmu-500", "qcom,adreno-smmu",
+				     "qcom,smmu-500", "arm,mmu-500";
 			reg = <0 0x02ca0000 0 0x10000>;
 			#iommu-cells = <2>;
 			#global-interrupts = <1>;
@@ -2732,14 +2733,14 @@ dpu_intf0_out: endpoint {
 					port@1 {
 						reg = <1>;
 						dpu_intf1_out: endpoint {
-							remote-endpoint = <&dsi0_in>;
+							remote-endpoint = <&mdss_dsi0_in>;
 						};
 					};
 
 					port@2 {
 						reg = <2>;
 						dpu_intf2_out: endpoint {
-							remote-endpoint = <&dsi1_in>;
+							remote-endpoint = <&mdss_dsi1_in>;
 						};
 					};
 
@@ -2783,7 +2784,7 @@ opp-460000000 {
 				};
 			};
 
-			dsi0: dsi@ae94000 {
+			mdss_dsi0: dsi@ae94000 {
 				compatible = "qcom,mdss-dsi-ctrl";
 				reg = <0 0x0ae94000 0 0x400>;
 				reg-names = "dsi_ctrl";
@@ -2807,7 +2808,7 @@ dsi0: dsi@ae94000 {
 				operating-points-v2 = <&dsi_opp_table>;
 				power-domains = <&rpmhpd SC8180X_MMCX>;
 
-				phys = <&dsi0_phy>;
+				phys = <&mdss_dsi0_phy>;
 				phy-names = "dsi";
 
 				status = "disabled";
@@ -2818,14 +2819,14 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi0_in: endpoint {
+						mdss_dsi0_in: endpoint {
 							remote-endpoint = <&dpu_intf1_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi0_out: endpoint {
+						mdss_dsi0_out: endpoint {
 						};
 					};
 				};
@@ -2850,7 +2851,7 @@ opp-358000000 {
 				};
 			};
 
-			dsi0_phy: dsi-phy@ae94400 {
+			mdss_dsi0_phy: dsi-phy@ae94400 {
 				compatible = "qcom,dsi-phy-7nm";
 				reg = <0 0x0ae94400 0 0x200>,
 				      <0 0x0ae94600 0 0x280>,
@@ -2869,7 +2870,7 @@ dsi0_phy: dsi-phy@ae94400 {
 				status = "disabled";
 			};
 
-			dsi1: dsi@ae96000 {
+			mdss_dsi1: dsi@ae96000 {
 				compatible = "qcom,mdss-dsi-ctrl";
 				reg = <0 0x0ae96000 0 0x400>;
 				reg-names = "dsi_ctrl";
@@ -2893,7 +2894,7 @@ dsi1: dsi@ae96000 {
 				operating-points-v2 = <&dsi_opp_table>;
 				power-domains = <&rpmhpd SC8180X_MMCX>;
 
-				phys = <&dsi1_phy>;
+				phys = <&mdss_dsi1_phy>;
 				phy-names = "dsi";
 
 				status = "disabled";
@@ -2904,20 +2905,20 @@ ports {
 
 					port@0 {
 						reg = <0>;
-						dsi1_in: endpoint {
+						mdss_dsi1_in: endpoint {
 							remote-endpoint = <&dpu_intf2_out>;
 						};
 					};
 
 					port@1 {
 						reg = <1>;
-						dsi1_out: endpoint {
+						mdss_dsi1_out: endpoint {
 						};
 					};
 				};
 			};
 
-			dsi1_phy: dsi-phy@ae96400 {
+			mdss_dsi1_phy: dsi-phy@ae96400 {
 				compatible = "qcom,dsi-phy-7nm";
 				reg = <0 0x0ae96400 0 0x200>,
 				      <0 0x0ae96600 0 0x280>,
@@ -2965,7 +2966,7 @@ mdss_dp0: displayport-controller@ae90000 {
 				#sound-dai-cells = <0>;
 
 				operating-points-v2 = <&dp0_opp_table>;
-				power-domains = <&rpmhpd SC8180X_CX>;
+				power-domains = <&rpmhpd SC8180X_MMCX>;
 
 				status = "disabled";
 
@@ -3039,7 +3040,7 @@ mdss_dp1: displayport-controller@ae98000 {
 				#sound-dai-cells = <0>;
 
 				operating-points-v2 = <&dp0_opp_table>;
-				power-domains = <&rpmhpd SC8180X_CX>;
+				power-domains = <&rpmhpd SC8180X_MMCX>;
 
 				status = "disabled";
 
@@ -3113,7 +3114,7 @@ mdss_edp: displayport-controller@ae9a000 {
 				#sound-dai-cells = <0>;
 
 				operating-points-v2 = <&edp_opp_table>;
-				power-domains = <&rpmhpd SC8180X_CX>;
+				power-domains = <&rpmhpd SC8180X_MMCX>;
 
 				status = "disabled";
 
@@ -3495,6 +3496,7 @@ apps_rsc: rsc@18200000 {
 					  <WAKE_TCS    1>,
 					  <CONTROL_TCS 0>;
 			label = "apps_rsc";
+			power-domains = <&CLUSTER_PD>;
 
 			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";

arch/arm64/boot/dts/qcom/sc8280xp-crd.dts

@@ -210,6 +210,11 @@ vreg_wwan: regulator-wwan {
 	};
 
 	reserved-memory {
+		gpu_mem: gpu-mem@8bf00000 {
+			reg = <0 0x8bf00000 0 0x2000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			size = <0x0 0x8000000>;
@@ -390,6 +395,15 @@ &dispcc0 {
 	status = "okay";
 };
 
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sc8280xp/qcdxkmsuc8280.mbn";
+	};
+};
+
 &mdss0 {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/sdm670.dtsi

@@ -1264,6 +1264,7 @@ apps_rsc: rsc@179c0000 {
 					  <SLEEP_TCS   3>,
 					  <WAKE_TCS    3>,
 					  <CONTROL_TCS 1>;
+			power-domains = <&CLUSTER_PD>;
 
 			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";

arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts

@@ -51,6 +51,10 @@ max98927_codec: max98927@3a {
 	};
 };
 
+&pmi8998_charger {
+	monitored-battery = <&battery>;
+};
+
 &sound {
 	model = "OnePlus 6";
 	audio-routing =	"RX_BIAS", "MCLK",