Commit 065f5f68 authored by Carl Huang's avatar Carl Huang Committed by Kalle Valo

ath11k: use TCL_DATA_RING_0 for QCA6390

For QCA6390, wbm2sw1 is used for other purpose rather than
tx completion ring. So use TCL_DATA_RING 0 only for QCA6390.

Add MISC_CAPS_TCL_0_ONLY to control it.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: default avatarCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: default avatarKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-9-git-send-email-kvalo@codeaurora.org
parent 454a9721
......@@ -42,6 +42,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.rx_mac_buf_ring = false,
.vdev_start_delay = false,
.htt_peer_map_v2 = true,
.tcl_0_only = false,
},
{
.name = "qca6390 hw2.0",
......@@ -66,6 +67,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.rx_mac_buf_ring = true,
.vdev_start_delay = true,
.htt_peer_map_v2 = false,
.tcl_0_only = true,
},
};
......
......@@ -110,7 +110,12 @@ int ath11k_dp_tx(struct ath11k *ar, struct ath11k_vif *arvif,
tcl_ring_sel:
tcl_ring_retry = false;
ti.ring_id = ring_selector % DP_TCL_NUM_RING_MAX;
/* For some chip, it can only use tcl0 to tx */
if (ar->ab->hw_params.tcl_0_only)
ti.ring_id = 0;
else
ti.ring_id = ring_selector % DP_TCL_NUM_RING_MAX;
ring_map |= BIT(ti.ring_id);
tx_ring = &dp->tx_ring[ti.ring_id];
......@@ -221,7 +226,8 @@ int ath11k_dp_tx(struct ath11k *ar, struct ath11k_vif *arvif,
* checking this ring earlier for each pkt tx.
* Restart ring selection if some rings are not checked yet.
*/
if (ring_map != (BIT(DP_TCL_NUM_RING_MAX) - 1)) {
if (ring_map != (BIT(DP_TCL_NUM_RING_MAX) - 1) &&
!ar->ab->hw_params.tcl_0_only) {
tcl_ring_retry = true;
ring_selector++;
}
......
......@@ -151,6 +151,7 @@ struct ath11k_hw_params {
bool rx_mac_buf_ring;
bool vdev_start_delay;
bool htt_peer_map_v2;
bool tcl_0_only;
};
struct ath11k_hw_ops {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment