Commit 06aaa3d0 authored by Christophe Leroy's avatar Christophe Leroy Committed by Greg Kroah-Hartman

tty: serial: cpm_uart - fix init when SMC is relocated

SMC relocation can also be activated earlier by the bootloader,
so the driver's behaviour cannot rely on selected kernel config.

When the SMC is relocated, CPM_CR_INIT_TRX cannot be used.

But the only thing CPM_CR_INIT_TRX does is to clear the
rstate and tstate registers, so this can be done manually,
even when SMC is not relocated.
Signed-off-by: default avatarChristophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9ab92120 ("cpm_uart: fix non-console port startup bug")
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 2c58e560
......@@ -407,7 +407,16 @@ static int cpm_uart_startup(struct uart_port *port)
clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_RX);
}
cpm_uart_initbd(pinfo);
cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
if (IS_SMC(pinfo)) {
out_be32(&pinfo->smcup->smc_rstate, 0);
out_be32(&pinfo->smcup->smc_tstate, 0);
out_be16(&pinfo->smcup->smc_rbptr,
in_be16(&pinfo->smcup->smc_rbase));
out_be16(&pinfo->smcup->smc_tbptr,
in_be16(&pinfo->smcup->smc_tbase));
} else {
cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
}
}
/* Install interrupt handler. */
retval = request_irq(port->irq, cpm_uart_int, 0, "cpm_uart", port);
......@@ -861,16 +870,14 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo)
(u8 __iomem *)pinfo->tx_bd_base - DPRAM_BASE);
/*
* In case SMC1 is being relocated...
* In case SMC is being relocated...
*/
#if defined (CONFIG_I2C_SPI_SMC1_UCODE_PATCH)
out_be16(&up->smc_rbptr, in_be16(&pinfo->smcup->smc_rbase));
out_be16(&up->smc_tbptr, in_be16(&pinfo->smcup->smc_tbase));
out_be32(&up->smc_rstate, 0);
out_be32(&up->smc_tstate, 0);
out_be16(&up->smc_brkcr, 1); /* number of break chars */
out_be16(&up->smc_brkec, 0);
#endif
/* Set up the uart parameters in the
* parameter ram.
......@@ -884,8 +891,6 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo)
out_be16(&up->smc_brkec, 0);
out_be16(&up->smc_brkcr, 1);
cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment