Merge branch 'vexpress-clk-soc' of git://git.linaro.org/people/pawelmoll/linux into next/soc

From Pawel Moll:
* 'vexpress-clk-soc' of git://git.linaro.org/people/pawelmoll/linux:
  ARM: vexpress: Remove motherboard dependencies in the DTS files
  ARM: vexpress: Start using new Versatile Express infrastructure
  ARM: vexpress: Add config bus components and clocks to DTs
  mfd: Versatile Express system registers driver
  mfd: Versatile Express config infrastructure

Documentation/devicetree/bindings/arm/vexpress-sysreg.txt

+ARM Versatile Express system registers
+--------------------------------------
+
+This is a system control registers block, providing multiple low level
+platform functions like board detection and identification, software
+interrupt generation, MMC and NOR Flash control etc.
+
+Required node properties:
+- compatible value : = "arm,vexpress,sysreg";
+- reg : physical base address and the size of the registers window
+- gpio-controller : specifies that the node is a GPIO controller
+- #gpio-cells : size of the GPIO specifier, should be 2:
+  - first cell is the pseudo-GPIO line number:
+    0 - MMC CARDIN
+    1 - MMC WPROT
+    2 - NOR FLASH WPn
+  - second cell can take standard GPIO flags (currently ignored).
+
+Example:
+	v2m_sysreg: sysreg@10000000 {
+ 		compatible = "arm,vexpress-sysreg";
+ 		reg = <0x10000000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+ 	};
+
+This block also can also act a bridge to the platform's configuration
+bus via "system control" interface, addressing devices with site number,
+position in the board stack, config controller, function and device
+numbers - see motherboard's TRM for more details.
+
+The node describing a config device must refer to the sysreg node via
+"arm,vexpress,config-bridge" phandle (can be also defined in the node's
+parent) and relies on the board topology properties - see main vexpress
+node documentation for more details. It must must also define the
+following property:
+- arm,vexpress-sysreg,func : must contain two cells:
+  - first cell defines function number (eg. 1 for clock generator,
+    2 for voltage regulators etc.)
+  - device number (eg. osc 0, osc 1 etc.)
+
+Example:
+	mcc {
+		arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+		osc@0 {
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 0>;
+		};
+	};

Documentation/devicetree/bindings/arm/vexpress.txt

@@ -11,6 +11,10 @@ the motherboard file using a /include/ directive. As the motherboard
 can be initialized in one of two different configurations ("memory
 maps"), care must be taken to include the correct one.
 
+
+Root node
+---------
+
 Required properties in the root node:
 - compatible value:
 	compatible = "arm,vexpress,<model>", "arm,vexpress";
@@ -45,6 +49,10 @@ Optional properties in the root node:
   - Coretile Express A9x4 (V2P-CA9) HBI-0225:
 	arm,hbi = <0x225>;
 
+
+CPU nodes
+---------
+
 Top-level standard "cpus" node is required. It must contain a node
 with device_type = "cpu" property for every available core, eg.:
 
@@ -59,6 +67,52 @@ with device_type = "cpu" property for every available core, eg.:
 		};
 	};
 
+
+Configuration infrastructure
+----------------------------
+
+The platform has an elaborated configuration system, consisting of
+microcontrollers residing on the mother- and daughterboards known
+as Motherboard/Daughterboard Configuration Controller (MCC and DCC).
+The controllers are responsible for the platform initialization
+(reset generation, flash programming, FPGA bitfiles loading etc.)
+but also control clock generators, voltage regulators, gather
+environmental data like temperature, power consumption etc. Even
+the video output switch (FPGA) is controlled that way.
+
+Nodes describing devices controlled by this infrastructure should
+point at the bridge device node:
+- bridge phandle:
+	arm,vexpress,config-bridge = <phandle>;
+This property can be also defined in a parent node (eg. for a DCC)
+and is effective for all children.
+
+
+Platform topology
+-----------------
+
+As Versatile Express can be configured in number of physically
+different setups, the device tree should describe platform topology.
+Root node and main motherboard node must define the following
+property, describing physical location of the children nodes:
+- site number:
+	arm,vexpress,site = <number>;
+  where 0 means motherboard, 1 or 2 are daugtherboard sites,
+  0xf means "master" site (site containing main CPU tile)
+- when daughterboards are stacked on one site, their position
+  in the stack be be described with:
+	arm,vexpress,position = <number>;
+- when describing tiles consisting more than one DCC, its number
+  can be described with:
+	arm,vexpress,dcc = <number>;
+
+Any of the numbers above defaults to zero if not defined in
+the node or any of its parent.
+
+
+Motherboard
+-----------
+
 The motherboard description file provides a single "motherboard" node
 using 2 address cells corresponding to the Static Memory Bus used
 between the motherboard and the tile. The first cell defines the Chip
@@ -87,22 +141,30 @@ can be used to obtain required phandle in the tile's "aliases" node:
 - SP804 timers:
 	v2m_timer01 and v2m_timer23
 
-Current Linux implementation requires a "arm,v2m_timer" alias
-pointing at one of the motherboard's SP804 timers, if it is to be
-used as the system timer. This alias should be defined in the
-motherboard files.
+The tile description should define a "smb" node, describing the
+Static Memory Bus between the tile and motherboard. It must define
+the following properties:
+- "simple-bus" compatible value (to ensure creation of the children)
+	compatible = "simple-bus";
+- mapping of the SMB CS/offset addresses into main address space:
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <...>;
+- interrupts mapping:
+	#interrupt-cells = <1>;
+	interrupt-map-mask = <0 0 63>;
+	interrupt-map = <...>;
 
-The tile description must define "ranges", "interrupt-map-mask" and
-"interrupt-map" properties to translate the motherboard's address
-and interrupt space into one used by the tile's processor.
 
-Abbreviated example:
+Example of a VE tile description (simplified)
+---------------------------------------------
 
 /dts-v1/;
 
 / {
 	model = "V2P-CA5s";
 	arm,hbi = <0x225>;
+	arm,vexpress,site = <0xf>;
 	compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress";
 	interrupt-parent = <&gic>;
 	#address-cells = <1>;
@@ -134,13 +196,29 @@ Abbreviated example:
 		      <0x2c000100 0x100>;
 	};
 
-	motherboard {
+	dcc {
+		compatible = "simple-bus";
+		arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+		osc@0 {
+			compatible = "arm,vexpress-osc";
+		};
+	};
+
+	smb {
+		compatible = "simple-bus";
+
+		#address-cells = <2>;
+		#size-cells = <1>;
 		/* CS0 is visible at 0x08000000 */
 		ranges = <0 0 0x08000000 0x04000000>;
+
+		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 63>;
 		/* Active high IRQ 0 is connected to GIC's SPI0 */
 		interrupt-map = <0 0 0 &gic 0 0 4>;
+
+		/include/ "vexpress-v2m-rs1.dtsi"
 	};
 };
 
-/include/ "vexpress-v2m-rs1.dtsi"

arch/arm/boot/dts/vexpress-v2m-rs1.dtsi

@@ -17,17 +17,16 @@
  * CHANGES TO vexpress-v2m.dtsi!
  */
 
-/ {
-	aliases {
-		arm,v2m_timer = &v2m_timer01;
-	};
-
 	motherboard {
-		compatible = "simple-bus";
+		model = "V2M-P1";
+		arm,hbi = <0x190>;
+		arm,vexpress,site = <0>;
 		arm,v2m-memory-map = "rs1";
+		compatible = "arm,vexpress,v2m-p1", "simple-bus";
 		#address-cells = <2>; /* SMB chipselect number and offset */
 		#size-cells = <1>;
 		#interrupt-cells = <1>;
+		ranges;
 
 		flash@0,00000000 {
 			compatible = "arm,vexpress-flash", "cfi-flash";
@@ -72,14 +71,20 @@ iofpga@3,00000000 {
 			#size-cells = <1>;
 			ranges = <0 3 0 0x200000>;
 
-			sysreg@010000 {
+			v2m_sysreg: sysreg@010000 {
 				compatible = "arm,vexpress-sysreg";
 				reg = <0x010000 0x1000>;
+				gpio-controller;
+				#gpio-cells = <2>;
 			};
 
-			sysctl@020000 {
+			v2m_sysctl: sysctl@020000 {
 				compatible = "arm,sp810", "arm,primecell";
 				reg = <0x020000 0x1000>;
+				clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>;
+				clock-names = "refclk", "timclk", "apb_pclk";
+				#clock-cells = <1>;
+				clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
 			};
 
 			/* PCI-E I2C bus */
@@ -100,66 +105,92 @@ aaci@040000 {
 				compatible = "arm,pl041", "arm,primecell";
 				reg = <0x040000 0x1000>;
 				interrupts = <11>;
+				clocks = <&smbclk>;
+				clock-names = "apb_pclk";
 			};
 
 			mmci@050000 {
 				compatible = "arm,pl180", "arm,primecell";
 				reg = <0x050000 0x1000>;
 				interrupts = <9 10>;
+				cd-gpios = <&v2m_sysreg 0 0>;
+				wp-gpios = <&v2m_sysreg 1 0>;
+				max-frequency = <12000000>;
+				vmmc-supply = <&v2m_fixed_3v3>;
+				clocks = <&v2m_clk24mhz>, <&smbclk>;
+				clock-names = "mclk", "apb_pclk";
 			};
 
 			kmi@060000 {
 				compatible = "arm,pl050", "arm,primecell";
 				reg = <0x060000 0x1000>;
 				interrupts = <12>;
+				clocks = <&v2m_clk24mhz>, <&smbclk>;
+				clock-names = "KMIREFCLK", "apb_pclk";
 			};
 
 			kmi@070000 {
 				compatible = "arm,pl050", "arm,primecell";
 				reg = <0x070000 0x1000>;
 				interrupts = <13>;
+				clocks = <&v2m_clk24mhz>, <&smbclk>;
+				clock-names = "KMIREFCLK", "apb_pclk";
 			};
 
 			v2m_serial0: uart@090000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x090000 0x1000>;
 				interrupts = <5>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			v2m_serial1: uart@0a0000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x0a0000 0x1000>;
 				interrupts = <6>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			v2m_serial2: uart@0b0000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x0b0000 0x1000>;
 				interrupts = <7>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			v2m_serial3: uart@0c0000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x0c0000 0x1000>;
 				interrupts = <8>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			wdt@0f0000 {
 				compatible = "arm,sp805", "arm,primecell";
 				reg = <0x0f0000 0x1000>;
 				interrupts = <0>;
+				clocks = <&v2m_refclk32khz>, <&smbclk>;
+				clock-names = "wdogclk", "apb_pclk";
 			};
 
 			v2m_timer01: timer@110000 {
 				compatible = "arm,sp804", "arm,primecell";
 				reg = <0x110000 0x1000>;
 				interrupts = <2>;
+				clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
+				clock-names = "timclken1", "timclken2", "apb_pclk";
 			};
 
 			v2m_timer23: timer@120000 {
 				compatible = "arm,sp804", "arm,primecell";
 				reg = <0x120000 0x1000>;
 				interrupts = <3>;
+				clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>;
+				clock-names = "timclken1", "timclken2", "apb_pclk";
 			};
 
 			/* DVI I2C bus */
@@ -185,6 +216,8 @@ rtc@170000 {
 				compatible = "arm,pl031", "arm,primecell";
 				reg = <0x170000 0x1000>;
 				interrupts = <4>;
+				clocks = <&smbclk>;
+				clock-names = "apb_pclk";
 			};
 
 			compact-flash@1a0000 {
@@ -198,6 +231,8 @@ clcd@1f0000 {
 				compatible = "arm,pl111", "arm,primecell";
 				reg = <0x1f0000 0x1000>;
 				interrupts = <14>;
+				clocks = <&v2m_oscclk1>, <&smbclk>;
+				clock-names = "clcdclk", "apb_pclk";
 			};
 		};
 
@@ -208,5 +243,98 @@ v2m_fixed_3v3: fixedregulator@0 {
 			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
+
+		v2m_clk24mhz: clk24mhz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+			clock-output-names = "v2m:clk24mhz";
+		};
+
+		v2m_refclk1mhz: refclk1mhz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1000000>;
+			clock-output-names = "v2m:refclk1mhz";
+		};
+
+		v2m_refclk32khz: refclk32khz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "v2m:refclk32khz";
+		};
+
+		mcc {
+			compatible = "arm,vexpress,config-bus";
+			arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+			osc@0 {
+				/* MCC static memory clock */
+				compatible = "arm,vexpress-osc";
+				arm,vexpress-sysreg,func = <1 0>;
+				freq-range = <25000000 60000000>;
+				#clock-cells = <0>;
+				clock-output-names = "v2m:oscclk0";
+			};
+
+			v2m_oscclk1: osc@1 {
+				/* CLCD clock */
+				compatible = "arm,vexpress-osc";
+				arm,vexpress-sysreg,func = <1 1>;
+				freq-range = <23750000 63500000>;
+				#clock-cells = <0>;
+				clock-output-names = "v2m:oscclk1";
+			};
+
+			v2m_oscclk2: osc@2 {
+				/* IO FPGA peripheral clock */
+				compatible = "arm,vexpress-osc";
+				arm,vexpress-sysreg,func = <1 2>;
+				freq-range = <24000000 24000000>;
+				#clock-cells = <0>;
+				clock-output-names = "v2m:oscclk2";
+			};
+
+			volt@0 {
+				/* Logic level voltage */
+				compatible = "arm,vexpress-volt";
+				arm,vexpress-sysreg,func = <2 0>;
+				regulator-name = "VIO";
+				regulator-always-on;
+				label = "VIO";
+			};
+
+			temp@0 {
+				/* MCC internal operating temperature */
+				compatible = "arm,vexpress-temp";
+				arm,vexpress-sysreg,func = <4 0>;
+				label = "MCC";
+			};
+
+			reset@0 {
+				compatible = "arm,vexpress-reset";
+				arm,vexpress-sysreg,func = <5 0>;
+			};
+
+			muxfpga@0 {
+				compatible = "arm,vexpress-muxfpga";
+				arm,vexpress-sysreg,func = <7 0>;
+			};
+
+			shutdown@0 {
+				compatible = "arm,vexpress-shutdown";
+				arm,vexpress-sysreg,func = <8 0>;
+			};
+
+			reboot@0 {
+				compatible = "arm,vexpress-reboot";
+				arm,vexpress-sysreg,func = <9 0>;
+			};
+
+			dvimode@0 {
+				compatible = "arm,vexpress-dvimode";
+				arm,vexpress-sysreg,func = <11 0>;
+			};
+		};
 	};
-};

arch/arm/boot/dts/vexpress-v2m.dtsi

@@ -17,16 +17,15 @@
  * CHANGES TO vexpress-v2m-rs1.dtsi!
  */
 
-/ {
-	aliases {
-		arm,v2m_timer = &v2m_timer01;
-	};
-
 	motherboard {
-		compatible = "simple-bus";
+		model = "V2M-P1";
+		arm,hbi = <0x190>;
+		arm,vexpress,site = <0>;
+		compatible = "arm,vexpress,v2m-p1", "simple-bus";
 		#address-cells = <2>; /* SMB chipselect number and offset */
 		#size-cells = <1>;
 		#interrupt-cells = <1>;
+		ranges;
 
 		flash@0,00000000 {
 			compatible = "arm,vexpress-flash", "cfi-flash";
@@ -71,14 +70,20 @@ iofpga@7,00000000 {
 			#size-cells = <1>;
 			ranges = <0 7 0 0x20000>;
 
-			sysreg@00000 {
+			v2m_sysreg: sysreg@00000 {
 				compatible = "arm,vexpress-sysreg";
 				reg = <0x00000 0x1000>;
+				gpio-controller;
+				#gpio-cells = <2>;
 			};
 
-			sysctl@01000 {
+			v2m_sysctl: sysctl@01000 {
 				compatible = "arm,sp810", "arm,primecell";
 				reg = <0x01000 0x1000>;
+				clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>;
+				clock-names = "refclk", "timclk", "apb_pclk";
+				#clock-cells = <1>;
+				clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
 			};
 
 			/* PCI-E I2C bus */
@@ -99,66 +104,92 @@ aaci@04000 {
 				compatible = "arm,pl041", "arm,primecell";
 				reg = <0x04000 0x1000>;
 				interrupts = <11>;
+				clocks = <&smbclk>;
+				clock-names = "apb_pclk";
 			};
 
 			mmci@05000 {
 				compatible = "arm,pl180", "arm,primecell";
 				reg = <0x05000 0x1000>;
 				interrupts = <9 10>;
+				cd-gpios = <&v2m_sysreg 0 0>;
+				wp-gpios = <&v2m_sysreg 1 0>;
+				max-frequency = <12000000>;
+				vmmc-supply = <&v2m_fixed_3v3>;
+				clocks = <&v2m_clk24mhz>, <&smbclk>;
+				clock-names = "mclk", "apb_pclk";
 			};
 
 			kmi@06000 {
 				compatible = "arm,pl050", "arm,primecell";
 				reg = <0x06000 0x1000>;
 				interrupts = <12>;
+				clocks = <&v2m_clk24mhz>, <&smbclk>;
+				clock-names = "KMIREFCLK", "apb_pclk";
 			};
 
 			kmi@07000 {
 				compatible = "arm,pl050", "arm,primecell";
 				reg = <0x07000 0x1000>;
 				interrupts = <13>;
+				clocks = <&v2m_clk24mhz>, <&smbclk>;
+				clock-names = "KMIREFCLK", "apb_pclk";
 			};
 
 			v2m_serial0: uart@09000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x09000 0x1000>;
 				interrupts = <5>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			v2m_serial1: uart@0a000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x0a000 0x1000>;
 				interrupts = <6>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			v2m_serial2: uart@0b000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x0b000 0x1000>;
 				interrupts = <7>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			v2m_serial3: uart@0c000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x0c000 0x1000>;
 				interrupts = <8>;
+				clocks = <&v2m_oscclk2>, <&smbclk>;
+				clock-names = "uartclk", "apb_pclk";
 			};
 
 			wdt@0f000 {
 				compatible = "arm,sp805", "arm,primecell";
 				reg = <0x0f000 0x1000>;
 				interrupts = <0>;
+				clocks = <&v2m_refclk32khz>, <&smbclk>;
+				clock-names = "wdogclk", "apb_pclk";
 			};
 
 			v2m_timer01: timer@11000 {
 				compatible = "arm,sp804", "arm,primecell";
 				reg = <0x11000 0x1000>;
 				interrupts = <2>;
+				clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
+				clock-names = "timclken1", "timclken2", "apb_pclk";
 			};
 
 			v2m_timer23: timer@12000 {
 				compatible = "arm,sp804", "arm,primecell";
 				reg = <0x12000 0x1000>;
 				interrupts = <3>;
+				clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>;
+				clock-names = "timclken1", "timclken2", "apb_pclk";
 			};
 
 			/* DVI I2C bus */
@@ -184,6 +215,8 @@ rtc@17000 {
 				compatible = "arm,pl031", "arm,primecell";
 				reg = <0x17000 0x1000>;
 				interrupts = <4>;
+				clocks = <&smbclk>;
+				clock-names = "apb_pclk";
 			};
 
 			compact-flash@1a000 {
@@ -197,6 +230,8 @@ clcd@1f000 {
 				compatible = "arm,pl111", "arm,primecell";
 				reg = <0x1f000 0x1000>;
 				interrupts = <14>;
+				clocks = <&v2m_oscclk1>, <&smbclk>;
+				clock-names = "clcdclk", "apb_pclk";
 			};
 		};
 
@@ -207,5 +242,98 @@ v2m_fixed_3v3: fixedregulator@0 {
 			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
+
+		v2m_clk24mhz: clk24mhz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+			clock-output-names = "v2m:clk24mhz";
+		};
+
+		v2m_refclk1mhz: refclk1mhz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1000000>;
+			clock-output-names = "v2m:refclk1mhz";
+		};
+
+		v2m_refclk32khz: refclk32khz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "v2m:refclk32khz";
+		};
+
+		mcc {
+			compatible = "arm,vexpress,config-bus";
+			arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+			osc@0 {
+				/* MCC static memory clock */
+				compatible = "arm,vexpress-osc";
+				arm,vexpress-sysreg,func = <1 0>;
+				freq-range = <25000000 60000000>;
+				#clock-cells = <0>;
+				clock-output-names = "v2m:oscclk0";
+			};
+
+			v2m_oscclk1: osc@1 {
+				/* CLCD clock */
+				compatible = "arm,vexpress-osc";
+				arm,vexpress-sysreg,func = <1 1>;
+				freq-range = <23750000 63500000>;
+				#clock-cells = <0>;
+				clock-output-names = "v2m:oscclk1";
+			};
+
+			v2m_oscclk2: osc@2 {
+				/* IO FPGA peripheral clock */
+				compatible = "arm,vexpress-osc";
+				arm,vexpress-sysreg,func = <1 2>;
+				freq-range = <24000000 24000000>;
+				#clock-cells = <0>;
+				clock-output-names = "v2m:oscclk2";
+			};
+
+			volt@0 {
+				/* Logic level voltage */
+				compatible = "arm,vexpress-volt";
+				arm,vexpress-sysreg,func = <2 0>;
+				regulator-name = "VIO";
+				regulator-always-on;
+				label = "VIO";
+			};
+
+			temp@0 {
+				/* MCC internal operating temperature */
+				compatible = "arm,vexpress-temp";
+				arm,vexpress-sysreg,func = <4 0>;
+				label = "MCC";
+			};
+
+			reset@0 {
+				compatible = "arm,vexpress-reset";
+				arm,vexpress-sysreg,func = <5 0>;
+			};
+
+			muxfpga@0 {
+				compatible = "arm,vexpress-muxfpga";
+				arm,vexpress-sysreg,func = <7 0>;
+			};
+
+			shutdown@0 {
+				compatible = "arm,vexpress-shutdown";
+				arm,vexpress-sysreg,func = <8 0>;
+			};
+
+			reboot@0 {
+				compatible = "arm,vexpress-reboot";
+				arm,vexpress-sysreg,func = <9 0>;
+			};
+
+			dvimode@0 {
+				compatible = "arm,vexpress-dvimode";
+				arm,vexpress-sysreg,func = <11 0>;
+			};
+		};
 	};
-};

arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts

@@ -12,6 +12,7 @@
 / {
 	model = "V2P-CA15";
 	arm,hbi = <0x237>;
+	arm,vexpress,site = <0xf>;
 	compatible = "arm,vexpress,v2p-ca15,tc1", "arm,vexpress,v2p-ca15", "arm,vexpress";
 	interrupt-parent = <&gic>;
 	#address-cells = <2>;
@@ -54,17 +55,24 @@ hdlcd@2b000000 {
 		compatible = "arm,hdlcd";
 		reg = <0 0x2b000000 0 0x1000>;
 		interrupts = <0 85 4>;
+		clocks = <&oscclk5>;
+		clock-names = "pxlclk";
 	};
 
 	memory-controller@2b0a0000 {
 		compatible = "arm,pl341", "arm,primecell";
 		reg = <0 0x2b0a0000 0 0x1000>;
+		clocks = <&oscclk7>;
+		clock-names = "apb_pclk";
 	};
 
 	wdt@2b060000 {
 		compatible = "arm,sp805", "arm,primecell";
+		status = "disabled";
 		reg = <0 0x2b060000 0 0x1000>;
 		interrupts = <98>;
+		clocks = <&oscclk7>;
+		clock-names = "apb_pclk";
 	};
 
 	gic: interrupt-controller@2c001000 {
@@ -84,6 +92,8 @@ memory-controller@7ffd0000 {
 		reg = <0 0x7ffd0000 0 0x1000>;
 		interrupts = <0 86 4>,
 			     <0 87 4>;
+		clocks = <&oscclk7>;
+		clock-names = "apb_pclk";
 	};
 
 	dma@7ffb0000 {
@@ -94,6 +104,8 @@ dma@7ffb0000 {
 			     <0 89 4>,
 			     <0 90 4>,
 			     <0 91 4>;
+		clocks = <&oscclk7>;
+		clock-names = "apb_pclk";
 	};
 
 	timer {
@@ -110,7 +122,109 @@ pmu {
 			     <0 69 4>;
 	};
 
-	motherboard {
+	dcc {
+		compatible = "arm,vexpress,config-bus";
+		arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+		osc@0 {
+			/* CPU PLL reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 0>;
+			freq-range = <50000000 60000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk0";
+		};
+
+		osc@4 {
+			/* Multiplexed AXI master clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 4>;
+			freq-range = <20000000 40000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk4";
+		};
+
+		oscclk5: osc@5 {
+			/* HDLCD PLL reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 5>;
+			freq-range = <23750000 165000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk5";
+		};
+
+		smbclk: osc@6 {
+			/* SMB clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 6>;
+			freq-range = <20000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk6";
+		};
+
+		oscclk7: osc@7 {
+			/* SYS PLL reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 7>;
+			freq-range = <20000000 60000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk7";
+		};
+
+		osc@8 {
+			/* DDR2 PLL reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 8>;
+			freq-range = <40000000 40000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk8";
+		};
+
+		volt@0 {
+			/* CPU core voltage */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 0>;
+			regulator-name = "Cores";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+			label = "Cores";
+		};
+
+		amp@0 {
+			/* Total current for the two cores */
+			compatible = "arm,vexpress-amp";
+			arm,vexpress-sysreg,func = <3 0>;
+			label = "Cores";
+		};
+
+		temp@0 {
+			/* DCC internal temperature */
+			compatible = "arm,vexpress-temp";
+			arm,vexpress-sysreg,func = <4 0>;
+			label = "DCC";
+		};
+
+		power@0 {
+			/* Total power */
+			compatible = "arm,vexpress-power";
+			arm,vexpress-sysreg,func = <12 0>;
+			label = "Cores";
+		};
+
+		energy@0 {
+			/* Total energy */
+			compatible = "arm,vexpress-energy";
+			arm,vexpress-sysreg,func = <13 0>;
+			label = "Cores";
+		};
+	};
+
+	smb {
+		compatible = "simple-bus";
+
+		#address-cells = <2>;
+		#size-cells = <1>;
 		ranges = <0 0 0 0x08000000 0x04000000>,
 			 <1 0 0 0x14000000 0x04000000>,
 			 <2 0 0 0x18000000 0x04000000>,
@@ -118,6 +232,7 @@ motherboard {
 			 <4 0 0 0x0c000000 0x04000000>,
 			 <5 0 0 0x10000000 0x04000000>;
 
+		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 63>;
 		interrupt-map = <0 0  0 &gic 0  0 4>,
 				<0 0  1 &gic 0  1 4>,
@@ -162,7 +277,7 @@ motherboard {
 				<0 0 40 &gic 0 40 4>,
 				<0 0 41 &gic 0 41 4>,
 				<0 0 42 &gic 0 42 4>;
+
+		/include/ "vexpress-v2m-rs1.dtsi"
 	};
 };
-
-/include/ "vexpress-v2m-rs1.dtsi"

arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts

@@ -12,6 +12,7 @@
 / {
 	model = "V2P-CA15_CA7";
 	arm,hbi = <0x249>;
+	arm,vexpress,site = <0xf>;
 	compatible = "arm,vexpress,v2p-ca15_a7", "arm,vexpress";
 	interrupt-parent = <&gic>;
 	#address-cells = <2>;
@@ -74,17 +75,23 @@ wdt@2a490000 {
 		compatible = "arm,sp805", "arm,primecell";
 		reg = <0 0x2a490000 0 0x1000>;
 		interrupts = <98>;
+		clocks = <&oscclk6a>, <&oscclk6a>;
+		clock-names = "wdogclk", "apb_pclk";
 	};
 
 	hdlcd@2b000000 {
 		compatible = "arm,hdlcd";
 		reg = <0 0x2b000000 0 0x1000>;
 		interrupts = <0 85 4>;
+		clocks = <&oscclk5>;
+		clock-names = "pxlclk";
 	};
 
 	memory-controller@2b0a0000 {
 		compatible = "arm,pl341", "arm,primecell";
 		reg = <0 0x2b0a0000 0 0x1000>;
+		clocks = <&oscclk6a>;
+		clock-names = "apb_pclk";
 	};
 
 	gic: interrupt-controller@2c001000 {
@@ -104,6 +111,8 @@ memory-controller@7ffd0000 {
 		reg = <0 0x7ffd0000 0 0x1000>;
 		interrupts = <0 86 4>,
 			     <0 87 4>;
+		clocks = <&oscclk6a>;
+		clock-names = "apb_pclk";
 	};
 
 	dma@7ff00000 {
@@ -114,6 +123,8 @@ dma@7ff00000 {
 			     <0 89 4>,
 			     <0 90 4>,
 			     <0 91 4>;
+		clocks = <&oscclk6a>;
+		clock-names = "apb_pclk";
 	};
 
 	timer {
@@ -130,7 +141,175 @@ pmu {
 			     <0 69 4>;
 	};
 
-	motherboard {
+	oscclk6a: oscclk6a {
+		/* Reference 24MHz clock */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "oscclk6a";
+	};
+
+	dcc {
+		compatible = "arm,vexpress,config-bus";
+		arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+		osc@0 {
+			/* A15 PLL 0 reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 0>;
+			freq-range = <17000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk0";
+		};
+
+		osc@1 {
+			/* A15 PLL 1 reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 1>;
+			freq-range = <17000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk1";
+		};
+
+		osc@2 {
+			/* A7 PLL 0 reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 2>;
+			freq-range = <17000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk2";
+		};
+
+		osc@3 {
+			/* A7 PLL 1 reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 3>;
+			freq-range = <17000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk3";
+		};
+
+		osc@4 {
+			/* External AXI master clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 4>;
+			freq-range = <20000000 40000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk4";
+		};
+
+		oscclk5: osc@5 {
+			/* HDLCD PLL reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 5>;
+			freq-range = <23750000 165000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk5";
+		};
+
+		smbclk: osc@6 {
+			/* Static memory controller clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 6>;
+			freq-range = <20000000 40000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk6";
+		};
+
+		osc@7 {
+			/* SYS PLL reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 7>;
+			freq-range = <17000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk7";
+		};
+
+		osc@8 {
+			/* DDR2 PLL reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 8>;
+			freq-range = <20000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk8";
+		};
+
+		volt@0 {
+			/* A15 CPU core voltage */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 0>;
+			regulator-name = "A15 Vcore";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+			label = "A15 Vcore";
+		};
+
+		volt@1 {
+			/* A7 CPU core voltage */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 1>;
+			regulator-name = "A7 Vcore";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+			label = "A7 Vcore";
+		};
+
+		amp@0 {
+			/* Total current for the two A15 cores */
+			compatible = "arm,vexpress-amp";
+			arm,vexpress-sysreg,func = <3 0>;
+			label = "A15 Icore";
+		};
+
+		amp@1 {
+			/* Total current for the three A7 cores */
+			compatible = "arm,vexpress-amp";
+			arm,vexpress-sysreg,func = <3 1>;
+			label = "A7 Icore";
+		};
+
+		temp@0 {
+			/* DCC internal temperature */
+			compatible = "arm,vexpress-temp";
+			arm,vexpress-sysreg,func = <4 0>;
+			label = "DCC";
+		};
+
+		power@0 {
+			/* Total power for the two A15 cores */
+			compatible = "arm,vexpress-power";
+			arm,vexpress-sysreg,func = <12 0>;
+			label = "A15 Pcore";
+		};
+		power@1 {
+			/* Total power for the three A7 cores */
+			compatible = "arm,vexpress-power";
+			arm,vexpress-sysreg,func = <12 1>;
+			label = "A7 Pcore";
+		};
+
+		energy@0 {
+			/* Total energy for the two A15 cores */
+			compatible = "arm,vexpress-energy";
+			arm,vexpress-sysreg,func = <13 0>;
+			label = "A15 Jcore";
+		};
+
+		energy@2 {
+			/* Total energy for the three A7 cores */
+			compatible = "arm,vexpress-energy";
+			arm,vexpress-sysreg,func = <13 2>;
+			label = "A7 Jcore";
+		};
+	};
+
+	smb {
+		compatible = "simple-bus";
+
+		#address-cells = <2>;
+		#size-cells = <1>;
 		ranges = <0 0 0 0x08000000 0x04000000>,
 			 <1 0 0 0x14000000 0x04000000>,
 			 <2 0 0 0x18000000 0x04000000>,
@@ -138,6 +317,7 @@ motherboard {
 			 <4 0 0 0x0c000000 0x04000000>,
 			 <5 0 0 0x10000000 0x04000000>;
 
+		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 63>;
 		interrupt-map = <0 0  0 &gic 0  0 4>,
 				<0 0  1 &gic 0  1 4>,
@@ -182,7 +362,7 @@ motherboard {
 				<0 0 40 &gic 0 40 4>,
 				<0 0 41 &gic 0 41 4>,
 				<0 0 42 &gic 0 42 4>;
+
+		/include/ "vexpress-v2m-rs1.dtsi"
 	};
 };
-
-/include/ "vexpress-v2m-rs1.dtsi"

arch/arm/boot/dts/vexpress-v2p-ca5s.dts

@@ -12,6 +12,7 @@
 / {
 	model = "V2P-CA5s";
 	arm,hbi = <0x225>;
+	arm,vexpress,site = <0xf>;
 	compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress";
 	interrupt-parent = <&gic>;
 	#address-cells = <1>;
@@ -56,11 +57,15 @@ hdlcd@2a110000 {
 		compatible = "arm,hdlcd";
 		reg = <0x2a110000 0x1000>;
 		interrupts = <0 85 4>;
+		clocks = <&oscclk3>;
+		clock-names = "pxlclk";
 	};
 
 	memory-controller@2a150000 {
 		compatible = "arm,pl341", "arm,primecell";
 		reg = <0x2a150000 0x1000>;
+		clocks = <&oscclk1>;
+		clock-names = "apb_pclk";
 	};
 
 	memory-controller@2a190000 {
@@ -68,6 +73,8 @@ memory-controller@2a190000 {
 		reg = <0x2a190000 0x1000>;
 		interrupts = <0 86 4>,
 			     <0 87 4>;
+		clocks = <&oscclk1>;
+		clock-names = "apb_pclk";
 	};
 
 	scu@2c000000 {
@@ -109,7 +116,77 @@ pmu {
 			     <0 69 4>;
 	};
 
-	motherboard {
+	dcc {
+		compatible = "arm,vexpress,config-bus";
+		arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+		osc@0 {
+			/* CPU and internal AXI reference clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 0>;
+			freq-range = <50000000 100000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk0";
+		};
+
+		oscclk1: osc@1 {
+			/* Multiplexed AXI master clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 1>;
+			freq-range = <5000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk1";
+		};
+
+		osc@2 {
+			/* DDR2 */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 2>;
+			freq-range = <80000000 120000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk2";
+		};
+
+		oscclk3: osc@3 {
+			/* HDLCD */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 3>;
+			freq-range = <23750000 165000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk3";
+		};
+
+		osc@4 {
+			/* Test chip gate configuration */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 4>;
+			freq-range = <80000000 80000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk4";
+		};
+
+		smbclk: osc@5 {
+			/* SMB clock */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 5>;
+			freq-range = <25000000 60000000>;
+			#clock-cells = <0>;
+			clock-output-names = "oscclk5";
+		};
+
+		temp@0 {
+			/* DCC internal operating temperature */
+			compatible = "arm,vexpress-temp";
+			arm,vexpress-sysreg,func = <4 0>;
+			label = "DCC";
+		};
+	};
+
+	smb {
+		compatible = "simple-bus";
+
+		#address-cells = <2>;
+		#size-cells = <1>;
 		ranges = <0 0 0x08000000 0x04000000>,
 			 <1 0 0x14000000 0x04000000>,
 			 <2 0 0x18000000 0x04000000>,
@@ -117,6 +194,7 @@ motherboard {
 			 <4 0 0x0c000000 0x04000000>,
 			 <5 0 0x10000000 0x04000000>;
 
+		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 63>;
 		interrupt-map = <0 0  0 &gic 0  0 4>,
 				<0 0  1 &gic 0  1 4>,
@@ -161,7 +239,7 @@ motherboard {
 				<0 0 40 &gic 0 40 4>,
 				<0 0 41 &gic 0 41 4>,
 				<0 0 42 &gic 0 42 4>;
+
+		/include/ "vexpress-v2m-rs1.dtsi"
 	};
 };
-
-/include/ "vexpress-v2m-rs1.dtsi"

arch/arm/boot/dts/vexpress-v2p-ca9.dts

@@ -12,6 +12,7 @@
 / {
 	model = "V2P-CA9";
 	arm,hbi = <0x191>;
+	arm,vexpress,site = <0xf>;
 	compatible = "arm,vexpress,v2p-ca9", "arm,vexpress";
 	interrupt-parent = <&gic>;
 	#address-cells = <1>;
@@ -70,11 +71,15 @@ clcd@10020000 {
 		compatible = "arm,pl111", "arm,primecell";
 		reg = <0x10020000 0x1000>;
 		interrupts = <0 44 4>;
+		clocks = <&oscclk1>, <&oscclk2>;
+		clock-names = "clcdclk", "apb_pclk";
 	};
 
 	memory-controller@100e0000 {
 		compatible = "arm,pl341", "arm,primecell";
 		reg = <0x100e0000 0x1000>;
+		clocks = <&oscclk2>;
+		clock-names = "apb_pclk";
 	};
 
 	memory-controller@100e1000 {
@@ -82,6 +87,8 @@ memory-controller@100e1000 {
 		reg = <0x100e1000 0x1000>;
 		interrupts = <0 45 4>,
 			     <0 46 4>;
+		clocks = <&oscclk2>;
+		clock-names = "apb_pclk";
 	};
 
 	timer@100e4000 {
@@ -89,12 +96,16 @@ timer@100e4000 {
 		reg = <0x100e4000 0x1000>;
 		interrupts = <0 48 4>,
 			     <0 49 4>;
+		clocks = <&oscclk2>, <&oscclk2>;
+		clock-names = "timclk", "apb_pclk";
 	};
 
 	watchdog@100e5000 {
 		compatible = "arm,sp805", "arm,primecell";
 		reg = <0x100e5000 0x1000>;
 		interrupts = <0 51 4>;
+		clocks = <&oscclk2>, <&oscclk2>;
+		clock-names = "wdogclk", "apb_pclk";
 	};
 
 	scu@1e000000 {
@@ -140,13 +151,132 @@ pmu {
 			     <0 63 4>;
 	};
 
-	motherboard {
+	dcc {
+		compatible = "arm,vexpress,config-bus";
+		arm,vexpress,config-bridge = <&v2m_sysreg>;
+
+		osc@0 {
+			/* ACLK clock to the AXI master port on the test chip */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 0>;
+			freq-range = <30000000 50000000>;
+			#clock-cells = <0>;
+			clock-output-names = "extsaxiclk";
+		};
+
+		oscclk1: osc@1 {
+			/* Reference clock for the CLCD */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 1>;
+			freq-range = <10000000 80000000>;
+			#clock-cells = <0>;
+			clock-output-names = "clcdclk";
+		};
+
+		smbclk: oscclk2: osc@2 {
+			/* Reference clock for the test chip internal PLLs */
+			compatible = "arm,vexpress-osc";
+			arm,vexpress-sysreg,func = <1 2>;
+			freq-range = <33000000 100000000>;
+			#clock-cells = <0>;
+			clock-output-names = "tcrefclk";
+		};
+
+		volt@0 {
+			/* Test Chip internal logic voltage */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 0>;
+			regulator-name = "VD10";
+			regulator-always-on;
+			label = "VD10";
+		};
+
+		volt@1 {
+			/* PL310, L2 cache, RAM cell supply (not PL310 logic) */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 1>;
+			regulator-name = "VD10_S2";
+			regulator-always-on;
+			label = "VD10_S2";
+		};
+
+		volt@2 {
+			/* Cortex-A9 system supply, Cores, MPEs, SCU and PL310 logic */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 2>;
+			regulator-name = "VD10_S3";
+			regulator-always-on;
+			label = "VD10_S3";
+		};
+
+		volt@3 {
+			/* DDR2 SDRAM and Test Chip DDR2 I/O supply */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 3>;
+			regulator-name = "VCC1V8";
+			regulator-always-on;
+			label = "VCC1V8";
+		};
+
+		volt@4 {
+			/* DDR2 SDRAM VTT termination voltage */
+			compatible = "arm,vexpress-volt";
+			arm,vexpress-sysreg,func = <2 4>;
+			regulator-name = "DDR2VTT";
+			regulator-always-on;
+			label = "DDR2VTT";
+		};
+
+		volt@5 {
+			/* Local board supply for miscellaneous logic external to the Test Chip */
+			arm,vexpress-sysreg,func = <2 5>;
+			compatible = "arm,vexpress-volt";
+			regulator-name = "VCC3V3";
+			regulator-always-on;
+			label = "VCC3V3";
+		};
+
+		amp@0 {
+			/* PL310, L2 cache, RAM cell supply (not PL310 logic) */
+			compatible = "arm,vexpress-amp";
+			arm,vexpress-sysreg,func = <3 0>;
+			label = "VD10_S2";
+		};
+
+		amp@1 {
+			/* Cortex-A9 system supply, Cores, MPEs, SCU and PL310 logic */
+			compatible = "arm,vexpress-amp";
+			arm,vexpress-sysreg,func = <3 1>;
+			label = "VD10_S3";
+		};
+
+		power@0 {
+			/* PL310, L2 cache, RAM cell supply (not PL310 logic) */
+			compatible = "arm,vexpress-power";
+			arm,vexpress-sysreg,func = <12 0>;
+			label = "PVD10_S2";
+		};
+
+		power@1 {
+			/* Cortex-A9 system supply, Cores, MPEs, SCU and PL310 logic */
+			compatible = "arm,vexpress-power";
+			arm,vexpress-sysreg,func = <12 1>;
+			label = "PVD10_S3";
+		};
+	};
+
+	smb {
+		compatible = "simple-bus";
+
+		#address-cells = <2>;
+		#size-cells = <1>;
 		ranges = <0 0 0x40000000 0x04000000>,
 			 <1 0 0x44000000 0x04000000>,
 			 <2 0 0x48000000 0x04000000>,
 			 <3 0 0x4c000000 0x04000000>,
 			 <7 0 0x10000000 0x00020000>;
 
+		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 63>;
 		interrupt-map = <0 0  0 &gic 0  0 4>,
 				<0 0  1 &gic 0  1 4>,
@@ -191,7 +321,7 @@ motherboard {
 				<0 0 40 &gic 0 40 4>,
 				<0 0 41 &gic 0 41 4>,
 				<0 0 42 &gic 0 42 4>;
+
+		/include/ "vexpress-v2m.dtsi"
 	};
 };
-
-/include/ "vexpress-v2m.dtsi"

arch/arm/include/asm/hardware/sp810.h

@@ -50,12 +50,6 @@
 #define SCPCELLID2		0xFF8
 #define SCPCELLID3		0xFFC
 
-#define SCCTRL_TIMEREN0SEL_REFCLK	(0 << 15)
-#define SCCTRL_TIMEREN0SEL_TIMCLK	(1 << 15)
-
-#define SCCTRL_TIMEREN1SEL_REFCLK	(0 << 17)
-#define SCCTRL_TIMEREN1SEL_TIMCLK	(1 << 17)
-
 #define SCCTRL_TIMERENnSEL_SHIFT(n)	(15 + ((n) * 2))
 
 static inline void sysctl_soft_reset(void __iomem *base)

arch/arm/mach-vexpress/Kconfig

 config ARCH_VEXPRESS
 	bool "ARM Ltd. Versatile Express family" if ARCH_MULTI_V7
-	select ARCH_WANT_OPTIONAL_GPIOLIB
+	select ARCH_REQUIRE_GPIOLIB
 	select ARM_AMBA
 	select ARM_GIC
 	select ARM_TIMER_SP804
 	select CLKDEV_LOOKUP
 	select COMMON_CLK
+	select COMMON_CLK_VERSATILE
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select HAVE_CLK
@@ -17,6 +18,7 @@ config ARCH_VEXPRESS
 	select PLAT_VERSATILE
 	select PLAT_VERSATILE_CLCD
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
+	select VEXPRESS_CONFIG
 	help
 	  This option enables support for systems using Cortex processor based
 	  ARM core and logic (FPGA) tiles on the Versatile Express motherboard,

arch/arm/mach-vexpress/Makefile

@@ -4,7 +4,7 @@
 ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \
 	-I$(srctree)/arch/arm/plat-versatile/include
 
-obj-y					:= v2m.o
+obj-y					:= v2m.o reset.o
 obj-$(CONFIG_ARCH_VEXPRESS_CA9X4)	+= ct-ca9x4.o
 obj-$(CONFIG_SMP)			+= platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o

arch/arm/mach-vexpress/ct-ca9x4.c

@@ -9,6 +9,7 @@
 #include <linux/amba/bus.h>
 #include <linux/amba/clcd.h>
 #include <linux/clkdev.h>
+#include <linux/vexpress.h>
 
 #include <asm/hardware/arm_timer.h>
 #include <asm/hardware/cache-l2x0.h>
@@ -64,19 +65,6 @@ static void __init ct_ca9x4_init_irq(void)
 	ca9x4_twd_init();
 }
 
-static void ct_ca9x4_clcd_enable(struct clcd_fb *fb)
-{
-	u32 site = v2m_get_master_site();
-
-	/*
-	 * Old firmware was using the "site" component of the command
-	 * to control the DVI muxer (while it should be always 0 ie. MB).
-	 * Newer firmware uses the data register. Keep both for compatibility.
-	 */
-	v2m_cfg_write(SYS_CFG_MUXFPGA | SYS_CFG_SITE(site), site);
-	v2m_cfg_write(SYS_CFG_DVIMODE | SYS_CFG_SITE(SYS_CFG_SITE_MB), 2);
-}
-
 static int ct_ca9x4_clcd_setup(struct clcd_fb *fb)
 {
 	unsigned long framesize = 1024 * 768 * 2;
@@ -93,7 +81,6 @@ static struct clcd_board ct_ca9x4_clcd_data = {
 	.caps		= CLCD_CAP_5551 | CLCD_CAP_565,
 	.check		= clcdfb_check,
 	.decode		= clcdfb_decode,
-	.enable		= ct_ca9x4_clcd_enable,
 	.setup		= ct_ca9x4_clcd_setup,
 	.mmap		= versatile_clcd_mmap_dma,
 	.remove		= versatile_clcd_remove_dma,
@@ -111,14 +98,6 @@ static struct amba_device *ct_ca9x4_amba_devs[] __initdata = {
 	&gpio_device,
 };
 
-
-static struct v2m_osc ct_osc1 = {
-	.osc = 1,
-	.rate_min = 10000000,
-	.rate_max = 80000000,
-	.rate_default = 23750000,
-};
-
 static struct resource pmu_resources[] = {
 	[0] = {
 		.start	= IRQ_CT_CA9X4_PMU_CPU0,
@@ -149,10 +128,18 @@ static struct platform_device pmu_device = {
 	.resource	= pmu_resources,
 };
 
+static struct platform_device osc1_device = {
+	.name		= "vexpress-osc",
+	.id		= 1,
+	.num_resources	= 1,
+	.resource	= (struct resource []) {
+		VEXPRESS_RES_FUNC(0xf, 1),
+	},
+};
+
 static void __init ct_ca9x4_init(void)
 {
 	int i;
-	struct clk *clk;
 
 #ifdef CONFIG_CACHE_L2X0
 	void __iomem *l2x0_base = ioremap(CT_CA9X4_L2CC, SZ_4K);
@@ -164,14 +151,14 @@ static void __init ct_ca9x4_init(void)
 	l2x0_init(l2x0_base, 0x00400000, 0xfe0fffff);
 #endif
 
-	ct_osc1.site = v2m_get_master_site();
-	clk = v2m_osc_register("ct:osc1", &ct_osc1);
-	clk_register_clkdev(clk, NULL, "ct:clcd");
-
 	for (i = 0; i < ARRAY_SIZE(ct_ca9x4_amba_devs); i++)
 		amba_device_register(ct_ca9x4_amba_devs[i], &iomem_resource);
 
 	platform_device_register(&pmu_device);
+	platform_device_register(&osc1_device);
+
+	WARN_ON(clk_register_clkdev(vexpress_osc_setup(&osc1_device.dev),
+			NULL, "ct:clcd"));
 }
 
 #ifdef CONFIG_SMP

arch/arm/mach-vexpress/include/mach/motherboard.h

 #ifndef __MACH_MOTHERBOARD_H
 #define __MACH_MOTHERBOARD_H
 
-#include <linux/clk-provider.h>
-
 /*
  * Physical addresses, offset from V2M_PA_CS0-3
  */
@@ -41,31 +39,6 @@
 #define V2M_CF			(V2M_PA_CS7 + 0x0001a000)
 #define V2M_CLCD		(V2M_PA_CS7 + 0x0001f000)
 
-/*
- * Offsets from SYSREGS base
- */
-#define V2M_SYS_ID		0x000
-#define V2M_SYS_SW		0x004
-#define V2M_SYS_LED		0x008
-#define V2M_SYS_100HZ		0x024
-#define V2M_SYS_FLAGS		0x030
-#define V2M_SYS_FLAGSSET	0x030
-#define V2M_SYS_FLAGSCLR	0x034
-#define V2M_SYS_NVFLAGS		0x038
-#define V2M_SYS_NVFLAGSSET	0x038
-#define V2M_SYS_NVFLAGSCLR	0x03c
-#define V2M_SYS_MCI		0x048
-#define V2M_SYS_FLASH		0x03c
-#define V2M_SYS_CFGSW		0x058
-#define V2M_SYS_24MHZ		0x05c
-#define V2M_SYS_MISC		0x060
-#define V2M_SYS_DMA		0x064
-#define V2M_SYS_PROCID0		0x084
-#define V2M_SYS_PROCID1		0x088
-#define V2M_SYS_CFGDATA		0x0a0
-#define V2M_SYS_CFGCTRL		0x0a4
-#define V2M_SYS_CFGSTAT		0x0a8
-
 
 /*
  * Interrupts.  Those in {} are for AMBA devices
@@ -90,43 +63,6 @@
 #define IRQ_V2M_PCIE		(32 + 17)
 
 
-/*
- * Configuration
- */
-#define SYS_CFG_START		(1 << 31)
-#define SYS_CFG_WRITE		(1 << 30)
-#define SYS_CFG_OSC		(1 << 20)
-#define SYS_CFG_VOLT		(2 << 20)
-#define SYS_CFG_AMP		(3 << 20)
-#define SYS_CFG_TEMP		(4 << 20)
-#define SYS_CFG_RESET		(5 << 20)
-#define SYS_CFG_SCC		(6 << 20)
-#define SYS_CFG_MUXFPGA		(7 << 20)
-#define SYS_CFG_SHUTDOWN	(8 << 20)
-#define SYS_CFG_REBOOT		(9 << 20)
-#define SYS_CFG_DVIMODE		(11 << 20)
-#define SYS_CFG_POWER		(12 << 20)
-#define SYS_CFG_SITE(n)		((n) << 16)
-#define SYS_CFG_SITE_MB		0
-#define SYS_CFG_SITE_DB1	1
-#define SYS_CFG_SITE_DB2	2
-#define SYS_CFG_STACK(n)	((n) << 12)
-
-#define SYS_CFG_ERR		(1 << 1)
-#define SYS_CFG_COMPLETE	(1 << 0)
-
-int v2m_cfg_write(u32 devfn, u32 data);
-int v2m_cfg_read(u32 devfn, u32 *data);
-void v2m_flags_set(u32 data);
-
-/*
- * Miscellaneous
- */
-#define SYS_MISC_MASTERSITE	(1 << 14)
-#define SYS_PROCIDx_HBI_MASK	0xfff
-
-int v2m_get_master_site(void);
-
 /*
  * Core tile IDs
  */
@@ -149,21 +85,4 @@ struct ct_desc {
 
 extern struct ct_desc *ct_desc;
 
-/*
- * OSC clock provider
- */
-struct v2m_osc {
-	struct clk_hw hw;
-	u8 site; /* 0 = motherboard, 1 = site 1, 2 = site 2 */
-	u8 stack; /* board stack position */
-	u16 osc;
-	unsigned long rate_min;
-	unsigned long rate_max;
-	unsigned long rate_default;
-};
-
-#define to_v2m_osc(osc) container_of(osc, struct v2m_osc, hw)
-
-struct clk *v2m_osc_register(const char *name, struct v2m_osc *osc);
-
 #endif

arch/arm/mach-vexpress/platsmp.c

@@ -13,6 +13,7 @@
 #include <linux/smp.h>
 #include <linux/io.h>
 #include <linux/of_fdt.h>
+#include <linux/vexpress.h>
 
 #include <asm/smp_scu.h>
 #include <asm/hardware/gic.h>
@@ -193,7 +194,7 @@ static void __init vexpress_smp_prepare_cpus(unsigned int max_cpus)
 	 * until it receives a soft interrupt, and then the
 	 * secondary CPU branches to this address.
 	 */
-	v2m_flags_set(virt_to_phys(versatile_secondary_startup));
+	vexpress_flags_set(virt_to_phys(versatile_secondary_startup));
 }
 
 struct smp_operations __initdata vexpress_smp_ops = {

drivers/mfd/Kconfig

@@ -1070,3 +1070,9 @@ config MCP_UCB1200_TS
 	depends on MCP_UCB1200 && INPUT
 
 endmenu
+
+config VEXPRESS_CONFIG
+	bool
+	help
+	  Platform configuration infrastructure for the ARM Ltd.
+	  Versatile Express.

drivers/mfd/Makefile

@@ -138,3 +138,4 @@ obj-$(CONFIG_MFD_RC5T583)	+= rc5t583.o rc5t583-irq.o
 obj-$(CONFIG_MFD_SEC_CORE)	+= sec-core.o sec-irq.o
 obj-$(CONFIG_MFD_SYSCON)	+= syscon.o
 obj-$(CONFIG_MFD_LM3533)	+= lm3533-core.o lm3533-ctrlbank.o
+obj-$(CONFIG_VEXPRESS_CONFIG)	+= vexpress-config.o vexpress-sysreg.o

drivers/mfd/vexpress-config.c

+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2012 ARM Limited
+ */
+
+#define pr_fmt(fmt) "vexpress-config: " fmt
+
+#include <linux/bitops.h>
+#include <linux/completion.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/vexpress.h>
+
+
+#define VEXPRESS_CONFIG_MAX_BRIDGES 2
+
+struct vexpress_config_bridge {
+	struct device_node *node;
+	struct vexpress_config_bridge_info *info;
+	struct list_head transactions;
+	spinlock_t transactions_lock;
+} vexpress_config_bridges[VEXPRESS_CONFIG_MAX_BRIDGES];
+
+static DECLARE_BITMAP(vexpress_config_bridges_map,
+		ARRAY_SIZE(vexpress_config_bridges));
+static DEFINE_MUTEX(vexpress_config_bridges_mutex);
+
+struct vexpress_config_bridge *vexpress_config_bridge_register(
+		struct device_node *node,
+		struct vexpress_config_bridge_info *info)
+{
+	struct vexpress_config_bridge *bridge;
+	int i;
+
+	pr_debug("Registering bridge '%s'\n", info->name);
+
+	mutex_lock(&vexpress_config_bridges_mutex);
+	i = find_first_zero_bit(vexpress_config_bridges_map,
+			ARRAY_SIZE(vexpress_config_bridges));
+	if (i >= ARRAY_SIZE(vexpress_config_bridges)) {
+		pr_err("Can't register more bridges!\n");
+		mutex_unlock(&vexpress_config_bridges_mutex);
+		return NULL;
+	}
+	__set_bit(i, vexpress_config_bridges_map);
+	bridge = &vexpress_config_bridges[i];
+
+	bridge->node = node;
+	bridge->info = info;
+	INIT_LIST_HEAD(&bridge->transactions);
+	spin_lock_init(&bridge->transactions_lock);
+
+	mutex_unlock(&vexpress_config_bridges_mutex);
+
+	return bridge;
+}
+
+void vexpress_config_bridge_unregister(struct vexpress_config_bridge *bridge)
+{
+	struct vexpress_config_bridge __bridge = *bridge;
+	int i;
+
+	mutex_lock(&vexpress_config_bridges_mutex);
+	for (i = 0; i < ARRAY_SIZE(vexpress_config_bridges); i++)
+		if (&vexpress_config_bridges[i] == bridge)
+			__clear_bit(i, vexpress_config_bridges_map);
+	mutex_unlock(&vexpress_config_bridges_mutex);
+
+	WARN_ON(!list_empty(&__bridge.transactions));
+	while (!list_empty(&__bridge.transactions))
+		cpu_relax();
+}
+
+
+struct vexpress_config_func {
+	struct vexpress_config_bridge *bridge;
+	void *func;
+};
+
+struct vexpress_config_func *__vexpress_config_func_get(struct device *dev,
+		struct device_node *node)
+{
+	struct device_node *bridge_node;
+	struct vexpress_config_func *func;
+	int i;
+
+	if (WARN_ON(dev && node && dev->of_node != node))
+		return NULL;
+	if (dev && !node)
+		node = dev->of_node;
+
+	func = kzalloc(sizeof(*func), GFP_KERNEL);
+	if (!func)
+		return NULL;
+
+	bridge_node = of_node_get(node);
+	while (bridge_node) {
+		const __be32 *prop = of_get_property(bridge_node,
+				"arm,vexpress,config-bridge", NULL);
+
+		if (prop) {
+			bridge_node = of_find_node_by_phandle(
+					be32_to_cpup(prop));
+			break;
+		}
+
+		bridge_node = of_get_next_parent(bridge_node);
+	}
+
+	mutex_lock(&vexpress_config_bridges_mutex);
+	for (i = 0; i < ARRAY_SIZE(vexpress_config_bridges); i++) {
+		struct vexpress_config_bridge *bridge =
+				&vexpress_config_bridges[i];
+
+		if (test_bit(i, vexpress_config_bridges_map) &&
+				bridge->node == bridge_node) {
+			func->bridge = bridge;
+			func->func = bridge->info->func_get(dev, node);
+			break;
+		}
+	}
+	mutex_unlock(&vexpress_config_bridges_mutex);
+
+	if (!func->func) {
+		of_node_put(node);
+		kfree(func);
+		return NULL;
+	}
+
+	return func;
+}
+
+void vexpress_config_func_put(struct vexpress_config_func *func)
+{
+	func->bridge->info->func_put(func->func);
+	of_node_put(func->bridge->node);
+	kfree(func);
+}
+
+
+struct vexpress_config_trans {
+	struct vexpress_config_func *func;
+	int offset;
+	bool write;
+	u32 *data;
+	int status;
+	struct completion completion;
+	struct list_head list;
+};
+
+static void vexpress_config_dump_trans(const char *what,
+		struct vexpress_config_trans *trans)
+{
+	pr_debug("%s %s trans %p func 0x%p offset %d data 0x%x status %d\n",
+			what, trans->write ? "write" : "read", trans,
+			trans->func->func, trans->offset,
+			trans->data ? *trans->data : 0, trans->status);
+}
+
+static int vexpress_config_schedule(struct vexpress_config_trans *trans)
+{
+	int status;
+	struct vexpress_config_bridge *bridge = trans->func->bridge;
+	unsigned long flags;
+
+	init_completion(&trans->completion);
+	trans->status = -EFAULT;
+
+	spin_lock_irqsave(&bridge->transactions_lock, flags);
+
+	vexpress_config_dump_trans("Executing", trans);
+
+	if (list_empty(&bridge->transactions))
+		status = bridge->info->func_exec(trans->func->func,
+				trans->offset, trans->write, trans->data);
+	else
+		status = VEXPRESS_CONFIG_STATUS_WAIT;
+
+	switch (status) {
+	case VEXPRESS_CONFIG_STATUS_DONE:
+		vexpress_config_dump_trans("Finished", trans);
+		trans->status = status;
+		break;
+	case VEXPRESS_CONFIG_STATUS_WAIT:
+		list_add_tail(&trans->list, &bridge->transactions);
+		break;
+	}
+
+	spin_unlock_irqrestore(&bridge->transactions_lock, flags);
+
+	return status;
+}
+
+void vexpress_config_complete(struct vexpress_config_bridge *bridge,
+		int status)
+{
+	struct vexpress_config_trans *trans;
+	unsigned long flags;
+
+	spin_lock_irqsave(&bridge->transactions_lock, flags);
+
+	trans = list_first_entry(&bridge->transactions,
+			struct vexpress_config_trans, list);
+	vexpress_config_dump_trans("Completed", trans);
+
+	trans->status = status;
+	list_del(&trans->list);
+
+	if (!list_empty(&bridge->transactions)) {
+		vexpress_config_dump_trans("Pending", trans);
+
+		bridge->info->func_exec(trans->func->func, trans->offset,
+				trans->write, trans->data);
+	}
+	spin_unlock_irqrestore(&bridge->transactions_lock, flags);
+
+	complete(&trans->completion);
+}
+
+int vexpress_config_wait(struct vexpress_config_trans *trans)
+{
+	wait_for_completion(&trans->completion);
+
+	return trans->status;
+}
+
+
+int vexpress_config_read(struct vexpress_config_func *func, int offset,
+		u32 *data)
+{
+	struct vexpress_config_trans trans = {
+		.func = func,
+		.offset = offset,
+		.write = false,
+		.data = data,
+		.status = 0,
+	};
+	int status = vexpress_config_schedule(&trans);
+
+	if (status == VEXPRESS_CONFIG_STATUS_WAIT)
+		status = vexpress_config_wait(&trans);
+
+	return status;
+}
+EXPORT_SYMBOL(vexpress_config_read);
+
+int vexpress_config_write(struct vexpress_config_func *func, int offset,
+		u32 data)
+{
+	struct vexpress_config_trans trans = {
+		.func = func,
+		.offset = offset,
+		.write = true,
+		.data = &data,
+		.status = 0,
+	};
+	int status = vexpress_config_schedule(&trans);
+
+	if (status == VEXPRESS_CONFIG_STATUS_WAIT)
+		status = vexpress_config_wait(&trans);
+
+	return status;
+}
+EXPORT_SYMBOL(vexpress_config_write);

include/linux/vexpress.h

+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2012 ARM Limited
+ */
+
+#ifndef _LINUX_VEXPRESS_H
+#define _LINUX_VEXPRESS_H
+
+#include <linux/device.h>
+
+#define VEXPRESS_SITE_MB		0
+#define VEXPRESS_SITE_DB1		1
+#define VEXPRESS_SITE_DB2		2
+#define VEXPRESS_SITE_MASTER		0xf
+
+#define VEXPRESS_CONFIG_STATUS_DONE	0
+#define VEXPRESS_CONFIG_STATUS_WAIT	1
+
+#define VEXPRESS_GPIO_MMC_CARDIN	0
+#define VEXPRESS_GPIO_MMC_WPROT		1
+#define VEXPRESS_GPIO_FLASH_WPn		2
+
+#define VEXPRESS_RES_FUNC(_site, _func)	\
+{					\
+	.start = (_site),		\
+	.end = (_func),			\
+	.flags = IORESOURCE_BUS,	\
+}
+
+/* Config bridge API */
+
+/**
+ * struct vexpress_config_bridge_info - description of the platform
+ * configuration infrastructure bridge.
+ *
+ * @name:	Bridge name
+ *
+ * @func_get:	Obtains pointer to a configuration function for a given
+ *		device or a Device Tree node, to be used with @func_put
+ *		and @func_exec. The node pointer should take precedence
+ *		over device pointer when both are passed.
+ *
+ * @func_put:	Tells the bridge that the function will not be used any
+ *		more, so all allocated resources can be released.
+ *
+ * @func_exec:	Executes a configuration function read or write operation.
+ *		The offset selects a 32 bit word of the value accessed.
+ *		Must return VEXPRESS_CONFIG_STATUS_DONE when operation
+ *		is finished immediately, VEXPRESS_CONFIG_STATUS_WAIT when
+ *		will be completed in some time or negative value in case
+ *		of error.
+ */
+struct vexpress_config_bridge_info {
+	const char *name;
+	void *(*func_get)(struct device *dev, struct device_node *node);
+	void (*func_put)(void *func);
+	int (*func_exec)(void *func, int offset, bool write, u32 *data);
+};
+
+struct vexpress_config_bridge;
+
+struct vexpress_config_bridge *vexpress_config_bridge_register(
+		struct device_node *node,
+		struct vexpress_config_bridge_info *info);
+void vexpress_config_bridge_unregister(struct vexpress_config_bridge *bridge);
+
+void vexpress_config_complete(struct vexpress_config_bridge *bridge,
+		int status);
+
+/* Config function API */
+
+struct vexpress_config_func;
+
+struct vexpress_config_func *__vexpress_config_func_get(struct device *dev,
+		struct device_node *node);
+#define vexpress_config_func_get_by_dev(dev) \
+		__vexpress_config_func_get(dev, NULL)
+#define vexpress_config_func_get_by_node(node) \
+		__vexpress_config_func_get(NULL, node)
+void vexpress_config_func_put(struct vexpress_config_func *func);
+
+/* Both may sleep! */
+int vexpress_config_read(struct vexpress_config_func *func, int offset,
+		u32 *data);
+int vexpress_config_write(struct vexpress_config_func *func, int offset,
+		u32 data);
+
+/* Platform control */
+
+u32 vexpress_get_procid(int site);
+u32 vexpress_get_hbi(int site);
+void *vexpress_get_24mhz_clock_base(void);
+void vexpress_flags_set(u32 data);
+
+#define vexpress_get_site_by_node(node) __vexpress_get_site(NULL, node)
+#define vexpress_get_site_by_dev(dev) __vexpress_get_site(dev, NULL)
+unsigned __vexpress_get_site(struct device *dev, struct device_node *node);
+
+void vexpress_sysreg_early_init(void __iomem *base);
+void vexpress_sysreg_of_early_init(void);
+
+void vexpress_power_off(void);
+void vexpress_restart(char str, const char *cmd);
+
+/* Clocks */
+
+struct clk *vexpress_osc_setup(struct device *dev);
+void vexpress_osc_of_setup(struct device_node *node);
+
+void vexpress_clk_init(void __iomem *sp810_base);
+void vexpress_clk_of_init(void);
+
+#endif