tty: serial: amba: cleanup whitespace

Fix whitespace in include/linux/amba/serial.h to match current kernel
coding standards. Fixes about:

 - CHECK: spaces preferred around that '|' (ctx:VxV)
 - ERROR: code indent should use tabs where possible
 - WARNING: Unnecessary space before function pointer arguments
 - WARNING: please, no spaces at the start of a line
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231130-mbly-uart-v5-1-6566703a04b5@bootlin.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

include/linux/amba/serial.h

@@ -75,10 +75,10 @@
 #define UART011_DR_PE		(1 << 9)
 #define UART011_DR_FE		(1 << 8)
 
-#define UART01x_RSR_OE 		0x08
-#define UART01x_RSR_BE 		0x04
-#define UART01x_RSR_PE 		0x02
-#define UART01x_RSR_FE 		0x01
+#define UART01x_RSR_OE		0x08
+#define UART01x_RSR_BE		0x04
+#define UART01x_RSR_PE		0x02
+#define UART01x_RSR_FE		0x01
 
 #define UART011_FR_RI		0x100
 #define UART011_FR_TXFE		0x080
@@ -86,9 +86,9 @@
 #define UART01x_FR_TXFF		0x020
 #define UART01x_FR_RXFE		0x010
 #define UART01x_FR_BUSY		0x008
-#define UART01x_FR_DCD 		0x004
-#define UART01x_FR_DSR 		0x002
-#define UART01x_FR_CTS 		0x001
+#define UART01x_FR_DCD		0x004
+#define UART01x_FR_DSR		0x002
+#define UART01x_FR_CTS		0x001
 #define UART01x_FR_TMSK		(UART01x_FR_TXFF + UART01x_FR_BUSY)
 
 /*
@@ -110,14 +110,14 @@
 #define UART011_CR_TXE		0x0100	/* transmit enable */
 #define UART011_CR_LBE		0x0080	/* loopback enable */
 #define UART010_CR_RTIE		0x0040
-#define UART010_CR_TIE 		0x0020
-#define UART010_CR_RIE 		0x0010
+#define UART010_CR_TIE		0x0020
+#define UART010_CR_RIE		0x0010
 #define UART010_CR_MSIE		0x0008
 #define ST_UART011_CR_OVSFACT	0x0008	/* Oversampling factor */
 #define UART01x_CR_IIRLP	0x0004	/* SIR low power mode */
 #define UART01x_CR_SIREN	0x0002	/* SIR enable */
 #define UART01x_CR_UARTEN	0x0001	/* UART enable */
- 
+
 #define UART011_LCRH_SPS	0x80
 #define UART01x_LCRH_WLEN_8	0x60
 #define UART01x_LCRH_WLEN_7	0x40
@@ -203,8 +203,8 @@
 #define UART011_TXDMAE		(1 << 1)	/* enable transmit dma */
 #define UART011_RXDMAE		(1 << 0)	/* enable receive dma */
 
-#define UART01x_RSR_ANY		(UART01x_RSR_OE|UART01x_RSR_BE|UART01x_RSR_PE|UART01x_RSR_FE)
-#define UART01x_FR_MODEM_ANY	(UART01x_FR_DCD|UART01x_FR_DSR|UART01x_FR_CTS)
+#define UART01x_RSR_ANY		(UART01x_RSR_OE | UART01x_RSR_BE | UART01x_RSR_PE | UART01x_RSR_FE)
+#define UART01x_FR_MODEM_ANY	(UART01x_FR_DCD | UART01x_FR_DSR | UART01x_FR_CTS)
 
 #ifndef __ASSEMBLY__
 struct amba_device; /* in uncompress this is included but amba/bus.h is not */
@@ -220,8 +220,8 @@ struct amba_pl011_data {
 	bool dma_rx_poll_enable;
 	unsigned int dma_rx_poll_rate;
 	unsigned int dma_rx_poll_timeout;
-        void (*init) (void);
-	void (*exit) (void);
+	void (*init)(void);
+	void (*exit)(void);
 };
 #endif