Commit 0aac3f56 authored by Hariprasad Shenai's avatar Hariprasad Shenai Committed by David S. Miller

cxgb4: Add comment for calculate tx flits and sge length code

Add comment for tx filt and sge length calucaltion code, also remove
a hardcoded value
Signed-off-by: default avatarHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent d52ce920
......@@ -730,6 +730,22 @@ static void *alloc_ring(struct device *dev, size_t nelem, size_t elem_size,
*/
static inline unsigned int sgl_len(unsigned int n)
{
/* A Direct Scatter Gather List uses 32-bit lengths and 64-bit PCI DMA
* addresses. The DSGL Work Request starts off with a 32-bit DSGL
* ULPTX header, then Length0, then Address0, then, for 1 <= i <= N,
* repeated sequences of { Length[i], Length[i+1], Address[i],
* Address[i+1] } (this ensures that all addresses are on 64-bit
* boundaries). If N is even, then Length[N+1] should be set to 0 and
* Address[N+1] is omitted.
*
* The following calculation incorporates all of the above. It's
* somewhat hard to follow but, briefly: the "+2" accounts for the
* first two flits which include the DSGL header, Length0 and
* Address0; the "(3*(n-1))/2" covers the main body of list entries (3
* flits for every pair of the remaining N) +1 if (n-1) is odd; and
* finally the "+((n-1)&1)" adds the one remaining flit needed if
* (n-1) is odd ...
*/
n--;
return (3 * n) / 2 + (n & 1) + 2;
}
......@@ -777,12 +793,30 @@ static inline unsigned int calc_tx_flits(const struct sk_buff *skb)
unsigned int flits;
int hdrlen = is_eth_imm(skb);
/* If the skb is small enough, we can pump it out as a work request
* with only immediate data. In that case we just have to have the
* TX Packet header plus the skb data in the Work Request.
*/
if (hdrlen)
return DIV_ROUND_UP(skb->len + hdrlen, sizeof(__be64));
/* Otherwise, we're going to have to construct a Scatter gather list
* of the skb body and fragments. We also include the flits necessary
* for the TX Packet Work Request and CPL. We always have a firmware
* Write Header (incorporated as part of the cpl_tx_pkt_lso and
* cpl_tx_pkt structures), followed by either a TX Packet Write CPL
* message or, if we're doing a Large Send Offload, an LSO CPL message
* with an embedded TX Packet Write CPL message.
*/
flits = sgl_len(skb_shinfo(skb)->nr_frags + 1) + 4;
if (skb_shinfo(skb)->gso_size)
flits += 2;
flits += (sizeof(struct fw_eth_tx_pkt_wr) +
sizeof(struct cpl_tx_pkt_lso_core) +
sizeof(struct cpl_tx_pkt_core)) / sizeof(__be64);
else
flits += (sizeof(struct fw_eth_tx_pkt_wr) +
sizeof(struct cpl_tx_pkt_core)) / sizeof(__be64);
return flits;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment