Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
 "A few new drivers:

   - driver for Azoteq IQS550/572/525 touch controllers

   - driver for Microchip AT42QT1050 keys

   - driver for GPIO controllable vibrators

   - support for GT5663 in Goodix driver

  ... along with miscellaneous driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: libps2 - mark expected switch fall-through
  Input: qt1050 - add Microchip AT42QT1050 support
  Input: add support for Azoteq IQS550/572/525
  Input: add a driver for GPIO controllable vibrators
  Input: synaptics-rmi4 - fix enum_fmt
  Input: synaptics-rmi4 - fill initial format
  HID: input: add mapping for KEY_KBD_LAYOUT_NEXT
  Input: add KEY_KBD_LAYOUT_NEXT
  Input: hyperv-keyboard - add module description
  Input: olpc_apsp - depend on ARCH_MMP
  Input: sun4i-a10-lradc-keys - add support for A83T
  Input: snvs_pwrkey - use dev_pm_set_wake_irq() to simplify code
  Input: lpc32xx-key - add clocks property and fix DT binding example
  Input: i8042 - signal wakeup from atkbd/psmouse
  Input: goodix - add GT5663 CTP support
  Input: goodix - add regulators suppot
  Input: evdev - use struct_size() in kzalloc() and vzalloc()
  Input: edt-ft5x06 - convert to use SPDX identifier
  Input: edt-ft5x06 - enable ACPI enumeration

Documentation/devicetree/bindings/input/gpio-vibrator.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/input/gpio-vibrator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: GPIO vibrator
+
+maintainers:
+  - Luca Weiss <luca@z3ntu.xyz>
+
+description: |+
+  Registers a GPIO device as vibrator, where the on/off capability is controlled by a GPIO.
+
+properties:
+  compatible:
+    const: gpio-vibrator
+
+  enable-gpios:
+    maxItems: 1
+
+  vcc-supply:
+    description: Regulator that provides power
+
+required:
+  - compatible
+  - enable-gpios
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    vibrator {
+        compatible = "gpio-vibrator";
+        enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
+        vcc-supply = <&pm8941_l18>;
+    };

Documentation/devicetree/bindings/input/lpc32xx-key.txt

@@ -8,6 +8,7 @@ Required Properties:
 - reg: Physical base address of the controller and length of memory mapped
   region.
 - interrupts: The interrupt number to the cpu.
+- clocks: phandle to clock controller plus clock-specifier pair
 - nxp,debounce-delay-ms: Debounce delay in ms
 - nxp,scan-delay-ms: Repeated scan period in ms
 - linux,keymap: the key-code to be reported when the key is pressed
@@ -22,7 +23,9 @@ Example:
 	key@40050000 {
 		compatible = "nxp,lpc3220-key";
 		reg = <0x40050000 0x1000>;
-		interrupts = <54 0>;
+		clocks = <&clk LPC32XX_CLK_KEY>;
+		interrupt-parent = <&sic1>;
+		interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
 		keypad,num-rows = <1>;
 		keypad,num-columns = <1>;
 		nxp,debounce-delay-ms = <3>;

Documentation/devicetree/bindings/input/microchip,qt1050.txt

+Microchip AT42QT1050 Five-channel Touch Sensor IC
+
+The AT42QT1050 (QT1050) is a QTouchADC sensor device. The device can sense from
+one to five keys, dependent on mode. The QT1050 includes all signal processing
+functions necessary to provide stable sensing under a wide variety of changing
+conditions, and the outputs are fully debounced.
+
+The touchkey device node should be placed inside an I2C bus node.
+
+Required properties:
+- compatible: Must be "microchip,qt1050"
+- reg: The I2C address of the device
+- interrupts: The sink for the touchpad's IRQ output,
+  see ../interrupt-controller/interrupts.txt
+
+Optional properties:
+- wakeup-source: touch keys can be used as a wakeup source
+
+Each button (key) is represented as a sub-node:
+
+Each not specified key or key with linux,code set to KEY_RESERVED gets disabled
+in HW.
+
+Subnode properties:
+- linux,code: Keycode to emit.
+- reg: The key number. Valid values: 0, 1, 2, 3, 4.
+
+Optional subnode-properties:
+
+If a optional property is missing or has a invalid value the default value is
+taken.
+
+- microchip,pre-charge-time-ns:
+  Each touchpad need some time to precharge. The value depends on the mechanical
+  layout.
+  Valid value range: 0 - 637500; values must be a multiple of 2500;
+  default is 0.
+- microchip,average-samples:
+  Number of data samples which are averaged for each read.
+  Valid values: 1, 4, 16, 64, 256, 1024, 4096, 16384; default is 1.
+- microchip,average-scaling:
+  The scaling factor which is used to scale the average-samples.
+  Valid values: 1, 2, 4, 8, 16, 32, 64, 128; default is 1.
+- microchip,threshold:
+  Number of counts to register a touch detection.
+  Valid value range: 0 - 255; default is 20.
+
+Example:
+QT1050 with 3 non continuous keys, key2 and key4 are disabled.
+
+touchkeys@41 {
+	compatible = "microchip,qt1050";
+	reg = <0x41>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
+
+	up@0 {
+		reg = <0>;
+		linux,code = <KEY_UP>;
+		microchip,average-samples = <64>;
+		microchip,average-scaling = <16>;
+		microchip,pre-charge-time-ns = <10000>;
+	};
+
+	right@1 {
+		reg = <1>;
+		linux,code = <KEY_RIGHT>;
+		microchip,average-samples = <64>;
+		microchip,average-scaling = <8>;
+	};
+
+	down@3 {
+		reg = <3>;
+		linux,code = <KEY_DOWN>;
+		microchip,average-samples = <256>;
+		microchip,average-scaling = <16>;
+	};
+};

Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt

@@ -2,12 +2,14 @@ Allwinner sun4i low res adc attached tablet keys
 ------------------------------------------------
 
 Required properties:
- - compatible: "allwinner,sun4i-a10-lradc-keys"
+ - compatible: should be one of the following string:
+		"allwinner,sun4i-a10-lradc-keys"
+		"allwinner,sun8i-a83t-r-lradc"
  - reg: mmio address range of the chip
  - interrupts: interrupt to which the chip is connected
  - vref-supply: powersupply for the lradc reference voltage
 
-Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys":
+Each key is represented as a sub-node of the compatible mentioned above:
 
 Required subnode-properties:
 	- label: Descriptive name of the key.

Documentation/devicetree/bindings/input/touchscreen/goodix.txt

@@ -3,6 +3,7 @@ Device tree bindings for Goodix GT9xx series touchscreen controller
 Required properties:
 
  - compatible		: Should be "goodix,gt1151"
+				 or "goodix,gt5663"
 				 or "goodix,gt5688"
 				 or "goodix,gt911"
 				 or "goodix,gt9110"
@@ -19,6 +20,8 @@ Optional properties:
  - irq-gpios		: GPIO pin used for IRQ. The driver uses the
 			  interrupt gpio pin as output to reset the device.
  - reset-gpios		: GPIO pin used for reset
+ - AVDD28-supply	: Analog power supply regulator on AVDD28 pin
+ - VDDIO-supply		: GPIO power supply regulator on VDDIO pin
  - touchscreen-inverted-x
  - touchscreen-inverted-y
  - touchscreen-size-x

Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt

+Azoteq IQS550/572/525 Trackpad/Touchscreen Controller
+
+Required properties:
+
+- compatible			: Must be equal to one of the following:
+				  "azoteq,iqs550"
+				  "azoteq,iqs572"
+				  "azoteq,iqs525"
+
+- reg				: I2C slave address for the device.
+
+- interrupts			: GPIO to which the device's active-high RDY
+				  output is connected (see [0]).
+
+- reset-gpios			: GPIO to which the device's active-low NRST
+				  input is connected (see [1]).
+
+Optional properties:
+
+- touchscreen-min-x		: See [2].
+
+- touchscreen-min-y		: See [2].
+
+- touchscreen-size-x		: See [2]. If this property is omitted, the
+				  maximum x-coordinate is specified by the
+				  device's "X Resolution" register.
+
+- touchscreen-size-y		: See [2]. If this property is omitted, the
+				  maximum y-coordinate is specified by the
+				  device's "Y Resolution" register.
+
+- touchscreen-max-pressure	: See [2]. Pressure is expressed as the sum of
+				  the deltas across all channels impacted by a
+				  touch event. A channel's delta is calculated
+				  as its count value minus a reference, where
+				  the count value is inversely proportional to
+				  the channel's capacitance.
+
+- touchscreen-fuzz-x		: See [2].
+
+- touchscreen-fuzz-y		: See [2].
+
+- touchscreen-fuzz-pressure	: See [2].
+
+- touchscreen-inverted-x	: See [2]. Inversion is applied relative to that
+				  which may already be specified by the device's
+				  FLIP_X and FLIP_Y register fields.
+
+- touchscreen-inverted-y	: See [2]. Inversion is applied relative to that
+				  which may already be specified by the device's
+				  FLIP_X and FLIP_Y register fields.
+
+- touchscreen-swapped-x-y	: See [2]. Swapping is applied relative to that
+				  which may already be specified by the device's
+				  SWITCH_XY_AXIS register field.
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+[2]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
+
+Example:
+
+	&i2c1 {
+		/* ... */
+
+		touchscreen@74 {
+			compatible = "azoteq,iqs550";
+			reg = <0x74>;
+			interrupt-parent = <&gpio>;
+			interrupts = <17 4>;
+			reset-gpios = <&gpio 27 1>;
+
+			touchscreen-size-x = <640>;
+			touchscreen-size-y = <480>;
+
+			touchscreen-max-pressure = <16000>;
+		};
+
+		/* ... */
+	};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -55,6 +55,7 @@ avic	Shanghai AVIC Optoelectronics Co., Ltd.
 avnet	Avnet, Inc.
 axentia	Axentia Technologies AB
 axis	Axis Communications AB
+azoteq	Azoteq (Pty) Ltd
 bananapi BIPAI KEJI LIMITED
 bhf	Beckhoff Automation GmbH & Co. KG
 bitmain	Bitmain Technologies

drivers/hid/hid-input.c

@@ -1051,6 +1051,8 @@ static void hidinput_configure_usage(struct hid_input *hidinput, struct hid_fiel
 		case 0x28b: map_key_clear(KEY_FORWARDMAIL);	break;
 		case 0x28c: map_key_clear(KEY_SEND);		break;
 
+		case 0x29d: map_key_clear(KEY_KBD_LAYOUT_NEXT);	break;
+
 		case 0x2c7: map_key_clear(KEY_KBDINPUTASSIST_PREV);		break;
 		case 0x2c8: map_key_clear(KEY_KBDINPUTASSIST_NEXT);		break;
 		case 0x2c9: map_key_clear(KEY_KBDINPUTASSIST_PREVGROUP);		break;

drivers/input/evdev.c

@@ -503,14 +503,13 @@ static int evdev_open(struct inode *inode, struct file *file)
 {
 	struct evdev *evdev = container_of(inode->i_cdev, struct evdev, cdev);
 	unsigned int bufsize = evdev_compute_buffer_size(evdev->handle.dev);
-	unsigned int size = sizeof(struct evdev_client) +
-					bufsize * sizeof(struct input_event);
 	struct evdev_client *client;
 	int error;
 
-	client = kzalloc(size, GFP_KERNEL | __GFP_NOWARN);
+	client = kzalloc(struct_size(client, buffer, bufsize),
+			 GFP_KERNEL | __GFP_NOWARN);
 	if (!client)
-		client = vzalloc(size);
+		client = vzalloc(struct_size(client, buffer, bufsize));
 	if (!client)
 		return -ENOMEM;
 

drivers/input/keyboard/Kconfig

@@ -137,6 +137,17 @@ config KEYBOARD_ATKBD_RDI_KEYCODES
 	  right-hand column will be interpreted as the key shown in the
 	  left-hand column.
 
+config KEYBOARD_QT1050
+	tristate "Microchip AT42QT1050 Touch Sensor Chip"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Say Y here if you want to use Microchip AT42QT1050 QTouch
+	  Sensor chip as input device.
+
+	  To compile this driver as a module, choose M here:
+	  the module will be called qt1050
+
 config KEYBOARD_QT1070
        tristate "Atmel AT42QT1070 Touch Sensor Chip"
        depends on I2C

drivers/input/keyboard/Makefile

@@ -50,6 +50,7 @@ obj-$(CONFIG_KEYBOARD_OPENCORES)	+= opencores-kbd.o
 obj-$(CONFIG_KEYBOARD_PMIC8XXX)		+= pmic8xxx-keypad.o
 obj-$(CONFIG_KEYBOARD_PXA27x)		+= pxa27x_keypad.o
 obj-$(CONFIG_KEYBOARD_PXA930_ROTARY)	+= pxa930_rotary.o
+obj-$(CONFIG_KEYBOARD_QT1050)           += qt1050.o
 obj-$(CONFIG_KEYBOARD_QT1070)           += qt1070.o
 obj-$(CONFIG_KEYBOARD_QT2160)		+= qt2160.o
 obj-$(CONFIG_KEYBOARD_SAMSUNG)		+= samsung-keypad.o

drivers/input/keyboard/atkbd.c

@@ -401,6 +401,8 @@ static irqreturn_t atkbd_interrupt(struct serio *serio, unsigned char data,
 		if  (ps2_handle_response(&atkbd->ps2dev, data))
 			goto out;
 
+	pm_wakeup_event(&serio->dev, 0);
+
 	if (!atkbd->enabled)
 		goto out;
 

drivers/input/keyboard/snvs_pwrkey.c

@@ -15,6 +15,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/platform_device.h>
+#include <linux/pm_wakeirq.h>
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
 
@@ -167,28 +168,9 @@ static int imx_snvs_pwrkey_probe(struct platform_device *pdev)
 	}
 
 	device_init_wakeup(&pdev->dev, pdata->wakeup);
-
-	return 0;
-}
-
-static int __maybe_unused imx_snvs_pwrkey_suspend(struct device *dev)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct pwrkey_drv_data *pdata = platform_get_drvdata(pdev);
-
-	if (device_may_wakeup(&pdev->dev))
-		enable_irq_wake(pdata->irq);
-
-	return 0;
-}
-
-static int __maybe_unused imx_snvs_pwrkey_resume(struct device *dev)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct pwrkey_drv_data *pdata = platform_get_drvdata(pdev);
-
-	if (device_may_wakeup(&pdev->dev))
-		disable_irq_wake(pdata->irq);
+	error = dev_pm_set_wake_irq(&pdev->dev, pdata->irq);
+	if (error)
+		dev_err(&pdev->dev, "irq wake enable failed.\n");
 
 	return 0;
 }
@@ -199,13 +181,9 @@ static const struct of_device_id imx_snvs_pwrkey_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, imx_snvs_pwrkey_ids);
 
-static SIMPLE_DEV_PM_OPS(imx_snvs_pwrkey_pm_ops, imx_snvs_pwrkey_suspend,
-				imx_snvs_pwrkey_resume);
-
 static struct platform_driver imx_snvs_pwrkey_driver = {
 	.driver = {
 		.name = "snvs_pwrkey",
-		.pm     = &imx_snvs_pwrkey_pm_ops,
 		.of_match_table = imx_snvs_pwrkey_ids,
 	},
 	.probe = imx_snvs_pwrkey_probe,

drivers/input/keyboard/sun4i-lradc-keys.c

@@ -46,6 +46,7 @@
 #define CONTINUE_TIME_SEL(x)	((x) << 16) /* 4 bits */
 #define KEY_MODE_SEL(x)		((x) << 12) /* 2 bits */
 #define LEVELA_B_CNT(x)		((x) << 8)  /* 4 bits */
+#define HOLD_KEY_EN(x)		((x) << 7)
 #define HOLD_EN(x)		((x) << 6)
 #define LEVELB_VOL(x)		((x) << 4)  /* 2 bits */
 #define SAMPLE_RATE(x)		((x) << 2)  /* 2 bits */
@@ -63,6 +64,25 @@
 #define	CHAN0_KEYDOWN_IRQ	BIT(1)
 #define CHAN0_DATA_IRQ		BIT(0)
 
+/* struct lradc_variant - Describe sun4i-a10-lradc-keys hardware variant
+ * @divisor_numerator:		The numerator of lradc Vref internally divisor
+ * @divisor_denominator:	The denominator of lradc Vref internally divisor
+ */
+struct lradc_variant {
+	u8 divisor_numerator;
+	u8 divisor_denominator;
+};
+
+static const struct lradc_variant lradc_variant_a10 = {
+	.divisor_numerator = 2,
+	.divisor_denominator = 3
+};
+
+static const struct lradc_variant r_lradc_variant_a83t = {
+	.divisor_numerator = 3,
+	.divisor_denominator = 4
+};
+
 struct sun4i_lradc_keymap {
 	u32 voltage;
 	u32 keycode;
@@ -74,6 +94,7 @@ struct sun4i_lradc_data {
 	void __iomem *base;
 	struct regulator *vref_supply;
 	struct sun4i_lradc_keymap *chan0_map;
+	const struct lradc_variant *variant;
 	u32 chan0_map_count;
 	u32 chan0_keycode;
 	u32 vref;
@@ -128,9 +149,9 @@ static int sun4i_lradc_open(struct input_dev *dev)
 	if (error)
 		return error;
 
-	/* lradc Vref internally is divided by 2/3 */
-	lradc->vref = regulator_get_voltage(lradc->vref_supply) * 2 / 3;
-
+	lradc->vref = regulator_get_voltage(lradc->vref_supply) *
+		      lradc->variant->divisor_numerator /
+		      lradc->variant->divisor_denominator;
 	/*
 	 * Set sample time to 4 ms / 250 Hz. Wait 2 * 4 ms for key to
 	 * stabilize on press, wait (1 + 1) * 4 ms for key release
@@ -222,6 +243,12 @@ static int sun4i_lradc_probe(struct platform_device *pdev)
 	if (error)
 		return error;
 
+	lradc->variant = of_device_get_match_data(&pdev->dev);
+	if (!lradc->variant) {
+		dev_err(&pdev->dev, "Missing sun4i-a10-lradc-keys variant\n");
+		return -EINVAL;
+	}
+
 	lradc->vref_supply = devm_regulator_get(dev, "vref");
 	if (IS_ERR(lradc->vref_supply))
 		return PTR_ERR(lradc->vref_supply);
@@ -265,7 +292,10 @@ static int sun4i_lradc_probe(struct platform_device *pdev)
 }
 
 static const struct of_device_id sun4i_lradc_of_match[] = {
-	{ .compatible = "allwinner,sun4i-a10-lradc-keys", },
+	{ .compatible = "allwinner,sun4i-a10-lradc-keys",
+		.data = &lradc_variant_a10 },
+	{ .compatible = "allwinner,sun8i-a83t-r-lradc",
+		.data = &r_lradc_variant_a83t },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, sun4i_lradc_of_match);

drivers/input/misc/Kconfig

@@ -290,6 +290,18 @@ config INPUT_GPIO_DECODER
 	 To compile this driver as a module, choose M here: the module
 	 will be called gpio_decoder.
 
+config INPUT_GPIO_VIBRA
+	tristate "GPIO vibrator support"
+	depends on GPIOLIB || COMPILE_TEST
+	select INPUT_FF_MEMLESS
+	help
+	  Say Y here to get support for GPIO based vibrator devices.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called gpio-vibra.
+
 config INPUT_IXP4XX_BEEPER
 	tristate "IXP4XX Beeper support"
 	depends on ARCH_IXP4XX

drivers/input/misc/Makefile

@@ -36,6 +36,7 @@ obj-$(CONFIG_INPUT_DRV2667_HAPTICS)	+= drv2667.o
 obj-$(CONFIG_INPUT_GP2A)		+= gp2ap002a00f.o
 obj-$(CONFIG_INPUT_GPIO_BEEPER)		+= gpio-beeper.o
 obj-$(CONFIG_INPUT_GPIO_DECODER)	+= gpio_decoder.o
+obj-$(CONFIG_INPUT_GPIO_VIBRA)		+= gpio-vibra.o
 obj-$(CONFIG_INPUT_HISI_POWERKEY)	+= hisi_powerkey.o
 obj-$(CONFIG_HP_SDC_RTC)		+= hp_sdc_rtc.o
 obj-$(CONFIG_INPUT_IMS_PCU)		+= ims-pcu.o

drivers/input/misc/gpio-vibra.c

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *  GPIO vibrator driver
+ *
+ *  Copyright (C) 2019 Luca Weiss <luca@z3ntu.xyz>
+ *
+ *  Based on PWM vibrator driver:
+ *  Copyright (C) 2017 Collabora Ltd.
+ *
+ *  Based on previous work from:
+ *  Copyright (C) 2012 Dmitry Torokhov <dmitry.torokhov@gmail.com>
+ *
+ *  Based on PWM beeper driver:
+ *  Copyright (C) 2010, Lars-Peter Clausen <lars@metafoo.de>
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/input.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+struct gpio_vibrator {
+	struct input_dev *input;
+	struct gpio_desc *gpio;
+	struct regulator *vcc;
+
+	struct work_struct play_work;
+	bool running;
+	bool vcc_on;
+};
+
+static int gpio_vibrator_start(struct gpio_vibrator *vibrator)
+{
+	struct device *pdev = vibrator->input->dev.parent;
+	int err;
+
+	if (!vibrator->vcc_on) {
+		err = regulator_enable(vibrator->vcc);
+		if (err) {
+			dev_err(pdev, "failed to enable regulator: %d\n", err);
+			return err;
+		}
+		vibrator->vcc_on = true;
+	}
+
+	gpiod_set_value_cansleep(vibrator->gpio, 1);
+
+	return 0;
+}
+
+static void gpio_vibrator_stop(struct gpio_vibrator *vibrator)
+{
+	gpiod_set_value_cansleep(vibrator->gpio, 0);
+
+	if (vibrator->vcc_on) {
+		regulator_disable(vibrator->vcc);
+		vibrator->vcc_on = false;
+	}
+}
+
+static void gpio_vibrator_play_work(struct work_struct *work)
+{
+	struct gpio_vibrator *vibrator =
+		container_of(work, struct gpio_vibrator, play_work);
+
+	if (vibrator->running)
+		gpio_vibrator_start(vibrator);
+	else
+		gpio_vibrator_stop(vibrator);
+}
+
+static int gpio_vibrator_play_effect(struct input_dev *dev, void *data,
+				     struct ff_effect *effect)
+{
+	struct gpio_vibrator *vibrator = input_get_drvdata(dev);
+	int level;
+
+	level = effect->u.rumble.strong_magnitude;
+	if (!level)
+		level = effect->u.rumble.weak_magnitude;
+
+	vibrator->running = level;
+	schedule_work(&vibrator->play_work);
+
+	return 0;
+}
+
+static void gpio_vibrator_close(struct input_dev *input)
+{
+	struct gpio_vibrator *vibrator = input_get_drvdata(input);
+
+	cancel_work_sync(&vibrator->play_work);
+	gpio_vibrator_stop(vibrator);
+	vibrator->running = false;
+}
+
+static int gpio_vibrator_probe(struct platform_device *pdev)
+{
+	struct gpio_vibrator *vibrator;
+	int err;
+
+	vibrator = devm_kzalloc(&pdev->dev, sizeof(*vibrator), GFP_KERNEL);
+	if (!vibrator)
+		return -ENOMEM;
+
+	vibrator->input = devm_input_allocate_device(&pdev->dev);
+	if (!vibrator->input)
+		return -ENOMEM;
+
+	vibrator->vcc = devm_regulator_get(&pdev->dev, "vcc");
+	err = PTR_ERR_OR_ZERO(vibrator->vcc);
+	if (err) {
+		if (err != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Failed to request regulator: %d\n",
+				err);
+		return err;
+	}
+
+	vibrator->gpio = devm_gpiod_get(&pdev->dev, "enable", GPIOD_OUT_LOW);
+	err = PTR_ERR_OR_ZERO(vibrator->gpio);
+	if (err) {
+		if (err != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Failed to request main gpio: %d\n",
+				err);
+		return err;
+	}
+
+	INIT_WORK(&vibrator->play_work, gpio_vibrator_play_work);
+
+	vibrator->input->name = "gpio-vibrator";
+	vibrator->input->id.bustype = BUS_HOST;
+	vibrator->input->close = gpio_vibrator_close;
+
+	input_set_drvdata(vibrator->input, vibrator);
+	input_set_capability(vibrator->input, EV_FF, FF_RUMBLE);
+
+	err = input_ff_create_memless(vibrator->input, NULL,
+				      gpio_vibrator_play_effect);
+	if (err) {
+		dev_err(&pdev->dev, "Couldn't create FF dev: %d\n", err);
+		return err;
+	}
+
+	err = input_register_device(vibrator->input);
+	if (err) {
+		dev_err(&pdev->dev, "Couldn't register input dev: %d\n", err);
+		return err;
+	}
+
+	platform_set_drvdata(pdev, vibrator);
+
+	return 0;
+}
+
+static int __maybe_unused gpio_vibrator_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct gpio_vibrator *vibrator = platform_get_drvdata(pdev);
+
+	cancel_work_sync(&vibrator->play_work);
+	if (vibrator->running)
+		gpio_vibrator_stop(vibrator);
+
+	return 0;
+}
+
+static int __maybe_unused gpio_vibrator_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct gpio_vibrator *vibrator = platform_get_drvdata(pdev);
+
+	if (vibrator->running)
+		gpio_vibrator_start(vibrator);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(gpio_vibrator_pm_ops,
+			 gpio_vibrator_suspend, gpio_vibrator_resume);
+
+#ifdef CONFIG_OF
+static const struct of_device_id gpio_vibra_dt_match_table[] = {
+	{ .compatible = "gpio-vibrator" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, gpio_vibra_dt_match_table);
+#endif
+
+static struct platform_driver gpio_vibrator_driver = {
+	.probe	= gpio_vibrator_probe,
+	.driver	= {
+		.name	= "gpio-vibrator",
+		.pm	= &gpio_vibrator_pm_ops,
+		.of_match_table = of_match_ptr(gpio_vibra_dt_match_table),
+	},
+};
+module_platform_driver(gpio_vibrator_driver);
+
+MODULE_AUTHOR("Luca Weiss <luca@z3ntu.xy>");
+MODULE_DESCRIPTION("GPIO vibrator driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:gpio-vibrator");

drivers/input/mouse/psmouse-base.c

@@ -373,6 +373,8 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
 		if  (ps2_handle_response(&psmouse->ps2dev, data))
 			goto out;
 
+	pm_wakeup_event(&serio->dev, 0);
+
 	if (psmouse->state <= PSMOUSE_RESYNCING)
 		goto out;
 

drivers/input/rmi4/rmi_f54.c

@@ -456,25 +456,15 @@ static int rmi_f54_vidioc_fmt(struct file *file, void *priv,
 static int rmi_f54_vidioc_enum_fmt(struct file *file, void *priv,
 				   struct v4l2_fmtdesc *fmt)
 {
+	struct f54_data *f54 = video_drvdata(file);
+
 	if (fmt->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
 		return -EINVAL;
 
-	switch (fmt->index) {
-	case 0:
-		fmt->pixelformat = V4L2_TCH_FMT_DELTA_TD16;
-		break;
-
-	case 1:
-		fmt->pixelformat = V4L2_TCH_FMT_DELTA_TD08;
-		break;
-
-	case 2:
-		fmt->pixelformat = V4L2_TCH_FMT_TU16;
-		break;
-
-	default:
+	if (fmt->index)
 		return -EINVAL;
-	}
+
+	fmt->pixelformat = f54->format.pixelformat;
 
 	return 0;
 }
@@ -692,6 +682,7 @@ static int rmi_f54_probe(struct rmi_function *fn)
 		return -ENOMEM;
 
 	rmi_f54_create_input_map(f54);
+	rmi_f54_set_input(f54, 0);
 
 	/* register video device */
 	strlcpy(f54->v4l2.name, F54_NAME, sizeof(f54->v4l2.name));

drivers/input/serio/Kconfig

@@ -254,6 +254,7 @@ config SERIO_APBPS2
 
 config SERIO_OLPC_APSP
 	tristate "OLPC AP-SP input support"
+	depends on ARCH_MMP || COMPILE_TEST
 	help
 	  Say Y here if you want support for the keyboard and touchpad included
 	  in the OLPC XO-1.75 and XO-4 laptops.

drivers/input/serio/hyperv-keyboard.c

@@ -440,5 +440,7 @@ static void __exit hv_kbd_exit(void)
 }
 
 MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Microsoft Hyper-V Synthetic Keyboard Driver");
+
 module_init(hv_kbd_init);
 module_exit(hv_kbd_exit);

drivers/input/serio/i8042.c

@@ -573,9 +573,6 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id)
 	port = &i8042_ports[port_no];
 	serio = port->exists ? port->serio : NULL;
 
-	if (irq && serio)
-		pm_wakeup_event(&serio->dev, 0);
-
 	filter_dbg(port->driver_bound, data, "<- i8042 (interrupt, %d, %d%s%s)\n",
 		   port_no, irq,
 		   dfl & SERIO_PARITY ? ", bad parity" : "",

drivers/input/serio/libps2.c

@@ -409,6 +409,7 @@ bool ps2_handle_ack(struct ps2dev *ps2dev, u8 data)
 			ps2dev->nak = PS2_RET_ERR;
 			break;
 		}
+		/* Fall through */
 
 	/*
 	 * Workaround for mice which don't ACK the Get ID command.

drivers/input/touchscreen/Kconfig

@@ -1312,4 +1312,14 @@ config TOUCHSCREEN_ROHM_BU21023
 	  To compile this driver as a module, choose M here: the
 	  module will be called bu21023_ts.
 
+config TOUCHSCREEN_IQS5XX
+	tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
+	depends on I2C
+	help
+	  Say Y to enable support for the Azoteq IQS550/572/525
+	  family of trackpad/touchscreen controllers.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called iqs5xx.
+
 endif

drivers/input/touchscreen/Makefile

@@ -110,3 +110,4 @@ obj-$(CONFIG_TOUCHSCREEN_ZFORCE)	+= zforce_ts.o
 obj-$(CONFIG_TOUCHSCREEN_COLIBRI_VF50)	+= colibri-vf50-ts.o
 obj-$(CONFIG_TOUCHSCREEN_ROHM_BU21023)	+= rohm_bu21023.o
 obj-$(CONFIG_TOUCHSCREEN_RASPBERRYPI_FW)	+= raspberrypi-ts.o
+obj-$(CONFIG_TOUCHSCREEN_IQS5XX)	+= iqs5xx.o

drivers/input/touchscreen/edt-ft5x06.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (C) 2012 Simon Budig, <simon.budig@kernelconcepts.de>
  * Daniel Wagener <daniel.wagener@kernelconcepts.de> (M09 firmware support)
  * Lothar Waßmann <LW@KARO-electronics.de> (DT support)
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public
- * License along with this library; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
 /*
@@ -39,7 +27,6 @@
 #include <linux/gpio/consumer.h>
 #include <linux/input/mt.h>
 #include <linux/input/touchscreen.h>
-#include <linux/of_device.h>
 
 #define WORK_REGISTER_THRESHOLD		0x00
 #define WORK_REGISTER_REPORT_RATE	0x08
@@ -1073,7 +1060,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
 		return -ENOMEM;
 	}
 
-	chip_data = of_device_get_match_data(&client->dev);
+	chip_data = device_get_match_data(&client->dev);
 	if (!chip_data)
 		chip_data = (const struct edt_i2c_chip_data *)id->driver_data;
 	if (!chip_data || !chip_data->max_support_points) {
@@ -1254,7 +1241,6 @@ static const struct i2c_device_id edt_ft5x06_ts_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
 
-#ifdef CONFIG_OF
 static const struct of_device_id edt_ft5x06_of_match[] = {
 	{ .compatible = "edt,edt-ft5206", .data = &edt_ft5x06_data },
 	{ .compatible = "edt,edt-ft5306", .data = &edt_ft5x06_data },
@@ -1266,12 +1252,11 @@ static const struct of_device_id edt_ft5x06_of_match[] = {
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
-#endif
 
 static struct i2c_driver edt_ft5x06_ts_driver = {
 	.driver = {
 		.name = "edt_ft5x06",
-		.of_match_table = of_match_ptr(edt_ft5x06_of_match),
+		.of_match_table = edt_ft5x06_of_match,
 		.pm = &edt_ft5x06_ts_pm_ops,
 	},
 	.id_table = edt_ft5x06_ts_id,
@@ -1283,4 +1268,4 @@ module_i2c_driver(edt_ft5x06_ts_driver);
 
 MODULE_AUTHOR("Simon Budig <simon.budig@kernelconcepts.de>");
 MODULE_DESCRIPTION("EDT FT5x06 I2C Touchscreen Driver");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");

drivers/input/touchscreen/goodix.c

@@ -27,6 +27,7 @@
 #include <linux/delay.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
+#include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/acpi.h>
 #include <linux/of.h>
@@ -47,6 +48,8 @@ struct goodix_ts_data {
 	struct touchscreen_properties prop;
 	unsigned int max_touch_num;
 	unsigned int int_trigger_type;
+	struct regulator *avdd28;
+	struct regulator *vddio;
 	struct gpio_desc *gpiod_int;
 	struct gpio_desc *gpiod_rst;
 	u16 id;
@@ -216,6 +219,7 @@ static const struct goodix_chip_data *goodix_get_chip_data(u16 id)
 {
 	switch (id) {
 	case 1151:
+	case 5663:
 	case 5688:
 		return &gt1x_chip_data;
 
@@ -532,6 +536,24 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
 		return -EINVAL;
 	dev = &ts->client->dev;
 
+	ts->avdd28 = devm_regulator_get(dev, "AVDD28");
+	if (IS_ERR(ts->avdd28)) {
+		error = PTR_ERR(ts->avdd28);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev,
+				"Failed to get AVDD28 regulator: %d\n", error);
+		return error;
+	}
+
+	ts->vddio = devm_regulator_get(dev, "VDDIO");
+	if (IS_ERR(ts->vddio)) {
+		error = PTR_ERR(ts->vddio);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev,
+				"Failed to get VDDIO regulator: %d\n", error);
+		return error;
+	}
+
 	/* Get the interrupt GPIO pin number */
 	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
 	if (IS_ERR(gpiod)) {
@@ -764,6 +786,14 @@ static void goodix_config_cb(const struct firmware *cfg, void *ctx)
 	complete_all(&ts->firmware_loading_complete);
 }
 
+static void goodix_disable_regulators(void *arg)
+{
+	struct goodix_ts_data *ts = arg;
+
+	regulator_disable(ts->vddio);
+	regulator_disable(ts->avdd28);
+}
+
 static int goodix_ts_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
@@ -789,6 +819,29 @@ static int goodix_ts_probe(struct i2c_client *client,
 	if (error)
 		return error;
 
+	/* power up the controller */
+	error = regulator_enable(ts->avdd28);
+	if (error) {
+		dev_err(&client->dev,
+			"Failed to enable AVDD28 regulator: %d\n",
+			error);
+		return error;
+	}
+
+	error = regulator_enable(ts->vddio);
+	if (error) {
+		dev_err(&client->dev,
+			"Failed to enable VDDIO regulator: %d\n",
+			error);
+		regulator_disable(ts->avdd28);
+		return error;
+	}
+
+	error = devm_add_action_or_reset(&client->dev,
+					 goodix_disable_regulators, ts);
+	if (error)
+		return error;
+
 	if (ts->gpiod_int && ts->gpiod_rst) {
 		/* reset the controller */
 		error = goodix_reset(ts);
@@ -945,6 +998,7 @@ MODULE_DEVICE_TABLE(acpi, goodix_acpi_match);
 #ifdef CONFIG_OF
 static const struct of_device_id goodix_of_match[] = {
 	{ .compatible = "goodix,gt1151" },
+	{ .compatible = "goodix,gt5663" },
 	{ .compatible = "goodix,gt5688" },
 	{ .compatible = "goodix,gt911" },
 	{ .compatible = "goodix,gt9110" },

include/uapi/linux/input-event-codes.h

@@ -606,6 +606,7 @@
 #define KEY_SCREENSAVER		0x245	/* AL Screen Saver */
 #define KEY_VOICECOMMAND		0x246	/* Listening Voice Command */
 #define KEY_ASSISTANT		0x247	/* AL Context-aware desktop assistant */
+#define KEY_KBD_LAYOUT_NEXT	0x248	/* AC Next Keyboard Layout Select */
 
 #define KEY_BRIGHTNESS_MIN		0x250	/* Set Brightness to Minimum */
 #define KEY_BRIGHTNESS_MAX		0x251	/* Set Brightness to Maximum */