Merge branch 'pci/pm'

- Remove unused pcibios_pm_ops (Vaibhav Gupta)

- Rename pci_dev.d3_delay to d3hot_delay (Krzysztof Wilczyński)

- Apply D2 transition delay as microseconds, not milliseconds (Bjorn
  Helgaas)

* pci/pm:
  PCI/PM: Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
  PCI/PM: Remove unused PCI_PM_BUS_WAIT
  PCI/PM: Rename pci_dev.d3_delay to d3hot_delay
  PCI/PM: Remove unused pcibios_pm_ops

Documentation/power/pci.rst

@@ -320,7 +320,7 @@ that these callbacks operate on::
 	unsigned int	d2_support:1;	/* Low power state D2 is supported */
 	unsigned int	no_d1d2:1;	/* D1 and D2 are forbidden */
 	unsigned int	wakeup_prepared:1;  /* Device prepared for wake up */
-	unsigned int	d3_delay;	/* D3->D0 transition time in ms */
+	unsigned int	d3hot_delay;	/* D3hot->D0 transition time in ms */
 	...
   };
 

arch/x86/pci/fixup.c

@@ -587,7 +587,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0xa26d, pci_invalid_bar);
 static void pci_fixup_amd_ehci_pme(struct pci_dev *dev)
 {
 	dev_info(&dev->dev, "PME# does not work under D3, disabling it\n");
-	dev->pme_support &= ~((PCI_PM_CAP_PME_D3 | PCI_PM_CAP_PME_D3cold)
+	dev->pme_support &= ~((PCI_PM_CAP_PME_D3hot | PCI_PM_CAP_PME_D3cold)
 		>> PCI_PM_CAP_PME_SHIFT);
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x7808, pci_fixup_amd_ehci_pme);

arch/x86/pci/intel_mid_pci.c

@@ -322,7 +322,7 @@ static void pci_d3delay_fixup(struct pci_dev *dev)
 	 */
 	if (type1_access_ok(dev->bus->number, dev->devfn, PCI_DEVICE_ID))
 		return;
-	dev->d3_delay = 0;
+	dev->d3hot_delay = 0;
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_d3delay_fixup);
 

drivers/hid/intel-ish-hid/ipc/ipc.c

@@ -755,7 +755,7 @@ static int _ish_hw_reset(struct ishtp_device *dev)
 	csr |= PCI_D3hot;
 	pci_write_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, csr);
 
-	mdelay(pdev->d3_delay);
+	mdelay(pdev->d3hot_delay);
 
 	csr &= ~PCI_PM_CTRL_STATE_MASK;
 	csr |= PCI_D0;

drivers/net/ethernet/marvell/sky2.c

@@ -5105,7 +5105,7 @@ static int sky2_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	INIT_WORK(&hw->restart_work, sky2_restart);
 
 	pci_set_drvdata(pdev, hw);
-	pdev->d3_delay = 300;
+	pdev->d3hot_delay = 300;
 
 	return 0;
 

drivers/pci/pci-acpi.c

@@ -1167,7 +1167,7 @@ static struct acpi_device *acpi_pci_find_companion(struct device *dev)
  * @pdev: the PCI device whose delay is to be updated
  * @handle: ACPI handle of this device
  *
- * Update the d3_delay and d3cold_delay of a PCI device from the ACPI _DSM
+ * Update the d3hot_delay and d3cold_delay of a PCI device from the ACPI _DSM
  * control method of either the device itself or the PCI host bridge.
  *
  * Function 8, "Reset Delay," applies to the entire hierarchy below a PCI
@@ -1206,8 +1206,8 @@ static void pci_acpi_optimize_delay(struct pci_dev *pdev,
 		}
 		if (elements[3].type == ACPI_TYPE_INTEGER) {
 			value = (int)elements[3].integer.value / 1000;
-			if (value < PCI_PM_D3_WAIT)
-				pdev->d3_delay = value;
+			if (value < PCI_PM_D3HOT_WAIT)
+				pdev->d3hot_delay = value;
 		}
 	}
 	ACPI_FREE(obj);

drivers/pci/pci-driver.c

@@ -969,12 +969,6 @@ static int pci_pm_resume(struct device *dev)
 
 #ifdef CONFIG_HIBERNATE_CALLBACKS
 
-/*
- * pcibios_pm_ops - provide arch-specific hooks when a PCI device is doing
- * a hibernate transition
- */
-struct dev_pm_ops __weak pcibios_pm_ops;
-
 static int pci_pm_freeze(struct device *dev)
 {
 	struct pci_dev *pci_dev = to_pci_dev(dev);
@@ -1033,9 +1027,6 @@ static int pci_pm_freeze_noirq(struct device *dev)
 
 	pci_pm_set_unknown_state(pci_dev);
 
-	if (pcibios_pm_ops.freeze_noirq)
-		return pcibios_pm_ops.freeze_noirq(dev);
-
 	return 0;
 }
 
@@ -1043,13 +1034,6 @@ static int pci_pm_thaw_noirq(struct device *dev)
 {
 	struct pci_dev *pci_dev = to_pci_dev(dev);
 	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
-	int error;
-
-	if (pcibios_pm_ops.thaw_noirq) {
-		error = pcibios_pm_ops.thaw_noirq(dev);
-		if (error)
-			return error;
-	}
 
 	/*
 	 * The pm->thaw_noirq() callback assumes the device has been
@@ -1174,9 +1158,6 @@ static int pci_pm_poweroff_noirq(struct device *dev)
 
 	pci_fixup_device(pci_fixup_suspend_late, pci_dev);
 
-	if (pcibios_pm_ops.poweroff_noirq)
-		return pcibios_pm_ops.poweroff_noirq(dev);
-
 	return 0;
 }
 
@@ -1184,13 +1165,6 @@ static int pci_pm_restore_noirq(struct device *dev)
 {
 	struct pci_dev *pci_dev = to_pci_dev(dev);
 	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
-	int error;
-
-	if (pcibios_pm_ops.restore_noirq) {
-		error = pcibios_pm_ops.restore_noirq(dev);
-		if (error)
-			return error;
-	}
 
 	pci_pm_default_resume_early(pci_dev);
 	pci_fixup_device(pci_fixup_resume_early, pci_dev);

drivers/pci/pci.c

@@ -49,7 +49,7 @@ EXPORT_SYMBOL(isa_dma_bridge_buggy);
 int pci_pci_problems;
 EXPORT_SYMBOL(pci_pci_problems);
 
-unsigned int pci_pm_d3_delay;
+unsigned int pci_pm_d3hot_delay;
 
 static void pci_pme_list_scan(struct work_struct *work);
 
@@ -66,10 +66,10 @@ struct pci_pme_device {
 
 static void pci_dev_d3_sleep(struct pci_dev *dev)
 {
-	unsigned int delay = dev->d3_delay;
+	unsigned int delay = dev->d3hot_delay;
 
-	if (delay < pci_pm_d3_delay)
-		delay = pci_pm_d3_delay;
+	if (delay < pci_pm_d3hot_delay)
+		delay = pci_pm_d3hot_delay;
 
 	if (delay)
 		msleep(delay);
@@ -1081,7 +1081,7 @@ static int pci_raw_set_power_state(struct pci_dev *dev, pci_power_t state)
 	if (state == PCI_D3hot || dev->current_state == PCI_D3hot)
 		pci_dev_d3_sleep(dev);
 	else if (state == PCI_D2 || dev->current_state == PCI_D2)
-		msleep(PCI_PM_D2_DELAY);
+		udelay(PCI_PM_D2_DELAY);
 
 	pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr);
 	dev->current_state = (pmcsr & PCI_PM_CTRL_STATE_MASK);
@@ -3029,7 +3029,7 @@ void pci_pm_init(struct pci_dev *dev)
 	}
 
 	dev->pm_cap = pm;
-	dev->d3_delay = PCI_PM_D3_WAIT;
+	dev->d3hot_delay = PCI_PM_D3HOT_WAIT;
 	dev->d3cold_delay = PCI_PM_D3COLD_WAIT;
 	dev->bridge_d3 = pci_bridge_d3_possible(dev);
 	dev->d3cold_allowed = true;
@@ -3054,7 +3054,7 @@ void pci_pm_init(struct pci_dev *dev)
 			 (pmc & PCI_PM_CAP_PME_D0) ? " D0" : "",
 			 (pmc & PCI_PM_CAP_PME_D1) ? " D1" : "",
 			 (pmc & PCI_PM_CAP_PME_D2) ? " D2" : "",
-			 (pmc & PCI_PM_CAP_PME_D3) ? " D3hot" : "",
+			 (pmc & PCI_PM_CAP_PME_D3hot) ? " D3hot" : "",
 			 (pmc & PCI_PM_CAP_PME_D3cold) ? " D3cold" : "");
 		dev->pme_support = pmc >> PCI_PM_CAP_PME_SHIFT;
 		dev->pme_poll = true;
@@ -4637,7 +4637,7 @@ static int pci_af_flr(struct pci_dev *dev, int probe)
  *
  * NOTE: This causes the caller to sleep for twice the device power transition
  * cooldown period, which for the D0->D3hot and D3hot->D0 transitions is 10 ms
- * by default (i.e. unless the @dev's d3_delay field has a different value).
+ * by default (i.e. unless the @dev's d3hot_delay field has a different value).
  * Moreover, only devices in D0 can be reset by this function.
  */
 static int pci_pm_reset(struct pci_dev *dev, int probe)

drivers/pci/pci.h

@@ -43,10 +43,9 @@ int pci_probe_reset_function(struct pci_dev *dev);
 int pci_bridge_secondary_bus_reset(struct pci_dev *dev);
 int pci_bus_error_reset(struct pci_dev *dev);
 
-#define PCI_PM_D2_DELAY         200
-#define PCI_PM_D3_WAIT          10
-#define PCI_PM_D3COLD_WAIT      100
-#define PCI_PM_BUS_WAIT         50
+#define PCI_PM_D2_DELAY         200	/* usec; see PCIe r4.0, sec 5.9.1 */
+#define PCI_PM_D3HOT_WAIT       10	/* msec */
+#define PCI_PM_D3COLD_WAIT      100	/* msec */
 
 /**
  * struct pci_platform_pm_ops - Firmware PM callbacks
@@ -178,7 +177,7 @@ extern struct mutex pci_slot_mutex;
 
 extern raw_spinlock_t pci_lock;
 
-extern unsigned int pci_pm_d3_delay;
+extern unsigned int pci_pm_d3hot_delay;
 
 #ifdef CONFIG_PCI_MSI
 void pci_no_msi(void);

drivers/pci/quirks.c

@@ -1846,7 +1846,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_PXHV,	quirk_pci
  */
 static void quirk_intel_pcie_pm(struct pci_dev *dev)
 {
-	pci_pm_d3_delay = 120;
+	pci_pm_d3hot_delay = 120;
 	dev->no_d1d2 = 1;
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,	0x25e2, quirk_intel_pcie_pm);
@@ -1873,12 +1873,12 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,	0x260b, quirk_intel_pcie_pm);
 
 static void quirk_d3hot_delay(struct pci_dev *dev, unsigned int delay)
 {
-	if (dev->d3_delay >= delay)
+	if (dev->d3hot_delay >= delay)
 		return;
 
-	dev->d3_delay = delay;
+	dev->d3hot_delay = delay;
 	pci_info(dev, "extending delay after power-on from D3hot to %d msec\n",
-		 dev->d3_delay);
+		 dev->d3hot_delay);
 }
 
 static void quirk_radeon_pm(struct pci_dev *dev)
@@ -3387,36 +3387,36 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0152, disable_igfx_irq);
  * PCI devices which are on Intel chips can skip the 10ms delay
  * before entering D3 mode.
  */
-static void quirk_remove_d3_delay(struct pci_dev *dev)
-{
-	dev->d3_delay = 0;
-}
-/* C600 Series devices do not need 10ms d3_delay */
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0412, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c00, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c0c, quirk_remove_d3_delay);
-/* Lynxpoint-H PCH devices do not need 10ms d3_delay */
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c02, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c18, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c1c, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c20, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c22, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c26, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c2d, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c31, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3a, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3d, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c4e, quirk_remove_d3_delay);
-/* Intel Cherrytrail devices do not need 10ms d3_delay */
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2280, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2298, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x229c, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b0, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b5, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b7, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b8, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22d8, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22dc, quirk_remove_d3_delay);
+static void quirk_remove_d3hot_delay(struct pci_dev *dev)
+{
+	dev->d3hot_delay = 0;
+}
+/* C600 Series devices do not need 10ms d3hot_delay */
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0412, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c00, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c0c, quirk_remove_d3hot_delay);
+/* Lynxpoint-H PCH devices do not need 10ms d3hot_delay */
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c02, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c18, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c1c, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c20, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c22, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c26, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c2d, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c31, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3a, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3d, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c4e, quirk_remove_d3hot_delay);
+/* Intel Cherrytrail devices do not need 10ms d3hot_delay */
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2280, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2298, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x229c, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b0, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b5, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b7, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b8, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22d8, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22dc, quirk_remove_d3hot_delay);
 
 /*
  * Some devices may pass our check in pci_intx_mask_supported() if

drivers/staging/media/atomisp/pci/atomisp_v4l2.c

@@ -1573,7 +1573,7 @@ static int atomisp_pci_probe(struct pci_dev *pdev, const struct pci_device_id *i
 	spin_lock_init(&isp->lock);
 
 	/* This is not a true PCI device on SoC, so the delay is not needed. */
-	pdev->d3_delay = 0;
+	pdev->d3hot_delay = 0;
 
 	pci_set_drvdata(pdev, isp);
 

include/linux/pci.h

@@ -373,7 +373,7 @@ struct pci_dev {
 						      user sysfs */
 	unsigned int	clear_retrain_link:1;	/* Need to clear Retrain Link
 						   bit manually */
-	unsigned int	d3_delay;	/* D3->D0 transition time in ms */
+	unsigned int	d3hot_delay;	/* D3hot->D0 transition time in ms */
 	unsigned int	d3cold_delay;	/* D3cold->D0 transition time in ms */
 
 #ifdef CONFIG_PCIEASPM
@@ -2035,10 +2035,6 @@ int pcibios_alloc_irq(struct pci_dev *dev);
 void pcibios_free_irq(struct pci_dev *dev);
 resource_size_t pcibios_default_alignment(void);
 
-#ifdef CONFIG_HIBERNATE_CALLBACKS
-extern struct dev_pm_ops pcibios_pm_ops;
-#endif
-
 #if defined(CONFIG_PCI_MMCONFIG) || defined(CONFIG_ACPI_MCFG)
 void __init pci_mmcfg_early_init(void);
 void __init pci_mmcfg_late_init(void);

include/uapi/linux/pci_regs.h

@@ -246,7 +246,7 @@
 #define  PCI_PM_CAP_PME_D0	0x0800	/* PME# from D0 */
 #define  PCI_PM_CAP_PME_D1	0x1000	/* PME# from D1 */
 #define  PCI_PM_CAP_PME_D2	0x2000	/* PME# from D2 */
-#define  PCI_PM_CAP_PME_D3	0x4000	/* PME# from D3 (hot) */
+#define  PCI_PM_CAP_PME_D3hot	0x4000	/* PME# from D3 (hot) */
 #define  PCI_PM_CAP_PME_D3cold	0x8000	/* PME# from D3 (cold) */
 #define  PCI_PM_CAP_PME_SHIFT	11	/* Start of the PME Mask in PMC */
 #define PCI_PM_CTRL		4	/* PM control and status register */