Manual merge of rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6.git

This is a fixed-up version of the broken "upstream-2.6.13" branch, where
I re-did the manual merge of drivers/net/r8169.c by hand, and made sure
the history is all good.

Documentation/networking/generic-hdlc.txt

 Generic HDLC layer
 Krzysztof Halasa <khc@pm.waw.pl>
-January, 2003
 
 
 Generic HDLC layer currently supports:
-- Frame Relay (ANSI, CCITT and no LMI), with ARP support (no InARP).
-  Normal (routed) and Ethernet-bridged (Ethernet device emulation)
-  interfaces can share a single PVC.
-- raw HDLC - either IP (IPv4) interface or Ethernet device emulation.
-- Cisco HDLC,
-- PPP (uses syncppp.c),
-- X.25 (uses X.25 routines).
-
-There are hardware drivers for the following cards:
-- C101 by Moxa Technologies Co., Ltd.
-- RISCom/N2 by SDL Communications Inc.
-- and others, some not in the official kernel.
+1. Frame Relay (ANSI, CCITT, Cisco and no LMI).
+   - Normal (routed) and Ethernet-bridged (Ethernet device emulation)
+     interfaces can share a single PVC.
+   - ARP support (no InARP support in the kernel - there is an
+     experimental InARP user-space daemon available on:
+     http://www.kernel.org/pub/linux/utils/net/hdlc/).
+2. raw HDLC - either IP (IPv4) interface or Ethernet device emulation.
+3. Cisco HDLC.
+4. PPP (uses syncppp.c).
+5. X.25 (uses X.25 routines).
+
+Generic HDLC is a protocol driver only - it needs a low-level driver
+for your particular hardware.
 
 Ethernet device emulation (using HDLC or Frame-Relay PVC) is compatible
 with IEEE 802.1Q (VLANs) and 802.1D (Ethernet bridging).
@@ -24,7 +24,7 @@ with IEEE 802.1Q (VLANs) and 802.1D (Ethernet bridging).
 Make sure the hdlc.o and the hardware driver are loaded. It should
 create a number of "hdlc" (hdlc0 etc) network devices, one for each
 WAN port. You'll need the "sethdlc" utility, get it from:
-	http://hq.pm.waw.pl/hdlc/
+	http://www.kernel.org/pub/linux/utils/net/hdlc/
 
 Compile sethdlc.c utility:
 	gcc -O2 -Wall -o sethdlc sethdlc.c
@@ -52,12 +52,12 @@ Setting interface:
 * v35 | rs232 | x21 | t1 | e1 - sets physical interface for a given port
                                 if the card has software-selectable interfaces
   loopback - activate hardware loopback (for testing only)
-* clock ext - external clock (uses DTE RX and TX clock)
-* clock int - internal clock (provides clock signal on DCE clock output)
-* clock txint - TX internal, RX external (provides TX clock on DCE output)
-* clock txfromrx - TX clock derived from RX clock (TX clock on DCE output)
-* rate - sets clock rate in bps (not required for external clock or
-                                 for txfromrx)
+* clock ext - both RX clock and TX clock external
+* clock int - both RX clock and TX clock internal
+* clock txint - RX clock external, TX clock internal
+* clock txfromrx - RX clock external, TX clock derived from RX clock
+* rate - sets clock rate in bps (for "int" or "txint" clock only)
+
 
 Setting protocol:
 
@@ -79,7 +79,7 @@ Setting protocol:
 * x25 - sets X.25 mode
 
 * fr - Frame Relay mode
-  lmi ansi / ccitt / none - LMI (link management) type
+  lmi ansi / ccitt / cisco / none - LMI (link management) type
   dce - Frame Relay DCE (network) side LMI instead of default DTE (user).
   It has nothing to do with clocks!
   t391 - link integrity verification polling timer (in seconds) - user
@@ -119,13 +119,14 @@ or
 
 
 
-If you have a problem with N2 or C101 card, you can issue the "private"
-command to see port's packet descriptor rings (in kernel logs):
+If you have a problem with N2, C101 or PLX200SYN card, you can issue the
+"private" command to see port's packet descriptor rings (in kernel logs):
 
 	sethdlc hdlc0 private
 
-The hardware driver has to be build with CONFIG_HDLC_DEBUG_RINGS.
+The hardware driver has to be build with #define DEBUG_RINGS.
 Attaching this info to bug reports would be helpful. Anyway, let me know
 if you have problems using this.
 
-For patches and other info look at http://hq.pm.waw.pl/hdlc/
+For patches and other info look at:
+<http://www.kernel.org/pub/linux/utils/net/hdlc/>.

Documentation/networking/multicast.txt

@@ -47,7 +47,6 @@ ni52		<------------------ Buggy ------------------>
 ni65		YES		YES		YES		Software(#)
 seeq		NO		NO		NO		N/A
 sgiseek		<------------------ Buggy ------------------>
-sk_g16		NO		NO		YES		N/A
 smc-ultra	YES		YES		YES		Hardware
 sunlance	YES		YES		YES		Hardware
 tulip		YES		YES		YES		Hardware

Documentation/networking/net-modules.txt

@@ -284,9 +284,6 @@ ppp.c:
 seeq8005.c: *Not modularized*
 	(Probes ports: 0x300, 0x320, 0x340, 0x360)
 
-sk_g16.c: *Not modularized*
-	(Probes ports: 0x100, 0x180, 0x208, 0x220m 0x288, 0x320, 0x328, 0x390)
-
 skeleton.c: *Skeleton*
 
 slhc.c:

drivers/net/8139cp.c

@@ -54,6 +54,7 @@
 
 #include <linux/config.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/kernel.h>
 #include <linux/compiler.h>
 #include <linux/netdevice.h>
@@ -91,16 +92,17 @@ KERN_INFO DRV_NAME ": 10/100 PCI Ethernet driver v" DRV_VERSION " (" DRV_RELDATE
 
 MODULE_AUTHOR("Jeff Garzik <jgarzik@pobox.com>");
 MODULE_DESCRIPTION("RealTek RTL-8139C+ series 10/100 PCI Ethernet driver");
+MODULE_VERSION(DRV_VERSION);
 MODULE_LICENSE("GPL");
 
 static int debug = -1;
-MODULE_PARM (debug, "i");
+module_param(debug, int, 0);
 MODULE_PARM_DESC (debug, "8139cp: bitmapped message enable number");
 
 /* Maximum number of multicast addresses to filter (vs. Rx-all-multicast).
    The RTL chips use a 64 element hash table based on the Ethernet CRC.  */
 static int multicast_filter_limit = 32;
-MODULE_PARM (multicast_filter_limit, "i");
+module_param(multicast_filter_limit, int, 0);
 MODULE_PARM_DESC (multicast_filter_limit, "8139cp: maximum number of filtered multicast addresses");
 
 #define PFX			DRV_NAME ": "
@@ -186,6 +188,9 @@ enum {
 	RingEnd		= (1 << 30), /* End of descriptor ring */
 	FirstFrag	= (1 << 29), /* First segment of a packet */
 	LastFrag	= (1 << 28), /* Final segment of a packet */
+	LargeSend	= (1 << 27), /* TCP Large Send Offload (TSO) */
+	MSSShift	= 16,	     /* MSS value position */
+	MSSMask		= 0xfff,     /* MSS value: 11 bits */
 	TxError		= (1 << 23), /* Tx error summary */
 	RxError		= (1 << 20), /* Rx error summary */
 	IPCS		= (1 << 18), /* Calculate IP checksum */
@@ -312,7 +317,7 @@ struct cp_desc {
 struct ring_info {
 	struct sk_buff		*skb;
 	dma_addr_t		mapping;
-	unsigned		frag;
+	u32			len;
 };
 
 struct cp_dma_stats {
@@ -394,6 +399,9 @@ struct cp_private {
 static void __cp_set_rx_mode (struct net_device *dev);
 static void cp_tx (struct cp_private *cp);
 static void cp_clean_rings (struct cp_private *cp);
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void cp_poll_controller(struct net_device *dev);
+#endif
 
 static struct pci_device_id cp_pci_tbl[] = {
 	{ PCI_VENDOR_ID_REALTEK, PCI_DEVICE_ID_REALTEK_8139,
@@ -688,6 +696,19 @@ cp_interrupt (int irq, void *dev_instance, struct pt_regs *regs)
 	return IRQ_HANDLED;
 }
 
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/*
+ * Polling receive - used by netconsole and other diagnostic tools
+ * to allow network i/o with interrupts disabled.
+ */
+static void cp_poll_controller(struct net_device *dev)
+{
+	disable_irq(dev->irq);
+	cp_interrupt(dev->irq, dev, NULL);
+	enable_irq(dev->irq);
+}
+#endif
+
 static void cp_tx (struct cp_private *cp)
 {
 	unsigned tx_head = cp->tx_head;
@@ -707,7 +728,7 @@ static void cp_tx (struct cp_private *cp)
 			BUG();
 
 		pci_unmap_single(cp->pdev, cp->tx_skb[tx_tail].mapping,
-					skb->len, PCI_DMA_TODEVICE);
+				 cp->tx_skb[tx_tail].len, PCI_DMA_TODEVICE);
 
 		if (status & LastFrag) {
 			if (status & (TxError | TxFIFOUnder)) {
@@ -749,10 +770,11 @@ static int cp_start_xmit (struct sk_buff *skb, struct net_device *dev)
 {
 	struct cp_private *cp = netdev_priv(dev);
 	unsigned entry;
-	u32 eor;
+	u32 eor, flags;
 #if CP_VLAN_TAG_USED
 	u32 vlan_tag = 0;
 #endif
+	int mss = 0;
 
 	spin_lock_irq(&cp->lock);
 
@@ -772,6 +794,9 @@ static int cp_start_xmit (struct sk_buff *skb, struct net_device *dev)
 
 	entry = cp->tx_head;
 	eor = (entry == (CP_TX_RING_SIZE - 1)) ? RingEnd : 0;
+	if (dev->features & NETIF_F_TSO)
+		mss = skb_shinfo(skb)->tso_size;
+
 	if (skb_shinfo(skb)->nr_frags == 0) {
 		struct cp_desc *txd = &cp->tx_ring[entry];
 		u32 len;
@@ -783,26 +808,26 @@ static int cp_start_xmit (struct sk_buff *skb, struct net_device *dev)
 		txd->addr = cpu_to_le64(mapping);
 		wmb();
 
-		if (skb->ip_summed == CHECKSUM_HW) {
+		flags = eor | len | DescOwn | FirstFrag | LastFrag;
+
+		if (mss)
+			flags |= LargeSend | ((mss & MSSMask) << MSSShift);
+		else if (skb->ip_summed == CHECKSUM_HW) {
 			const struct iphdr *ip = skb->nh.iph;
 			if (ip->protocol == IPPROTO_TCP)
-				txd->opts1 = cpu_to_le32(eor | len | DescOwn |
-							 FirstFrag | LastFrag |
-							 IPCS | TCPCS);
+				flags |= IPCS | TCPCS;
 			else if (ip->protocol == IPPROTO_UDP)
-				txd->opts1 = cpu_to_le32(eor | len | DescOwn |
-							 FirstFrag | LastFrag |
-							 IPCS | UDPCS);
+				flags |= IPCS | UDPCS;
 			else
-				BUG();
-		} else
-			txd->opts1 = cpu_to_le32(eor | len | DescOwn |
-						 FirstFrag | LastFrag);
+				WARN_ON(1);	/* we need a WARN() */
+		}
+
+		txd->opts1 = cpu_to_le32(flags);
 		wmb();
 
 		cp->tx_skb[entry].skb = skb;
 		cp->tx_skb[entry].mapping = mapping;
-		cp->tx_skb[entry].frag = 0;
+		cp->tx_skb[entry].len = len;
 		entry = NEXT_TX(entry);
 	} else {
 		struct cp_desc *txd;
@@ -820,7 +845,7 @@ static int cp_start_xmit (struct sk_buff *skb, struct net_device *dev)
 					       first_len, PCI_DMA_TODEVICE);
 		cp->tx_skb[entry].skb = skb;
 		cp->tx_skb[entry].mapping = first_mapping;
-		cp->tx_skb[entry].frag = 1;
+		cp->tx_skb[entry].len = first_len;
 		entry = NEXT_TX(entry);
 
 		for (frag = 0; frag < skb_shinfo(skb)->nr_frags; frag++) {
@@ -836,16 +861,19 @@ static int cp_start_xmit (struct sk_buff *skb, struct net_device *dev)
 						 len, PCI_DMA_TODEVICE);
 			eor = (entry == (CP_TX_RING_SIZE - 1)) ? RingEnd : 0;
 
-			if (skb->ip_summed == CHECKSUM_HW) {
-				ctrl = eor | len | DescOwn | IPCS;
+			ctrl = eor | len | DescOwn;
+
+			if (mss)
+				ctrl |= LargeSend |
+					((mss & MSSMask) << MSSShift);
+			else if (skb->ip_summed == CHECKSUM_HW) {
 				if (ip->protocol == IPPROTO_TCP)
-					ctrl |= TCPCS;
+					ctrl |= IPCS | TCPCS;
 				else if (ip->protocol == IPPROTO_UDP)
-					ctrl |= UDPCS;
+					ctrl |= IPCS | UDPCS;
 				else
 					BUG();
-			} else
-				ctrl = eor | len | DescOwn;
+			}
 
 			if (frag == skb_shinfo(skb)->nr_frags - 1)
 				ctrl |= LastFrag;
@@ -860,7 +888,7 @@ static int cp_start_xmit (struct sk_buff *skb, struct net_device *dev)
 
 			cp->tx_skb[entry].skb = skb;
 			cp->tx_skb[entry].mapping = mapping;
-			cp->tx_skb[entry].frag = frag + 2;
+			cp->tx_skb[entry].len = len;
 			entry = NEXT_TX(entry);
 		}
 
@@ -1074,7 +1102,6 @@ static int cp_refill_rx (struct cp_private *cp)
 		cp->rx_skb[i].mapping = pci_map_single(cp->pdev,
 			skb->tail, cp->rx_buf_sz, PCI_DMA_FROMDEVICE);
 		cp->rx_skb[i].skb = skb;
-		cp->rx_skb[i].frag = 0;
 
 		cp->rx_ring[i].opts2 = 0;
 		cp->rx_ring[i].addr = cpu_to_le64(cp->rx_skb[i].mapping);
@@ -1126,9 +1153,6 @@ static void cp_clean_rings (struct cp_private *cp)
 {
 	unsigned i;
 
-	memset(cp->rx_ring, 0, sizeof(struct cp_desc) * CP_RX_RING_SIZE);
-	memset(cp->tx_ring, 0, sizeof(struct cp_desc) * CP_TX_RING_SIZE);
-
 	for (i = 0; i < CP_RX_RING_SIZE; i++) {
 		if (cp->rx_skb[i].skb) {
 			pci_unmap_single(cp->pdev, cp->rx_skb[i].mapping,
@@ -1140,13 +1164,18 @@ static void cp_clean_rings (struct cp_private *cp)
 	for (i = 0; i < CP_TX_RING_SIZE; i++) {
 		if (cp->tx_skb[i].skb) {
 			struct sk_buff *skb = cp->tx_skb[i].skb;
+
 			pci_unmap_single(cp->pdev, cp->tx_skb[i].mapping,
-					 skb->len, PCI_DMA_TODEVICE);
-			dev_kfree_skb(skb);
+				 	 cp->tx_skb[i].len, PCI_DMA_TODEVICE);
+			if (le32_to_cpu(cp->tx_ring[i].opts1) & LastFrag)
+				dev_kfree_skb(skb);
 			cp->net_stats.tx_dropped++;
 		}
 	}
 
+	memset(cp->rx_ring, 0, sizeof(struct cp_desc) * CP_RX_RING_SIZE);
+	memset(cp->tx_ring, 0, sizeof(struct cp_desc) * CP_TX_RING_SIZE);
+
 	memset(&cp->rx_skb, 0, sizeof(struct ring_info) * CP_RX_RING_SIZE);
 	memset(&cp->tx_skb, 0, sizeof(struct ring_info) * CP_TX_RING_SIZE);
 }
@@ -1538,6 +1567,8 @@ static struct ethtool_ops cp_ethtool_ops = {
 	.set_tx_csum		= ethtool_op_set_tx_csum, /* local! */
 	.get_sg			= ethtool_op_get_sg,
 	.set_sg			= ethtool_op_set_sg,
+	.get_tso		= ethtool_op_get_tso,
+	.set_tso		= ethtool_op_set_tso,
 	.get_regs		= cp_get_regs,
 	.get_wol		= cp_get_wol,
 	.set_wol		= cp_set_wol,
@@ -1749,6 +1780,9 @@ static int cp_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	dev->get_stats = cp_get_stats;
 	dev->do_ioctl = cp_ioctl;
 	dev->poll = cp_rx_poll;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+	dev->poll_controller = cp_poll_controller;
+#endif
 	dev->weight = 16;	/* arbitrary? from NAPI_HOWTO.txt. */
 #ifdef BROKEN
 	dev->change_mtu = cp_change_mtu;
@@ -1768,6 +1802,10 @@ static int cp_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (pci_using_dac)
 		dev->features |= NETIF_F_HIGHDMA;
 
+#if 0 /* disabled by default until verified */
+	dev->features |= NETIF_F_TSO;
+#endif
+
 	dev->irq = pdev->irq;
 
 	rc = register_netdev(dev);

drivers/net/Kconfig

@@ -824,6 +824,18 @@ config SMC9194
 	  <file:Documentation/networking/net-modules.txt>. The module
 	  will be called smc9194.
 
+config DM9000
+	tristate "DM9000 support"
+	depends on ARM && NET_ETHERNET
+	select CRC32
+	select MII
+	---help---
+	  Support for DM9000 chipset.
+
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will be
+	  called dm9000.
+
 config NET_VENDOR_RACAL
 	bool "Racal-Interlan (Micom) NI cards"
 	depends on NET_ETHERNET && ISA
@@ -989,21 +1001,6 @@ config EEXPRESS_PRO
 	  <file:Documentation/networking/net-modules.txt>. The module
 	  will be called eepro.
 
-config FMV18X
-	tristate "FMV-181/182/183/184 support (OBSOLETE)"
-	depends on NET_ISA && OBSOLETE
-	---help---
-	  If you have a Fujitsu FMV-181/182/183/184 network (Ethernet) card,
-	  say Y and read the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
-
-	  If you use an FMV-183 or FMV-184 and it is not working, you may need
-	  to disable Plug & Play mode of the card.
-
-	  To compile this driver as a module, choose M here and read
-	  <file:Documentation/networking/net-modules.txt>. The module
-	  will be called fmv18x.
-
 config HPLAN_PLUS
 	tristate "HP PCLAN+ (27247B and 27252A) support"
 	depends on NET_ISA
@@ -1092,14 +1089,6 @@ config SEEQ8005
 	  <file:Documentation/networking/net-modules.txt>. The module
 	  will be called seeq8005.
 
-config SK_G16
-	tristate "SK_G16 support (OBSOLETE)"
-	depends on NET_ISA && OBSOLETE
-	help
-	  If you have a network (Ethernet) card of this type, say Y and read
-	  the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
-
 config SKMC
 	tristate "SKnet MCA support"
 	depends on NET_ETHERNET && MCA && BROKEN
@@ -1932,6 +1921,18 @@ config R8169_VLAN
 	  
 	  If in doubt, say Y.
 
+config SKGE
+	tristate "New SysKonnect GigaEthernet support (EXPERIMENTAL)"
+	depends on PCI && EXPERIMENTAL
+	select CRC32
+	---help---
+	  This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
+	  and related Gigabit Ethernet adapters. It is a new smaller driver
+	  driver with better performance and more complete ethtool support.
+
+	  It does not support the link failover and network management 
+	  features that "portable" vendor supplied sk98lin driver does.
+	
 config SK98LIN
 	tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
 	depends on PCI

drivers/net/Makefile

@@ -53,6 +53,7 @@ obj-$(CONFIG_FEALNX) += fealnx.o
 obj-$(CONFIG_TIGON3) += tg3.o
 obj-$(CONFIG_BNX2) += bnx2.o
 obj-$(CONFIG_TC35815) += tc35815.o
+obj-$(CONFIG_SKGE) += skge.o
 obj-$(CONFIG_SK98LIN) += sk98lin/
 obj-$(CONFIG_SKFP) += skfp/
 obj-$(CONFIG_VIA_RHINE) += via-rhine.o
@@ -74,7 +75,6 @@ obj-$(CONFIG_MAC8390) += mac8390.o 8390.o
 obj-$(CONFIG_APNE) += apne.o 8390.o
 obj-$(CONFIG_PCMCIA_PCNET) += 8390.o
 obj-$(CONFIG_SHAPER) += shaper.o
-obj-$(CONFIG_SK_G16) += sk_g16.o
 obj-$(CONFIG_HP100) += hp100.o
 obj-$(CONFIG_SMC9194) += smc9194.o
 obj-$(CONFIG_FEC) += fec.o
@@ -122,7 +122,6 @@ obj-$(CONFIG_DEFXX) += defxx.o
 obj-$(CONFIG_SGISEEQ) += sgiseeq.o
 obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
 obj-$(CONFIG_AT1700) += at1700.o
-obj-$(CONFIG_FMV18X) += fmv18x.o
 obj-$(CONFIG_EL1) += 3c501.o
 obj-$(CONFIG_EL16) += 3c507.o
 obj-$(CONFIG_ELMC) += 3c523.o
@@ -180,6 +179,7 @@ obj-$(CONFIG_AMD8111_ETH) += amd8111e.o
 obj-$(CONFIG_IBMVETH) += ibmveth.o
 obj-$(CONFIG_S2IO) += s2io.o
 obj-$(CONFIG_SMC91X) += smc91x.o
+obj-$(CONFIG_DM9000) += dm9000.o
 obj-$(CONFIG_FEC_8XX) += fec_8xx/
 
 obj-$(CONFIG_ARM) += arm/

drivers/net/Space.c

@@ -210,9 +210,6 @@ static struct devprobe2 isa_probes[] __initdata = {
 #ifdef CONFIG_AT1700
 	{at1700_probe, 0},
 #endif
-#ifdef CONFIG_FMV18X		/* Fujitsu FMV-181/182 */
-	{fmv18x_probe, 0},
-#endif
 #ifdef CONFIG_ETH16I
 	{eth16i_probe, 0},	/* ICL EtherTeam 16i/32 */
 #endif
@@ -243,9 +240,6 @@ static struct devprobe2 isa_probes[] __initdata = {
 #ifdef CONFIG_ELPLUS		/* 3c505 */
 	{elplus_probe, 0},
 #endif
-#ifdef CONFIG_SK_G16
-	{SK_init, 0},
-#endif
 #ifdef CONFIG_NI5010
 	{ni5010_probe, 0},
 #endif

drivers/net/arm/etherh.c

@@ -68,6 +68,7 @@ struct etherh_priv {
 	void __iomem	*dma_base;
 	unsigned int	id;
 	void __iomem	*ctrl_port;
+	void __iomem	*base;
 	unsigned char	ctrl;
 	u32		supported;
 };
@@ -177,7 +178,7 @@ etherh_setif(struct net_device *dev)
 	switch (etherh_priv(dev)->id) {
 	case PROD_I3_ETHERLAN600:
 	case PROD_I3_ETHERLAN600A:
-		addr = (void *)dev->base_addr + EN0_RCNTHI;
+		addr = etherh_priv(dev)->base + EN0_RCNTHI;
 
 		switch (dev->if_port) {
 		case IF_PORT_10BASE2:
@@ -218,7 +219,7 @@ etherh_getifstat(struct net_device *dev)
 	switch (etherh_priv(dev)->id) {
 	case PROD_I3_ETHERLAN600:
 	case PROD_I3_ETHERLAN600A:
-		addr = (void *)dev->base_addr + EN0_RCNTHI;
+		addr = etherh_priv(dev)->base + EN0_RCNTHI;
 		switch (dev->if_port) {
 		case IF_PORT_10BASE2:
 			stat = 1;
@@ -281,7 +282,7 @@ static void
 etherh_reset(struct net_device *dev)
 {
 	struct ei_device *ei_local = netdev_priv(dev);
-	void __iomem *addr = (void *)dev->base_addr;
+	void __iomem *addr = etherh_priv(dev)->base;
 
 	writeb(E8390_NODMA+E8390_PAGE0+E8390_STOP, addr);
 
@@ -327,7 +328,7 @@ etherh_block_output (struct net_device *dev, int count, const unsigned char *buf
 
 	ei_local->dmaing = 1;
 
-	addr = (void *)dev->base_addr;
+	addr = etherh_priv(dev)->base;
 	dma_base = etherh_priv(dev)->dma_base;
 
 	count = (count + 1) & ~1;
@@ -387,7 +388,7 @@ etherh_block_input (struct net_device *dev, int count, struct sk_buff *skb, int
 
 	ei_local->dmaing = 1;
 
-	addr = (void *)dev->base_addr;
+	addr = etherh_priv(dev)->base;
 	dma_base = etherh_priv(dev)->dma_base;
 
 	buf = skb->data;
@@ -427,7 +428,7 @@ etherh_get_header (struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_p
 
 	ei_local->dmaing = 1;
 
-	addr = (void *)dev->base_addr;
+	addr = etherh_priv(dev)->base;
 	dma_base = etherh_priv(dev)->dma_base;
 
 	writeb (E8390_NODMA | E8390_PAGE0 | E8390_START, addr + E8390_CMD);
@@ -696,7 +697,8 @@ etherh_probe(struct expansion_card *ec, const struct ecard_id *id)
 		eh->ctrl_port = eh->ioc_fast;
 	}
 
-	dev->base_addr = (unsigned long)eh->memc + data->ns8390_offset;
+	eh->base = eh->memc + data->ns8390_offset;
+	dev->base_addr = (unsigned long)eh->base;
 	eh->dma_base = eh->memc + data->dataport_offset;
 	eh->ctrl_port += data->ctrlport_offset;
 

drivers/net/au1000_eth.c

@@ -1681,10 +1681,6 @@ static int au1000_init(struct net_device *dev)
 		control |= MAC_FULL_DUPLEX;
 	}
 
-	/* fix for startup without cable */
-	if (!link) 
-		dev->flags &= ~IFF_RUNNING;
-
 	aup->mac->control = control;
 	aup->mac->vlan1_tag = 0x8100; /* activate vlan support */
 	au_sync();
@@ -1709,16 +1705,14 @@ static void au1000_timer(unsigned long data)
 	if_port = dev->if_port;
 	if (aup->phy_ops->phy_status(dev, aup->phy_addr, &link, &speed) == 0) {
 		if (link) {
-			if (!(dev->flags & IFF_RUNNING)) {
+			if (!netif_carrier_ok(dev)) {
 				netif_carrier_on(dev);
-				dev->flags |= IFF_RUNNING;
 				printk(KERN_INFO "%s: link up\n", dev->name);
 			}
 		}
 		else {
-			if (dev->flags & IFF_RUNNING) {
+			if (netif_carrier_ok(dev)) {
 				netif_carrier_off(dev);
-				dev->flags &= ~IFF_RUNNING;
 				dev->if_port = 0;
 				printk(KERN_INFO "%s: link down\n", dev->name);
 			}

drivers/net/bmac.c

@@ -1412,7 +1412,6 @@ static int bmac_open(struct net_device *dev)
 	bp->opened = 1;
 	bmac_reset_and_enable(dev);
 	enable_irq(dev->irq);
-	dev->flags |= IFF_RUNNING;
 	return 0;
 }
 
@@ -1425,7 +1424,6 @@ static int bmac_close(struct net_device *dev)
 	int i;
 
 	bp->sleeping = 1;
-	dev->flags &= ~(IFF_UP | IFF_RUNNING);
 
 	/* disable rx and tx */
 	config = bmread(dev, RXCFG);

drivers/net/dm9000.h

+/*
+ * dm9000 Ethernet
+ */
+
+#ifndef _DM9000X_H_
+#define _DM9000X_H_
+
+#define DM9000_ID		0x90000A46
+
+/* although the registers are 16 bit, they are 32-bit aligned.
+ */
+
+#define DM9000_NCR             0x00
+#define DM9000_NSR             0x01
+#define DM9000_TCR             0x02
+#define DM9000_TSR1            0x03
+#define DM9000_TSR2            0x04
+#define DM9000_RCR             0x05
+#define DM9000_RSR             0x06
+#define DM9000_ROCR            0x07
+#define DM9000_BPTR            0x08
+#define DM9000_FCTR            0x09
+#define DM9000_FCR             0x0A
+#define DM9000_EPCR            0x0B
+#define DM9000_EPAR            0x0C
+#define DM9000_EPDRL           0x0D
+#define DM9000_EPDRH           0x0E
+#define DM9000_WCR             0x0F
+
+#define DM9000_PAR             0x10
+#define DM9000_MAR             0x16
+
+#define DM9000_GPCR	       0x1e
+#define DM9000_GPR             0x1f
+#define DM9000_TRPAL           0x22
+#define DM9000_TRPAH           0x23
+#define DM9000_RWPAL           0x24
+#define DM9000_RWPAH           0x25
+
+#define DM9000_VIDL            0x28
+#define DM9000_VIDH            0x29
+#define DM9000_PIDL            0x2A
+#define DM9000_PIDH            0x2B
+
+#define DM9000_CHIPR           0x2C
+#define DM9000_SMCR            0x2F
+
+#define DM9000_MRCMDX          0xF0
+#define DM9000_MRCMD           0xF2
+#define DM9000_MRRL            0xF4
+#define DM9000_MRRH            0xF5
+#define DM9000_MWCMDX          0xF6
+#define DM9000_MWCMD           0xF8
+#define DM9000_MWRL            0xFA
+#define DM9000_MWRH            0xFB
+#define DM9000_TXPLL           0xFC
+#define DM9000_TXPLH           0xFD
+#define DM9000_ISR             0xFE
+#define DM9000_IMR             0xFF
+
+#define NCR_EXT_PHY         (1<<7)
+#define NCR_WAKEEN          (1<<6)
+#define NCR_FCOL            (1<<4)
+#define NCR_FDX             (1<<3)
+#define NCR_LBK             (3<<1)
+#define NCR_RST	            (1<<0)
+
+#define NSR_SPEED           (1<<7)
+#define NSR_LINKST          (1<<6)
+#define NSR_WAKEST          (1<<5)
+#define NSR_TX2END          (1<<3)
+#define NSR_TX1END          (1<<2)
+#define NSR_RXOV            (1<<1)
+
+#define TCR_TJDIS           (1<<6)
+#define TCR_EXCECM          (1<<5)
+#define TCR_PAD_DIS2        (1<<4)
+#define TCR_CRC_DIS2        (1<<3)
+#define TCR_PAD_DIS1        (1<<2)
+#define TCR_CRC_DIS1        (1<<1)
+#define TCR_TXREQ           (1<<0)
+
+#define TSR_TJTO            (1<<7)
+#define TSR_LC              (1<<6)
+#define TSR_NC              (1<<5)
+#define TSR_LCOL            (1<<4)
+#define TSR_COL             (1<<3)
+#define TSR_EC              (1<<2)
+
+#define RCR_WTDIS           (1<<6)
+#define RCR_DIS_LONG        (1<<5)
+#define RCR_DIS_CRC         (1<<4)
+#define RCR_ALL	            (1<<3)
+#define RCR_RUNT            (1<<2)
+#define RCR_PRMSC           (1<<1)
+#define RCR_RXEN            (1<<0)
+
+#define RSR_RF              (1<<7)
+#define RSR_MF              (1<<6)
+#define RSR_LCS             (1<<5)
+#define RSR_RWTO            (1<<4)
+#define RSR_PLE             (1<<3)
+#define RSR_AE              (1<<2)
+#define RSR_CE              (1<<1)
+#define RSR_FOE             (1<<0)
+
+#define FCTR_HWOT(ot)	(( ot & 0xf ) << 4 )
+#define FCTR_LWOT(ot)	( ot & 0xf )
+
+#define IMR_PAR             (1<<7)
+#define IMR_ROOM            (1<<3)
+#define IMR_ROM             (1<<2)
+#define IMR_PTM             (1<<1)
+#define IMR_PRM             (1<<0)
+
+#define ISR_ROOS            (1<<3)
+#define ISR_ROS             (1<<2)
+#define ISR_PTS             (1<<1)
+#define ISR_PRS             (1<<0)
+#define ISR_CLR_STATUS      (ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS)
+
+#define EPCR_REEP           (1<<5)
+#define EPCR_WEP            (1<<4)
+#define EPCR_EPOS           (1<<3)
+#define EPCR_ERPRR          (1<<2)
+#define EPCR_ERPRW          (1<<1)
+#define EPCR_ERRE           (1<<0)
+
+#define GPCR_GEP_CNTL       (1<<0)
+
+#define DM9000_PKT_RDY		0x01	/* Packet ready to receive */
+#define DM9000_PKT_MAX		1536	/* Received packet max size */
+
+#endif /* _DM9000X_H_ */
+

drivers/net/pcmcia/pcnet_cs.c

@@ -1537,20 +1537,20 @@ static void shmem_get_8390_hdr(struct net_device *dev,
 static void shmem_block_input(struct net_device *dev, int count,
 			      struct sk_buff *skb, int ring_offset)
 {
-    void __iomem *xfer_start = ei_status.mem + (TX_PAGES<<8)
-				+ ring_offset
+    void __iomem *base = ei_status.mem;
+    unsigned long offset = (TX_PAGES<<8) + ring_offset
 				- (ei_status.rx_start_page << 8);
     char *buf = skb->data;
     
-    if (xfer_start + count > (void __iomem *)ei_status.rmem_end) {
+    if (offset + count > ei_status.priv) {
 	/* We must wrap the input move. */
-	int semi_count = (void __iomem *)ei_status.rmem_end - xfer_start;
-	copyin(buf, xfer_start, semi_count);
+	int semi_count = ei_status.priv - offset;
+	copyin(buf, base + offset, semi_count);
 	buf += semi_count;
-	xfer_start = ei_status.mem + (TX_PAGES<<8);
+	offset = TX_PAGES<<8;
 	count -= semi_count;
     }
-    copyin(buf, xfer_start, count);
+    copyin(buf, base + offset, count);
 }
 
 /*====================================================================*/
@@ -1611,8 +1611,9 @@ static int setup_shmem_window(dev_link_t *link, int start_pg,
     }
     
     ei_status.mem = info->base + offset;
+    ei_status.priv = req.Size;
     dev->mem_start = (u_long)ei_status.mem;
-    dev->mem_end = ei_status.rmem_end = (u_long)info->base + req.Size;
+    dev->mem_end = dev->mem_start + req.Size;
 
     ei_status.tx_start_page = start_pg;
     ei_status.rx_start_page = start_pg + TX_PAGES;

drivers/net/ppp_generic.c

@@ -1217,36 +1217,43 @@ ppp_push(struct ppp *ppp)
  */
 static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb)
 {
-	int nch, len, fragsize;
+	int len, fragsize;
 	int i, bits, hdrlen, mtu;
-	int flen, fnb;
+	int flen;
+	int navail, nfree;
+	int nbigger;
 	unsigned char *p, *q;
 	struct list_head *list;
 	struct channel *pch;
 	struct sk_buff *frag;
 	struct ppp_channel *chan;
 
-	nch = 0;
+	nfree = 0;	/* # channels which have no packet already queued */
+	navail = 0;	/* total # of usable channels (not deregistered) */
 	hdrlen = (ppp->flags & SC_MP_XSHORTSEQ)? MPHDRLEN_SSN: MPHDRLEN;
+	i = 0;
 	list = &ppp->channels;
 	while ((list = list->next) != &ppp->channels) {
 		pch = list_entry(list, struct channel, clist);
-		nch += pch->avail = (skb_queue_len(&pch->file.xq) == 0);
-		/*
-		 * If a channel hasn't had a fragment yet, it has to get
-		 * one before we send any fragments on later channels.
-		 * If it can't take a fragment now, don't give any
-		 * to subsequent channels.
-		 */
-		if (!pch->had_frag && !pch->avail) {
-			while ((list = list->next) != &ppp->channels) {
-				pch = list_entry(list, struct channel, clist);
-				pch->avail = 0;
+		navail += pch->avail = (pch->chan != NULL);
+		if (pch->avail) {
+			if (skb_queue_len(&pch->file.xq) == 0
+			    || !pch->had_frag) {
+				pch->avail = 2;
+				++nfree;
 			}
-			break;
+			if (!pch->had_frag && i < ppp->nxchan)
+				ppp->nxchan = i;
 		}
+		++i;
 	}
-	if (nch == 0)
+
+	/*
+	 * Don't start sending this packet unless at least half of
+	 * the channels are free.  This gives much better TCP
+	 * performance if we have a lot of channels.
+	 */
+	if (nfree == 0 || nfree < navail / 2)
 		return 0;	/* can't take now, leave it in xmit_pending */
 
 	/* Do protocol field compression (XXX this should be optional) */
@@ -1257,14 +1264,19 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb)
 		--len;
 	}
 
-	/* decide on fragment size */
+	/*
+	 * Decide on fragment size.
+	 * We create a fragment for each free channel regardless of
+	 * how small they are (i.e. even 0 length) in order to minimize
+	 * the time that it will take to detect when a channel drops
+	 * a fragment.
+	 */
 	fragsize = len;
-	if (nch > 1) {
-		int maxch = ROUNDUP(len, MIN_FRAG_SIZE);
-		if (nch > maxch)
-			nch = maxch;
-		fragsize = ROUNDUP(fragsize, nch);
-	}
+	if (nfree > 1)
+		fragsize = ROUNDUP(fragsize, nfree);
+	/* nbigger channels get fragsize bytes, the rest get fragsize-1,
+	   except if nbigger==0, then they all get fragsize. */
+	nbigger = len % nfree;
 
 	/* skip to the channel after the one we last used
 	   and start at that one */
@@ -1278,7 +1290,7 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb)
 
 	/* create a fragment for each channel */
 	bits = B;
-	do {
+	while (nfree > 0 || len > 0) {
 		list = list->next;
 		if (list == &ppp->channels) {
 			i = 0;
@@ -1289,61 +1301,92 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb)
 		if (!pch->avail)
 			continue;
 
+		/*
+		 * Skip this channel if it has a fragment pending already and
+		 * we haven't given a fragment to all of the free channels.
+		 */
+		if (pch->avail == 1) {
+			if (nfree > 0)
+				continue;
+		} else {
+			--nfree;
+			pch->avail = 1;
+		}
+
 		/* check the channel's mtu and whether it is still attached. */
 		spin_lock_bh(&pch->downl);
-		if (pch->chan == 0 || (mtu = pch->chan->mtu) < hdrlen) {
-			/* can't use this channel */
+		if (pch->chan == NULL) {
+			/* can't use this channel, it's being deregistered */
 			spin_unlock_bh(&pch->downl);
 			pch->avail = 0;
-			if (--nch == 0)
+			if (--navail == 0)
 				break;
 			continue;
 		}
 
 		/*
-		 * We have to create multiple fragments for this channel
-		 * if fragsize is greater than the channel's mtu.
+		 * Create a fragment for this channel of
+		 * min(max(mtu+2-hdrlen, 4), fragsize, len) bytes.
+		 * If mtu+2-hdrlen < 4, that is a ridiculously small
+		 * MTU, so we use mtu = 2 + hdrlen.
 		 */
 		if (fragsize > len)
 			fragsize = len;
-		for (flen = fragsize; flen > 0; flen -= fnb) {
-			fnb = flen;
-			if (fnb > mtu + 2 - hdrlen)
-				fnb = mtu + 2 - hdrlen;
-			if (fnb >= len)
-				bits |= E;
-			frag = alloc_skb(fnb + hdrlen, GFP_ATOMIC);
-			if (frag == 0)
-				goto noskb;
-			q = skb_put(frag, fnb + hdrlen);
-			/* make the MP header */
-			q[0] = PPP_MP >> 8;
-			q[1] = PPP_MP;
-			if (ppp->flags & SC_MP_XSHORTSEQ) {
-				q[2] = bits + ((ppp->nxseq >> 8) & 0xf);
-				q[3] = ppp->nxseq;
-			} else {
-				q[2] = bits;
-				q[3] = ppp->nxseq >> 16;
-				q[4] = ppp->nxseq >> 8;
-				q[5] = ppp->nxseq;
-			}
-
-			/* copy the data in */
-			memcpy(q + hdrlen, p, fnb);
-
-			/* try to send it down the channel */
-			chan = pch->chan;
-			if (!chan->ops->start_xmit(chan, frag))
-				skb_queue_tail(&pch->file.xq, frag);
-			pch->had_frag = 1;
-			p += fnb;
-			len -= fnb;
-			++ppp->nxseq;
-			bits = 0;
+		flen = fragsize;
+		mtu = pch->chan->mtu + 2 - hdrlen;
+		if (mtu < 4)
+			mtu = 4;
+		if (flen > mtu)
+			flen = mtu;
+		if (flen == len && nfree == 0)
+			bits |= E;
+		frag = alloc_skb(flen + hdrlen + (flen == 0), GFP_ATOMIC);
+		if (frag == 0)
+			goto noskb;
+		q = skb_put(frag, flen + hdrlen);
+
+		/* make the MP header */
+		q[0] = PPP_MP >> 8;
+		q[1] = PPP_MP;
+		if (ppp->flags & SC_MP_XSHORTSEQ) {
+			q[2] = bits + ((ppp->nxseq >> 8) & 0xf);
+			q[3] = ppp->nxseq;
+		} else {
+			q[2] = bits;
+			q[3] = ppp->nxseq >> 16;
+			q[4] = ppp->nxseq >> 8;
+			q[5] = ppp->nxseq;
 		}
+
+		/*
+		 * Copy the data in.
+		 * Unfortunately there is a bug in older versions of
+		 * the Linux PPP multilink reconstruction code where it
+		 * drops 0-length fragments.  Therefore we make sure the
+		 * fragment has at least one byte of data.  Any bytes
+		 * we add in this situation will end up as padding on the
+		 * end of the reconstructed packet.
+		 */
+		if (flen == 0)
+			*skb_put(frag, 1) = 0;
+		else
+			memcpy(q + hdrlen, p, flen);
+
+		/* try to send it down the channel */
+		chan = pch->chan;
+		if (skb_queue_len(&pch->file.xq)
+		    || !chan->ops->start_xmit(chan, frag))
+			skb_queue_tail(&pch->file.xq, frag);
+		pch->had_frag = 1;
+		p += flen;
+		len -= flen;
+		++ppp->nxseq;
+		bits = 0;
 		spin_unlock_bh(&pch->downl);
-	} while (len > 0);
+
+		if (--nbigger == 0 && fragsize > 0)
+			--fragsize;
+	}
 	ppp->nxchan = i;
 
 	return 1;
@@ -1422,7 +1465,7 @@ ppp_input(struct ppp_channel *chan, struct sk_buff *skb)
 		kfree_skb(skb);
 		return;
 	}
-	
+
 	proto = PPP_PROTO(skb);
 	read_lock_bh(&pch->upl);
 	if (pch->ppp == 0 || proto >= 0xc000 || proto == PPP_CCPFRAG) {
@@ -1691,7 +1734,7 @@ ppp_receive_mp_frame(struct ppp *ppp, struct sk_buff *skb, struct channel *pch)
 	struct list_head *l;
 	int mphdrlen = (ppp->flags & SC_MP_SHORTSEQ)? MPHDRLEN_SSN: MPHDRLEN;
 
-	if (!pskb_may_pull(skb, mphdrlen + 1) || ppp->mrru == 0)
+	if (!pskb_may_pull(skb, mphdrlen) || ppp->mrru == 0)
 		goto err;		/* no good, throw it away */
 
 	/* Decode sequence number and begin/end bits */

drivers/net/sk98lin/skge.c

@@ -4212,7 +4212,7 @@ SK_BOOL		DualNet;
 			Flags);
 
 		SkGeStopPort(pAC, IoC, FromPort, SK_STOP_ALL, SK_HARD_RST);
-		pAC->dev[Param.Para32[0]]->flags &= ~IFF_RUNNING;
+		netif_carrier_off(pAC->dev[Param.Para32[0]]);
 		spin_unlock_irqrestore(
 			&pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock,
 			Flags);
@@ -4355,7 +4355,7 @@ SK_BOOL		DualNet;
 		}
 
 		/* Inform the world that link protocol is up. */
-		pAC->dev[Param.Para32[0]]->flags |= IFF_RUNNING;
+		netif_carrier_on(pAC->dev[Param.Para32[0]]);
 
 		break;
 	case SK_DRV_NET_DOWN:	 /* SK_U32 Reason */
@@ -4368,7 +4368,7 @@ SK_BOOL		DualNet;
 		} else {
 			DoPrintInterfaceChange = SK_TRUE;
 		}
-		pAC->dev[Param.Para32[1]]->flags &= ~IFF_RUNNING;
+		netif_carrier_off(pAC->dev[Param.Para32[1]]);
 		break;
 	case SK_DRV_SWITCH_HARD: /* SK_U32 FromPortIdx SK_U32 ToPortIdx */
 		SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT,
@@ -4961,7 +4961,6 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
 #ifdef CONFIG_NET_POLL_CONTROLLER
 	dev->poll_controller =	&SkGePollController;
 #endif
-	dev->flags &= 		~IFF_RUNNING;
 	SET_NETDEV_DEV(dev, &pdev->dev);
 	SET_ETHTOOL_OPS(dev, &SkGeEthtoolOps);
 
@@ -5035,7 +5034,6 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
 		dev->set_mac_address    = &SkGeSetMacAddr;
 		dev->do_ioctl           = &SkGeIoctl;
 		dev->change_mtu         = &SkGeChangeMtu;
-		dev->flags             &= ~IFF_RUNNING;
 		SET_NETDEV_DEV(dev, &pdev->dev);
 		SET_ETHTOOL_OPS(dev, &SkGeEthtoolOps);
 

drivers/net/sk_g16.h

-/*-
- *
- * This software may be used and distributed according to the terms
- * of the GNU General Public License, incorporated herein by reference.
- *
- * Module         : sk_g16.h
- * Version        : $Revision$  
- *
- * Author         : M.Hipp (mhipp@student.uni-tuebingen.de)
- * changes by     : Patrick J.D. Weichmann
- *
- * Date Created   : 94/05/25
- *
- * Description    : In here are all necessary definitions of  
- *                  the am7990 (LANCE) chip used for writing a
- *                  network device driver which uses this chip 
- *
- * $Log$
--*/
-
-#ifndef SK_G16_H
-
-#define SK_G16_H
-
-
-/*
- * 	Control and Status Register 0 (CSR0) bit definitions
- *
- * (R=Readable) (W=Writeable) (S=Set on write) (C-Clear on write)
- *
- */
-
-#define CSR0_ERR	0x8000	/* Error summary (R) */
-#define CSR0_BABL	0x4000	/* Babble transmitter timeout error (RC) */
-#define CSR0_CERR	0x2000	/* Collision Error (RC) */
-#define CSR0_MISS	0x1000	/* Missed packet (RC) */
-#define CSR0_MERR	0x0800	/* Memory Error  (RC) */ 
-#define CSR0_RINT	0x0400	/* Receiver Interrupt (RC) */
-#define CSR0_TINT       0x0200	/* Transmit Interrupt (RC) */ 
-#define CSR0_IDON	0x0100	/* Initialization Done (RC) */
-#define CSR0_INTR	0x0080	/* Interrupt Flag (R) */
-#define CSR0_INEA	0x0040	/* Interrupt Enable (RW) */
-#define CSR0_RXON	0x0020	/* Receiver on (R) */
-#define CSR0_TXON	0x0010  /* Transmitter on (R) */
-#define CSR0_TDMD	0x0008	/* Transmit Demand (RS) */
-#define CSR0_STOP	0x0004 	/* Stop (RS) */
-#define CSR0_STRT	0x0002	/* Start (RS) */
-#define CSR0_INIT	0x0001	/* Initialize (RS) */
-
-#define CSR0_CLRALL     0x7f00  /* mask for all clearable bits */
-
-/*
- *    Control and Status Register 3 (CSR3) bit definitions
- *
- */
-
-#define CSR3_BSWAP	0x0004	/* Byte Swap (RW) */
-#define CSR3_ACON	0x0002  /* ALE Control (RW) */
-#define CSR3_BCON	0x0001	/* Byte Control (RW) */
-
-/*
- *	Initialization Block Mode operation Bit Definitions.
- */
-
-#define MODE_PROM	0x8000	/* Promiscuous Mode */
-#define MODE_INTL	0x0040  /* Internal Loopback */
-#define MODE_DRTY	0x0020  /* Disable Retry */ 
-#define MODE_COLL	0x0010	/* Force Collision */
-#define MODE_DTCR	0x0008	/* Disable Transmit CRC) */
-#define MODE_LOOP	0x0004	/* Loopback */
-#define MODE_DTX	0x0002	/* Disable the Transmitter */ 
-#define MODE_DRX	0x0001  /* Disable the Receiver */
-
-#define MODE_NORMAL 	0x0000  /* Normal operation mode */
-
-/*
- * 	Receive message descriptor status bit definitions.
- */
-
-#define RX_OWN		0x80	/* Owner bit 0 = host, 1 = lance */
-#define RX_ERR		0x40	/* Error Summary */
-#define RX_FRAM		0x20	/* Framing Error */
-#define RX_OFLO		0x10	/* Overflow Error */
-#define RX_CRC		0x08	/* CRC Error */ 
-#define RX_BUFF		0x04	/* Buffer Error */
-#define RX_STP		0x02	/* Start of Packet */
-#define RX_ENP		0x01	/* End of Packet */
-
-
-/*
- *	Transmit message descriptor status bit definitions.
- */
-
-#define TX_OWN		0x80	/* Owner bit 0 = host, 1 = lance */
-#define TX_ERR		0x40    /* Error Summary */
-#define TX_MORE		0x10	/* More the 1 retry needed to Xmit */
-#define TX_ONE		0x08	/* One retry needed to Xmit */
-#define TX_DEF		0x04	/* Deferred */
-#define TX_STP 		0x02	/* Start of Packet */
-#define TX_ENP		0x01	/* End of Packet */
-
-/*
- *      Transmit status (2) (valid if TX_ERR == 1)
- */
-
-#define TX_BUFF 	0x8000  /* Buffering error (no ENP) */
-#define TX_UFLO 	0x4000  /* Underflow (late memory) */
-#define TX_LCOL 	0x1000  /* Late collision */
-#define TX_LCAR 	0x0400  /* Loss of Carrier */
-#define TX_RTRY 	0x0200  /* Failed after 16 retransmissions  */
-#define TX_TDR          0x003f  /* Time-domain-reflectometer-value */
-
-
-/* 
- * Structures used for Communication with the LANCE 
- */
-
-/* LANCE Initialize Block */
-
-struct init_block 
-{
-  unsigned short mode;     /* Mode Register */
-  unsigned char  paddr[6]; /* Physical Address (MAC) */
-  unsigned char  laddr[8]; /* Logical Filter Address (not used) */
-  unsigned int   rdrp;     /* Receive Descriptor Ring pointer */
-  unsigned int   tdrp;     /* Transmit Descriptor Ring pointer */
-};
-
-
-/* Receive Message Descriptor Entry */
-
-struct rmd 
-{ 
-  union
-  {
-    unsigned long buffer;     /* Address of buffer */
-    struct 
-    {
-      unsigned char unused[3]; 
-      unsigned volatile char status;   /* Status Bits */
-    } s;
-  } u;
-  volatile short blen;        /* Buffer Length (two's complement) */
-  unsigned short mlen;        /* Message Byte Count */
-};
-
-
-/* Transmit Message Descriptor Entry */
-
-struct tmd   
-{
-  union 
-  {
-    unsigned long  buffer;    /* Address of buffer */
-    struct 
-    {
-      unsigned char unused[3];
-      unsigned volatile char status;   /* Status Bits */
-    } s;
-  } u;
-  unsigned short blen;             /* Buffer Length (two's complement) */
-  unsigned volatile short status2; /* Error Status Bits */
-};
-
-#endif /* End of SK_G16_H */

drivers/net/smc91x.c

@@ -129,7 +129,7 @@ MODULE_PARM_DESC(nowait, "set to 1 for no wait state");
 /*
  * Transmit timeout, default 5 seconds.
  */
-static int watchdog = 5000;
+static int watchdog = 1000;
 module_param(watchdog, int, 0400);
 MODULE_PARM_DESC(watchdog, "transmit timeout in milliseconds");
 
@@ -660,15 +660,14 @@ static void smc_hardware_send_pkt(unsigned long data)
 	SMC_outw(((len & 1) ? (0x2000 | buf[len-1]) : 0), ioaddr, DATA_REG);
 
 	/*
-	 * If THROTTLE_TX_PKTS is set, we look at the TX_EMPTY flag
-	 * before queueing this packet for TX, and if it's clear then
-	 * we stop the queue here.  This will have the effect of
-	 * having at most 2 packets queued for TX in the chip's memory
-	 * at all time. If THROTTLE_TX_PKTS is not set then the queue
-	 * is stopped only when memory allocation (MC_ALLOC) does not
-	 * succeed right away.
+	 * If THROTTLE_TX_PKTS is set, we stop the queue here. This will
+	 * have the effect of having at most one packet queued for TX
+	 * in the chip's memory at all time.
+	 *
+	 * If THROTTLE_TX_PKTS is not set then the queue is stopped only
+	 * when memory allocation (MC_ALLOC) does not succeed right away.
 	 */
-	if (THROTTLE_TX_PKTS && !(SMC_GET_INT() & IM_TX_EMPTY_INT))
+	if (THROTTLE_TX_PKTS)
 		netif_stop_queue(dev);
 
 	/* queue the packet for TX */
@@ -792,17 +791,20 @@ static void smc_tx(struct net_device *dev)
 	DBG(2, "%s: TX STATUS 0x%04x PNR 0x%02x\n",
 		dev->name, tx_status, packet_no);
 
-	if (!(tx_status & TS_SUCCESS))
+	if (!(tx_status & ES_TX_SUC))
 		lp->stats.tx_errors++;
-	if (tx_status & TS_LOSTCAR)
+
+	if (tx_status & ES_LOSTCARR)
 		lp->stats.tx_carrier_errors++;
 
-	if (tx_status & TS_LATCOL) {
-		PRINTK("%s: late collision occurred on last xmit\n", dev->name);
+	if (tx_status & (ES_LATCOL | ES_16COL)) {
+		PRINTK("%s: %s occurred on last xmit\n", dev->name,
+		       (tx_status & ES_LATCOL) ?
+			"late collision" : "too many collisions");
 		lp->stats.tx_window_errors++;
 		if (!(lp->stats.tx_window_errors & 63) && net_ratelimit()) {
-			printk(KERN_INFO "%s: unexpectedly large numbers of "
-			       "late collisions. Please check duplex "
+			printk(KERN_INFO "%s: unexpectedly large number of "
+			       "bad collisions. Please check duplex "
 			       "setting.\n", dev->name);
 		}
 	}
@@ -1236,7 +1238,7 @@ static void smc_10bt_check_media(struct net_device *dev, int init)
 	old_carrier = netif_carrier_ok(dev) ? 1 : 0;
 
 	SMC_SELECT_BANK(0);
-	new_carrier = SMC_inw(ioaddr, EPH_STATUS_REG) & ES_LINK_OK ? 1 : 0;
+	new_carrier = (SMC_GET_EPH_STATUS() & ES_LINK_OK) ? 1 : 0;
 	SMC_SELECT_BANK(2);
 
 	if (init || (old_carrier != new_carrier)) {
@@ -1308,15 +1310,16 @@ static irqreturn_t smc_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 		if (!status)
 			break;
 
-		if (status & IM_RCV_INT) {
-			DBG(3, "%s: RX irq\n", dev->name);
-			smc_rcv(dev);
-		} else if (status & IM_TX_INT) {
+		if (status & IM_TX_INT) {
+			/* do this before RX as it will free memory quickly */
 			DBG(3, "%s: TX int\n", dev->name);
 			smc_tx(dev);
 			SMC_ACK_INT(IM_TX_INT);
 			if (THROTTLE_TX_PKTS)
 				netif_wake_queue(dev);
+		} else if (status & IM_RCV_INT) {
+			DBG(3, "%s: RX irq\n", dev->name);
+			smc_rcv(dev);
 		} else if (status & IM_ALLOC_INT) {
 			DBG(3, "%s: Allocation irq\n", dev->name);
 			tasklet_hi_schedule(&lp->tx_task);
@@ -1337,7 +1340,10 @@ static irqreturn_t smc_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 			/* multiple collisions */
 			lp->stats.collisions += card_stats & 0xF;
 		} else if (status & IM_RX_OVRN_INT) {
-			DBG(1, "%s: RX overrun\n", dev->name);
+			DBG(1, "%s: RX overrun (EPH_ST 0x%04x)\n", dev->name,
+			       ({ int eph_st; SMC_SELECT_BANK(0);
+				  eph_st = SMC_GET_EPH_STATUS();
+				  SMC_SELECT_BANK(2); eph_st; }) );
 			SMC_ACK_INT(IM_RX_OVRN_INT);
 			lp->stats.rx_errors++;
 			lp->stats.rx_fifo_errors++;
@@ -1389,7 +1395,7 @@ static void smc_timeout(struct net_device *dev)
 {
 	struct smc_local *lp = netdev_priv(dev);
 	void __iomem *ioaddr = lp->base;
-	int status, mask, meminfo, fifo;
+	int status, mask, eph_st, meminfo, fifo;
 
 	DBG(2, "%s: %s\n", dev->name, __FUNCTION__);
 
@@ -1398,11 +1404,13 @@ static void smc_timeout(struct net_device *dev)
 	mask = SMC_GET_INT_MASK();
 	fifo = SMC_GET_FIFO();
 	SMC_SELECT_BANK(0);
+	eph_st = SMC_GET_EPH_STATUS();
 	meminfo = SMC_GET_MIR();
 	SMC_SELECT_BANK(2);
 	spin_unlock_irq(&lp->lock);
-	PRINTK( "%s: INT 0x%02x MASK 0x%02x MEM 0x%04x FIFO 0x%04x\n",
-		dev->name, status, mask, meminfo, fifo );
+	PRINTK( "%s: TX timeout (INT 0x%02x INTMASK 0x%02x "
+		"MEM 0x%04x FIFO 0x%04x EPH_ST 0x%04x)\n",
+		dev->name, status, mask, meminfo, fifo, eph_st );
 
 	smc_reset(dev);
 	smc_enable(dev);
@@ -1863,7 +1871,7 @@ static int __init smc_probe(struct net_device *dev, void __iomem *ioaddr)
 	SMC_SELECT_BANK(1);
 	val = SMC_GET_BASE();
 	val = ((val & 0x1F00) >> 3) << SMC_IO_SHIFT;
-	if (((unsigned long)ioaddr & ((PAGE_SIZE-1)<<SMC_IO_SHIFT)) != val) { /*XXX: WTF? */
+	if (((unsigned int)ioaddr & (0x3e0 << SMC_IO_SHIFT)) != val) {
 		printk("%s: IOADDR %p doesn't match configuration (%x).\n",
 			CARDNAME, ioaddr, val);
 	}

drivers/net/smc91x.h

@@ -151,7 +151,7 @@
 
 /* We actually can't write halfwords properly if not word aligned */
 static inline void
-SMC_outw(u16 val, unsigned long ioaddr, int reg)
+SMC_outw(u16 val, void __iomem *ioaddr, int reg)
 {
 	if (reg & 2) {
 		unsigned int v = val << 16;
@@ -317,7 +317,7 @@ static inline void SMC_outsw (unsigned long a, int r, unsigned char* p, int l)
 #define SMC_insl(a, r, p, l) \
 	smc_pxa_dma_insl(a, lp->physaddr, r, dev->dma, p, l)
 static inline void
-smc_pxa_dma_insl(u_long ioaddr, u_long physaddr, int reg, int dma,
+smc_pxa_dma_insl(void __iomem *ioaddr, u_long physaddr, int reg, int dma,
 		 u_char *buf, int len)
 {
 	dma_addr_t dmabuf;
@@ -355,7 +355,7 @@ smc_pxa_dma_insl(u_long ioaddr, u_long physaddr, int reg, int dma,
 #define SMC_insw(a, r, p, l) \
 	smc_pxa_dma_insw(a, lp->physaddr, r, dev->dma, p, l)
 static inline void
-smc_pxa_dma_insw(u_long ioaddr, u_long physaddr, int reg, int dma,
+smc_pxa_dma_insw(void __iomem *ioaddr, u_long physaddr, int reg, int dma,
 		 u_char *buf, int len)
 {
 	dma_addr_t dmabuf;
@@ -680,14 +680,6 @@ static const char * chip_ids[ 16 ] =  {
 	NULL, NULL, NULL};
 
 
-/*
- . Transmit status bits
-*/
-#define TS_SUCCESS 0x0001
-#define TS_LOSTCAR 0x0400
-#define TS_LATCOL  0x0200
-#define TS_16COL   0x0010
-
 /*
  . Receive status bits
 */
@@ -845,6 +837,7 @@ static const char * chip_ids[ 16 ] =  {
 #define SMC_GET_FIFO()		SMC_inw( ioaddr, FIFO_REG )
 #define SMC_GET_PTR()		SMC_inw( ioaddr, PTR_REG )
 #define SMC_SET_PTR(x)		SMC_outw( x, ioaddr, PTR_REG )
+#define SMC_GET_EPH_STATUS()	SMC_inw( ioaddr, EPH_STATUS_REG )
 #define SMC_GET_RCR()		SMC_inw( ioaddr, RCR_REG )
 #define SMC_SET_RCR(x)		SMC_outw( x, ioaddr, RCR_REG )
 #define SMC_GET_REV()		SMC_inw( ioaddr, REV_REG )

drivers/net/tlan.c

@@ -2819,7 +2819,7 @@ void TLan_PhyMonitor( struct net_device *dev )
  	       if (priv->link) {
 		      priv->link = 0;
 	              printk(KERN_DEBUG "TLAN: %s has lost link\n", dev->name);
-	              dev->flags &= ~IFF_RUNNING;
+		      netif_carrier_off(dev);
 		      TLan_SetTimer( dev, (2*HZ), TLAN_TIMER_LINK_BEAT );
 		      return;
 		}
@@ -2829,7 +2829,7 @@ void TLan_PhyMonitor( struct net_device *dev )
         if ((phy_status & MII_GS_LINK) && !priv->link) {
  		priv->link = 1;
         	printk(KERN_DEBUG "TLAN: %s has reestablished link\n", dev->name);
-        	dev->flags |= IFF_RUNNING;
+		netif_carrier_on(dev);
         }
 
 	/* Setup a new monitor */

drivers/net/tokenring/ibmtr.c

@@ -888,11 +888,6 @@ static int tok_open(struct net_device *dev)
 	ti->sap_status   = CLOSED; /* CLOSED or OPEN      */
 	ti->open_failure =     NO; /* NO     or YES       */
 	ti->open_mode    = MANUAL; /* MANUAL or AUTOMATIC */
-	/* 12/2000 not typical Linux, but we can use RUNNING to let us know when
-	the network has crapped out or cables are disconnected. Useful because
-	the IFF_UP flag stays up the whole time, until ifconfig tr0 down.
-	*/
-	dev->flags &= ~IFF_RUNNING;
 
 	ti->sram_phys &= ~1; /* to reverse what we do in tok_close */
 	/* init the spinlock */
@@ -1242,7 +1237,7 @@ irqreturn_t tok_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 		ti->open_status = CLOSED;
 		ti->sap_status  = CLOSED;
 		ti->open_mode   = AUTOMATIC;
-		dev->flags &= ~IFF_RUNNING;
+		netif_carrier_off(dev);
 		netif_stop_queue(dev);
 		ti->open_action = RESTART;
 		outb(0, dev->base_addr + ADAPTRESET);
@@ -1323,7 +1318,7 @@ irqreturn_t tok_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 				break;
 			}
 			netif_wake_queue(dev);
-			dev->flags |= IFF_RUNNING;/*BMS 12/2000*/
+			netif_carrier_on(dev);
 			break;
 		case DIR_INTERRUPT:
 		case DIR_MOD_OPEN_PARAMS:
@@ -1427,7 +1422,7 @@ irqreturn_t tok_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 								ring_status);
 			if(ring_status& (REMOVE_RECV|AUTO_REMOVAL|LOBE_FAULT)){
 				netif_stop_queue(dev);
-				dev->flags &= ~IFF_RUNNING;/*not typical Linux*/
+				netif_carrier_off(dev);
 				DPRINTK("Remove received, or Auto-removal error"
 					", or Lobe fault\n");
 				DPRINTK("We'll try to reopen the closed adapter"

drivers/net/wan/hdlc_generic.c

 /*
  * Generic HDLC support routines for Linux
  *
- * Copyright (C) 1999 - 2003 Krzysztof Halasa <khc@pm.waw.pl>
+ * Copyright (C) 1999 - 2005 Krzysztof Halasa <khc@pm.waw.pl>
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of version 2 of the GNU General Public License
@@ -38,7 +38,7 @@
 #include <linux/hdlc.h>
 
 
-static const char* version = "HDLC support module revision 1.17";
+static const char* version = "HDLC support module revision 1.18";
 
 #undef DEBUG_LINK
 
@@ -126,10 +126,13 @@ void hdlc_set_carrier(int on, struct net_device *dev)
 	if (!hdlc->open)
 		goto carrier_exit;
 
-	if (hdlc->carrier)
+	if (hdlc->carrier) {
+		printk(KERN_INFO "%s: Carrier detected\n", dev->name);
 		__hdlc_set_carrier_on(dev);
-	else
+	} else {
+		printk(KERN_INFO "%s: Carrier lost\n", dev->name);
 		__hdlc_set_carrier_off(dev);
+	}
 
 carrier_exit:
 	spin_unlock_irqrestore(&hdlc->state_lock, flags);
@@ -157,8 +160,11 @@ int hdlc_open(struct net_device *dev)
 
 	spin_lock_irq(&hdlc->state_lock);
 
-	if (hdlc->carrier)
+	if (hdlc->carrier) {
+		printk(KERN_INFO "%s: Carrier detected\n", dev->name);
 		__hdlc_set_carrier_on(dev);
+	} else
+		printk(KERN_INFO "%s: No carrier\n", dev->name);
 
 	hdlc->open = 1;
 

drivers/net/wan/lmc/lmc_main.c

@@ -723,7 +723,7 @@ static void lmc_watchdog (unsigned long data) /*fold00*/
         /* lmc_reset (sc); Why reset??? The link can go down ok */
 
         /* Inform the world that link has been lost */
-        dev->flags &= ~IFF_RUNNING;
+	netif_carrier_off(dev);
     }
 
     /*
@@ -736,7 +736,7 @@ static void lmc_watchdog (unsigned long data) /*fold00*/
          /* lmc_reset (sc); Again why reset??? */
 
          /* Inform the world that link protocol is back up. */
-         dev->flags |= IFF_RUNNING;
+	 netif_carrier_on(dev);
 
          /* Now we have to tell the syncppp that we had an outage
           * and that it should deal.  Calling sppp_reopen here
@@ -1168,8 +1168,6 @@ static void lmc_running_reset (struct net_device *dev) /*fold00*/
     sc->lmc_media->set_link_status (sc, 1);
     sc->lmc_media->set_status (sc, NULL);
 
-    //dev->flags |= IFF_RUNNING;
-    
     netif_wake_queue(dev);
 
     sc->lmc_txfull = 0;
@@ -1233,8 +1231,6 @@ static int lmc_ifdown (struct net_device *dev) /*fold00*/
     csr6 &= ~LMC_DEC_SR;		/* Turn off the Receive bit */
     LMC_CSR_WRITE (sc, csr_command, csr6);
 
-    dev->flags &= ~IFF_RUNNING;
-
     sc->stats.rx_missed_errors +=
         LMC_CSR_READ (sc, csr_missed_frames) & 0xffff;
 

drivers/net/wireless/orinoco.h

@@ -119,7 +119,6 @@ extern struct net_device *alloc_orinocodev(int sizeof_card,
 extern void free_orinocodev(struct net_device *dev);
 extern int __orinoco_up(struct net_device *dev);
 extern int __orinoco_down(struct net_device *dev);
-extern int orinoco_stop(struct net_device *dev);
 extern int orinoco_reinit_firmware(struct net_device *dev);
 extern irqreturn_t orinoco_interrupt(int irq, void * dev_id, struct pt_regs *regs);
 

include/linux/dm9000.h

+/* include/linux/dm9000.h
+ *
+ * Copyright (c) 2004 Simtec Electronics
+ *   Ben Dooks <ben@simtec.co.uk>
+ *
+ * Header file for dm9000 platform data
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#ifndef __DM9000_PLATFORM_DATA
+#define __DM9000_PLATFORM_DATA __FILE__
+
+/* IO control flags */
+
+#define DM9000_PLATF_8BITONLY	(0x0001)
+#define DM9000_PLATF_16BITONLY	(0x0002)
+#define DM9000_PLATF_32BITONLY	(0x0004)
+
+/* platfrom data for platfrom device structure's platfrom_data field */
+
+struct dm9000_plat_data {
+	unsigned int	flags;
+
+	/* allow replacement IO routines */
+
+	void	(*inblk)(void __iomem *reg, void *data, int len);
+	void	(*outblk)(void __iomem *reg, void *data, int len);
+	void	(*dumpblk)(void __iomem *reg, int len);
+};
+
+#endif /* __DM9000_PLATFORM_DATA */
+

include/linux/hdlc.h

 /*
  * Generic HDLC support routines for Linux
  *
- * Copyright (C) 1999-2003 Krzysztof Halasa <khc@pm.waw.pl>
+ * Copyright (C) 1999-2005 Krzysztof Halasa <khc@pm.waw.pl>
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of version 2 of the GNU General Public License
@@ -41,6 +41,7 @@
 #define LMI_NONE		1 /* No LMI, all PVCs are static */
 #define LMI_ANSI		2 /* ANSI Annex D */
 #define LMI_CCITT		3 /* ITU-T Annex A */
+#define LMI_CISCO		4 /* The "original" LMI, aka Gang of Four */
 
 #define HDLC_MAX_MTU 1500	/* Ethernet 1500 bytes */
 #define HDLC_MAX_MRU (HDLC_MAX_MTU + 10 + 14 + 4) /* for ETH+VLAN over FR */
@@ -89,6 +90,7 @@ typedef struct pvc_device_struct {
 		unsigned int deleted: 1;
 		unsigned int fecn: 1;
 		unsigned int becn: 1;
+		unsigned int bandwidth;	/* Cisco LMI reporting only */
 	}state;
 }pvc_device;
 

include/linux/if.h

@@ -33,7 +33,7 @@
 #define	IFF_LOOPBACK	0x8		/* is a loopback net		*/
 #define	IFF_POINTOPOINT	0x10		/* interface is has p-p link	*/
 #define	IFF_NOTRAILERS	0x20		/* avoid use of trailers	*/
-#define	IFF_RUNNING	0x40		/* resources allocated		*/
+#define	IFF_RUNNING	0x40		/* interface running and carrier ok */
 #define	IFF_NOARP	0x80		/* no ARP protocol		*/
 #define	IFF_PROMISC	0x100		/* receive all packets		*/
 #define	IFF_ALLMULTI	0x200		/* receive all multicast packets*/

net/core/wireless.c

@@ -2,7 +2,7 @@
  * This file implement the Wireless Extensions APIs.
  *
  * Authors :	Jean Tourrilhes - HPL - <jt@hpl.hp.com>
- * Copyright (c) 1997-2004 Jean Tourrilhes, All Rights Reserved.
+ * Copyright (c) 1997-2005 Jean Tourrilhes, All Rights Reserved.
  *
  * (As all part of the Linux kernel, this file is GPL)
  */
@@ -187,6 +187,12 @@ static const struct iw_ioctl_description standard_ioctl[] = {
 		.header_type	= IW_HEADER_TYPE_ADDR,
 		.flags		= IW_DESCR_FLAG_DUMP,
 	},
+	[SIOCSIWMLME	- SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.min_tokens	= sizeof(struct iw_mlme),
+		.max_tokens	= sizeof(struct iw_mlme),
+	},
 	[SIOCGIWAPLIST	- SIOCIWFIRST] = {
 		.header_type	= IW_HEADER_TYPE_POINT,
 		.token_size	= sizeof(struct sockaddr) +
@@ -195,7 +201,10 @@ static const struct iw_ioctl_description standard_ioctl[] = {
 		.flags		= IW_DESCR_FLAG_NOMAX,
 	},
 	[SIOCSIWSCAN	- SIOCIWFIRST] = {
-		.header_type	= IW_HEADER_TYPE_PARAM,
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.min_tokens	= 0,
+		.max_tokens	= sizeof(struct iw_scan_req),
 	},
 	[SIOCGIWSCAN	- SIOCIWFIRST] = {
 		.header_type	= IW_HEADER_TYPE_POINT,
@@ -273,6 +282,42 @@ static const struct iw_ioctl_description standard_ioctl[] = {
 	[SIOCGIWPOWER	- SIOCIWFIRST] = {
 		.header_type	= IW_HEADER_TYPE_PARAM,
 	},
+	[SIOCSIWGENIE	- SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.max_tokens	= IW_GENERIC_IE_MAX,
+	},
+	[SIOCGIWGENIE	- SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.max_tokens	= IW_GENERIC_IE_MAX,
+	},
+	[SIOCSIWAUTH	- SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_PARAM,
+	},
+	[SIOCGIWAUTH	- SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_PARAM,
+	},
+	[SIOCSIWENCODEEXT - SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.min_tokens	= sizeof(struct iw_encode_ext),
+		.max_tokens	= sizeof(struct iw_encode_ext) +
+				  IW_ENCODING_TOKEN_MAX,
+	},
+	[SIOCGIWENCODEEXT - SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.min_tokens	= sizeof(struct iw_encode_ext),
+		.max_tokens	= sizeof(struct iw_encode_ext) +
+				  IW_ENCODING_TOKEN_MAX,
+	},
+	[SIOCSIWPMKSA - SIOCIWFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.min_tokens	= sizeof(struct iw_pmksa),
+		.max_tokens	= sizeof(struct iw_pmksa),
+	},
 };
 static const int standard_ioctl_num = (sizeof(standard_ioctl) /
 				       sizeof(struct iw_ioctl_description));
@@ -299,6 +344,31 @@ static const struct iw_ioctl_description standard_event[] = {
 	[IWEVEXPIRED	- IWEVFIRST] = {
 		.header_type	= IW_HEADER_TYPE_ADDR, 
 	},
+	[IWEVGENIE	- IWEVFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.max_tokens	= IW_GENERIC_IE_MAX,
+	},
+	[IWEVMICHAELMICFAILURE	- IWEVFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT, 
+		.token_size	= 1,
+		.max_tokens	= sizeof(struct iw_michaelmicfailure),
+	},
+	[IWEVASSOCREQIE	- IWEVFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.max_tokens	= IW_GENERIC_IE_MAX,
+	},
+	[IWEVASSOCRESPIE	- IWEVFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.max_tokens	= IW_GENERIC_IE_MAX,
+	},
+	[IWEVPMKIDCAND	- IWEVFIRST] = {
+		.header_type	= IW_HEADER_TYPE_POINT,
+		.token_size	= 1,
+		.max_tokens	= sizeof(struct iw_pmkid_cand),
+	},
 };
 static const int standard_event_num = (sizeof(standard_event) /
 				       sizeof(struct iw_ioctl_description));