arm64: dts: qcom: sc7280: Add herobrine-r1

Add the new herobrine-r1. Note that this is pretty much a re-design
compared to herobrine-r0 so we don't attempt any dtsi to share stuff
between them.

This patch attempts to define things at 3 levels:

1. The Qcard level. Herobrine includes a Qcard PCB and the Qcard PCB
   is supposed to be the same (modulo stuffing options) across
   multiple boards, so trying to define what's there hopefully makes
   sense. NOTE that newer "CRD" boards from Qualcomm also use
   Qcard. When support for CRD3 is added hopefully it can use the
   Qcard include (and perhaps we should even evaluate it using
   herobrine.dtsi?)
2. The herobrine "baseboard" level. Right now most stuff is here with
   the exception of things that we _know_ will be different per
   board. We know that not all boards will have the same set of eMMC,
   nvme, and SD. We also know that the exact pin names are likely to
   be different.
3. The actual "board" level, AKA herobrine-rev1.

NOTES:
- This boots to command prompt. We're still waiting on the PWM driver.
- This assumes LTE for now. Once it's clear how WiFi-only SKUs will
  work we expect some small changes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220204140550.v4.1.I5604b7af908e8bbe709ac037a6a8a6ba8a2bfa94@changeid

arch/arm64/boot/dts/qcom/Makefile

@@ -84,6 +84,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-herobrine-r0.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-herobrine-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-crd.dtb

arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r0.dts

@@ -25,8 +25,7 @@
 
 / {
 	model = "Google Herobrine (rev0)";
-	compatible = "google,herobrine",
-		     "qcom,sc7280";
+	compatible = "google,herobrine-rev0", "qcom,sc7280";
 };
 
 / {

arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Herobrine board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine.dtsi"
+
+/ {
+	model = "Google Herobrine (rev1+)";
+	compatible = "google,herobrine", "qcom,sc7280";
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+&ap_spi_fp {
+	status = "okay";
+};
+
+/*
+ * Although the trackpad is really part of the herobrine baseboard, we'll
+ * put the actual definition in the board device tree since different boards
+ * might hook up different trackpads (or no i2c trackpad at all in the case
+ * of tablets / detachables).
+ */
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@15 {
+		compatible = "elan,ekth3000";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		vcc-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+/*
+ * The touchscreen connector might come off the Qcard, at least in the case of
+ * eDP. Like the trackpad, we'll put it in the board device tree file since
+ * different boards have different touchscreens.
+ */
+ts_i2c: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@5c {
+		compatible = "hid-over-i2c";
+		reg = <0x5c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <500>;
+		hid-descr-addr = <0x0000>;
+
+		vdd-supply = <&ts_avdd>;
+	};
+};
+
+/* For nvme */
+&pcie1 {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+	status = "okay";
+};
+
+/* For eMMC */
+&sdhc_1 {
+	status = "okay";
+};
+
+/* For SD Card */
+&sdhc_2 {
+	status = "okay";
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to herobrine board and is named it gets that name.
+ * - If a pin goes to herobrine board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+	gpio-line-names = "FLASH_STROBE_1",		/* 1 */
+			  "AP_SUSPEND",
+			  "PM8008_1_RST_N",
+			  "",
+			  "",
+			  "",
+			  "PMIC_EDP_BL_EN",
+			  "PMIC_EDP_BL_PWM",
+			  "";
+};
+
+&tlmm {
+	gpio-line-names = "AP_TP_I2C_SDA",		/* 0 */
+			  "AP_TP_I2C_SCL",
+			  "SSD_RST_L",
+			  "PE_WAKE_ODL",
+			  "AP_SAR_SDA",
+			  "AP_SAR_SCL",
+			  "PRB_SC_GPIO_6",
+			  "TP_INT_ODL",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+
+			  "GNSS_L1_EN",			/* 10 */
+			  "GNSS_L5_EN",
+			  "SPI_AP_MOSI",
+			  "SPI_AP_MISO",
+			  "SPI_AP_CLK",
+			  "SPI_AP_CS0_L",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_OD.
+			   */
+			  "AP_FLASH_WP",
+			  "",
+			  "AP_EC_INT_L",
+			  "",
+
+			  "UF_CAM_RST_L",		/* 20 */
+			  "WF_CAM_RST_L",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "",
+			  "PM8008_IRQ_1",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "MOS_BT_UART_CTS",
+			  "MOS_BT_UART_RFR",
+
+			  "MOS_BT_UART_TX",		/* 30 */
+			  "MOS_BT_UART_RX",
+			  "PRB_SC_GPIO_32",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "AP_SPI_FP_MISO",
+			  "AP_SPI_FP_MOSI",
+			  "AP_SPI_FP_CLK",
+			  "AP_SPI_FP_CS_L",
+
+			  "AP_EC_SPI_MISO",		/* 40 */
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "LCM_RST_L",
+			  "EARLY_EUD_N",
+			  "",
+			  "DP_HOT_PLUG_DET",
+			  "IO_BRD_MLB_ID0",
+			  "IO_BRD_MLB_ID1",
+
+			  "IO_BRD_MLB_ID2",		/* 50 */
+			  "SSD_EN",
+			  "TS_I2C_SDA_CONN",
+			  "TS_I2C_CLK_CONN",
+			  "TS_RST_CONN",
+			  "TS_INT_CONN",
+			  "AP_I2C_TPM_SDA",
+			  "AP_I2C_TPM_SCL",
+			  "PRB_SC_GPIO_58",
+			  "PRB_SC_GPIO_59",
+
+			  "EDP_HOT_PLUG_DET_N",		/* 60 */
+			  "FP_TO_AP_IRQ_L",
+			  "",
+			  "AMP_EN",
+			  "CAM0_MCLK_GPIO_64",
+			  "CAM1_MCLK_GPIO_65",
+			  "WF_CAM_MCLK",
+			  "PRB_SC_GPIO_67",
+			  "FPMCU_BOOT0",
+			  "UF_CAM_SDA",
+
+			  "UF_CAM_SCL",			/* 70 */
+			  "",
+			  "",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "",
+			  "",
+			  "EN_FP_RAILS",
+			  "FP_RST_L",
+			  "PCIE1_CLKREQ_ODL",
+
+			  "EN_PP3300_DX_EDP",		/* 80 */
+			  "SC_GPIO_81",
+			  "FORCED_USB_BOOT",
+			  "WCD_RESET_N",
+			  "MOS_WLAN_EN",
+			  "MOS_BT_EN",
+			  "MOS_SW_CTRL",
+			  "MOS_PCIE0_RST",
+			  "MOS_PCIE0_CLKREQ_N",
+			  "MOS_PCIE0_WAKE_N",
+
+			  "MOS_LAA_AS_EN",		/* 90 */
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "MOS_BT_WLAN_SLIMBUS_CLK",
+			  "MOS_BT_WLAN_SLIMBUS_DAT0",
+			  "HP_MCLK",
+			  "HP_BCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+
+			  "HP_LRCLK",			/* 100 */
+			  "HP_IRQ",
+			  "",
+			  "",
+			  "GSC_AP_INT_ODL",
+			  "EN_PP3300_CODEC",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM1_DATA_GPIO_109",
+
+			  "UIM1_CLK_GPIO_110",		/* 110 */
+			  "UIM1_RESET_GPIO_111",
+			  "PRB_SC_GPIO_112",
+			  "UIM0_DATA",
+			  "UIM0_CLK",
+			  "UIM0_RST",
+			  "UIM0_PRESENT_ODL",
+			  "SDM_RFFE0_CLK",
+			  "SDM_RFFE0_DATA",
+			  "WF_CAM_EN",
+
+			  "FASTBOOT_SEL_0",		/* 120 */
+			  "SC_GPIO_121",
+			  "FASTBOOT_SEL_1",
+			  "SC_GPIO_123",
+			  "FASTBOOT_SEL_2",
+			  "SM_RFFE4_CLK_GRFC_8",
+			  "SM_RFFE4_DATA_GRFC_9",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "PRB_SC_GPIO_129",
+
+			  "LCM_ID0",			/* 130 */
+			  "LCM_ID1",
+			  "",
+			  "SDR_QLINK_REQ",
+			  "SDR_QLINK_EN",
+			  "QLINK0_WMSS_RESET_N",
+			  "SMR526_QLINK1_REQ",
+			  "SMR526_QLINK1_EN",
+			  "SMR526_QLINK1_WMSS_RESET_N",
+			  "PRB_SC_GPIO_139",
+
+			  "SAR1_IRQ_ODL",		/* 140 */
+			  "SAR0_IRQ_ODL",
+			  "PRB_SC_GPIO_142",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1",
+
+			  "DMIC01_CLK",			/* 150 */
+			  "DMIC01_DATA",
+			  "DMIC23_CLK",
+			  "DMIC23_DATA",
+			  "",
+			  "",
+			  "EC_IN_RW_ODL",
+			  "HUB_EN",
+			  "WCD_SWR_TX_DATA2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "MOS_BLE_UART_TX",
+			  "MOS_BLE_UART_RX",
+			  "",
+			  "",
+			  "";
+};