Merge

Documentation/ide.txt

@@ -37,9 +37,27 @@
 ***
 ***  Use of the "serialize" option is no longer necessary.
 
-This is the multiple IDE interface driver, as evolved from hd.c.  It supports
-up to 9 IDE interfaces per default, on one or more IRQs (usually 14 & 15).
-There can be up to two drives per interface, as per the ATA-6 spec.
+================================================================================
+Common pitfalls:
+
+- 40-conductor IDE cables are capable of transfering data in DMA modes up to
+  udma2, but no faster.
+
+- If possible devices should be attached to separate channels if they are
+  available. Typically the disk on the first and CD-ROM on the second.
+
+- If you mix devices on the same cable, please consider using similar devices
+  in respect of the data transfer mode they support.
+
+- Even better tru to stick to the same vendor and device type on the same
+  cable.
+
+================================================================================
+
+This is the multiple IDE interface driver, as evolved from hd.c.  
+
+It supports up to 9 IDE interfaces per default, on one or more IRQs (usually
+14 & 15).  There can be up to two drives per interface, as per the ATA-6 spec.
 
 Primary:    ide0, port 0x1f0; major=3;  hda is minor=0; hdb is minor=64
 Secondary:  ide1, port 0x170; major=22; hdc is minor=0; hdd is minor=64

arch/cris/drivers/ide.c

@@ -192,7 +192,7 @@ unsigned char IN_BYTE(ide_ioreg_t reg) {
 #define ATA_PIO0_HOLD    4
 
 static int e100_dmaproc(ide_dma_action_t func, struct ata_device *drive, struct request *rq);
-static void e100_ideproc (ide_ide_action_t func, ide_drive_t *drive,
+static void e100_ideproc (ide_ide_action_t func, struct ata_device *drive,
 			  void *buffer, unsigned int length);
 
 /*
@@ -206,7 +206,7 @@ const char *good_dma_drives[] = {"Micropolis 2112A",
 				 "CONNER CTT8000-A",
 				 NULL};
 
-static void tune_e100_ide(ide_drive_t *drive, byte pio)
+static void tune_e100_ide(struct ata_device *drive, byte pio)
 {
 	unsigned long flags;
 	
@@ -380,7 +380,7 @@ static etrax_dma_descr mydescr;
  * extra byte allocated for the buffer.
  */
 static void
-e100_atapi_read(ide_drive_t *drive, void *buffer, unsigned int bytecount)
+e100_atapi_read(struct ata_device *drive, void *buffer, unsigned int bytecount)
 {
 	ide_ioreg_t data_reg = IDE_DATA_REG;
 
@@ -459,7 +459,7 @@ e100_atapi_read(ide_drive_t *drive, void *buffer, unsigned int bytecount)
 }
 
 static void
-e100_atapi_write(ide_drive_t *drive, void *buffer, unsigned int bytecount)
+e100_atapi_write(struct ata_device *drive, void *buffer, unsigned int bytecount)
 {
 	ide_ioreg_t data_reg = IDE_DATA_REG;
 	
@@ -546,7 +546,7 @@ e100_atapi_write(ide_drive_t *drive, void *buffer, unsigned int bytecount)
  * This is used for most PIO data transfers *from* the IDE interface
  */
 static void 
-e100_ide_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount)
+e100_ide_input_data (struct ata_device *drive, void *buffer, unsigned int wcount)
 {
 	e100_atapi_read(drive, buffer, wcount << 2);
 }
@@ -555,7 +555,7 @@ e100_ide_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount)
  * This is used for most PIO data transfers *to* the IDE interface
  */
 static void
-e100_ide_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount)
+e100_ide_output_data (struct ata_device *drive, void *buffer, unsigned int wcount)
 {
 	e100_atapi_write(drive, buffer, wcount << 2);
 }
@@ -661,7 +661,7 @@ static int e100_udma_new_table(struct ata_channel *ch, struct request *rq)
 	return 1;	/* let the PIO routines handle this weirdness */
 }
 
-static int config_drive_for_dma (ide_drive_t *drive)
+static int config_drive_for_dma (struct ata_device *drive)
 {
         const char **list;
         struct hd_driveid *id = drive->id;

drivers/ide/Config.in

@@ -131,12 +131,7 @@ if [ "$CONFIG_BLK_DEV_IDE" != "n" ]; then
       bool '  IGNORE word93 Validation BITS' CONFIG_IDEDMA_IVB
    fi
    
-   if [ "$CONFIG_BLK_DEV_IDECD" != "n" -o \
-        "$CONFIG_BLK_DEV_IDETAPE" != "n" -o \
-        "$CONFIG_BLK_DEV_IDEFLOPPY" != "n" -o \
-        "$CONFIG_BLK_DEV_IDESCSI" != "n" ]; then
-	define_bool  CONFIG_ATAPI y
-   fi
+   define_bool  CONFIG_ATAPI y
 else
    bool 'Old hard disk (MFM/RLL/IDE) driver' CONFIG_BLK_DEV_HD_ONLY
    define_bool CONFIG_BLK_DEV_HD $CONFIG_BLK_DEV_HD_ONLY

drivers/ide/Makefile

@@ -21,7 +21,7 @@ obj-$(CONFIG_BLK_DEV_HD)	+= hd.o
 obj-$(CONFIG_BLK_DEV_IDE)       += ide-mod.o
 obj-$(CONFIG_BLK_DEV_IDECS)     += ide-cs.o
 obj-$(CONFIG_BLK_DEV_IDEDISK)   += ide-disk.o
-obj-$(CONFIG_ATAPI)		+= atapi.o
+# obj-$(CONFIG_ATAPI)		+= atapi.o
 obj-$(CONFIG_BLK_DEV_IDECD)     += ide-cd.o
 obj-$(CONFIG_BLK_DEV_IDETAPE)   += ide-tape.o
 obj-$(CONFIG_BLK_DEV_IDEFLOPPY) += ide-floppy.o
@@ -74,6 +74,6 @@ obj-$(CONFIG_BLK_DEV_ATARAID)		+= ataraid.o
 obj-$(CONFIG_BLK_DEV_ATARAID_PDC)	+= pdcraid.o
 obj-$(CONFIG_BLK_DEV_ATARAID_HPT)	+= hptraid.o
 
-ide-mod-objs	:= ide-taskfile.o ide.o ide-probe.o ide-geometry.o ide-features.o ata-timing.o $(ide-obj-y)
+ide-mod-objs	:= ide-taskfile.o ide.o ide-probe.o ide-geometry.o ide-features.o ata-timing.o atapi.o $(ide-obj-y)
 
 include $(TOPDIR)/Rules.make

drivers/ide/aec62xx.c

@@ -607,27 +607,7 @@ static struct ata_pci_device chipsets[] __initdata = {
 		enablebits: { {0x00,0x00,0x00},	{0x00,0x00,0x00} },
 		bootable: OFF_BOARD,
 		flags: ATA_F_IRQ | ATA_F_DMA
-	},
-	{
-		vendor: PCI_VENDOR_ID_ARTOP,
-		device: PCI_DEVICE_ID_ARTOP_ATP865,
-		init_chipset: aec62xx_init_chipset,
-		ata66_check: aec62xx_ata66_check,
-		init_channel: aec62xx_init_channel,
-		enablebits: { {0x00,0x00,0x00},	{0x00,0x00,0x00} },
-		bootable: NEVER_BOARD,
-		flags: ATA_F_IRQ | ATA_F_NOADMA | ATA_F_DMA
-	},
-	{
-		vendor: PCI_VENDOR_ID_ARTOP,
-		device: PCI_DEVICE_ID_ARTOP_ATP865R,
-		init_chipset: aec62xx_init_chipset,
-		ata66_check: aec62xx_ata66_check,
-		init_channel: aec62xx_init_channel,
-		enablebits: { {0x4a,0x02,0x02},	{0x4a,0x04,0x04} },
-		bootable: OFF_BOARD,
-		flags: ATA_F_IRQ | ATA_F_DMA
-	},
+	}
 };
 
 int __init init_aec62xx(void)

drivers/ide/amd74xx.c

@@ -226,9 +226,9 @@ static void amd_set_speed(struct pci_dev *dev, unsigned char dn, struct ata_timi
  * by upper layers.
  */
 
-static int amd_set_drive(ide_drive_t *drive, unsigned char speed)
+static int amd_set_drive(struct ata_device *drive, unsigned char speed)
 {
-	ide_drive_t *peer = drive->channel->drives + (~drive->dn & 1);
+	struct ata_device *peer = drive->channel->drives + (~drive->dn & 1);
 	struct ata_timing t, p;
 	int T, UT;
 
@@ -263,7 +263,7 @@ static int amd_set_drive(ide_drive_t *drive, unsigned char speed)
  * PIO-only tuning.
  */
 
-static void amd74xx_tune_drive(ide_drive_t *drive, unsigned char pio)
+static void amd74xx_tune_drive(struct ata_device *drive, u8 pio)
 {
 	if (!((amd_enabled >> drive->channel->unit) & 1))
 		return;

drivers/ide/cs5530.c

@@ -81,7 +81,7 @@ extern char *ide_xfer_verbose (byte xfer_rate);
 /*
  * Set a new transfer mode at the drive
  */
-int cs5530_set_xfer_mode (ide_drive_t *drive, byte mode)
+int cs5530_set_xfer_mode(struct ata_device *drive, byte mode)
 {
 	int error = 0;
 
@@ -113,7 +113,7 @@ static unsigned int cs5530_pio_timings[2][5] =
  * The ide_init_cs5530() routine guarantees that all drives
  * will have valid default PIO timings set up before we get here.
  */
-static void cs5530_tuneproc (ide_drive_t *drive, byte pio)	/* pio=255 means "autotune" */
+static void cs5530_tuneproc(struct ata_device *drive, byte pio)	/* pio=255 means "autotune" */
 {
 	struct ata_channel *hwif = drive->channel;
 	unsigned int	format, basereg = CS5530_BASEREG(hwif);
@@ -134,12 +134,12 @@ static void cs5530_tuneproc (ide_drive_t *drive, byte pio)	/* pio=255 means "aut
  * cs5530_config_dma() handles selection/setting of DMA/UDMA modes
  * for both the chipset and drive.
  */
-static int cs5530_config_dma (ide_drive_t *drive)
+static int cs5530_config_dma(struct ata_device *drive)
 {
 	int			udma_ok = 1, mode = 0;
 	struct ata_channel *hwif = drive->channel;
 	int			unit = drive->select.b.unit;
-	ide_drive_t		*mate = &hwif->drives[unit^1];
+	struct ata_device		*mate = &hwif->drives[unit^1];
 	struct hd_driveid	*id = drive->id;
 	unsigned int		basereg, reg, timings;
 

drivers/ide/cy82c693.c

@@ -183,7 +183,7 @@ static void compute_clocks (byte pio, pio_clocks_t *p_pclk)
 /*
  * set DMA mode a specific channel for CY82C693
  */
-static void cy82c693_dma_enable (ide_drive_t *drive, int mode, int single)
+static void cy82c693_dma_enable(struct ata_device *drive, int mode, int single)
 {
         byte index;
 	byte data;
@@ -270,7 +270,7 @@ static int cy82c693_dmaproc(struct ata_device *drive)
 /*
  * tune ide drive - set PIO mode
  */
-static void cy82c693_tune_drive (ide_drive_t *drive, byte pio)
+static void cy82c693_tune_drive(struct ata_device *drive, byte pio)
 {
 	struct ata_channel *hwif = drive->channel;
 	struct pci_dev *dev = hwif->pci_dev;

drivers/ide/dtc2278.c

@@ -66,7 +66,7 @@ static void sub22 (char b, char c)
 	}
 }
 
-static void tune_dtc2278 (ide_drive_t *drive, byte pio)
+static void tune_dtc2278(struct ata_device *drive, byte pio)
 {
 	unsigned long flags;
 

drivers/ide/hpt34x.c

@@ -94,9 +94,9 @@ static int hpt34x_get_info (char *buffer, char **addr, off_t offset, int count)
 
 byte hpt34x_proc = 0;
 
-extern char *ide_xfer_verbose (byte xfer_rate);
+extern char *ide_xfer_verbose(byte xfer_rate);
 
-static void hpt34x_clear_chipset (ide_drive_t *drive)
+static void hpt34x_clear_chipset(struct ata_device *drive)
 {
 	unsigned int reg1	= 0, tmp1 = 0;
 	unsigned int reg2	= 0, tmp2 = 0;
@@ -109,7 +109,7 @@ static void hpt34x_clear_chipset (ide_drive_t *drive)
 	pci_write_config_dword(drive->channel->pci_dev, 0x48, tmp2);
 }
 
-static int hpt34x_tune_chipset (ide_drive_t *drive, byte speed)
+static int hpt34x_tune_chipset(struct ata_device *drive, byte speed)
 {
 	byte			hi_speed, lo_speed;
 	unsigned int reg1	= 0, tmp1 = 0;
@@ -145,7 +145,7 @@ static int hpt34x_tune_chipset (ide_drive_t *drive, byte speed)
 	return ide_config_drive_speed(drive, speed);
 }
 
-static void config_chipset_for_pio(ide_drive_t *drive)
+static void config_chipset_for_pio(struct ata_device *drive)
 {
 	unsigned short eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
 	unsigned short xfer_pio = drive->id->eide_pio_modes;
@@ -182,7 +182,7 @@ static void config_chipset_for_pio(ide_drive_t *drive)
 	(void) hpt34x_tune_chipset(drive, speed);
 }
 
-static void hpt34x_tune_drive (ide_drive_t *drive, byte pio)
+static void hpt34x_tune_drive(struct ata_device *drive, byte pio)
 {
 	byte speed;
 

drivers/ide/hptraid.c

@@ -230,14 +230,14 @@ static unsigned long maxsectors (int major,int minor)
 {
 	unsigned long lba = 0;
 	kdev_t dev;
-	ide_drive_t *ideinfo;
-	
+	struct ata_device *ideinfo;
+
 	dev = mk_kdev(major,minor);
 	ideinfo = get_info_ptr (dev);
 	if (ideinfo==NULL)
 		return 0;
-	
-	
+
+
 	/* first sector of the last cluster */
 	if (ideinfo->head==0) 
 		return 0;

drivers/ide/ht6560b.c

@@ -120,7 +120,7 @@
 /*
  * This routine is invoked from ide.c to prepare for access to a given drive.
  */
-static void ht6560b_selectproc (ide_drive_t *drive)
+static void ht6560b_selectproc(struct ata_device *drive)
 {
 	unsigned long flags;
 	static byte current_select = 0;
@@ -195,7 +195,7 @@ static int __init try_to_init_ht6560b(void)
 	return 1;
 }
 
-static byte ht_pio2timings(ide_drive_t *drive, byte pio)
+static byte ht_pio2timings(struct ata_device *drive, byte pio)
 {
 	int active_time, recovery_time;
 	int active_cycles, recovery_cycles;
@@ -248,7 +248,7 @@ static byte ht_pio2timings(ide_drive_t *drive, byte pio)
 /*
  *  Enable/Disable so called prefetch mode
  */
-static void ht_set_prefetch(ide_drive_t *drive, byte state)
+static void ht_set_prefetch(struct ata_device *drive, byte state)
 {
 	unsigned long flags;
 	int t = HT_PREFETCH_MODE << 8;
@@ -275,7 +275,7 @@ static void ht_set_prefetch(ide_drive_t *drive, byte state)
 #endif
 }
 
-static void tune_ht6560b (ide_drive_t *drive, byte pio)
+static void tune_ht6560b(struct ata_device *drive, byte pio)
 {
 	unsigned long flags;
 	byte timing;

drivers/ide/ide-cd.c

@@ -2925,8 +2925,11 @@ int ide_cdrom_cleanup(struct ata_device *drive)
 	return 0;
 }
 
+static void ide_cdrom_attach(struct ata_device *drive);
+
 static struct ata_operations ide_cdrom_driver = {
 	owner:			THIS_MODULE,
+	attach:			ide_cdrom_attach,
 	cleanup:		ide_cdrom_cleanup,
 	standby:		NULL,
 	do_request:		ide_cdrom_do_request,
@@ -2942,67 +2945,63 @@ static struct ata_operations ide_cdrom_driver = {
 /* options */
 static char *ignore = NULL;
 
+static void ide_cdrom_attach(struct ata_device *drive)
+{
+	struct cdrom_info *info;
+	char *req;
+	struct ata_channel *channel;
+	int unit;
+
+	if (drive->type != ATA_ROM)
+		return;
+
+	req = drive->driver_req;
+	if (req[0] != '\0' && strcmp(req, "ide-cdrom"))
+		return;
+
+	/* skip drives that we were told to ignore */
+	if (ignore && !strcmp(ignore, drive->name)) {
+		printk(KERN_INFO "%s: ignored\n", drive->name);
+		return;
+	}
+	info = (struct cdrom_info *) kmalloc (sizeof (struct cdrom_info), GFP_KERNEL);
+	if (!info) {
+		printk(KERN_ERR "%s: Can't allocate a cdrom structure\n", drive->name);
+		return;
+	}
+	if (ide_register_subdriver (drive, &ide_cdrom_driver)) {
+		printk(KERN_ERR "%s: Failed to register the driver with ide.c\n", drive->name);
+		kfree (info);
+		return;
+	}
+
+
+	memset(info, 0, sizeof (struct cdrom_info));
+	drive->driver_data = info;
+
+	if (ide_cdrom_setup (drive)) {
+		if (ide_cdrom_cleanup (drive))
+			printk (KERN_ERR "%s: ide_cdrom_cleanup failed in ide_cdrom_init\n", drive->name);
+		return;
+	}
+
+	channel = drive->channel;
+	unit = drive - channel->drives;
+
+	ide_revalidate_disk(mk_kdev(channel->major, unit << PARTN_BITS));
+}
+
 MODULE_PARM(ignore, "s");
 MODULE_DESCRIPTION("ATAPI CD-ROM Driver");
 
 static void __exit ide_cdrom_exit(void)
 {
-	struct ata_device *drive;
-	int failed = 0;
-
-	while ((drive = ide_scan_devices(ATA_ROM, "ide-cdrom", &ide_cdrom_driver, failed)) != NULL)
-		if (ide_cdrom_cleanup (drive)) {
-			printk ("%s: cleanup_module() called while still busy\n", drive->name);
-			failed++;
-		}
+	unregister_ata_driver(&ide_cdrom_driver);
 }
 
 int ide_cdrom_init(void)
 {
-	struct ata_device *drive;
-	struct cdrom_info *info;
-	int failed = 0;
-
-	MOD_INC_USE_COUNT;
-	while ((drive = ide_scan_devices (ATA_ROM, "ide-cdrom", NULL, failed++)) != NULL) {
-		/* skip drives that we were told to ignore */
-		if (ignore != NULL) {
-			if (strstr(ignore, drive->name)) {
-				printk("ide-cd: ignoring drive %s\n", drive->name);
-				continue;
-			}
-		}
-		if (drive->scsi) {
-			printk("ide-cd: passing drive %s to ide-scsi emulation.\n", drive->name);
-			continue;
-		}
-		info = (struct cdrom_info *) kmalloc (sizeof (struct cdrom_info), GFP_KERNEL);
-		if (info == NULL) {
-			printk ("%s: Can't allocate a cdrom structure\n", drive->name);
-			continue;
-		}
-		if (ide_register_subdriver (drive, &ide_cdrom_driver)) {
-			printk ("%s: Failed to register the driver with ide.c\n", drive->name);
-			kfree (info);
-			continue;
-		}
-		memset(info, 0, sizeof (struct cdrom_info));
-		drive->driver_data = info;
-
-		MOD_INC_USE_COUNT;
-		if (ide_cdrom_setup (drive)) {
-			MOD_DEC_USE_COUNT;
-			if (ide_cdrom_cleanup (drive))
-				printk ("%s: ide_cdrom_cleanup failed in ide_cdrom_init\n", drive->name);
-			continue;
-		}
-		MOD_DEC_USE_COUNT;
-
-		failed--;
-	}
-	revalidate_drives();
-	MOD_DEC_USE_COUNT;
-	return 0;
+	return ata_driver_module(&ide_cdrom_driver);
 }
 
 module_init(ide_cdrom_init);

drivers/ide/ide-disk.c

@@ -913,7 +913,7 @@ static void idedisk_setup(struct ata_device *drive)
 	if ((capacity >= (drive->bios_cyl * drive->bios_sect * drive->bios_head)) &&
 	    (!drive->forced_geom) && drive->bios_sect && drive->bios_head)
 		drive->bios_cyl = (capacity / drive->bios_sect) / drive->bios_head;
-	printk(KERN_INFO "%s: %ld sectors", drive->name, capacity);
+	printk(KERN_INFO " %s: %ld sectors", drive->name, capacity);
 
 #if 0
 
@@ -1149,12 +1149,14 @@ static int idedisk_ioctl(struct ata_device *drive, struct inode *inode, struct f
 	}
 }
 
+static void idedisk_attach(struct ata_device *drive);
 
 /*
  * Subdriver functions.
  */
 static struct ata_operations idedisk_driver = {
 	owner:			THIS_MODULE,
+	attach:			idedisk_attach,
 	cleanup:		idedisk_cleanup,
 	standby:		idedisk_standby,
 	do_request:		idedisk_do_request,
@@ -1167,46 +1169,49 @@ static struct ata_operations idedisk_driver = {
 	capacity:		idedisk_capacity,
 };
 
-MODULE_DESCRIPTION("ATA DISK Driver");
-
-static void __exit idedisk_exit (void)
+static void idedisk_attach(struct ata_device *drive)
 {
-	struct ata_device *drive;
-	int failed = 0;
+	char *req;
+	struct ata_channel *channel;
+	int unit;
 
-	while ((drive = ide_scan_devices(ATA_DISK, "ide-disk", &idedisk_driver, failed)) != NULL) {
-		if (idedisk_cleanup (drive)) {
-			printk(KERN_ERR "%s: cleanup_module() called while still busy\n", drive->name);
-			++failed;
-		}
+	if (drive->type != ATA_DISK)
+		return;
+
+	req = drive->driver_req;
+	if (req[0] != '\0' && strcmp(req, "ide-disk"))
+		return;
+
+	if (ide_register_subdriver(drive, &idedisk_driver)) {
+		printk (KERN_ERR "ide-disk: %s: Failed to register the driver with ide.c\n", drive->name);
+		return;
+	}
+
+	idedisk_setup(drive);
+	if ((!drive->head || drive->head > 16) && !drive->select.b.lba) {
+		printk(KERN_ERR "%s: INVALID GEOMETRY: %d PHYSICAL HEADS?\n", drive->name, drive->head);
+		idedisk_cleanup(drive);
+		return;
 	}
+
+	channel = drive->channel;
+	unit = drive - channel->drives;
+
+	ide_revalidate_disk(mk_kdev(channel->major, unit << PARTN_BITS));
 }
 
-int idedisk_init(void)
+static void __exit idedisk_exit(void)
 {
-	struct ata_device *drive;
-	int failed = 0;
-
-	MOD_INC_USE_COUNT;
-	while ((drive = ide_scan_devices(ATA_DISK, "ide-disk", NULL, failed++)) != NULL) {
-		if (ide_register_subdriver (drive, &idedisk_driver)) {
-			printk (KERN_ERR "ide-disk: %s: Failed to register the driver with ide.c\n", drive->name);
-			continue;
-		}
-		idedisk_setup(drive);
-		if ((!drive->head || drive->head > 16) && !drive->select.b.lba) {
-			printk(KERN_ERR "%s: INVALID GEOMETRY: %d PHYSICAL HEADS?\n", drive->name, drive->head);
-			idedisk_cleanup(drive);
-			continue;
-		}
-		--failed;
-	}
-	revalidate_drives();
-	MOD_DEC_USE_COUNT;
+	unregister_ata_driver(&idedisk_driver);
+}
 
-	return 0;
+int __init idedisk_init(void)
+{
+	return ata_driver_module(&idedisk_driver);
 }
 
 module_init(idedisk_init);
 module_exit(idedisk_exit);
+
+MODULE_DESCRIPTION("ATA DISK Driver");
 MODULE_LICENSE("GPL");

drivers/ide/ide-floppy.c

 /*
- * linux/drivers/ide/ide-floppy.c	Version 0.99	Feb 24 2002
- *
  * Copyright (C) 1996 - 1999 Gadi Oxman <gadio@netvision.net.il>
  * Copyright (C) 2000 - 2002 Paul Bristow <paul@paulbristow.net>
  */
@@ -1977,11 +1975,14 @@ static int idefloppy_cleanup(struct ata_device *drive)
 	return 0;
 }
 
+static void idefloppy_attach(struct ata_device *drive);
+
 /*
  *	IDE subdriver functions, registered with ide.c
  */
 static struct ata_operations idefloppy_driver = {
 	owner:			THIS_MODULE,
+	attach:			idefloppy_attach,
 	cleanup:		idefloppy_cleanup,
 	standby:		NULL,
 	do_request:		idefloppy_do_request,
@@ -1994,59 +1995,60 @@ static struct ata_operations idefloppy_driver = {
 	capacity:		idefloppy_capacity,
 };
 
-MODULE_DESCRIPTION("ATAPI FLOPPY Driver");
-
-static void __exit idefloppy_exit(void)
+static void idefloppy_attach(struct ata_device *drive)
 {
-	struct ata_device *drive;
-	int failed = 0;
+	idefloppy_floppy_t *floppy;
+	char *req;
+	struct ata_channel *channel;
+	int unit;
 
-	while ((drive = ide_scan_devices(ATA_FLOPPY, "ide-floppy", &idefloppy_driver, failed)) != NULL) {
-		if (idefloppy_cleanup(drive)) {
-			printk ("%s: cleanup_module() called while still busy\n", drive->name);
-			failed++;
-		}
+	if (drive->type != ATA_FLOPPY)
+		return;
+
+	req = drive->driver_req;
+	if (req[0] != '\0' && strcmp(req, "ide-floppy"))
+		return;
+
+	if (!idefloppy_identify_device (drive, drive->id)) {
+		printk (KERN_ERR "ide-floppy: %s: not supported by this version of driver\n",
+				drive->name);
+		return;
+	}
+
+	if (drive->scsi) {
+		printk(KERN_INFO "ide-floppy: passing drive %s to ide-scsi emulation.\n",
+				drive->name);
+		return;
+	}
+	if (!(floppy = (idefloppy_floppy_t *) kmalloc (sizeof (idefloppy_floppy_t), GFP_KERNEL))) {
+		printk(KERN_ERR "ide-floppy: %s: Can't allocate a floppy structure\n",
+				drive->name);
+		return;
+	}
+	if (ide_register_subdriver(drive, &idefloppy_driver)) {
+		printk(KERN_ERR "ide-floppy: %s: Failed to register the driver with ide.c\n", drive->name);
+		kfree (floppy);
+		return;
 	}
+
+	idefloppy_setup(drive, floppy);
+
+	channel = drive->channel;
+	unit = drive - channel->drives;
+
+	ide_revalidate_disk(mk_kdev(channel->major, unit << PARTN_BITS));
 }
 
-/*
- *	idefloppy_init will register the driver for each floppy.
- */
-int idefloppy_init(void)
-{
-	struct ata_device *drive;
-	idefloppy_floppy_t *floppy;
-	int failed = 0;
+MODULE_DESCRIPTION("ATAPI FLOPPY Driver");
 
-	printk("ide-floppy driver " IDEFLOPPY_VERSION "\n");
-	MOD_INC_USE_COUNT;
-	while ((drive = ide_scan_devices (ATA_FLOPPY, "ide-floppy", NULL, failed++)) != NULL) {
-		if (!idefloppy_identify_device (drive, drive->id)) {
-			printk (KERN_ERR "ide-floppy: %s: not supported by this version of ide-floppy\n", drive->name);
-			continue;
-		}
-		if (drive->scsi) {
-			printk("ide-floppy: passing drive %s to ide-scsi emulation.\n", drive->name);
-			continue;
-		}
-		if ((floppy = (idefloppy_floppy_t *) kmalloc (sizeof (idefloppy_floppy_t), GFP_KERNEL)) == NULL) {
-			printk (KERN_ERR "ide-floppy: %s: Can't allocate a floppy structure\n", drive->name);
-			continue;
-		}
-		if (ide_register_subdriver (drive, &idefloppy_driver)) {
-			printk (KERN_ERR "ide-floppy: %s: Failed to register the driver with ide.c\n", drive->name);
-			kfree (floppy);
-			continue;
-		}
-		MOD_INC_USE_COUNT;
-		idefloppy_setup (drive, floppy);
-		MOD_DEC_USE_COUNT;
+static void __exit idefloppy_exit(void)
+{
+	unregister_ata_driver(&idefloppy_driver);
+}
 
-		failed--;
-	}
-	revalidate_drives();
-	MOD_DEC_USE_COUNT;
-	return 0;
+int __init idefloppy_init(void)
+{
+	return ata_driver_module(&idefloppy_driver);
 }
 
 module_init(idefloppy_init);

drivers/ide/ide-m8xx.c

@@ -51,7 +51,7 @@ static void print_funcid (int func);
 static int check_ide_device (unsigned long base);
 
 static void ide_interrupt_ack (void *dev);
-static void m8xx_ide_tuneproc(ide_drive_t *drive, byte pio);
+static void m8xx_ide_tuneproc(struct ata_device *drive, byte pio);
 
 typedef	struct ide_ioport_desc {
 	unsigned long	base_off;		/* Offset to PCMCIA memory	*/
@@ -437,7 +437,7 @@ void m8xx_ide_init_hwif_ports (hw_regs_t *hw,
 
 /* Calculate PIO timings */
 static void
-m8xx_ide_tuneproc(ide_drive_t *drive, byte pio)
+m8xx_ide_tuneproc(struct ata_device *drive, byte pio)
 {
 #if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_DIRECT)
 	volatile pcmconf8xx_t	*pcmp;

drivers/ide/ide-pci.c

@@ -207,7 +207,8 @@ static unsigned long __init get_dma_base(struct ata_channel *hwif, int extra, co
 
 	if ((dev->vendor == PCI_VENDOR_ID_AL && dev->device == PCI_DEVICE_ID_AL_M5219) ||
 			(dev->vendor == PCI_VENDOR_ID_AMD && dev->device == PCI_DEVICE_ID_AMD_VIPER_7409) ||
-			(dev->vendor == PCI_VENDOR_ID_CMD && dev->device == PCI_DEVICE_ID_CMD_643)) {
+			(dev->vendor == PCI_VENDOR_ID_CMD && dev->device == PCI_DEVICE_ID_CMD_643) ||
+			(dev->vendor == PCI_VENDOR_ID_SERVERWORKS && dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)) {
 		outb(inb(dma_base + 2) & 0x60, dma_base+2);
 		if (inb(dma_base + 2) & 0x80)
 			printk(KERN_INFO "%s: simplex device: DMA forced\n", name);
@@ -553,14 +554,14 @@ static void __init pdc20270_device_order_fixup (struct pci_dev *dev, struct ata_
 			}
 		}
 	}
-	printk(KERN_INFO "ATA: %s: controller on PCI slot %s dev %02x\n",
-			dev->name, dev->slot_name, dev->devfn);
+	printk(KERN_INFO "ATA: %s: controller, PCI slot %s\n",
+			dev->name, dev->slot_name);
 	setup_pci_device(dev, d);
 	if (!dev2)
 		return;
 	d2 = d;
-	printk(KERN_INFO "ATA: %s: controller on PCI slot %s dev %02x\n",
-			dev2->name, dev2->slot_name, dev2->devfn);
+	printk(KERN_INFO "ATA: %s: controller, PCI slot %s\n",
+			dev2->name, dev2->slot_name);
 	setup_pci_device(dev2, d2);
 }
 
@@ -583,8 +584,8 @@ static void __init hpt374_device_order_fixup (struct pci_dev *dev, struct ata_pc
 		}
 	}
 
-	printk(KERN_INFO "ATA: %s: controller on PCI slot %s dev %02x\n",
-		dev->name, dev->slot_name, dev->devfn);
+	printk(KERN_INFO "ATA: %s: controller, PCI slot %s\n",
+		dev->name, dev->slot_name);
 	setup_pci_device(dev, d);
 	if (!dev2) {
 		return;
@@ -600,8 +601,8 @@ static void __init hpt374_device_order_fixup (struct pci_dev *dev, struct ata_pc
 		}
 	}
 	d2 = d;
-	printk(KERN_INFO "ATA: %s: controller on PCI slot %s dev %02x\n",
-		dev2->name, dev2->slot_name, dev2->devfn);
+	printk(KERN_INFO "ATA: %s: controller, PCI slot %s\n",
+		dev2->name, dev2->slot_name);
 	setup_pci_device(dev2, d2);
 
 }
@@ -622,7 +623,8 @@ static void __init hpt366_device_order_fixup (struct pci_dev *dev, struct ata_pc
 	switch(class_rev) {
 		case 5:
 		case 4:
-		case 3:	printk(KERN_INFO "ATA: %s: controller on PCI slot %s\n", dev->name, dev->slot_name);
+		case 3:	printk(KERN_INFO "ATA: %s: controller, PCI slot %s\n",
+					dev->name, dev->slot_name);
 			setup_pci_device(dev, d);
 			return;
 		default:	break;
@@ -643,12 +645,14 @@ static void __init hpt366_device_order_fixup (struct pci_dev *dev, struct ata_pc
 			break;
 		}
 	}
-	printk(KERN_INFO "ATA: %s: controller on PCI slot %s\n", dev->name, dev->slot_name);
+	printk(KERN_INFO "ATA: %s: controller, PCI slot %s\n",
+			dev->name, dev->slot_name);
 	setup_pci_device(dev, d);
 	if (!dev2)
 		return;
 	d2 = d;
-	printk(KERN_INFO "ATA: %s: controller on PCI slot %s\n", dev2->name, dev2->slot_name);
+	printk(KERN_INFO "ATA: %s: controller, PCI slot %s\n",
+			dev2->name, dev2->slot_name);
 	setup_pci_device(dev2, d2);
 }
 
@@ -683,7 +687,7 @@ static void __init scan_pcidev(struct pci_dev *dev)
 		 * beeing grabbed by generic drivers.
 		 */
 		if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
-			printk(KERN_INFO "ATA: unknown interface: %s, on PCI slot %s\n",
+			printk(KERN_INFO "ATA: unknown interface: %s, PCI slot %s\n",
 					dev->name, dev->slot_name);
 		}
 		return;
@@ -707,8 +711,8 @@ static void __init scan_pcidev(struct pci_dev *dev)
 	} else if (d->vendor == PCI_VENDOR_ID_PROMISE && d->device == PCI_DEVICE_ID_PROMISE_20268R)
 		pdc20270_device_order_fixup(dev, d);
 	else {
-		printk(KERN_INFO "ATA: %s (%04x:%04x) on PCI slot %s\n",
-				dev->name, vendor, device, dev->slot_name);
+		printk(KERN_INFO "ATA: %s, PCI slot %s\n",
+				dev->name, dev->slot_name);
 		setup_pci_device(dev, d);
 	}
 }

drivers/ide/ide-tape.c

 /*
- * linux/drivers/ide/ide-tape.c		Version 1.17a	Jan, 2001
- *
  * Copyright (C) 1995 - 1999 Gadi Oxman <gadio@netvision.net.il>
  *
- * $Header$
- *
  * This driver was constructed as a student project in the software laboratory
  * of the faculty of electrical engineering in the Technion - Israel's
  * Institute Of Technology, with the guide of Avner Lottem and Dr. Ilana David.
@@ -5849,7 +5845,7 @@ static void idetape_get_mode_sense_results(struct ata_device *drive)
 	printk (KERN_INFO "ide-tape: Medium Type - %d\n",header->medium_type);
 	printk (KERN_INFO "ide-tape: Device Specific Parameter - %d\n",header->dsp);
 	printk (KERN_INFO "ide-tape: Block Descriptor Length - %d\n",header->bdl);
-	
+
 	printk (KERN_INFO "ide-tape: Capabilities and Mechanical Status Page:\n");
 	printk (KERN_INFO "ide-tape: Page code - %d\n",capabilities->page_code);
 	printk (KERN_INFO "ide-tape: Page length - %d\n",capabilities->page_length);
@@ -5955,7 +5951,7 @@ static void idetape_setup(struct ata_device *drive, idetape_tape_t *tape, int mi
 		set_bit(IDETAPE_DRQ_INTERRUPT, &tape->flags);
 
 	tape->min_pipeline = tape->max_pipeline = tape->max_stages = 10;
-	
+
 	idetape_get_inquiry_results(drive);
 	idetape_get_mode_sense_results(drive);
 	idetape_get_blocksize_from_block_descriptor(drive);
@@ -6054,11 +6050,11 @@ static void idetape_revalidate(struct ata_device *_dummy)
 	 */
 }
 
-/*
- *	IDE subdriver functions, registered with ide.c
- */
+static void idetape_attach(struct ata_device *);
+
 static struct ata_operations idetape_driver = {
 	owner:			THIS_MODULE,
+	attach:			idetape_attach,
 	cleanup:		idetape_cleanup,
 	standby:		NULL,
 	do_request:		idetape_do_request,
@@ -6070,6 +6066,8 @@ static struct ata_operations idetape_driver = {
 	revalidate:		idetape_revalidate,
 };
 
+
+
 /*
  *	Our character device supporting functions, passed to register_chrdev.
  */
@@ -6082,104 +6080,93 @@ static struct file_operations idetape_fops = {
 	release:	idetape_chrdev_release,
 };
 
-MODULE_DESCRIPTION("ATAPI Streaming TAPE Driver");
-MODULE_LICENSE("GPL");
-
-static void __exit idetape_exit(void)
+static void idetape_attach(struct ata_device *drive)
 {
-	struct ata_device *drive;
-	int minor;
+	idetape_tape_t *tape;
+	int minor, supported = 0;
+	char *req;
+	struct ata_channel *channel;
+	int unit;
 
-	for (minor = 0; minor < MAX_HWIFS * MAX_DRIVES; minor++) {
-		drive = idetape_chrdevs[minor].drive;
-		if (drive != NULL && idetape_cleanup (drive))
-		printk (KERN_ERR "ide-tape: %s: cleanup_module() called while still busy\n", drive->name);
-	}
-}
+	if (drive->type != ATA_TAPE)
+		return;
+
+	req = drive->driver_req;
+	if (req[0] != '\0' && strcmp(req, "ide-tape"))
+		return;
 
-/*
- *	idetape_init will register the driver for each tape.
- */
-int idetape_init(void)
-{
-	struct ata_device *drive;
-	idetape_tape_t *tape;
-	int minor, failed = 0, supported = 0;
-/* DRIVER(drive)->busy++; */
-	MOD_INC_USE_COUNT;
-#if ONSTREAM_DEBUG
-        printk(KERN_INFO "ide-tape: MOD_INC_USE_COUNT in idetape_init\n");
-#endif
 	if (!idetape_chrdev_present)
 		for (minor = 0; minor < MAX_HWIFS * MAX_DRIVES; minor++ )
 			idetape_chrdevs[minor].drive = NULL;
 
-	if ((drive = ide_scan_devices(ATA_TAPE, "ide-tape", NULL, failed++)) == NULL) {
-		revalidate_drives();
-		MOD_DEC_USE_COUNT;
-#if ONSTREAM_DEBUG
-		printk(KERN_INFO "ide-tape: MOD_DEC_USE_COUNT in idetape_init\n");
-#endif
-		return 0;
-	}
 	if (!idetape_chrdev_present &&
 	    devfs_register_chrdev (IDETAPE_MAJOR, "ht", &idetape_fops)) {
-		printk (KERN_ERR "ide-tape: Failed to register character device interface\n");
-		MOD_DEC_USE_COUNT;
-#if ONSTREAM_DEBUG
-		printk(KERN_INFO "ide-tape: MOD_DEC_USE_COUNT in idetape_init\n");
-#endif
-		return -EBUSY;
+		printk(KERN_ERR "ide-tape: Failed to register character device interface\n");
+		return;
 	}
-	do {
-		if (!idetape_identify_device (drive, drive->id)) {
-			printk (KERN_ERR "ide-tape: %s: not supported by this version of ide-tape\n", drive->name);
-			continue;
-		}
-		if (drive->scsi) {
-			if (strstr(drive->id->model, "OnStream DI-")) {
-				printk("ide-tape: ide-scsi emulation is not supported for %s.\n", drive->id->model);
-			} else {
-				printk("ide-tape: passing drive %s to ide-scsi emulation.\n", drive->name);
-				continue;
-			}
-		}
-		tape = (idetape_tape_t *) kmalloc (sizeof (idetape_tape_t), GFP_KERNEL);
-		if (tape == NULL) {
-			printk (KERN_ERR "ide-tape: %s: Can't allocate a tape structure\n", drive->name);
-			continue;
-		}
-		if (ide_register_subdriver (drive, &idetape_driver)) {
-			printk (KERN_ERR "ide-tape: %s: Failed to register the driver with ide.c\n", drive->name);
-			kfree (tape);
-			continue;
+
+	if (!idetape_identify_device (drive, drive->id)) {
+		printk(KERN_ERR "ide-tape: %s: not supported by this version of ide-tape\n", drive->name);
+		return;
+	}
+	if (drive->scsi) {
+		if (strstr(drive->id->model, "OnStream DI-")) {
+			printk(KERN_INFO "ide-tape: ide-scsi emulation is not supported for %s.\n", drive->id->model);
+		} else {
+			printk(KERN_INFO "ide-tape: passing drive %s to ide-scsi emulation.\n", drive->name);
+			return;
 		}
-		for (minor = 0; idetape_chrdevs[minor].drive != NULL; minor++);
-		idetape_setup (drive, tape, minor);
-		idetape_chrdevs[minor].drive = drive;
-		tape->de_r =
-		    devfs_register (drive->de, "mt", DEVFS_FL_DEFAULT,
-				    drive->channel->major, minor,
-				    S_IFCHR | S_IRUGO | S_IWUGO,
-				    &idetape_fops, NULL);
-		tape->de_n =
-		    devfs_register (drive->de, "mtn", DEVFS_FL_DEFAULT,
-				    drive->channel->major, minor + 128,
-				    S_IFCHR | S_IRUGO | S_IWUGO,
-				    &idetape_fops, NULL);
-		devfs_register_tape (tape->de_r);
-		supported++; failed--;
-	} while ((drive = ide_scan_devices(ATA_TAPE, "ide-tape", NULL, failed++)) != NULL);
+	}
+	tape = (idetape_tape_t *) kmalloc (sizeof (idetape_tape_t), GFP_KERNEL);
+	if (!tape) {
+		printk (KERN_ERR "ide-tape: %s: Can't allocate a tape structure\n", drive->name);
+		return;
+	}
+	if (ide_register_subdriver (drive, &idetape_driver)) {
+		printk (KERN_ERR "ide-tape: %s: Failed to register the driver with ide.c\n", drive->name);
+		kfree (tape);
+		return;
+	}
+	for (minor = 0; idetape_chrdevs[minor].drive != NULL; minor++);
+	idetape_setup (drive, tape, minor);
+	idetape_chrdevs[minor].drive = drive;
+	tape->de_r =
+		devfs_register (drive->de, "mt", DEVFS_FL_DEFAULT,
+				drive->channel->major, minor,
+				S_IFCHR | S_IRUGO | S_IWUGO,
+				&idetape_fops, NULL);
+	tape->de_n =
+		devfs_register (drive->de, "mtn", DEVFS_FL_DEFAULT,
+				drive->channel->major, minor + 128,
+				S_IFCHR | S_IRUGO | S_IWUGO,
+				&idetape_fops, NULL);
+	devfs_register_tape (tape->de_r);
+	supported++;
+
 	if (!idetape_chrdev_present && !supported) {
 		devfs_unregister_chrdev (IDETAPE_MAJOR, "ht");
 	} else
 		idetape_chrdev_present = 1;
-	revalidate_drives();
-	MOD_DEC_USE_COUNT;
-#if ONSTREAM_DEBUG
-	printk(KERN_INFO "ide-tape: MOD_DEC_USE_COUNT in idetape_init\n");
-#endif
-	return 0;
+
+	/* Feel free to use partitions even on tapes... */
+
+	channel = drive->channel;
+	unit = drive - channel->drives;
+
+	ide_revalidate_disk(mk_kdev(channel->major, unit << PARTN_BITS));
+}
+
+MODULE_DESCRIPTION("ATAPI Streaming TAPE Driver");
+MODULE_LICENSE("GPL");
+
+static void __exit idetape_exit(void)
+{
+	unregister_ata_driver(&idetape_driver);
+}
+
+int __init idetape_init(void)
+{
+	return ata_driver_module(&idetape_driver);
 }
 
 module_init(idetape_init);

drivers/ide/it8172.c

@@ -48,17 +48,17 @@
 /*
  * Prototypes
  */
-static void it8172_tune_drive (ide_drive_t *drive, byte pio);
+static void it8172_tune_drive (struct ata_device *drive, byte pio);
 #if defined(CONFIG_BLK_DEV_IDEDMA) && defined(CONFIG_IT8172_TUNING)
 static byte it8172_dma_2_pio (byte xfer_rate);
-static int it8172_tune_chipset (ide_drive_t *drive, byte speed);
-static int it8172_config_chipset_for_dma (ide_drive_t *drive);
-static int it8172_dmaproc(ide_dma_action_t func, ide_drive_t *drive);
+static int it8172_tune_chipset (struct ata_device *drive, byte speed);
+static int it8172_config_chipset_for_dma (struct ata_device *drive);
+static int it8172_dmaproc(ide_dma_action_t func, struct ata_device *drive);
 #endif
 void __init ide_init_it8172(struct ata_channel *channel);
 
 
-static void it8172_tune_drive (ide_drive_t *drive, byte pio)
+static void it8172_tune_drive (struct ata_device *drive, byte pio)
 {
     unsigned long flags;
     u16 drive_enables;
@@ -139,7 +139,7 @@ static byte it8172_dma_2_pio (byte xfer_rate)
     }
 }
 
-static int it8172_tune_chipset (ide_drive_t *drive, byte speed)
+static int it8172_tune_chipset (struct ata_device *drive, byte speed)
 {
     struct ata_channel *hwif = drive->channel;
     struct pci_dev *dev	= hwif->pci_dev;
@@ -194,7 +194,7 @@ static int it8172_tune_chipset (ide_drive_t *drive, byte speed)
     return err;
 }
 
-static int it8172_config_chipset_for_dma(ide_drive_t *drive)
+static int it8172_config_chipset_for_dma(struct ata_device *drive)
 {
     struct hd_driveid *id = drive->id;
     byte speed;
@@ -210,7 +210,7 @@ static int it8172_config_chipset_for_dma(ide_drive_t *drive)
 	    ide_dma_off_quietly);
 }
 
-static int it8172_dmaproc(ide_dma_action_t func, ide_drive_t *drive)
+static int it8172_dmaproc(ide_dma_action_t func, struct ata_device *drive)
 {
     switch (func) {
     case ide_dma_check:

drivers/ide/macide.c

@@ -119,7 +119,7 @@ void macide_init(void)
 			/* hardware ID, and we cna't get that without	*/
 			/* probing the drive which freezes a 190.	*/
 
-			ide_drive_t *drive = &ide_hwifs[index].drives[0];
+			struct ata_device *drive = &ide_hwifs[index].drives[0];
         		drive->capacity = drive->cyl*drive->head*drive->sect;
 
 #ifdef CONFIG_BLK_DEV_MAC_MEDIABAY

drivers/ide/ns87415.c

@@ -33,7 +33,7 @@ static unsigned int ns87415_count = 0, ns87415_control[MAX_HWIFS] = { 0 };
  * the IRQ associated with the port (drive->channel),
  * and selects either PIO or DMA handshaking for the next I/O operation.
  */
-static void ns87415_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
+static void ns87415_prepare_drive(struct ata_device *drive, unsigned int use_dma)
 {
 	struct ata_channel *hwif = drive->channel;
 	unsigned int bit, other, new, *old = (unsigned int *) hwif->select_data;
@@ -78,7 +78,7 @@ static void ns87415_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
 	__restore_flags(flags);	/* local CPU only */
 }
 
-static void ns87415_selectproc (ide_drive_t *drive)
+static void ns87415_selectproc(struct ata_device *drive)
 {
 	ns87415_prepare_drive (drive, drive->using_dma);
 }

drivers/ide/opti621.c

@@ -137,7 +137,7 @@ int reg_base;
 
 /* there are stored pio numbers from other calls of opti621_tune_drive */
 
-static void compute_pios(ide_drive_t *drive, byte pio)
+static void compute_pios(struct ata_device *drive, byte pio)
 /* Store values into drive->drive_data
  *	second_contr - 0 for primary controller, 1 for secondary
  *	slave_drive - 0 -> pio is for master, 1 -> pio is for slave
@@ -245,7 +245,7 @@ static void compute_clocks(int pio, pio_clocks_t *clks)
 }
 
 /* Main tune procedure, called from tuneproc. */
-static void opti621_tune_drive (ide_drive_t *drive, byte pio)
+static void opti621_tune_drive(struct ata_device *drive, byte pio)
 {
 	/* primary and secondary drives share some registers,
 	 * so we have to program both drives

drivers/ide/pdcraid.c

@@ -377,7 +377,7 @@ static int pdcraid1_make_request (request_queue_t *q, int rw, struct buffer_head
 static unsigned long calc_pdcblock_offset(struct block_device *bdev)
 {
 	unsigned long lba = 0;
-	ide_drive_t *ideinfo = get_info_ptr(to_kdev_t(bdev->bd_dev));
+	struct ata_device *ideinfo = get_info_ptr(to_kdev_t(bdev->bd_dev));
 
 	if (ideinfo==NULL)
 		return 0;

drivers/ide/qd65xx.c

@@ -112,7 +112,7 @@ byte __init qd_read_reg (byte reg)
  * This routine is invoked from ide.c to prepare for access to a given drive.
  */
 
-static void qd_select (ide_drive_t *drive)
+static void qd_select(struct ata_device *drive)
 {
 	byte index = (( (QD_TIMREG(drive)) & 0x80 ) >> 7) |
 			(QD_TIMREG(drive) & 0x02);
@@ -164,7 +164,7 @@ static byte qd6580_compute_timing (int active_time, int recovery_time)
  * tries to find timing from dos driver's table
  */
 
-static int qd_find_disk_type (ide_drive_t *drive,
+static int qd_find_disk_type(struct ata_device *drive,
 		int *active_time, int *recovery_time)
 {
 	struct qd65xx_timing_s *p;
@@ -192,7 +192,7 @@ static int qd_find_disk_type (ide_drive_t *drive,
  * check whether timings don't conflict
  */
 
-static int qd_timing_ok (ide_drive_t drives[])
+static int qd_timing_ok(struct ata_device drives[])
 {
 	return (IDE_IMPLY(drives[0].present && drives[1].present,
 			IDE_IMPLY(QD_TIMREG(drives) == QD_TIMREG(drives+1),
@@ -206,7 +206,7 @@ static int qd_timing_ok (ide_drive_t drives[])
  * records the timing, and enables selectproc as needed
  */
 
-static void qd_set_timing (ide_drive_t *drive, byte timing)
+static void qd_set_timing(struct ata_device *drive, byte timing)
 {
 	struct ata_channel *hwif = drive->channel;
 
@@ -225,7 +225,7 @@ static void qd_set_timing (ide_drive_t *drive, byte timing)
  * qd6500_tune_drive
  */
 
-static void qd6500_tune_drive (ide_drive_t *drive, byte pio)
+static void qd6500_tune_drive(struct ata_device *drive, byte pio)
 {
 	int active_time   = 175;
 	int recovery_time = 415; /* worst case values from the dos driver */
@@ -247,7 +247,7 @@ static void qd6500_tune_drive (ide_drive_t *drive, byte pio)
  * qd6580_tune_drive
  */
 
-static void qd6580_tune_drive (ide_drive_t *drive, byte pio)
+static void qd6580_tune_drive(struct ata_device *drive, byte pio)
 {
 	struct ata_timing *t;
 	int base = drive->channel->select_data;

drivers/ide/serverworks.c

@@ -240,6 +240,26 @@ extern char *ide_xfer_verbose (byte xfer_rate);
 
 static struct pci_dev *isa_dev;
 
+static int svwks_ratemask(struct ata_device *drive)
+{
+	struct pci_dev *dev = drive->channel->pci_dev;
+	int map = 0;
+
+	if (!eighty_ninty_three(drive))
+		return XFER_UDMA;
+
+	switch(dev->device) {
+		case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
+			if (svwks_revision >= SVWKS_CSB5_REVISION_NEW)
+				map |= XFER_UDMA_100;
+			map |= XFER_UDMA_66;
+		case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
+			map |= XFER_UDMA;
+			break;
+	}
+	return map;
+}
+
 static int svwks_tune_chipset(struct ata_device *drive, byte speed)
 {
 	static u8 udma_modes[]	= { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
@@ -251,11 +271,6 @@ static int svwks_tune_chipset(struct ata_device *drive, byte speed)
 	byte unit		= (drive->select.b.unit & 0x01);
 	byte csb5		= (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ? 1 : 0;
 
-#ifdef CONFIG_BLK_DEV_IDEDMA
-	unsigned long dma_base	= hwif->dma_base;
-#endif
-	int err;
-
 	byte drive_pci		= 0x00;
 	byte drive_pci2		= 0x00;
 	byte drive_pci3		= hwif->unit ? 0x57 : 0x56;
@@ -338,9 +353,6 @@ static int svwks_tune_chipset(struct ata_device *drive, byte speed)
 	printk("%s: %s drive%d\n", drive->name, ide_xfer_verbose(speed), drive->dn);
 #endif /* SVWKS_DEBUG_DRIVE_INFO */
 
-	if (!drive->init_speed)
-		drive->init_speed = speed;
-
 	pci_write_config_byte(dev, drive_pci, pio_timing);
 	if (csb5)
 		pci_write_config_word(dev, 0x4A, csb5_pio);
@@ -349,16 +361,12 @@ static int svwks_tune_chipset(struct ata_device *drive, byte speed)
 	pci_write_config_byte(dev, drive_pci2, dma_timing);
 	pci_write_config_byte(dev, drive_pci3, ultra_timing);
 	pci_write_config_byte(dev, 0x54, ultra_enable);
-
-	if (speed > XFER_PIO_4)
-		outb(inb(dma_base+2)|(1<<(5+unit)), dma_base+2);
-	else
-		outb(inb(dma_base+2) & ~(1<<(5+unit)), dma_base+2);
-#endif /* CONFIG_BLK_DEV_IDEDMA */
-
-	err = ide_config_drive_speed(drive, speed);
+#endif
+	if (!drive->init_speed)
+		drive->init_speed = speed;
 	drive->current_speed = speed;
-	return err;
+
+	return ide_config_drive_speed(drive, speed);
 }
 
 static void config_chipset_for_pio(struct ata_device *drive)
@@ -415,23 +423,14 @@ static void svwks_tune_drive(struct ata_device *drive, byte pio)
 #ifdef CONFIG_BLK_DEV_IDEDMA
 static int config_chipset_for_dma(struct ata_device *drive)
 {
-	struct hd_driveid *id	= drive->id;
-	struct pci_dev *dev	= drive->channel->pci_dev;
-	byte udma_66	= eighty_ninty_three(drive);
-	int ultra66	= (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ? 1 : 0;
-	int ultra100	= (ultra66 && svwks_revision >= SVWKS_CSB5_REVISION_NEW) ? 1 : 0;
-
-	byte speed = ata_timing_mode(drive, XFER_PIO | XFER_EPIO | XFER_SWDMA | XFER_MWDMA | XFER_UDMA
-				| ((udma_66 && ultra66) ? XFER_UDMA_66 : 0)
-				| ((udma_66 && ultra100) ? XFER_UDMA_100 : 0));
+	int map;
+	byte mode;
 
-	(void) svwks_tune_chipset(drive, speed);
+	/* FIXME: check SWDMA modes --bkz */
+	map = XFER_MWDMA | svwks_ratemask(drive);
+	mode = ata_timing_mode(drive, map);
 
-	return ((int)	((id->dma_ultra >> 11) & 7) ? 1 :
-			((id->dma_ultra >> 8) & 7) ? 1 :
-			((id->dma_mword >> 8) & 7) ? 1 :
-			((id->dma_1word >> 8) & 7) ? 1 :
-						     0);
+	return !svwks_tune_chipset(drive, mode);
 }
 
 static int config_drive_xfer_rate(struct ata_device *drive)

drivers/ide/sl82c105.c

@@ -71,7 +71,7 @@ static unsigned int get_timing_sl82c105(struct ata_timing *t)
 /*
  * Configure the drive and chipset for PIO
  */
-static void config_for_pio(ide_drive_t *drive, int pio, int report)
+static void config_for_pio(struct ata_device *drive, int pio, int report)
 {
 	struct ata_channel *hwif = drive->channel;
 	struct pci_dev *dev = hwif->pci_dev;
@@ -109,7 +109,7 @@ static void config_for_pio(ide_drive_t *drive, int pio, int report)
 /*
  * Configure the drive and the chipset for DMA
  */
-static int config_for_dma(ide_drive_t *drive)
+static int config_for_dma(struct ata_device *drive)
 {
 	struct ata_channel *hwif = drive->channel;
 	struct pci_dev *dev = hwif->pci_dev;
@@ -131,7 +131,7 @@ static int config_for_dma(ide_drive_t *drive)
  * Check to see if the drive and
  * chipset is capable of DMA mode
  */
-static int sl82c105_check_drive(ide_drive_t *drive)
+static int sl82c105_check_drive(struct ata_device *drive)
 {
 	int on = 0;
 
@@ -240,7 +240,7 @@ static void sl82c105_timeout(struct ata_device *drive)
  * This function is called when the IDE timer expires, the drive
  * indicates that it is READY, and we were waiting for DMA to complete.
  */
-static void sl82c105_lostirq(ide_drive_t *drive)
+static void sl82c105_lostirq(struct ata_device *drive)
 {
 	struct ata_channel *ch = drive->channel;
 	struct pci_dev *dev = ch->pci_dev;
@@ -273,7 +273,7 @@ static void sl82c105_lostirq(ide_drive_t *drive)
  * We only deal with PIO mode here - DMA mode 'using_dma' is not
  * initialised at the point that this function is called.
  */
-static void tune_sl82c105(ide_drive_t *drive, byte pio)
+static void tune_sl82c105(struct ata_device *drive, byte pio)
 {
 	config_for_pio(drive, pio, 1);
 

drivers/scsi/ide-scsi.c

@@ -502,11 +502,14 @@ static void idescsi_revalidate(struct ata_device *_dummy)
 	 */
 }
 
+static void idescsi_attach(struct ata_device *drive);
+
 /*
  *	IDE subdriver functions, registered with ide.c
  */
 static struct ata_operations idescsi_driver = {
 	owner:			THIS_MODULE,
+	attach:			idescsi_attach,
 	cleanup:		idescsi_cleanup,
 	standby:		NULL,
 	do_request:		idescsi_do_request,
@@ -519,45 +522,40 @@ static struct ata_operations idescsi_driver = {
 	capacity:		NULL,
 };
 
-/*
- *	idescsi_init will register the driver for each scsi.
- */
-int idescsi_init(void)
+static void idescsi_attach(struct ata_device *drive)
 {
-	struct ata_device *drive;
 	idescsi_scsi_t *scsi;
-	/* FIXME: The following is just plain wrong, since those are definitely *not* the
-	 * media types supported by the ATA layer */
-	byte media[] = {TYPE_DISK, TYPE_TAPE, TYPE_PROCESSOR, TYPE_WORM, TYPE_ROM, TYPE_SCANNER, TYPE_MOD, 255};
-	int i, failed, id;
+	int i, id;
+	char *req;
+	struct ata_channel *channel;
+	int unit;
 
 	if (idescsi_initialized)
-		return 0;
+		return;
 	idescsi_initialized = 1;
 	for (i = 0; i < MAX_HWIFS * MAX_DRIVES; i++)
 		idescsi_drives[i] = NULL;
-	MOD_INC_USE_COUNT;
-	for (i = 0; media[i] != 255; i++) {
-		failed = 0;
-		while ((drive = ide_scan_devices (media[i], "ide-scsi", NULL, failed++)) != NULL) {
 
-			if ((scsi = (idescsi_scsi_t *) kmalloc (sizeof (idescsi_scsi_t), GFP_KERNEL)) == NULL) {
-				printk (KERN_ERR "ide-scsi: %s: Can't allocate a scsi structure\n", drive->name);
-				continue;
-			}
-			if (ide_register_subdriver (drive, &idescsi_driver)) {
-				printk (KERN_ERR "ide-scsi: %s: Failed to register the driver with ide.c\n", drive->name);
-				kfree (scsi);
-				continue;
-			}
-			for (id = 0; id < MAX_HWIFS * MAX_DRIVES && idescsi_drives[id]; id++);
-				idescsi_setup (drive, scsi, id);
-			failed--;
-		}
+	req = drive->driver_req;
+	if (req[0] != '\0' && strcmp(req, "ide-scsi"))
+		return;
+
+	if ((scsi = (idescsi_scsi_t *) kmalloc (sizeof (idescsi_scsi_t), GFP_KERNEL)) == NULL) {
+		printk(KERN_ERR "ide-scsi: %s: Can't allocate a scsi structure\n", drive->name);
+		return;
 	}
-	revalidate_drives();
-	MOD_DEC_USE_COUNT;
-	return 0;
+	if (ide_register_subdriver (drive, &idescsi_driver)) {
+		printk(KERN_ERR "ide-scsi: %s: Failed to register the driver with ide.c\n", drive->name);
+		kfree (scsi);
+		return;
+	}
+	for (id = 0; id < MAX_HWIFS * MAX_DRIVES && idescsi_drives[id]; id++);
+	idescsi_setup (drive, scsi, id);
+
+	channel = drive->channel;
+	unit = drive - channel->drives;
+
+	ide_revalidate_disk(mk_kdev(channel->major, unit << PARTN_BITS));
 }
 
 int idescsi_detect (Scsi_Host_Template *host_template)
@@ -805,38 +803,31 @@ static Scsi_Host_Template idescsi_template = {
 	emulated:	1,
 };
 
-static int __init init_idescsi_module(void)
+
+static int __init idescsi_init(void)
 {
-	idescsi_init();
+	int ret;
+	ret = ata_driver_module(&idescsi_driver);
 	scsi_register_host(&idescsi_template);
 	return 0;
 }
 
 static void __exit exit_idescsi_module(void)
 {
-	struct ata_device *drive;
-	byte media[] = {TYPE_DISK, TYPE_TAPE, TYPE_PROCESSOR, TYPE_WORM, TYPE_ROM, TYPE_SCANNER, TYPE_MOD, 255};
-	int i, failed;
-
 	scsi_unregister_host(&idescsi_template);
 
-	/* FIXME: The media types scanned here have literally nothing to do
-	 * with the media types used by the overall ATA code!
-	 *
-	 * This is basically showing us, that there is something wrong with the
-	 * ide_scan_devices function.
-	 */
+#if 0
+	/* FIXME: what about this cleanup stuff here? This all should be done
+	 * on close time perhaps? */
 
-	for (i = 0; media[i] != 255; i++) {
-		failed = 0;
-		while ((drive = ide_scan_devices (media[i], "ide-scsi", &idescsi_driver, failed)) != NULL)
-			if (idescsi_cleanup (drive)) {
-				printk ("%s: exit_idescsi_module() called while still busy\n", drive->name);
-				failed++;
-			}
+	if (idescsi_cleanup (drive)) {
+		printk ("%s: exit_idescsi_module() called while still busy\n", drive->name);
 	}
+#endif
+
+	unregister_ata_driver(&idescsi_driver);
 }
 
-module_init(init_idescsi_module);
+module_init(idescsi_init);
 module_exit(exit_idescsi_module);
 MODULE_LICENSE("GPL");

include/linux/ide.h

@@ -317,7 +317,6 @@ typedef union {
 /*
  * ATA/ATAPI device structure :
  */
-typedef
 struct ata_device {
 	struct ata_channel *	channel;
 	char			name[6];	/* device name */
@@ -409,7 +408,7 @@ struct ata_device {
 	unsigned long	immed_comp;
 	int		max_last_depth;
 	int		max_depth;
-} ide_drive_t;
+};
 
 /*
  * Status returned by various functions.
@@ -590,6 +589,7 @@ static inline int ata_can_queue(struct ata_device *drive)
 
 struct ata_operations {
 	struct module *owner;
+	void (*attach) (struct ata_device *);
 	int (*cleanup)(struct ata_device *);
 	int (*standby)(struct ata_device *);
 	ide_startstop_t	(*do_request)(struct ata_device *, struct request *, sector_t);
@@ -602,6 +602,9 @@ struct ata_operations {
 	void (*revalidate)(struct ata_device *);
 
 	sector_t (*capacity)(struct ata_device *);
+
+	/* linked list of rgistered device type drivers */
+	struct ata_operations *next;
 };
 
 /* Alas, no aliases. Too much hassle with bringing module.h everywhere */
@@ -618,11 +621,20 @@ do {	\
 
 extern sector_t ata_capacity(struct ata_device *drive);
 
-/* FIXME: Actually implement and use them as soon as possible!  to make the
- * ide_scan_devices() go away! */
-
-extern int unregister_ata_driver(unsigned int type, struct ata_operations *driver);
-extern int register_ata_driver(unsigned int type, struct ata_operations *driver);
+extern void unregister_ata_driver(struct ata_operations *driver);
+extern int register_ata_driver(struct ata_operations *driver);
+static inline int ata_driver_module(struct ata_operations *driver)
+{
+#ifdef MODULE
+	if (register_ata_driver(driver) <= 0) {
+		unregister_ata_driver(driver);
+		return -ENODEV;
+	}
+#else
+	register_ata_driver(driver);
+#endif
+	return 0;
+}
 
 #define ata_ops(drive)		((drive)->driver)
 
@@ -797,9 +809,9 @@ extern int idefloppy_init (void);
 extern int idescsi_init (void);
 #endif
 
-extern struct ata_device *ide_scan_devices(byte, const char *, struct ata_operations *, int);
 extern int ide_register_subdriver(struct ata_device *, struct ata_operations *);
 extern int ide_unregister_subdriver(struct ata_device *drive);
+extern int ide_revalidate_disk(kdev_t i_rdev);
 
 #ifdef CONFIG_PCI
 # define ON_BOARD		0
@@ -890,6 +902,5 @@ extern spinlock_t ide_lock;
 #define DRIVE_LOCK(drive)		((drive)->queue.queue_lock)
 
 extern int drive_is_ready(struct ata_device *drive);
-extern void revalidate_drives(void);
 
 #endif