Commit 14615ecc authored by John David Anglin's avatar John David Anglin Committed by Helge Deller

parisc: Simplify fast path for non-access data TLB faults

With the latest cache fix for non-access faults and the support for
non-access faults (code 17) in handle_interruption, we can remove
the fast path emulation for fdc, fic, pdc, lpa, probe and probei
instructions.
Signed-off-by: default avatarJohn David Anglin <dave.anglin@bell.net>
Signed-off-by: default avatarHelge Deller <deller@gmx.de>
parent e00b0a2a
......@@ -1288,74 +1288,12 @@ nadtlb_check_alias_20:
nadtlb_emulate:
/*
* Non access misses can be caused by fdc,fic,pdc,lpa,probe and
* probei instructions. We don't want to fault for these
* instructions (not only does it not make sense, it can cause
* deadlocks, since some flushes are done with the mmap
* semaphore held). If the translation doesn't exist, we can't
* insert a translation, so have to emulate the side effects
* of the instruction. Since we don't insert a translation
* we can get a lot of faults during a flush loop, so it makes
* sense to try to do it here with minimum overhead. We only
* emulate fdc,fic,pdc,probew,prober instructions whose base
* and index registers are not shadowed. We defer everything
* else to the "slow" path.
* Non-access misses can be caused by fdc,fic,pdc,lpa,probe and
* probei instructions. The kernel no longer faults doing flushes.
* Use of lpa and probe instructions is rare. Given the issue
* with shadow registers, we defer everything to the "slow" path.
*/
mfctl %cr19,%r9 /* Get iir */
/* PA 2.0 Arch Ref. Book pg 382 has a good description of the insn bits.
Checks for fdc,fdce,pdc,"fic,4f",prober,probeir,probew, probeiw */
/* Checks for fdc,fdce,pdc,"fic,4f" only */
ldi 0x280,%r16
and %r9,%r16,%r17
cmpb,<>,n %r16,%r17,nadtlb_probe_check
bb,>=,n %r9,26,nadtlb_nullify /* m bit not set, just nullify */
BL get_register,%r25
extrw,u %r9,15,5,%r8 /* Get index register # */
cmpib,COND(=),n -1,%r1,nadtlb_fault /* have to use slow path */
copy %r1,%r24
BL get_register,%r25
extrw,u %r9,10,5,%r8 /* Get base register # */
cmpib,COND(=),n -1,%r1,nadtlb_fault /* have to use slow path */
BL set_register,%r25
add,l %r1,%r24,%r1 /* doesn't affect c/b bits */
nadtlb_nullify:
mfctl %ipsw,%r8
ldil L%PSW_N,%r9
or %r8,%r9,%r8 /* Set PSW_N */
mtctl %r8,%ipsw
rfir
nop
/*
When there is no translation for the probe address then we
must nullify the insn and return zero in the target register.
This will indicate to the calling code that it does not have
write/read privileges to this address.
This should technically work for prober and probew in PA 1.1,
and also probe,r and probe,w in PA 2.0
WARNING: USE ONLY NON-SHADOW REGISTERS WITH PROBE INSN!
THE SLOW-PATH EMULATION HAS NOT BEEN WRITTEN YET.
*/
nadtlb_probe_check:
ldi 0x80,%r16
and %r9,%r16,%r17
cmpb,<>,n %r16,%r17,nadtlb_fault /* Must be probe,[rw]*/
BL get_register,%r25 /* Find the target register */
extrw,u %r9,31,5,%r8 /* Get target register */
cmpib,COND(=),n -1,%r1,nadtlb_fault /* have to use slow path */
BL set_register,%r25
copy %r0,%r1 /* Write zero to target register */
b nadtlb_nullify /* Nullify return insn */
nop
b,n nadtlb_fault
#ifdef CONFIG_64BIT
itlb_miss_20w:
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment