Merge remote-tracking branches 'spi/topic/loopback', 'spi/topic/meson-spicc',...

Merge remote-tracking branches 'spi/topic/loopback', 'spi/topic/meson-spicc', 'spi/topic/mtk' and 'spi/topic/omap2-mcspi' into spi-next

Documentation/devicetree/bindings/spi/spi-meson.txt

@@ -20,3 +20,34 @@ Required properties:
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
+
+* SPICC (SPI Communication Controller)
+
+The Meson SPICC is generic SPI controller for general purpose Full-Duplex
+communications with dedicated 16 words RX/TX PIO FIFOs.
+
+Required properties:
+ - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs.
+ - reg: physical base address and length of the controller registers
+ - interrupts: The interrupt specifier
+ - clock-names: Must contain "core"
+ - clocks: phandle of the input clock for the baud rate generator
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+Optional properties:
+ - resets: phandle of the internal reset line
+
+See ../spi/spi-bus.txt for more details on SPI bus master and slave devices
+required and optional properties.
+
+Example :
+	spi@c1108d80 {
+		compatible = "amlogic,meson-gx-spicc";
+		reg = <0xc1108d80 0x80>;
+		interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "core";
+		clocks = <&clk81>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -3,7 +3,9 @@ Binding for MTK SPI controller
 Required properties:
 - compatible: should be one of the following.
     - mediatek,mt2701-spi: for mt2701 platforms
+    - mediatek,mt2712-spi: for mt2712 platforms
     - mediatek,mt6589-spi: for mt6589 platforms
+    - mediatek,mt7622-spi: for mt7622 platforms
     - mediatek,mt8135-spi: for mt8135 platforms
     - mediatek,mt8173-spi: for mt8173 platforms
 

drivers/spi/Kconfig

@@ -393,6 +393,13 @@ config SPI_FSL_ESPI
 	  From MPC8536, 85xx platform uses the controller, and all P10xx,
 	  P20xx, P30xx,P40xx, P50xx uses this controller.
 
+config SPI_MESON_SPICC
+	tristate "Amlogic Meson SPICC controller"
+	depends on ARCH_MESON || COMPILE_TEST
+	help
+	  This enables master mode support for the SPICC (SPI communication
+	  controller) available in Amlogic Meson SoCs.
+
 config SPI_MESON_SPIFC
 	tristate "Amlogic Meson SPIFC controller"
 	depends on ARCH_MESON || COMPILE_TEST

drivers/spi/Makefile

@@ -53,6 +53,7 @@ obj-$(CONFIG_SPI_LANTIQ_SSC)		+= spi-lantiq-ssc.o
 obj-$(CONFIG_SPI_JCORE)			+= spi-jcore.o
 obj-$(CONFIG_SPI_LM70_LLP)		+= spi-lm70llp.o
 obj-$(CONFIG_SPI_LP8841_RTC)		+= spi-lp8841-rtc.o
+obj-$(CONFIG_SPI_MESON_SPICC)		+= spi-meson-spicc.o
 obj-$(CONFIG_SPI_MESON_SPIFC)		+= spi-meson-spifc.o
 obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mpc512x-psc.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mpc52xx-psc.o

drivers/spi/spi-loopback-test.c

@@ -894,7 +894,7 @@ int spi_test_execute_msg(struct spi_device *spi, struct spi_test *test,
 		test->elapsed_time = ktime_to_ns(ktime_sub(ktime_get(), start));
 		if (ret == -ETIMEDOUT) {
 			dev_info(&spi->dev,
-				 "spi-message timed out - reruning...\n");
+				 "spi-message timed out - rerunning...\n");
 			/* rerun after a few explicit schedules */
 			for (i = 0; i < 16; i++)
 				schedule();
@@ -1021,10 +1021,9 @@ int spi_test_run_tests(struct spi_device *spi,
 		rx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
 	else
 		rx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
-	if (!rx) {
-		ret = -ENOMEM;
-		goto out;
-	}
+	if (!rx)
+		return -ENOMEM;
+
 
 	if (use_vmalloc)
 		tx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
@@ -1032,7 +1031,7 @@ int spi_test_run_tests(struct spi_device *spi,
 		tx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
 	if (!tx) {
 		ret = -ENOMEM;
-		goto out;
+		goto err_tx;
 	}
 
 	/* now run the individual tests in the table */
@@ -1057,8 +1056,9 @@ int spi_test_run_tests(struct spi_device *spi,
 	}
 
 out:
-	kvfree(rx);
 	kvfree(tx);
+err_tx:
+	kvfree(rx);
 	return ret;
 }
 EXPORT_SYMBOL_GPL(spi_test_run_tests);

drivers/spi/spi-mt65xx.c

@@ -35,11 +35,15 @@
 #define SPI_CMD_REG                       0x0018
 #define SPI_STATUS0_REG                   0x001c
 #define SPI_PAD_SEL_REG                   0x0024
+#define SPI_CFG2_REG                      0x0028
 
 #define SPI_CFG0_SCK_HIGH_OFFSET          0
 #define SPI_CFG0_SCK_LOW_OFFSET           8
 #define SPI_CFG0_CS_HOLD_OFFSET           16
 #define SPI_CFG0_CS_SETUP_OFFSET          24
+#define SPI_ADJUST_CFG0_SCK_LOW_OFFSET    16
+#define SPI_ADJUST_CFG0_CS_HOLD_OFFSET    0
+#define SPI_ADJUST_CFG0_CS_SETUP_OFFSET   16
 
 #define SPI_CFG1_CS_IDLE_OFFSET           0
 #define SPI_CFG1_PACKET_LOOP_OFFSET       8
@@ -55,6 +59,8 @@
 #define SPI_CMD_RST                  BIT(2)
 #define SPI_CMD_PAUSE_EN             BIT(4)
 #define SPI_CMD_DEASSERT             BIT(5)
+#define SPI_CMD_SAMPLE_SEL           BIT(6)
+#define SPI_CMD_CS_POL               BIT(7)
 #define SPI_CMD_CPHA                 BIT(8)
 #define SPI_CMD_CPOL                 BIT(9)
 #define SPI_CMD_RX_DMA               BIT(10)
@@ -80,6 +86,8 @@ struct mtk_spi_compatible {
 	bool need_pad_sel;
 	/* Must explicitly send dummy Tx bytes to do Rx only transfer */
 	bool must_tx;
+	/* some IC design adjust cfg register to enhance time accuracy */
+	bool enhance_timing;
 };
 
 struct mtk_spi {
@@ -96,6 +104,16 @@ struct mtk_spi {
 };
 
 static const struct mtk_spi_compatible mtk_common_compat;
+
+static const struct mtk_spi_compatible mt2712_compat = {
+	.must_tx = true,
+};
+
+static const struct mtk_spi_compatible mt7622_compat = {
+	.must_tx = true,
+	.enhance_timing = true,
+};
+
 static const struct mtk_spi_compatible mt8173_compat = {
 	.need_pad_sel = true,
 	.must_tx = true,
@@ -108,15 +126,23 @@ static const struct mtk_spi_compatible mt8173_compat = {
 static const struct mtk_chip_config mtk_default_chip_info = {
 	.rx_mlsb = 1,
 	.tx_mlsb = 1,
+	.cs_pol = 0,
+	.sample_sel = 0,
 };
 
 static const struct of_device_id mtk_spi_of_match[] = {
 	{ .compatible = "mediatek,mt2701-spi",
 		.data = (void *)&mtk_common_compat,
 	},
+	{ .compatible = "mediatek,mt2712-spi",
+		.data = (void *)&mt2712_compat,
+	},
 	{ .compatible = "mediatek,mt6589-spi",
 		.data = (void *)&mtk_common_compat,
 	},
+	{ .compatible = "mediatek,mt7622-spi",
+		.data = (void *)&mt7622_compat,
+	},
 	{ .compatible = "mediatek,mt8135-spi",
 		.data = (void *)&mtk_common_compat,
 	},
@@ -182,6 +208,17 @@ static int mtk_spi_prepare_message(struct spi_master *master,
 	reg_val |= SPI_CMD_RX_ENDIAN;
 #endif
 
+	if (mdata->dev_comp->enhance_timing) {
+		if (chip_config->cs_pol)
+			reg_val |= SPI_CMD_CS_POL;
+		else
+			reg_val &= ~SPI_CMD_CS_POL;
+		if (chip_config->sample_sel)
+			reg_val |= SPI_CMD_SAMPLE_SEL;
+		else
+			reg_val &= ~SPI_CMD_SAMPLE_SEL;
+	}
+
 	/* set finish and pause interrupt always enable */
 	reg_val |= SPI_CMD_FINISH_IE | SPI_CMD_PAUSE_IE;
 
@@ -233,11 +270,25 @@ static void mtk_spi_prepare_transfer(struct spi_master *master,
 	sck_time = (div + 1) / 2;
 	cs_time = sck_time * 2;
 
-	reg_val |= (((sck_time - 1) & 0xff) << SPI_CFG0_SCK_HIGH_OFFSET);
-	reg_val |= (((sck_time - 1) & 0xff) << SPI_CFG0_SCK_LOW_OFFSET);
-	reg_val |= (((cs_time - 1) & 0xff) << SPI_CFG0_CS_HOLD_OFFSET);
-	reg_val |= (((cs_time - 1) & 0xff) << SPI_CFG0_CS_SETUP_OFFSET);
-	writel(reg_val, mdata->base + SPI_CFG0_REG);
+	if (mdata->dev_comp->enhance_timing) {
+		reg_val |= (((sck_time - 1) & 0xffff)
+			   << SPI_CFG0_SCK_HIGH_OFFSET);
+		reg_val |= (((sck_time - 1) & 0xffff)
+			   << SPI_ADJUST_CFG0_SCK_LOW_OFFSET);
+		writel(reg_val, mdata->base + SPI_CFG2_REG);
+		reg_val |= (((cs_time - 1) & 0xffff)
+			   << SPI_ADJUST_CFG0_CS_HOLD_OFFSET);
+		reg_val |= (((cs_time - 1) & 0xffff)
+			   << SPI_ADJUST_CFG0_CS_SETUP_OFFSET);
+		writel(reg_val, mdata->base + SPI_CFG0_REG);
+	} else {
+		reg_val |= (((sck_time - 1) & 0xff)
+			   << SPI_CFG0_SCK_HIGH_OFFSET);
+		reg_val |= (((sck_time - 1) & 0xff) << SPI_CFG0_SCK_LOW_OFFSET);
+		reg_val |= (((cs_time - 1) & 0xff) << SPI_CFG0_CS_HOLD_OFFSET);
+		reg_val |= (((cs_time - 1) & 0xff) << SPI_CFG0_CS_SETUP_OFFSET);
+		writel(reg_val, mdata->base + SPI_CFG0_REG);
+	}
 
 	reg_val = readl(mdata->base + SPI_CFG1_REG);
 	reg_val &= ~SPI_CFG1_CS_IDLE_MASK;

drivers/spi/spi-omap2-mcspi.c

@@ -1412,9 +1412,6 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 		sprintf(mcspi->dma_channels[i].dma_tx_ch_name, "tx%d", i);
 	}
 
-	if (status < 0)
-		goto free_master;
-
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
 	pm_runtime_enable(&pdev->dev);

include/linux/platform_data/spi-mt65xx.h

@@ -16,5 +16,7 @@
 struct mtk_chip_config {
 	u32 tx_mlsb;
 	u32 rx_mlsb;
+	u32 cs_pol;
+	u32 sample_sel;
 };
 #endif