ARM: dts: sunxi: Remove useless pinctrl nodes

We have for the H3 boards some kind of cargo cult apparently, where we
would have a pinctrl node even for GPIOs without any particular settings.

This is pretty much useless, so let's remove them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arch/arm/boot/dts/sun8i-h3-nanopi.dtsi

@@ -59,8 +59,6 @@ chosen {
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_npi>, <&leds_r_npi>;
 
 		status {
 			label = "nanopi:blue:status";
@@ -78,8 +76,6 @@ pwr {
 	r_gpio_keys {
 		compatible = "gpio-keys";
 		input-name = "k1";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_npi>;
 
 		k1 {
 			label = "k1";
@@ -104,25 +100,6 @@ &ohci3 {
 	status = "okay";
 };
 
-&pio {
-	leds_npi: led_pins {
-		pins = "PA10";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_npi: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_npi: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;

arch/arm/boot/dts/sun8i-h3-orangepi-2.dts

@@ -75,8 +75,6 @@ hdmi_con_in: endpoint {
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		status_led {
 			label = "orangepi:red:status";
@@ -92,8 +90,6 @@ pwr_led {
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw2 {
 			label = "sw2";
@@ -110,8 +106,6 @@ sw4 {
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
 	};
 };
@@ -179,30 +173,6 @@ rtl8189: sdio_wifi@1 {
 	};
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3", "PL4";
-		function = "gpio_in";
-	};
-
-	wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
-		pins = "PL7";
-		function = "gpio_out";
-	};
-};
-
 &reg_usb1_vbus {
 	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
 	status = "okay";

arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts

@@ -74,8 +74,6 @@ hdmi_con_in: endpoint {
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		pwr_led {
 			label = "orangepi:green:pwr";
@@ -91,8 +89,6 @@ status_led {
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw4 {
 			label = "sw4";
@@ -160,25 +156,6 @@ &ohci2 {
 	status = "okay";
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;

arch/arm/boot/dts/sun8i-h3-orangepi-one.dts

@@ -73,8 +73,6 @@ hdmi_con_in: endpoint {
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		pwr_led {
 			label = "orangepi:green:pwr";
@@ -90,8 +88,6 @@ status_led {
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw4 {
 			label = "sw4";
@@ -166,25 +162,6 @@ &ohci1 {
 	status = "okay";
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &reg_usb0_vbus {
 	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
 	status = "okay";

arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts

@@ -73,8 +73,6 @@ hdmi_con_in: endpoint {
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		pwr_led {
 			label = "orangepi:green:pwr";
@@ -90,8 +88,6 @@ status_led {
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw4 {
 			label = "sw4";
@@ -179,13 +175,6 @@ &ohci3 {
 	status = "okay";
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
 &r_i2c {
 	status = "okay";
 
@@ -210,18 +199,6 @@ reg_vdd_cpux: regulator@65 {
 	};
 };
 
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &reg_usb0_vbus {
 	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
 	status = "okay";

arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

@@ -63,8 +63,6 @@ reg_gmac_3v3: gmac-3v3 {
 
 	reg_usb3_vbus: usb3-vbus {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb3_vbus_pin_a>;
 		regulator-name = "usb3-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -116,13 +114,6 @@ &mmc2_8bit_pins {
 	bias-pull-up;
 };
 
-&pio {
-	usb3_vbus_pin_a: usb3_vbus_pin {
-		pins = "PG11";
-		function = "gpio_out";
-	};
-};
-
 &r_i2c {
 	status = "okay";