Merge tag 'sti-reset-for-v3.19-1' of...

Merge tag 'sti-reset-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti into reset/for_v3.19

STi reset controller updates for v3.19.

This tag adds support to STiH407 reset controllers:
  1. st,stih407-powerdown
  2. st,stih407-softreset
  3. st,stih407-picophyreset

Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt

+STMicroelectronics STi family Sysconfig Picophy SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip PicoPHY USB2 phy(s) using "softreset" control bits found in
+the STi family SoC system configuration registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to Documentation/devicetree/bindings/reset/reset.txt
+for common reset controller binding usage.
+
+Required properties:
+- compatible: Should be "st,stih407-picophyreset"
+- #reset-cells: 1, see below
+
+Example:
+
+	picophyreset: picophyreset-controller {
+		compatible = "st,stih407-picophyreset";
+		#reset-cells = <1>;
+	};
+
+Specifying picophyreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the picophyreset device node and an
+index specifying which channel to use, as described in
+Documentation/devicetree/bindings/reset/reset.txt.
+
+Example:
+
+	usb2_picophy0: usbpicophy@0 {
+		resets = <&picophyreset STIH407_PICOPHY0_RESET>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+include/dt-bindings/reset-controller/stih407-resets.h

drivers/reset/sti/Kconfig

@@ -12,4 +12,8 @@ config STIH416_RESET
 	bool
 	select STI_RESET_SYSCFG
 
+config STIH407_RESET
+	bool
+	select STI_RESET_SYSCFG
+
 endif

drivers/reset/sti/Makefile

@@ -2,3 +2,4 @@ obj-$(CONFIG_STI_RESET_SYSCFG) += reset-syscfg.o
 
 obj-$(CONFIG_STIH415_RESET) += reset-stih415.o
 obj-$(CONFIG_STIH416_RESET) += reset-stih416.o
+obj-$(CONFIG_STIH407_RESET) += reset-stih407.o

drivers/reset/sti/reset-stih407.c

+/*
+ * Copyright (C) 2014 STMicroelectronics (R&D) Limited
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/reset-controller/stih407-resets.h>
+#include "reset-syscfg.h"
+
+/* STiH407 Peripheral powerdown definitions. */
+static const char stih407_core[] = "st,stih407-core-syscfg";
+static const char stih407_sbc_reg[] = "st,stih407-sbc-reg-syscfg";
+static const char stih407_lpm[] = "st,stih407-lpm-syscfg";
+
+#define STIH407_PDN_0(_bit) \
+	_SYSCFG_RST_CH(stih407_core, SYSCFG_5000, _bit, SYSSTAT_5500, _bit)
+#define STIH407_PDN_1(_bit) \
+	_SYSCFG_RST_CH(stih407_core, SYSCFG_5001, _bit, SYSSTAT_5501, _bit)
+#define STIH407_PDN_ETH(_bit, _stat) \
+	_SYSCFG_RST_CH(stih407_sbc_reg, SYSCFG_4032, _bit, SYSSTAT_4520, _stat)
+
+/* Powerdown requests control 0 */
+#define SYSCFG_5000	0x0
+#define SYSSTAT_5500	0x7d0
+/* Powerdown requests control 1 (High Speed Links) */
+#define SYSCFG_5001	0x4
+#define SYSSTAT_5501	0x7d4
+
+/* Ethernet powerdown/status/reset */
+#define SYSCFG_4032	0x80
+#define SYSSTAT_4520	0x820
+#define SYSCFG_4002	0x8
+
+static const struct syscfg_reset_channel_data stih407_powerdowns[] = {
+	[STIH407_EMISS_POWERDOWN] = STIH407_PDN_0(1),
+	[STIH407_NAND_POWERDOWN] = STIH407_PDN_0(0),
+	[STIH407_USB3_POWERDOWN] = STIH407_PDN_1(6),
+	[STIH407_USB2_PORT1_POWERDOWN] = STIH407_PDN_1(5),
+	[STIH407_USB2_PORT0_POWERDOWN] = STIH407_PDN_1(4),
+	[STIH407_PCIE1_POWERDOWN] = STIH407_PDN_1(3),
+	[STIH407_PCIE0_POWERDOWN] = STIH407_PDN_1(2),
+	[STIH407_SATA1_POWERDOWN] = STIH407_PDN_1(1),
+	[STIH407_SATA0_POWERDOWN] = STIH407_PDN_1(0),
+	[STIH407_ETH1_POWERDOWN] = STIH407_PDN_ETH(0, 2),
+};
+
+/* Reset Generator control 0/1 */
+#define SYSCFG_5131	0x20c
+#define SYSCFG_5132	0x210
+
+#define LPM_SYSCFG_1	0x4	/* Softreset IRB & SBC UART */
+
+#define STIH407_SRST_CORE(_reg, _bit) \
+	_SYSCFG_RST_CH_NO_ACK(stih407_core, _reg, _bit)
+
+#define STIH407_SRST_SBC(_reg, _bit) \
+	_SYSCFG_RST_CH_NO_ACK(stih407_sbc_reg, _reg, _bit)
+
+#define STIH407_SRST_LPM(_reg, _bit) \
+	_SYSCFG_RST_CH_NO_ACK(stih407_lpm, _reg, _bit)
+
+static const struct syscfg_reset_channel_data stih407_softresets[] = {
+	[STIH407_ETH1_SOFTRESET] = STIH407_SRST_SBC(SYSCFG_4002, 4),
+	[STIH407_MMC1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 3),
+	[STIH407_USB2_PORT0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 28),
+	[STIH407_USB2_PORT1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 29),
+	[STIH407_PICOPHY_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 30),
+	[STIH407_IRB_SOFTRESET] = STIH407_SRST_LPM(LPM_SYSCFG_1, 6),
+	[STIH407_PCIE0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 6),
+	[STIH407_PCIE1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 15),
+	[STIH407_SATA0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 7),
+	[STIH407_SATA1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 16),
+	[STIH407_MIPHY0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 4),
+	[STIH407_MIPHY1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 13),
+	[STIH407_MIPHY2_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 22),
+	[STIH407_SATA0_PWR_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 5),
+	[STIH407_SATA1_PWR_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 14),
+	[STIH407_DELTA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 3),
+	[STIH407_BLITTER_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 10),
+	[STIH407_HDTVOUT_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 11),
+	[STIH407_HDQVDP_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 12),
+	[STIH407_VDP_AUX_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 14),
+	[STIH407_COMPO_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 15),
+	[STIH407_HDMI_TX_PHY_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 21),
+	[STIH407_JPEG_DEC_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 23),
+	[STIH407_VP8_DEC_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 24),
+	[STIH407_GPU_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 30),
+	[STIH407_HVA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 0),
+	[STIH407_ERAM_HVA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 1),
+	[STIH407_LPM_SOFTRESET] = STIH407_SRST_SBC(SYSCFG_4002, 2),
+	[STIH407_KEYSCAN_SOFTRESET] = STIH407_SRST_LPM(LPM_SYSCFG_1, 8),
+};
+
+/* PicoPHY reset/control */
+#define SYSCFG_5061	0x0f4
+
+static const struct syscfg_reset_channel_data stih407_picophyresets[] = {
+	[STIH407_PICOPHY0_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 5),
+	[STIH407_PICOPHY1_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 6),
+	[STIH407_PICOPHY2_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 7),
+};
+
+static const struct syscfg_reset_controller_data stih407_powerdown_controller = {
+	.wait_for_ack = true,
+	.nr_channels = ARRAY_SIZE(stih407_powerdowns),
+	.channels = stih407_powerdowns,
+};
+
+static const struct syscfg_reset_controller_data stih407_softreset_controller = {
+	.wait_for_ack = false,
+	.active_low = true,
+	.nr_channels = ARRAY_SIZE(stih407_softresets),
+	.channels = stih407_softresets,
+};
+
+static const struct syscfg_reset_controller_data stih407_picophyreset_controller = {
+	.wait_for_ack = false,
+	.nr_channels = ARRAY_SIZE(stih407_picophyresets),
+	.channels = stih407_picophyresets,
+};
+
+static struct of_device_id stih407_reset_match[] = {
+	{
+		.compatible = "st,stih407-powerdown",
+		.data = &stih407_powerdown_controller,
+	},
+	{
+		.compatible = "st,stih407-softreset",
+		.data = &stih407_softreset_controller,
+	},
+	{
+		.compatible = "st,stih407-picophyreset",
+		.data = &stih407_picophyreset_controller,
+	},
+	{ /* sentinel */ },
+};
+
+static struct platform_driver stih407_reset_driver = {
+	.probe = syscfg_reset_probe,
+	.driver = {
+		.name = "reset-stih407",
+		.of_match_table = stih407_reset_match,
+	},
+};
+
+static int __init stih407_reset_init(void)
+{
+	return platform_driver_register(&stih407_reset_driver);
+}
+
+arch_initcall(stih407_reset_init);

include/dt-bindings/reset-controller/stih407-resets.h

+/*
+ * This header provides constants for the reset controller
+ * based peripheral powerdown requests on the STMicroelectronics
+ * STiH407 SoC.
+ */
+#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH407
+#define _DT_BINDINGS_RESET_CONTROLLER_STIH407
+
+/* Powerdown requests control 0 */
+#define STIH407_EMISS_POWERDOWN		0
+#define STIH407_NAND_POWERDOWN		1
+
+/* Synp GMAC PowerDown */
+#define STIH407_ETH1_POWERDOWN		2
+
+/* Powerdown requests control 1 */
+#define STIH407_USB3_POWERDOWN		3
+#define STIH407_USB2_PORT1_POWERDOWN	4
+#define STIH407_USB2_PORT0_POWERDOWN	5
+#define STIH407_PCIE1_POWERDOWN		6
+#define STIH407_PCIE0_POWERDOWN		7
+#define STIH407_SATA1_POWERDOWN		8
+#define STIH407_SATA0_POWERDOWN		9
+
+/* Reset defines */
+#define STIH407_ETH1_SOFTRESET		0
+#define STIH407_MMC1_SOFTRESET		1
+#define STIH407_PICOPHY_SOFTRESET	2
+#define STIH407_IRB_SOFTRESET		3
+#define STIH407_PCIE0_SOFTRESET		4
+#define STIH407_PCIE1_SOFTRESET		5
+#define STIH407_SATA0_SOFTRESET		6
+#define STIH407_SATA1_SOFTRESET		7
+#define STIH407_MIPHY0_SOFTRESET	8
+#define STIH407_MIPHY1_SOFTRESET	9
+#define STIH407_MIPHY2_SOFTRESET	10
+#define STIH407_SATA0_PWR_SOFTRESET	11
+#define STIH407_SATA1_PWR_SOFTRESET	12
+#define STIH407_DELTA_SOFTRESET		13
+#define STIH407_BLITTER_SOFTRESET	14
+#define STIH407_HDTVOUT_SOFTRESET	15
+#define STIH407_HDQVDP_SOFTRESET	16
+#define STIH407_VDP_AUX_SOFTRESET	17
+#define STIH407_COMPO_SOFTRESET		18
+#define STIH407_HDMI_TX_PHY_SOFTRESET	19
+#define STIH407_JPEG_DEC_SOFTRESET	20
+#define STIH407_VP8_DEC_SOFTRESET	21
+#define STIH407_GPU_SOFTRESET		22
+#define STIH407_HVA_SOFTRESET		23
+#define STIH407_ERAM_HVA_SOFTRESET	24
+#define STIH407_LPM_SOFTRESET		25
+#define STIH407_KEYSCAN_SOFTRESET	26
+#define STIH407_USB2_PORT0_SOFTRESET	27
+#define STIH407_USB2_PORT1_SOFTRESET	28
+
+/* Picophy reset defines */
+#define STIH407_PICOPHY0_RESET		0
+#define STIH407_PICOPHY1_RESET		1
+#define STIH407_PICOPHY2_RESET		2
+
+#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH407 */