Merge tag 'mvebu-dt64-5.1-1' of git://git.infradead.org/linux-mvebu into arm/dt

mvebu dt64 for 5.1 (part 1)

 - Interrupt support to Armada 7K/8K thermal nodes
 - Armada 37xx related patches allowing to enable suspend to RAM
   (USB2, USB3, PCIe, SATA, DSA)
 - uDPU board support (Armada-3720 based):single-port FTTdp
    distribution point unit
 - Fixes for EspressoBin Ethernet support when using U-Boot mainline
 - cleanup for partitions under flashes nodes

* tag 'mvebu-dt64-5.1-1' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs
  arm64: dts: marvell: armada-3720-espressobin: declare SATA PHY property
  arm64: dts: marvell: armada-3720-espressobin: declare PCIe PHY
  arm64: dts: marvell: armada-37xx: declare the COMPHY node
  arm64: dts: marvell: Remove unnecessary #address-cells/#size-cells under flashes
  arm64: dts: armada-3720-espressobin: Set mv88e6341 cpu port as RGMII-ID
  arm64: dts: armada-3720-espressobin: Configure RGMII and SMI pins
  arm64: dts: marvell: Add device tree for uDPU board
  arm64: dts: marvell: armada-3720-espressobin: declare PCIe warm reset pin
  arm64: dts: marvell: armada-37xx: declare PCIe reset pin
  arm64: dts: marvell: armada-37xx: declare USB2 UTMI PHYs
  arm64: dts: marvell: armada-37xx: fix USB2 memory region
  arm64: dts: marvell: armada-37xx: declare SATA clock
  arm64: dts: marvell: armada-37xx: fix SATA node scope
  arm64: dts: marvell: add interrupt support to cp110 thermal node
  arm64: dts: marvell: add interrupt support to ap806 thermal node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm64/boot/dts/marvell/Makefile

@@ -2,6 +2,7 @@
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb

arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts

@@ -46,11 +46,16 @@ vcc_sd_reg1: regulator {
 /* J9 */
 &pcie0 {
 	status = "okay";
+	phys = <&comphy1 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
 };
 
 /* J6 */
 &sata {
 	status = "okay";
+	phys = <&comphy2 0>;
+	phy-names = "sata-phy";
 };
 
 /* J1 */
@@ -156,6 +161,11 @@ port@0 {
 				reg = <0>;
 				label = "cpu";
 				ethernet = <&eth0>;
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
 			};
 
 			port@1 {
@@ -196,6 +206,8 @@ switch0phy2: switch0phy2@13 {
 };
 
 &eth0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
 	phy-mode = "rgmii-id";
 	status = "okay";
 

arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2019 Methode Electronics
+ * Copyright (C) 2019 Telus
+ *
+ * Vladimir Vid <vladimir.vid@sartura.hr>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+	model = "Methode uDPU Board";
+	compatible = "methode,udpu", "marvell,armada3720";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	leds {
+		pinctrl-names = "default";
+		compatible = "gpio-leds";
+
+		power1 {
+			label = "udpu:green:power";
+			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+		};
+
+		power2 {
+			label = "udpu:red:power";
+			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+		};
+
+		network1 {
+			label = "udpu:green:network";
+			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+		};
+
+		network2 {
+			label = "udpu:red:network";
+			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+		};
+
+		alarm1 {
+			label = "udpu:green:alarm";
+			gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
+		};
+
+		alarm2 {
+			label = "udpu:red:alarm";
+			gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sfp_eth0: sfp-eth0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c0>;
+		los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp_eth1: sfp-eth1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&sdhci0 {
+	status = "okay";
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	marvell,pad-type = "fixed-1-8v";
+	non-removable;
+	no-sd;
+	no-sdio;
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_quad_pins>;
+
+	m25p80@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <54000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* only bootloader is located on the SPI */
+			partition@0 {
+				label = "uboot";
+				reg = <0 0x400000>;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	lm75@48 {
+		status = "okay";
+		compatible = "lm75";
+		reg = <0x48>;
+	};
+
+	lm75@49 {
+		status = "okay";
+		compatible = "lm75";
+		reg = <0x49>;
+	};
+};
+
+&eth0 {
+	phy-mode = "sgmii";
+	status = "okay";
+	managed = "in-band-status";
+	sfp = <&sfp_eth0>;
+};
+
+&eth1 {
+	phy-mode = "sgmii";
+	status = "okay";
+	managed = "in-band-status";
+	sfp = <&sfp_eth1>;
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};

arch/arm64/boot/dts/marvell/armada-37xx.dtsi

@@ -247,6 +247,35 @@ nb_pm: syscon@14000 {
 				reg = <0x14000 0x60>;
 			};
 
+			comphy: phy@18300 {
+				compatible = "marvell,comphy-a3700";
+				reg = <0x18300 0x300>,
+				      <0x1F000 0x400>,
+				      <0x5C000 0x400>,
+				      <0xe0178 0x8>;
+				reg-names = "comphy",
+					    "lane1_pcie_gbe",
+					    "lane0_usb3_gbe",
+					    "lane2_sata_usb3";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				comphy0: phy@0 {
+					reg = <0>;
+					#phy-cells = <1>;
+				};
+
+				comphy1: phy@1 {
+					reg = <1>;
+					#phy-cells = <1>;
+				};
+
+				comphy2: phy@2 {
+					reg = <2>;
+					#phy-cells = <1>;
+				};
+			};
+
 			pinctrl_sb: pinctrl@18800 {
 				compatible = "marvell,armada3710-sb-pinctrl",
 					     "syscon", "simple-mfd";
@@ -271,11 +300,25 @@ rgmii_pins: mii-pins {
 					function = "mii";
 				};
 
+				smi_pins: smi-pins {
+					groups = "smi";
+					function = "smi";
+				};
+
 				sdio_pins: sdio-pins {
 					groups = "sdio_sb";
 					function = "sdio";
 				};
 
+				pcie_reset_pins: pcie-reset-pins {
+					groups = "pcie1";
+					function = "pcie";
+				};
+
+				pcie_clkreq_pins: pcie-clkreq-pins {
+					groups = "pcie1_clkreq";
+					function = "pcie";
+				};
 			};
 
 			eth0: ethernet@30000 {
@@ -305,18 +348,50 @@ usb3: usb@58000 {
 				compatible = "marvell,armada3700-xhci",
 				"generic-xhci";
 				reg = <0x58000 0x4000>;
+				marvell,usb-misc-reg = <&usb32_syscon>;
 				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&sb_periph_clk 12>;
+				phys = <&comphy0 0>, <&usb2_utmi_otg_phy>;
+				phy-names = "usb3-phy", "usb2-utmi-otg-phy";
 				status = "disabled";
 			};
 
+			usb2_utmi_otg_phy: phy@5d000 {
+				compatible = "marvell,a3700-utmi-otg-phy";
+				reg = <0x5d000 0x800>;
+				marvell,usb-misc-reg = <&usb32_syscon>;
+				#phy-cells = <0>;
+			};
+
+			usb32_syscon: system-controller@5d800 {
+				compatible = "marvell,armada-3700-usb2-host-device-misc",
+				"syscon";
+				reg = <0x5d800 0x800>;
+			};
+
 			usb2: usb@5e000 {
 				compatible = "marvell,armada-3700-ehci";
-				reg = <0x5e000 0x2000>;
+				reg = <0x5e000 0x1000>;
+				marvell,usb-misc-reg = <&usb2_syscon>;
 				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_utmi_host_phy>;
+				phy-names = "usb2-utmi-host-phy";
 				status = "disabled";
 			};
 
+			usb2_utmi_host_phy: phy@5f000 {
+				compatible = "marvell,a3700-utmi-host-phy";
+				reg = <0x5f000 0x800>;
+				marvell,usb-misc-reg = <&usb2_syscon>;
+				#phy-cells = <0>;
+			};
+
+			usb2_syscon: system-controller@5f800 {
+				compatible = "marvell,armada-3700-usb2-host-misc",
+				"syscon";
+				reg = <0x5f800 0x800>;
+			};
+
 			xor@60900 {
 				compatible = "marvell,armada-3700-xor";
 				reg = <0x60900 0x100>,
@@ -368,8 +443,9 @@ sdhci0: sdhci@d8000 {
 
 			sata: sata@e0000 {
 				compatible = "marvell,armada-3700-ahci";
-				reg = <0xe0000 0x2000>;
+				reg = <0xe0000 0x178>;
 				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&nb_periph_clk 1>;
 				status = "disabled";
 			};
 

arch/arm64/boot/dts/marvell/armada-7040-db.dts

@@ -66,8 +66,6 @@ &spi0 {
 	status = "okay";
 
 	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <10000000>;
@@ -169,8 +167,6 @@ &cp0_spi1 {
 	status = "okay";
 
 	spi-flash@0 {
-		#address-cells = <0x1>;
-		#size-cells = <0x1>;
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-max-frequency = <20000000>;

arch/arm64/boot/dts/marvell/armada-8040-db.dts

@@ -81,8 +81,6 @@ &spi0 {
 	status = "okay";
 
 	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <10000000>;
@@ -214,8 +212,6 @@ &cp1_spi1 {
 	status = "okay";
 
 	spi-flash@0 {
-		#address-cells = <0x1>;
-		#size-cells = <0x1>;
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-max-frequency = <20000000>;

arch/arm64/boot/dts/marvell/armada-ap806.dtsi

@@ -283,6 +283,8 @@ ap_syscon1: system-controller@6f8000 {
 				ap_thermal: thermal-sensor@80 {
 					compatible = "marvell,armada-ap806-thermal";
 					reg = <0x80 0x10>;
+					interrupt-parent = <&sei>;
+					interrupts = <18>;
 					#thermal-sensor-cells = <1>;
 				};
 			};
@@ -293,16 +295,26 @@ ap_thermal: thermal-sensor@80 {
 	 * The thermal IP features one internal sensor plus, if applicable, one
 	 * remote channel wired to one sensor per CPU.
 	 *
+	 * Only one thermal zone per AP/CP may trigger interrupts at a time, the
+	 * first one that will have a critical trip point will be chosen.
+	 *
 	 * The cooling maps are always empty as there are no cooling devices.
 	 */
 	thermal-zones {
 		ap_thermal_ic: ap-thermal-ic {
-			polling-delay-passive = <1000>;
-			polling-delay = <1000>;
+			polling-delay-passive = <0>; /* Interrupt driven */
+			polling-delay = <0>; /* Interrupt driven */
 
 			thermal-sensors = <&ap_thermal 0>;
 
-			trips {	};
+			trips {
+				ap_crit: ap-crit {
+					temperature = <100000>; /* mC degrees */
+					hysteresis = <2000>; /* mC degrees */
+					type = "critical";
+				};
+			};
+
 			cooling-maps { };
 		};
 

arch/arm64/boot/dts/marvell/armada-cp110.dtsi

@@ -28,12 +28,19 @@ / {
 	 */
 	thermal-zones {
 		CP110_LABEL(thermal_ic): CP110_NODE_NAME(thermal-ic) {
-			polling-delay-passive = <1000>;
-			polling-delay = <1000>;
+			polling-delay-passive = <0>; /* Interrupt driven */
+			polling-delay = <0>; /* Interrupt driven */
 
 			thermal-sensors = <&CP110_LABEL(thermal) 0>;
 
-			trips {	};
+			trips {
+				CP110_LABEL(crit): crit {
+					temperature = <100000>; /* mC degrees */
+					hysteresis = <2000>; /* mC degrees */
+					type = "critical";
+				};
+			};
+
 			cooling-maps { };
 		};
 	};
@@ -259,6 +266,8 @@ CP110_LABEL(syscon1): system-controller@400000 {
 			CP110_LABEL(thermal): thermal-sensor@70 {
 				compatible = "marvell,armada-cp110-thermal";
 				reg = <0x70 0x10>;
+				interrupts-extended =
+					<&CP110_LABEL(icu_sei) 116 IRQ_TYPE_LEVEL_HIGH>;
 				#thermal-sensor-cells = <1>;
 			};
 		};