Merge tag 'nand/for-4.8' of github.com:linux-nand/linux into mtd

Pull NAND changes from Boris Brezillon:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver

And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""

Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt

@@ -46,6 +46,10 @@ Required properties:
 			0 maps to GPMC_WAIT0 pin.
  - gpio-cells:		Must be set to 2
 
+Required properties when using NAND prefetch dma:
+ - dmas			GPMC NAND prefetch dma channel
+ - dma-names		Must be set to "rxtx"
+
 Timing properties for child nodes. All are optional and default to 0.
 
  - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
@@ -137,7 +141,8 @@ Example for an AM33xx board:
 		ti,hwmods = "gpmc";
 		reg = <0x50000000 0x2000>;
 		interrupts = <100>;
-
+		dmas = <&edma 52 0>;
+		dma-names = "rxtx";
 		gpmc,num-cs = <8>;
 		gpmc,num-waitpins = <2>;
 		#address-cells = <2>;

Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt

@@ -27,6 +27,7 @@ Required properties:
                          brcm,brcmnand-v6.2
                          brcm,brcmnand-v7.0
                          brcm,brcmnand-v7.1
+                         brcm,brcmnand-v7.2
                          brcm,brcmnand
 - reg              : the register start and length for NAND register region.
                      (optional) Flash DMA register range (if present)

Documentation/devicetree/bindings/mtd/gpmc-nand.txt

@@ -39,7 +39,7 @@ Optional properties:
 
 		"prefetch-polled"	Prefetch polled mode (default)
 		"polled"		Polled mode, without prefetch
-		"prefetch-dma"		Prefetch enabled sDMA mode
+		"prefetch-dma"		Prefetch enabled DMA mode
 		"prefetch-irq"		Prefetch enabled irq mode
 
  - elm_id:	<deprecated> use "ti,elm-id" instead

Documentation/devicetree/bindings/mtd/mtk-nand.txt

+MTK SoCs NAND FLASH controller (NFC) DT binding
+
+This file documents the device tree bindings for MTK SoCs NAND controllers.
+The functional split of the controller requires two drivers to operate:
+the nand controller interface driver and the ECC engine driver.
+
+The hardware description for both devices must be captured as device
+tree nodes.
+
+1) NFC NAND Controller Interface (NFI):
+=======================================
+
+The first part of NFC is NAND Controller Interface (NFI) HW.
+Required NFI properties:
+- compatible:			Should be "mediatek,mtxxxx-nfc".
+- reg:				Base physical address and size of NFI.
+- interrupts:			Interrupts of NFI.
+- clocks:			NFI required clocks.
+- clock-names:			NFI clocks internal name.
+- status:			Disabled default. Then set "okay" by platform.
+- ecc-engine:			Required ECC Engine node.
+- #address-cells:		NAND chip index, should be 1.
+- #size-cells:			Should be 0.
+
+Example:
+
+	nandc: nfi@1100d000 {
+		compatible = "mediatek,mt2701-nfc";
+		reg = <0 0x1100d000 0 0x1000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_NFI>,
+			 <&pericfg CLK_PERI_NFI_PAD>;
+		clock-names = "nfi_clk", "pad_clk";
+		status = "disabled";
+		ecc-engine = <&bch>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+        };
+
+Platform related properties, should be set in {platform_name}.dts:
+- children nodes:	NAND chips.
+
+Children nodes properties:
+- reg:			Chip Select Signal, default 0.
+			Set as reg = <0>, <1> when need 2 CS.
+Optional:
+- nand-on-flash-bbt:	Store BBT on NAND Flash.
+- nand-ecc-mode:	the NAND ecc mode (check driver for supported modes)
+- nand-ecc-step-size:	Number of data bytes covered by a single ECC step.
+			valid values: 512 and 1024.
+			1024 is recommended for large page NANDs.
+- nand-ecc-strength:	Number of bits to correct per ECC step.
+			The valid values that the controller supports are: 4, 6,
+			8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44,
+			48, 52, 56, 60.
+			The strength should be calculated as follows:
+			E = (S - F) * 8 / 14
+			S = O / (P / Q)
+				E :	nand-ecc-strength.
+				S :	spare size per sector.
+				F :	FDM size, should be in the range [1,8].
+					It is used to store free oob data.
+				O :	oob size.
+				P :	page size.
+				Q :	nand-ecc-step-size.
+			If the result does not match any one of the listed
+			choices above, please select the smaller valid value from
+			the list.
+			(otherwise the driver will do the adjustment at runtime)
+- pinctrl-names:	Default NAND pin GPIO setting name.
+- pinctrl-0:		GPIO setting node.
+
+Example:
+	&pio {
+		nand_pins_default: nanddefault {
+			pins_dat {
+				pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
+					 <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
+					 <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
+					 <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
+					 <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
+					 <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
+					 <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
+					 <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
+					 <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
+				input-enable;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-up;
+			};
+
+			pins_we {
+				pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+			};
+
+			pins_ale {
+				pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
+				drive-strength = <MTK_DRIVE_8mA>;
+				bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+			};
+		};
+	};
+
+	&nandc {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&nand_pins_default>;
+		nand@0 {
+			reg = <0>;
+			nand-on-flash-bbt;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <24>;
+			nand-ecc-step-size = <1024>;
+		};
+	};
+
+NAND chip optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			preloader@0 {
+				label = "pl";
+				read-only;
+				reg = <0x00000000 0x00400000>;
+			};
+			android@0x00400000 {
+				label = "android";
+				reg = <0x00400000 0x12c00000>;
+			};
+		};
+	};
+
+2) ECC Engine:
+==============
+
+Required BCH properties:
+- compatible:	Should be "mediatek,mtxxxx-ecc".
+- reg:		Base physical address and size of ECC.
+- interrupts:	Interrupts of ECC.
+- clocks:	ECC required clocks.
+- clock-names:	ECC clocks internal name.
+- status:	Disabled default. Then set "okay" by platform.
+
+Example:
+
+	bch: ecc@1100e000 {
+		compatible = "mediatek,mt2701-ecc";
+		reg = <0 0x1100e000 0 0x1000>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_NFI_ECC>;
+		clock-names = "nfiecc_clk";
+		status = "disabled";
+	};

Documentation/devicetree/bindings/mtd/sunxi-nand.txt

@@ -11,10 +11,16 @@ Required properties:
     * "ahb" : AHB gating clock
     * "mod" : nand controller clock
 
+Optional properties:
+- dmas : shall reference DMA channel associated to the NAND controller.
+- dma-names : shall be "rxtx".
+
 Optional children nodes:
 Children nodes represent the available nand chips.
 
 Optional properties:
+- reset : phandle + reset specifier pair
+- reset-names : must contain "ahb"
 - allwinner,rb : shall contain the native Ready/Busy ids.
  or
 - rb-gpios : shall contain the gpios used as R/B pins.

drivers/mtd/nand/Kconfig

@@ -539,7 +539,6 @@ config MTD_NAND_FSMC
 config MTD_NAND_XWAY
 	tristate "Support for NAND on Lantiq XWAY SoC"
 	depends on LANTIQ && SOC_TYPE_XWAY
-	select MTD_NAND_PLATFORM
 	help
 	  Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
 	  to the External Bus Unit (EBU).
@@ -563,4 +562,11 @@ config MTD_NAND_QCOM
 	  Enables support for NAND flash chips on SoCs containing the EBI2 NAND
 	  controller. This controller is found on IPQ806x SoC.
 
+config MTD_NAND_MTK
+	tristate "Support for NAND controller on MTK SoCs"
+	depends on HAS_DMA
+	help
+	  Enables support for NAND controller on MTK SoCs.
+	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
+
 endif # MTD_NAND

drivers/mtd/nand/Makefile

@@ -57,5 +57,6 @@ obj-$(CONFIG_MTD_NAND_SUNXI)		+= sunxi_nand.o
 obj-$(CONFIG_MTD_NAND_HISI504)	        += hisi504_nand.o
 obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
 obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
+obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_nand.o mtk_ecc.o
 
 nand-objs := nand_base.o nand_bbt.o nand_timings.o

drivers/mtd/nand/brcmnand/brcmnand.c

@@ -340,6 +340,36 @@ static const u16 brcmnand_regs_v71[] = {
 	[BRCMNAND_FC_BASE]		= 0x400,
 };
 
+/* BRCMNAND v7.2 */
+static const u16 brcmnand_regs_v72[] = {
+	[BRCMNAND_CMD_START]		=  0x04,
+	[BRCMNAND_CMD_EXT_ADDRESS]	=  0x08,
+	[BRCMNAND_CMD_ADDRESS]		=  0x0c,
+	[BRCMNAND_INTFC_STATUS]		=  0x14,
+	[BRCMNAND_CS_SELECT]		=  0x18,
+	[BRCMNAND_CS_XOR]		=  0x1c,
+	[BRCMNAND_LL_OP]		=  0x20,
+	[BRCMNAND_CS0_BASE]		=  0x50,
+	[BRCMNAND_CS1_BASE]		=     0,
+	[BRCMNAND_CORR_THRESHOLD]	=  0xdc,
+	[BRCMNAND_CORR_THRESHOLD_EXT]	=  0xe0,
+	[BRCMNAND_UNCORR_COUNT]		=  0xfc,
+	[BRCMNAND_CORR_COUNT]		= 0x100,
+	[BRCMNAND_CORR_EXT_ADDR]	= 0x10c,
+	[BRCMNAND_CORR_ADDR]		= 0x110,
+	[BRCMNAND_UNCORR_EXT_ADDR]	= 0x114,
+	[BRCMNAND_UNCORR_ADDR]		= 0x118,
+	[BRCMNAND_SEMAPHORE]		= 0x150,
+	[BRCMNAND_ID]			= 0x194,
+	[BRCMNAND_ID_EXT]		= 0x198,
+	[BRCMNAND_LL_RDATA]		= 0x19c,
+	[BRCMNAND_OOB_READ_BASE]	= 0x200,
+	[BRCMNAND_OOB_READ_10_BASE]	=     0,
+	[BRCMNAND_OOB_WRITE_BASE]	= 0x400,
+	[BRCMNAND_OOB_WRITE_10_BASE]	=     0,
+	[BRCMNAND_FC_BASE]		= 0x600,
+};
+
 enum brcmnand_cs_reg {
 	BRCMNAND_CS_CFG_EXT = 0,
 	BRCMNAND_CS_CFG,
@@ -435,7 +465,9 @@ static int brcmnand_revision_init(struct brcmnand_controller *ctrl)
 	}
 
 	/* Register offsets */
-	if (ctrl->nand_version >= 0x0701)
+	if (ctrl->nand_version >= 0x0702)
+		ctrl->reg_offsets = brcmnand_regs_v72;
+	else if (ctrl->nand_version >= 0x0701)
 		ctrl->reg_offsets = brcmnand_regs_v71;
 	else if (ctrl->nand_version >= 0x0600)
 		ctrl->reg_offsets = brcmnand_regs_v60;
@@ -480,7 +512,9 @@ static int brcmnand_revision_init(struct brcmnand_controller *ctrl)
 	}
 
 	/* Maximum spare area sector size (per 512B) */
-	if (ctrl->nand_version >= 0x0600)
+	if (ctrl->nand_version >= 0x0702)
+		ctrl->max_oob = 128;
+	else if (ctrl->nand_version >= 0x0600)
 		ctrl->max_oob = 64;
 	else if (ctrl->nand_version >= 0x0500)
 		ctrl->max_oob = 32;
@@ -583,14 +617,20 @@ static void brcmnand_wr_corr_thresh(struct brcmnand_host *host, u8 val)
 	enum brcmnand_reg reg = BRCMNAND_CORR_THRESHOLD;
 	int cs = host->cs;
 
-	if (ctrl->nand_version >= 0x0600)
+	if (ctrl->nand_version >= 0x0702)
+		bits = 7;
+	else if (ctrl->nand_version >= 0x0600)
 		bits = 6;
 	else if (ctrl->nand_version >= 0x0500)
 		bits = 5;
 	else
 		bits = 4;
 
-	if (ctrl->nand_version >= 0x0600) {
+	if (ctrl->nand_version >= 0x0702) {
+		if (cs >= 4)
+			reg = BRCMNAND_CORR_THRESHOLD_EXT;
+		shift = (cs % 4) * bits;
+	} else if (ctrl->nand_version >= 0x0600) {
 		if (cs >= 5)
 			reg = BRCMNAND_CORR_THRESHOLD_EXT;
 		shift = (cs % 5) * bits;
@@ -631,19 +671,28 @@ enum {
 
 static inline u32 brcmnand_spare_area_mask(struct brcmnand_controller *ctrl)
 {
-	if (ctrl->nand_version >= 0x0600)
+	if (ctrl->nand_version >= 0x0702)
+		return GENMASK(7, 0);
+	else if (ctrl->nand_version >= 0x0600)
 		return GENMASK(6, 0);
 	else
 		return GENMASK(5, 0);
 }
 
 #define NAND_ACC_CONTROL_ECC_SHIFT	16
+#define NAND_ACC_CONTROL_ECC_EXT_SHIFT	13
 
 static inline u32 brcmnand_ecc_level_mask(struct brcmnand_controller *ctrl)
 {
 	u32 mask = (ctrl->nand_version >= 0x0600) ? 0x1f : 0x0f;
 
-	return mask << NAND_ACC_CONTROL_ECC_SHIFT;
+	mask <<= NAND_ACC_CONTROL_ECC_SHIFT;
+
+	/* v7.2 includes additional ECC levels */
+	if (ctrl->nand_version >= 0x0702)
+		mask |= 0x7 << NAND_ACC_CONTROL_ECC_EXT_SHIFT;
+
+	return mask;
 }
 
 static void brcmnand_set_ecc_enabled(struct brcmnand_host *host, int en)
@@ -667,7 +716,9 @@ static void brcmnand_set_ecc_enabled(struct brcmnand_host *host, int en)
 
 static inline int brcmnand_sector_1k_shift(struct brcmnand_controller *ctrl)
 {
-	if (ctrl->nand_version >= 0x0600)
+	if (ctrl->nand_version >= 0x0702)
+		return 9;
+	else if (ctrl->nand_version >= 0x0600)
 		return 7;
 	else if (ctrl->nand_version >= 0x0500)
 		return 6;
@@ -773,10 +824,16 @@ enum brcmnand_llop_type {
  * Internal support functions
  ***********************************************************************/
 
-static inline bool is_hamming_ecc(struct brcmnand_cfg *cfg)
+static inline bool is_hamming_ecc(struct brcmnand_controller *ctrl,
+				  struct brcmnand_cfg *cfg)
 {
-	return cfg->sector_size_1k == 0 && cfg->spare_area_size == 16 &&
-		cfg->ecc_level == 15;
+	if (ctrl->nand_version <= 0x0701)
+		return cfg->sector_size_1k == 0 && cfg->spare_area_size == 16 &&
+			cfg->ecc_level == 15;
+	else
+		return cfg->sector_size_1k == 0 && ((cfg->spare_area_size == 16 &&
+			cfg->ecc_level == 15) ||
+			(cfg->spare_area_size == 28 && cfg->ecc_level == 16));
 }
 
 /*
@@ -931,7 +988,7 @@ static int brcmstb_choose_ecc_layout(struct brcmnand_host *host)
 	if (p->sector_size_1k)
 		ecc_level <<= 1;
 
-	if (is_hamming_ecc(p)) {
+	if (is_hamming_ecc(host->ctrl, p)) {
 		ecc->bytes = 3 * sectors;
 		mtd_set_ooblayout(mtd, &brcmnand_hamming_ooblayout_ops);
 		return 0;
@@ -1545,6 +1602,56 @@ static int brcmnand_read_by_pio(struct mtd_info *mtd, struct nand_chip *chip,
 	return ret;
 }
 
+/*
+ * Check a page to see if it is erased (w/ bitflips) after an uncorrectable ECC
+ * error
+ *
+ * Because the HW ECC signals an ECC error if an erase paged has even a single
+ * bitflip, we must check each ECC error to see if it is actually an erased
+ * page with bitflips, not a truly corrupted page.
+ *
+ * On a real error, return a negative error code (-EBADMSG for ECC error), and
+ * buf will contain raw data.
+ * Otherwise, buf gets filled with 0xffs and return the maximum number of
+ * bitflips-per-ECC-sector to the caller.
+ *
+ */
+static int brcmstb_nand_verify_erased_page(struct mtd_info *mtd,
+		  struct nand_chip *chip, void *buf, u64 addr)
+{
+	int i, sas;
+	void *oob = chip->oob_poi;
+	int bitflips = 0;
+	int page = addr >> chip->page_shift;
+	int ret;
+
+	if (!buf) {
+		buf = chip->buffers->databuf;
+		/* Invalidate page cache */
+		chip->pagebuf = -1;
+	}
+
+	sas = mtd->oobsize / chip->ecc.steps;
+
+	/* read without ecc for verification */
+	chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
+	ret = chip->ecc.read_page_raw(mtd, chip, buf, true, page);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < chip->ecc.steps; i++, oob += sas) {
+		ret = nand_check_erased_ecc_chunk(buf, chip->ecc.size,
+						  oob, sas, NULL, 0,
+						  chip->ecc.strength);
+		if (ret < 0)
+			return ret;
+
+		bitflips = max(bitflips, ret);
+	}
+
+	return bitflips;
+}
+
 static int brcmnand_read(struct mtd_info *mtd, struct nand_chip *chip,
 			 u64 addr, unsigned int trans, u32 *buf, u8 *oob)
 {
@@ -1552,9 +1659,11 @@ static int brcmnand_read(struct mtd_info *mtd, struct nand_chip *chip,
 	struct brcmnand_controller *ctrl = host->ctrl;
 	u64 err_addr = 0;
 	int err;
+	bool retry = true;
 
 	dev_dbg(ctrl->dev, "read %llx -> %p\n", (unsigned long long)addr, buf);
 
+try_dmaread:
 	brcmnand_write_reg(ctrl, BRCMNAND_UNCORR_COUNT, 0);
 
 	if (has_flash_dma(ctrl) && !oob && flash_dma_buf_ok(buf)) {
@@ -1575,6 +1684,34 @@ static int brcmnand_read(struct mtd_info *mtd, struct nand_chip *chip,
 	}
 
 	if (mtd_is_eccerr(err)) {
+		/*
+		 * On controller version and 7.0, 7.1 , DMA read after a
+		 * prior PIO read that reported uncorrectable error,
+		 * the DMA engine captures this error following DMA read
+		 * cleared only on subsequent DMA read, so just retry once
+		 * to clear a possible false error reported for current DMA
+		 * read
+		 */
+		if ((ctrl->nand_version == 0x0700) ||
+		    (ctrl->nand_version == 0x0701)) {
+			if (retry) {
+				retry = false;
+				goto try_dmaread;
+			}
+		}
+
+		/*
+		 * Controller version 7.2 has hw encoder to detect erased page
+		 * bitflips, apply sw verification for older controllers only
+		 */
+		if (ctrl->nand_version < 0x0702) {
+			err = brcmstb_nand_verify_erased_page(mtd, chip, buf,
+							      addr);
+			/* erased page bitflips corrected */
+			if (err > 0)
+				return err;
+		}
+
 		dev_dbg(ctrl->dev, "uncorrectable error at 0x%llx\n",
 			(unsigned long long)err_addr);
 		mtd->ecc_stats.failed++;
@@ -1857,7 +1994,8 @@ static int brcmnand_set_cfg(struct brcmnand_host *host,
 	return 0;
 }
 
-static void brcmnand_print_cfg(char *buf, struct brcmnand_cfg *cfg)
+static void brcmnand_print_cfg(struct brcmnand_host *host,
+			       char *buf, struct brcmnand_cfg *cfg)
 {
 	buf += sprintf(buf,
 		"%lluMiB total, %uKiB blocks, %u%s pages, %uB OOB, %u-bit",
@@ -1868,7 +2006,7 @@ static void brcmnand_print_cfg(char *buf, struct brcmnand_cfg *cfg)
 		cfg->spare_area_size, cfg->device_width);
 
 	/* Account for Hamming ECC and for BCH 512B vs 1KiB sectors */
-	if (is_hamming_ecc(cfg))
+	if (is_hamming_ecc(host->ctrl, cfg))
 		sprintf(buf, ", Hamming ECC");
 	else if (cfg->sector_size_1k)
 		sprintf(buf, ", BCH-%u (1KiB sector)", cfg->ecc_level << 1);
@@ -1987,7 +2125,7 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
 
 	brcmnand_set_ecc_enabled(host, 1);
 
-	brcmnand_print_cfg(msg, cfg);
+	brcmnand_print_cfg(host, msg, cfg);
 	dev_info(ctrl->dev, "detected %s\n", msg);
 
 	/* Configure ACC_CONTROL */
@@ -1995,6 +2133,10 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
 	tmp = nand_readreg(ctrl, offs);
 	tmp &= ~ACC_CONTROL_PARTIAL_PAGE;
 	tmp &= ~ACC_CONTROL_RD_ERASED;
+
+	/* We need to turn on Read from erased paged protected by ECC */
+	if (ctrl->nand_version >= 0x0702)
+		tmp |= ACC_CONTROL_RD_ERASED;
 	tmp &= ~ACC_CONTROL_FAST_PGM_RDIN;
 	if (ctrl->features & BRCMNAND_HAS_PREFETCH) {
 		/*
@@ -2195,6 +2337,7 @@ static const struct of_device_id brcmnand_of_match[] = {
 	{ .compatible = "brcm,brcmnand-v6.2" },
 	{ .compatible = "brcm,brcmnand-v7.0" },
 	{ .compatible = "brcm,brcmnand-v7.1" },
+	{ .compatible = "brcm,brcmnand-v7.2" },
 	{},
 };
 MODULE_DEVICE_TABLE(of, brcmnand_of_match);

drivers/mtd/nand/jz4780_bch.c

@@ -375,6 +375,6 @@ static struct platform_driver jz4780_bch_driver = {
 module_platform_driver(jz4780_bch_driver);
 
 MODULE_AUTHOR("Alex Smith <alex@alex-smith.me.uk>");
-MODULE_AUTHOR("Harvey Hunt <harvey.hunt@imgtec.com>");
+MODULE_AUTHOR("Harvey Hunt <harveyhuntnexus@gmail.com>");
 MODULE_DESCRIPTION("Ingenic JZ4780 BCH error correction driver");
 MODULE_LICENSE("GPL v2");

drivers/mtd/nand/jz4780_nand.c

@@ -412,6 +412,6 @@ static struct platform_driver jz4780_nand_driver = {
 module_platform_driver(jz4780_nand_driver);
 
 MODULE_AUTHOR("Alex Smith <alex@alex-smith.me.uk>");
-MODULE_AUTHOR("Harvey Hunt <harvey.hunt@imgtec.com>");
+MODULE_AUTHOR("Harvey Hunt <harveyhuntnexus@gmail.com>");
 MODULE_DESCRIPTION("Ingenic JZ4780 NAND driver");
 MODULE_LICENSE("GPL v2");

drivers/mtd/nand/mtk_ecc.h

+/*
+ * MTK SDG1 ECC controller
+ *
+ * Copyright (c) 2016 Mediatek
+ * Authors:	Xiaolei Li		<xiaolei.li@mediatek.com>
+ *		Jorge Ramirez-Ortiz	<jorge.ramirez-ortiz@linaro.org>
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#ifndef __DRIVERS_MTD_NAND_MTK_ECC_H__
+#define __DRIVERS_MTD_NAND_MTK_ECC_H__
+
+#include <linux/types.h>
+
+#define ECC_PARITY_BITS		(14)
+
+enum mtk_ecc_mode {ECC_DMA_MODE = 0, ECC_NFI_MODE = 1};
+enum mtk_ecc_operation {ECC_ENCODE, ECC_DECODE};
+
+struct device_node;
+struct mtk_ecc;
+
+struct mtk_ecc_stats {
+	u32 corrected;
+	u32 bitflips;
+	u32 failed;
+};
+
+struct mtk_ecc_config {
+	enum mtk_ecc_operation op;
+	enum mtk_ecc_mode mode;
+	dma_addr_t addr;
+	u32 strength;
+	u32 sectors;
+	u32 len;
+};
+
+int mtk_ecc_encode(struct mtk_ecc *, struct mtk_ecc_config *, u8 *, u32);
+void mtk_ecc_get_stats(struct mtk_ecc *, struct mtk_ecc_stats *, int);
+int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation);
+int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *);
+void mtk_ecc_disable(struct mtk_ecc *);
+void mtk_ecc_adjust_strength(u32 *);
+
+struct mtk_ecc *of_mtk_ecc_get(struct device_node *);
+void mtk_ecc_release(struct mtk_ecc *);
+
+#endif

drivers/mtd/nand/nand_ids.c

@@ -168,6 +168,7 @@ struct nand_flash_dev nand_flash_ids[] = {
 /* Manufacturer IDs */
 struct nand_manufacturers nand_manuf_ids[] = {
 	{NAND_MFR_TOSHIBA, "Toshiba"},
+	{NAND_MFR_ESMT, "ESMT"},
 	{NAND_MFR_SAMSUNG, "Samsung"},
 	{NAND_MFR_FUJITSU, "Fujitsu"},
 	{NAND_MFR_NATIONAL, "National"},

drivers/mtd/nand/omap2.c

@@ -118,8 +118,6 @@
 #define	PREFETCH_STATUS_FIFO_CNT(val)	((val >> 24) & 0x7F)
 #define	STATUS_BUFF_EMPTY		0x00000001
 
-#define OMAP24XX_DMA_GPMC		4
-
 #define SECTOR_BYTES		512
 /* 4 bit padding to make byte aligned, 56 = 52 + 4 */
 #define BCH4_BIT_PAD		4
@@ -1808,7 +1806,6 @@ static int omap_nand_probe(struct platform_device *pdev)
 	struct nand_chip		*nand_chip;
 	int				err;
 	dma_cap_mask_t			mask;
-	unsigned			sig;
 	struct resource			*res;
 	struct device			*dev = &pdev->dev;
 	int				min_oobbytes = BADBLOCK_MARKER_LENGTH;
@@ -1921,8 +1918,8 @@ static int omap_nand_probe(struct platform_device *pdev)
 	case NAND_OMAP_PREFETCH_DMA:
 		dma_cap_zero(mask);
 		dma_cap_set(DMA_SLAVE, mask);
-		sig = OMAP24XX_DMA_GPMC;
-		info->dma = dma_request_channel(mask, omap_dma_filter_fn, &sig);
+		info->dma = dma_request_chan(pdev->dev.parent, "rxtx");
+
 		if (!info->dma) {
 			dev_err(&pdev->dev, "DMA engine request failed\n");
 			err = -ENXIO;

drivers/mtd/nand/xway_nand.c

@@ -4,6 +4,7 @@
  *  by the Free Software Foundation.
  *
  *  Copyright © 2012 John Crispin <blogic@openwrt.org>
+ *  Copyright © 2016 Hauke Mehrtens <hauke@hauke-m.de>
  */
 
 #include <linux/mtd/nand.h>
@@ -16,20 +17,28 @@
 #define EBU_ADDSEL1		0x24
 #define EBU_NAND_CON		0xB0
 #define EBU_NAND_WAIT		0xB4
+#define  NAND_WAIT_RD		BIT(0) /* NAND flash status output */
+#define  NAND_WAIT_WR_C		BIT(3) /* NAND Write/Read complete */
 #define EBU_NAND_ECC0		0xB8
 #define EBU_NAND_ECC_AC		0xBC
 
-/* nand commands */
-#define NAND_CMD_ALE		(1 << 2)
-#define NAND_CMD_CLE		(1 << 3)
-#define NAND_CMD_CS		(1 << 4)
-#define NAND_WRITE_CMD_RESET	0xff
+/*
+ * nand commands
+ * The pins of the NAND chip are selected based on the address bits of the
+ * "register" read and write. There are no special registers, but an
+ * address range and the lower address bits are used to activate the
+ * correct line. For example when the bit (1 << 2) is set in the address
+ * the ALE pin will be activated.
+ */
+#define NAND_CMD_ALE		BIT(2) /* address latch enable */
+#define NAND_CMD_CLE		BIT(3) /* command latch enable */
+#define NAND_CMD_CS		BIT(4) /* chip select */
+#define NAND_CMD_SE		BIT(5) /* spare area access latch */
+#define NAND_CMD_WP		BIT(6) /* write protect */
 #define NAND_WRITE_CMD		(NAND_CMD_CS | NAND_CMD_CLE)
 #define NAND_WRITE_ADDR		(NAND_CMD_CS | NAND_CMD_ALE)
 #define NAND_WRITE_DATA		(NAND_CMD_CS)
 #define NAND_READ_DATA		(NAND_CMD_CS)
-#define NAND_WAIT_WR_C		(1 << 3)
-#define NAND_WAIT_RD		(0x1)
 
 /* we need to tel the ebu which addr we mapped the nand to */
 #define ADDSEL1_MASK(x)		(x << 4)
@@ -54,31 +63,41 @@
 #define NAND_CON_CSMUX		(1 << 1)
 #define NAND_CON_NANDM		1
 
-static void xway_reset_chip(struct nand_chip *chip)
+struct xway_nand_data {
+	struct nand_chip	chip;
+	unsigned long		csflags;
+	void __iomem		*nandaddr;
+};
+
+static u8 xway_readb(struct mtd_info *mtd, int op)
 {
-	unsigned long nandaddr = (unsigned long) chip->IO_ADDR_W;
-	unsigned long flags;
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct xway_nand_data *data = nand_get_controller_data(chip);
 
-	nandaddr &= ~NAND_WRITE_ADDR;
-	nandaddr |= NAND_WRITE_CMD;
+	return readb(data->nandaddr + op);
+}
 
-	/* finish with a reset */
-	spin_lock_irqsave(&ebu_lock, flags);
-	writeb(NAND_WRITE_CMD_RESET, (void __iomem *) nandaddr);
-	while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0)
-		;
-	spin_unlock_irqrestore(&ebu_lock, flags);
+static void xway_writeb(struct mtd_info *mtd, int op, u8 value)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct xway_nand_data *data = nand_get_controller_data(chip);
+
+	writeb(value, data->nandaddr + op);
 }
 
-static void xway_select_chip(struct mtd_info *mtd, int chip)
+static void xway_select_chip(struct mtd_info *mtd, int select)
 {
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct xway_nand_data *data = nand_get_controller_data(chip);
 
-	switch (chip) {
+	switch (select) {
 	case -1:
 		ltq_ebu_w32_mask(NAND_CON_CE, 0, EBU_NAND_CON);
 		ltq_ebu_w32_mask(NAND_CON_NANDM, 0, EBU_NAND_CON);
+		spin_unlock_irqrestore(&ebu_lock, data->csflags);
 		break;
 	case 0:
+		spin_lock_irqsave(&ebu_lock, data->csflags);
 		ltq_ebu_w32_mask(0, NAND_CON_NANDM, EBU_NAND_CON);
 		ltq_ebu_w32_mask(0, NAND_CON_CE, EBU_NAND_CON);
 		break;
@@ -89,26 +108,16 @@ static void xway_select_chip(struct mtd_info *mtd, int chip)
 
 static void xway_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 {
-	struct nand_chip *this = mtd_to_nand(mtd);
-	unsigned long nandaddr = (unsigned long) this->IO_ADDR_W;
-	unsigned long flags;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		nandaddr &= ~(NAND_WRITE_CMD | NAND_WRITE_ADDR);
-		if (ctrl & NAND_CLE)
-			nandaddr |= NAND_WRITE_CMD;
-		else
-			nandaddr |= NAND_WRITE_ADDR;
-		this->IO_ADDR_W = (void __iomem *) nandaddr;
-	}
+	if (cmd == NAND_CMD_NONE)
+		return;
 
-	if (cmd != NAND_CMD_NONE) {
-		spin_lock_irqsave(&ebu_lock, flags);
-		writeb(cmd, this->IO_ADDR_W);
-		while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0)
-			;
-		spin_unlock_irqrestore(&ebu_lock, flags);
-	}
+	if (ctrl & NAND_CLE)
+		xway_writeb(mtd, NAND_WRITE_CMD, cmd);
+	else if (ctrl & NAND_ALE)
+		xway_writeb(mtd, NAND_WRITE_ADDR, cmd);
+
+	while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0)
+		;
 }
 
 static int xway_dev_ready(struct mtd_info *mtd)
@@ -118,80 +127,122 @@ static int xway_dev_ready(struct mtd_info *mtd)
 
 static unsigned char xway_read_byte(struct mtd_info *mtd)
 {
-	struct nand_chip *this = mtd_to_nand(mtd);
-	unsigned long nandaddr = (unsigned long) this->IO_ADDR_R;
-	unsigned long flags;
-	int ret;
+	return xway_readb(mtd, NAND_READ_DATA);
+}
+
+static void xway_read_buf(struct mtd_info *mtd, u_char *buf, int len)
+{
+	int i;
 
-	spin_lock_irqsave(&ebu_lock, flags);
-	ret = ltq_r8((void __iomem *)(nandaddr + NAND_READ_DATA));
-	spin_unlock_irqrestore(&ebu_lock, flags);
+	for (i = 0; i < len; i++)
+		buf[i] = xway_readb(mtd, NAND_WRITE_DATA);
+}
 
-	return ret;
+static void xway_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i++)
+		xway_writeb(mtd, NAND_WRITE_DATA, buf[i]);
 }
 
+/*
+ * Probe for the NAND device.
+ */
 static int xway_nand_probe(struct platform_device *pdev)
 {
-	struct nand_chip *this = platform_get_drvdata(pdev);
-	unsigned long nandaddr = (unsigned long) this->IO_ADDR_W;
-	const __be32 *cs = of_get_property(pdev->dev.of_node,
-					"lantiq,cs", NULL);
+	struct xway_nand_data *data;
+	struct mtd_info *mtd;
+	struct resource *res;
+	int err;
+	u32 cs;
 	u32 cs_flag = 0;
 
+	/* Allocate memory for the device structure (and zero it) */
+	data = devm_kzalloc(&pdev->dev, sizeof(struct xway_nand_data),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	data->nandaddr = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(data->nandaddr))
+		return PTR_ERR(data->nandaddr);
+
+	nand_set_flash_node(&data->chip, pdev->dev.of_node);
+	mtd = nand_to_mtd(&data->chip);
+	mtd->dev.parent = &pdev->dev;
+
+	data->chip.cmd_ctrl = xway_cmd_ctrl;
+	data->chip.dev_ready = xway_dev_ready;
+	data->chip.select_chip = xway_select_chip;
+	data->chip.write_buf = xway_write_buf;
+	data->chip.read_buf = xway_read_buf;
+	data->chip.read_byte = xway_read_byte;
+	data->chip.chip_delay = 30;
+
+	data->chip.ecc.mode = NAND_ECC_SOFT;
+	data->chip.ecc.algo = NAND_ECC_HAMMING;
+
+	platform_set_drvdata(pdev, data);
+	nand_set_controller_data(&data->chip, data);
+
 	/* load our CS from the DT. Either we find a valid 1 or default to 0 */
-	if (cs && (*cs == 1))
+	err = of_property_read_u32(pdev->dev.of_node, "lantiq,cs", &cs);
+	if (!err && cs == 1)
 		cs_flag = NAND_CON_IN_CS1 | NAND_CON_OUT_CS1;
 
 	/* setup the EBU to run in NAND mode on our base addr */
-	ltq_ebu_w32(CPHYSADDR(nandaddr)
-		| ADDSEL1_MASK(3) | ADDSEL1_REGEN, EBU_ADDSEL1);
+	ltq_ebu_w32(CPHYSADDR(data->nandaddr)
+		    | ADDSEL1_MASK(3) | ADDSEL1_REGEN, EBU_ADDSEL1);
 
 	ltq_ebu_w32(BUSCON1_SETUP | BUSCON1_BCGEN_RES | BUSCON1_WAITWRC2
-		| BUSCON1_WAITRDC2 | BUSCON1_HOLDC1 | BUSCON1_RECOVC1
-		| BUSCON1_CMULT4, LTQ_EBU_BUSCON1);
+		    | BUSCON1_WAITRDC2 | BUSCON1_HOLDC1 | BUSCON1_RECOVC1
+		    | BUSCON1_CMULT4, LTQ_EBU_BUSCON1);
 
 	ltq_ebu_w32(NAND_CON_NANDM | NAND_CON_CSMUX | NAND_CON_CS_P
-		| NAND_CON_SE_P | NAND_CON_WP_P | NAND_CON_PRE_P
-		| cs_flag, EBU_NAND_CON);
+		    | NAND_CON_SE_P | NAND_CON_WP_P | NAND_CON_PRE_P
+		    | cs_flag, EBU_NAND_CON);
 
-	/* finish with a reset */
-	xway_reset_chip(this);
+	/* Scan to find existence of the device */
+	err = nand_scan(mtd, 1);
+	if (err)
+		return err;
 
-	return 0;
-}
+	err = mtd_device_register(mtd, NULL, 0);
+	if (err)
+		nand_release(mtd);
 
-static struct platform_nand_data xway_nand_data = {
-	.chip = {
-		.nr_chips		= 1,
-		.chip_delay		= 30,
-	},
-	.ctrl = {
-		.probe		= xway_nand_probe,
-		.cmd_ctrl	= xway_cmd_ctrl,
-		.dev_ready	= xway_dev_ready,
-		.select_chip	= xway_select_chip,
-		.read_byte	= xway_read_byte,
-	}
-};
+	return err;
+}
 
 /*
- * Try to find the node inside the DT. If it is available attach out
- * platform_nand_data
+ * Remove a NAND device.
  */
-static int __init xway_register_nand(void)
+static int xway_nand_remove(struct platform_device *pdev)
 {
-	struct device_node *node;
-	struct platform_device *pdev;
-
-	node = of_find_compatible_node(NULL, NULL, "lantiq,nand-xway");
-	if (!node)
-		return -ENOENT;
-	pdev = of_find_device_by_node(node);
-	if (!pdev)
-		return -EINVAL;
-	pdev->dev.platform_data = &xway_nand_data;
-	of_node_put(node);
+	struct xway_nand_data *data = platform_get_drvdata(pdev);
+
+	nand_release(nand_to_mtd(&data->chip));
+
 	return 0;
 }
 
-subsys_initcall(xway_register_nand);
+static const struct of_device_id xway_nand_match[] = {
+	{ .compatible = "lantiq,nand-xway" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xway_nand_match);
+
+static struct platform_driver xway_nand_driver = {
+	.probe	= xway_nand_probe,
+	.remove	= xway_nand_remove,
+	.driver	= {
+		.name		= "lantiq,nand-xway",
+		.of_match_table = xway_nand_match,
+	},
+};
+
+module_platform_driver(xway_nand_driver);
+
+MODULE_LICENSE("GPL");

drivers/mtd/tests/nandbiterrs.c

@@ -290,7 +290,7 @@ static int overwrite_test(void)
 
 	while (opno < max_overwrite) {
 
-		err = rewrite_page(0);
+		err = write_page(0);
 		if (err)
 			break;
 

include/linux/mtd/nand.h

@@ -783,6 +783,7 @@ static inline void nand_set_controller_data(struct nand_chip *chip, void *priv)
  * NAND Flash Manufacturer ID Codes
  */
 #define NAND_MFR_TOSHIBA	0x98
+#define NAND_MFR_ESMT		0xc8
 #define NAND_MFR_SAMSUNG	0xec
 #define NAND_MFR_FUJITSU	0x04
 #define NAND_MFR_NATIONAL	0x8f