Commit 1f940386 authored by Luciano Coelho's avatar Luciano Coelho Committed by Emmanuel Grumbach

iwlwifi: mvm: remove deprecated scan API code

The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions.  Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: default avatarLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: default avatarEmmanuel Grumbach <emmanuel.grumbach@intel.com>
parent 1e2c24f0
......@@ -237,7 +237,6 @@ enum iwl_ucode_tlv_flag {
* enum iwl_ucode_tlv_api - ucode api
* @IWL_UCODE_TLV_API_BT_COEX_SPLIT: new API for BT Coex
* @IWL_UCODE_TLV_API_DISABLE_STA_TX: ucode supports tx_disable bit.
* @IWL_UCODE_TLV_API_LMAC_SCAN: This ucode uses LMAC unified scan API.
* @IWL_UCODE_TLV_API_SF_NO_DUMMY_NOTIF: ucode supports disabling dummy notif.
* @IWL_UCODE_TLV_API_FRAGMENTED_SCAN: This ucode supports active dwell time
* longer than the passive one, which is essential for fragmented scan.
......@@ -255,7 +254,6 @@ enum iwl_ucode_tlv_flag {
enum iwl_ucode_tlv_api {
IWL_UCODE_TLV_API_BT_COEX_SPLIT = BIT(3),
IWL_UCODE_TLV_API_DISABLE_STA_TX = BIT(5),
IWL_UCODE_TLV_API_LMAC_SCAN = BIT(6),
IWL_UCODE_TLV_API_SF_NO_DUMMY_NOTIF = BIT(7),
IWL_UCODE_TLV_API_FRAGMENTED_SCAN = BIT(8),
IWL_UCODE_TLV_API_HDC_PHASE_0 = BIT(10),
......
......@@ -70,54 +70,9 @@
/* Scan Commands, Responses, Notifications */
/* Masks for iwl_scan_channel.type flags */
#define SCAN_CHANNEL_TYPE_ACTIVE BIT(0)
#define SCAN_CHANNEL_NARROW_BAND BIT(22)
/* Max number of IEs for direct SSID scans in a command */
#define PROBE_OPTION_MAX 20
/**
* struct iwl_scan_channel - entry in REPLY_SCAN_CMD channel table
* @channel: band is selected by iwl_scan_cmd "flags" field
* @tx_gain: gain for analog radio
* @dsp_atten: gain for DSP
* @active_dwell: dwell time for active scan in TU, typically 5-50
* @passive_dwell: dwell time for passive scan in TU, typically 20-500
* @type: type is broken down to these bits:
* bit 0: 0 = passive, 1 = active
* bits 1-20: SSID direct bit map. If any of these bits is set then
* the corresponding SSID IE is transmitted in probe request
* (bit i adds IE in position i to the probe request)
* bit 22: channel width, 0 = regular, 1 = TGj narrow channel
*
* @iteration_count:
* @iteration_interval:
* This struct is used once for each channel in the scan list.
* Each channel can independently select:
* 1) SSID for directed active scans
* 2) Txpower setting (for rate specified within Tx command)
* 3) How long to stay on-channel (behavior may be modified by quiet_time,
* quiet_plcp_th, good_CRC_th)
*
* To avoid uCode errors, make sure the following are true (see comments
* under struct iwl_scan_cmd about max_out_time and quiet_time):
* 1) If using passive_dwell (i.e. passive_dwell != 0):
* active_dwell <= passive_dwell (< max_out_time if max_out_time != 0)
* 2) quiet_time <= active_dwell
* 3) If restricting off-channel time (i.e. max_out_time !=0):
* passive_dwell < max_out_time
* active_dwell < max_out_time
*/
struct iwl_scan_channel {
__le32 type;
__le16 channel;
__le16 iteration_count;
__le32 iteration_interval;
__le16 active_dwell;
__le16 passive_dwell;
} __packed; /* SCAN_CHANNEL_CONTROL_API_S_VER_1 */
/**
* struct iwl_ssid_ie - directed scan network information element
*
......@@ -132,152 +87,6 @@ struct iwl_ssid_ie {
u8 ssid[IEEE80211_MAX_SSID_LEN];
} __packed; /* SCAN_DIRECT_SSID_IE_API_S_VER_1 */
/**
* iwl_scan_flags - masks for scan command flags
*@SCAN_FLAGS_PERIODIC_SCAN:
*@SCAN_FLAGS_P2P_PUBLIC_ACTION_FRAME_TX:
*@SCAN_FLAGS_DELAYED_SCAN_LOWBAND:
*@SCAN_FLAGS_DELAYED_SCAN_HIGHBAND:
*@SCAN_FLAGS_FRAGMENTED_SCAN:
*@SCAN_FLAGS_PASSIVE2ACTIVE: use active scan on channels that was active
* in the past hour, even if they are marked as passive.
*/
enum iwl_scan_flags {
SCAN_FLAGS_PERIODIC_SCAN = BIT(0),
SCAN_FLAGS_P2P_PUBLIC_ACTION_FRAME_TX = BIT(1),
SCAN_FLAGS_DELAYED_SCAN_LOWBAND = BIT(2),
SCAN_FLAGS_DELAYED_SCAN_HIGHBAND = BIT(3),
SCAN_FLAGS_FRAGMENTED_SCAN = BIT(4),
SCAN_FLAGS_PASSIVE2ACTIVE = BIT(5),
};
/**
* enum iwl_scan_type - Scan types for scan command
* @SCAN_TYPE_FORCED:
* @SCAN_TYPE_BACKGROUND:
* @SCAN_TYPE_OS:
* @SCAN_TYPE_ROAMING:
* @SCAN_TYPE_ACTION:
* @SCAN_TYPE_DISCOVERY:
* @SCAN_TYPE_DISCOVERY_FORCED:
*/
enum iwl_scan_type {
SCAN_TYPE_FORCED = 0,
SCAN_TYPE_BACKGROUND = 1,
SCAN_TYPE_OS = 2,
SCAN_TYPE_ROAMING = 3,
SCAN_TYPE_ACTION = 4,
SCAN_TYPE_DISCOVERY = 5,
SCAN_TYPE_DISCOVERY_FORCED = 6,
}; /* SCAN_ACTIVITY_TYPE_E_VER_1 */
/**
* struct iwl_scan_cmd - scan request command
* ( SCAN_REQUEST_CMD = 0x80 )
* @len: command length in bytes
* @scan_flags: scan flags from SCAN_FLAGS_*
* @channel_count: num of channels in channel list
* (1 - ucode_capa.n_scan_channels)
* @quiet_time: in msecs, dwell this time for active scan on quiet channels
* @quiet_plcp_th: quiet PLCP threshold (channel is quiet if less than
* this number of packets were received (typically 1)
* @passive2active: is auto switching from passive to active during scan allowed
* @rxchain_sel_flags: RXON_RX_CHAIN_*
* @max_out_time: in TUs, max out of serving channel time
* @suspend_time: how long to pause scan when returning to service channel:
* bits 0-19: beacon interal in TUs (suspend before executing)
* bits 20-23: reserved
* bits 24-31: number of beacons (suspend between channels)
* @rxon_flags: RXON_FLG_*
* @filter_flags: RXON_FILTER_*
* @tx_cmd: for active scans (zero for passive), w/o payload,
* no RS so specify TX rate
* @direct_scan: direct scan SSIDs
* @type: one of SCAN_TYPE_*
* @repeats: how many time to repeat the scan
*/
struct iwl_scan_cmd {
__le16 len;
u8 scan_flags;
u8 channel_count;
__le16 quiet_time;
__le16 quiet_plcp_th;
__le16 passive2active;
__le16 rxchain_sel_flags;
__le32 max_out_time;
__le32 suspend_time;
/* RX_ON_FLAGS_API_S_VER_1 */
__le32 rxon_flags;
__le32 filter_flags;
struct iwl_tx_cmd tx_cmd;
struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX];
__le32 type;
__le32 repeats;
/*
* Probe request frame, followed by channel list.
*
* Size of probe request frame is specified by byte count in tx_cmd.
* Channel list follows immediately after probe request frame.
* Number of channels in list is specified by channel_count.
* Each channel in list is of type:
*
* struct iwl_scan_channel channels[0];
*
* NOTE: Only one band of channels can be scanned per pass. You
* must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
* for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
* before requesting another scan.
*/
u8 data[0];
} __packed; /* SCAN_REQUEST_FIXED_PART_API_S_VER_5 */
/* Response to scan request contains only status with one of these values */
#define SCAN_RESPONSE_OK 0x1
#define SCAN_RESPONSE_ERROR 0x2
/*
* SCAN_ABORT_CMD = 0x81
* When scan abort is requested, the command has no fields except the common
* header. The response contains only a status with one of these values.
*/
#define SCAN_ABORT_POSSIBLE 0x1
#define SCAN_ABORT_IGNORED 0x2 /* no pending scans */
/* TODO: complete documentation */
#define SCAN_OWNER_STATUS 0x1
#define MEASURE_OWNER_STATUS 0x2
/**
* struct iwl_scan_start_notif - notifies start of scan in the device
* ( SCAN_START_NOTIFICATION = 0x82 )
* @tsf_low: TSF timer (lower half) in usecs
* @tsf_high: TSF timer (higher half) in usecs
* @beacon_timer: structured as follows:
* bits 0:19 - beacon interval in usecs
* bits 20:23 - reserved (0)
* bits 24:31 - number of beacons
* @channel: which channel is scanned
* @band: 0 for 5.2 GHz, 1 for 2.4 GHz
* @status: one of *_OWNER_STATUS
*/
struct iwl_scan_start_notif {
__le32 tsf_low;
__le32 tsf_high;
__le32 beacon_timer;
u8 channel;
u8 band;
u8 reserved[2];
__le32 status;
} __packed; /* SCAN_START_NTF_API_S_VER_1 */
/* scan results probe_status first bit indicates success */
#define SCAN_PROBE_STATUS_OK 0
#define SCAN_PROBE_STATUS_TX_FAILED BIT(0)
/* error statuses combined with TX_FAILED */
#define SCAN_PROBE_STATUS_FAIL_TTL BIT(1)
#define SCAN_PROBE_STATUS_FAIL_BT BIT(2)
/* How many statistics are gathered for each channel */
#define SCAN_RESULTS_STATISTICS 1
......
......@@ -339,13 +339,10 @@ int iwl_mvm_mac_setup_register(struct iwl_mvm *mvm)
!iwlwifi_mod_params.sw_crypto)
hw->flags |= IEEE80211_HW_MFP_CAPABLE;
if (mvm->fw->ucode_capa.api[0] & IWL_UCODE_TLV_API_LMAC_SCAN ||
mvm->fw->ucode_capa.capa[0] & IWL_UCODE_TLV_CAPA_UMAC_SCAN) {
hw->flags |= IEEE80211_SINGLE_HW_SCAN_ON_ALL_BANDS;
hw->wiphy->features |=
NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR |
NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR;
}
hw->flags |= IEEE80211_SINGLE_HW_SCAN_ON_ALL_BANDS;
hw->wiphy->features |=
NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR |
NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR;
hw->sta_data_size = sizeof(struct iwl_mvm_sta);
hw->vif_data_size = sizeof(struct iwl_mvm_vif);
......@@ -2204,10 +2201,8 @@ static int iwl_mvm_mac_hw_scan(struct ieee80211_hw *hw,
if (mvm->fw->ucode_capa.capa[0] & IWL_UCODE_TLV_CAPA_UMAC_SCAN)
ret = iwl_mvm_scan_umac(mvm, vif, hw_req);
else if (mvm->fw->ucode_capa.api[0] & IWL_UCODE_TLV_API_LMAC_SCAN)
ret = iwl_mvm_unified_scan_lmac(mvm, vif, hw_req);
else
ret = iwl_mvm_scan_request(mvm, vif, req);
ret = iwl_mvm_unified_scan_lmac(mvm, vif, hw_req);
if (ret)
iwl_mvm_unref(mvm, IWL_MVM_REF_SCAN);
......@@ -2535,13 +2530,7 @@ static int iwl_mvm_mac_sched_scan_start(struct ieee80211_hw *hw,
mutex_lock(&mvm->mutex);
/* Newest FW fixes sched scan while connected on another interface */
if (mvm->fw->ucode_capa.api[0] & IWL_UCODE_TLV_API_LMAC_SCAN) {
if (!vif->bss_conf.idle) {
ret = -EBUSY;
goto out;
}
} else if (!iwl_mvm_is_idle(mvm)) {
if (!vif->bss_conf.idle) {
ret = -EBUSY;
goto out;
}
......
......@@ -1080,13 +1080,6 @@ int iwl_mvm_update_quotas(struct iwl_mvm *mvm,
/* Scanning */
int iwl_mvm_scan_size(struct iwl_mvm *mvm);
int iwl_mvm_scan_request(struct iwl_mvm *mvm,
struct ieee80211_vif *vif,
struct cfg80211_scan_request *req);
int iwl_mvm_rx_scan_response(struct iwl_mvm *mvm, struct iwl_rx_cmd_buffer *rxb,
struct iwl_device_cmd *cmd);
int iwl_mvm_rx_scan_complete(struct iwl_mvm *mvm, struct iwl_rx_cmd_buffer *rxb,
struct iwl_device_cmd *cmd);
int iwl_mvm_cancel_scan(struct iwl_mvm *mvm);
int iwl_mvm_max_scan_ie_len(struct iwl_mvm *mvm, bool is_sched_scan);
......@@ -1097,14 +1090,8 @@ int iwl_mvm_rx_scan_offload_complete_notif(struct iwl_mvm *mvm,
int iwl_mvm_rx_scan_offload_iter_complete_notif(struct iwl_mvm *mvm,
struct iwl_rx_cmd_buffer *rxb,
struct iwl_device_cmd *cmd);
int iwl_mvm_config_sched_scan(struct iwl_mvm *mvm,
struct ieee80211_vif *vif,
struct cfg80211_sched_scan_request *req,
struct ieee80211_scan_ies *ies);
int iwl_mvm_config_sched_scan_profiles(struct iwl_mvm *mvm,
struct cfg80211_sched_scan_request *req);
int iwl_mvm_sched_scan_start(struct iwl_mvm *mvm,
struct cfg80211_sched_scan_request *req);
int iwl_mvm_scan_offload_start(struct iwl_mvm *mvm,
struct ieee80211_vif *vif,
struct cfg80211_sched_scan_request *req,
......@@ -1359,9 +1346,6 @@ static inline void iwl_mvm_enable_agg_txq(struct iwl_mvm *mvm, int queue,
iwl_mvm_enable_txq(mvm, queue, ssn, &cfg, wdg_timeout);
}
/* Assoc status */
bool iwl_mvm_is_idle(struct iwl_mvm *mvm);
/* Thermal management and CT-kill */
void iwl_mvm_tt_tx_backoff(struct iwl_mvm *mvm, u32 backoff);
void iwl_mvm_tt_temp_changed(struct iwl_mvm *mvm, u32 temp);
......
......@@ -237,8 +237,6 @@ static const struct iwl_rx_handlers iwl_mvm_rx_handlers[] = {
RX_HANDLER(EOSP_NOTIFICATION, iwl_mvm_rx_eosp_notif, false),
RX_HANDLER(SCAN_REQUEST_CMD, iwl_mvm_rx_scan_response, false),
RX_HANDLER(SCAN_COMPLETE_NOTIFICATION, iwl_mvm_rx_scan_complete, true),
RX_HANDLER(SCAN_ITERATION_COMPLETE,
iwl_mvm_rx_scan_offload_iter_complete_notif, false),
RX_HANDLER(SCAN_OFFLOAD_COMPLETE,
......
This diff is collapsed.
......@@ -746,25 +746,6 @@ bool iwl_mvm_low_latency(struct iwl_mvm *mvm)
return result;
}
static void iwl_mvm_idle_iter(void *_data, u8 *mac, struct ieee80211_vif *vif)
{
bool *idle = _data;
if (!vif->bss_conf.idle)
*idle = false;
}
bool iwl_mvm_is_idle(struct iwl_mvm *mvm)
{
bool idle = true;
ieee80211_iterate_active_interfaces_atomic(
mvm->hw, IEEE80211_IFACE_ITER_NORMAL,
iwl_mvm_idle_iter, &idle);
return idle;
}
struct iwl_bss_iter_data {
struct ieee80211_vif *vif;
bool error;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment