Commit 2064c946 authored by Adrian Bunk's avatar Adrian Bunk Committed by Bartlomiej Zolnierkiewicz

ARM: always select HAVE_IDE

It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h

It turns out this was done for ARM, and we can simply always select 
HAVE_IDE on ARM instead of manually tracking which platforms might 
possible have an IDE controller directly or indirectly.
Signed-off-by: default avatarAdrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent 3f31b874
......@@ -8,6 +8,7 @@ mainmenu "Linux Kernel Configuration"
config ARM
bool
default y
select HAVE_IDE
select RTC_LIB
select SYS_SUPPORTS_APM_EMULATION
select HAVE_OPROFILE
......@@ -223,7 +224,6 @@ config ARCH_CLPS7500
select TIMER_ACORN
select ISA
select NO_IOPORT
select HAVE_IDE
help
Support for the Cirrus Logic PS7500FE system-on-a-chip.
......@@ -236,7 +236,6 @@ config ARCH_CO285
bool "Co-EBSA285"
select FOOTBRIDGE
select FOOTBRIDGE_ADDIN
select HAVE_IDE
help
Support for Intel's EBSA285 companion chip.
......@@ -262,7 +261,6 @@ config ARCH_EP93XX
config ARCH_FOOTBRIDGE
bool "FootBridge"
select FOOTBRIDGE
select HAVE_IDE
help
Support for systems based on the DC21285 companion chip
("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
......@@ -301,7 +299,6 @@ config ARCH_IOP32X
depends on MMU
select PLAT_IOP
select PCI
select HAVE_IDE
help
Support for Intel's 80219 and IOP32X (XScale) family of
processors.
......@@ -311,14 +308,12 @@ config ARCH_IOP33X
depends on MMU
select PLAT_IOP
select PCI
select HAVE_IDE
help
Support for Intel's IOP33X (XScale) family of processors.
config ARCH_IXP23XX
bool "IXP23XX-based"
depends on MMU
select HAVE_IDE
select PCI
help
Support for Intel's IXP23xx (XScale) family of processors.
......@@ -336,14 +331,12 @@ config ARCH_IXP4XX
select GENERIC_GPIO
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_IDE
help
Support for Intel's IXP4XX (XScale) family of processors.
config ARCH_L7200
bool "LinkUp-L7200"
select FIQ
select HAVE_IDE
help
Say Y here if you intend to run this kernel on a LinkUp Systems
L7200 Software Development Board which uses an ARM720T processor.
......@@ -400,7 +393,6 @@ config ARCH_PXA
depends on MMU
select ARCH_MTD_XIP
select GENERIC_GPIO
select HAVE_IDE
select HAVE_GPIO_LIB
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
......@@ -416,7 +408,6 @@ config ARCH_RPC
select ARCH_MAY_HAVE_PC_FDC
select ISA_DMA_API
select NO_IOPORT
select HAVE_IDE
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
......@@ -432,7 +423,6 @@ config ARCH_SA1100
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select TICK_ONESHOT
select HAVE_IDE
select HAVE_GPIO_LIB
help
Support for StrongARM 11x0 based boards.
......@@ -440,7 +430,6 @@ config ARCH_SA1100
config ARCH_S3C2410
bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443"
select GENERIC_GPIO
select HAVE_IDE
help
Samsung S3C2410X CPU based systems, such as the Simtec Electronics
BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
......@@ -448,7 +437,6 @@ config ARCH_S3C2410
config ARCH_SHARK
bool "Shark"
select HAVE_IDE
select ISA
select ISA_DMA
select PCI
......@@ -458,7 +446,6 @@ config ARCH_SHARK
config ARCH_LH7A40X
bool "Sharp LH7A40X"
select HAVE_IDE
help
Say Y here for systems based on one of the Sharp LH7A40X
System on a Chip processors. These CPUs include an ARM922T
......
......@@ -38,7 +38,6 @@ config PCMCIA_DEBUG
config PCMCIA
tristate "16-bit PCMCIA support"
select CRC32
select HAVE_IDE
default y
---help---
This option enables support for 16-bit PCMCIA cards. Most older
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment