Merge tag 'v6.8-rockchip-dts64-2' of...

Merge tag 'v6.8-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt

One new boards, the CoolPi CM5 SoM and 4B SBC. Basic node for the rk3588
display controller and a bunch of small improvements for different boards,

* tag 'v6.8-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
  arm64: dts: rockchip: Fix led pinctrl of lubancat 1
  arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
  arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
  arm64: dts: rockchip: support poweroff on the rock-5b
  arm64: dts: rockchip: Support poweroff on Orange Pi 5
  arm64: dts: rockchip: nanopc-t6 sdmmc beautification
  arm64: dts: rockchip: Fix rk3588 USB power-domain clocks
  arm64: dts: rockchip: configure eth pad driver strength for orangepi r1 plus lts
  arm64: dts: rockchip: Support poweroff on NanoPC-T6
  arm64: dts: rockchip: rk3308-rock-pi-s gpio-line-names cleanup
  arm64: dts: rockchip: Add support for rk3588 based board Cool Pi CM5 EVB
  dt-bindings: arm: rockchip: Add Cool Pi CM5
  arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B
  dt-bindings: arm: rockchip: Add Cool Pi 4B
  dt-bindings: vendor-prefixes: Add Cool Pi
  arm64: dts: rockchip: add gpio-line-names to rk3328-rock-pi-e
  arm64: dts: rockchip: make use gpio-keys for buttons on puma-haikou
  arm64: dts: rockchip: expose BIOS Disable feedback pin on rk3399-puma
  arm64: dts: rockchip: fix misleading comment in rk3399-puma-haikou.dts
  arm64: dts: rockchip: Add vop on rk3588
  ...

Link: https://lore.kernel.org/r/3711719.VqM8IeB0Os@diegoSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/rockchip.yaml

@@ -97,6 +97,18 @@ properties:
           - const: chipspark,rayeager-px2
           - const: rockchip,rk3066a
 
+      - description: Cool Pi Compute Module 5(CM5) EVB
+        items:
+          - enum:
+              - coolpi,pi-cm5-evb
+          - const: coolpi,pi-cm5
+          - const: rockchip,rk3588
+
+      - description: Cool Pi 4 Model B
+        items:
+          - const: coolpi,pi-4b
+          - const: rockchip,rk3588s
+
       - description: Edgeble Neural Compute Module 2(Neu2) SoM based boards
         items:
           - const: edgeble,neural-compute-module-2-io   # Edgeble Neural Compute Module 2 IO Board

Documentation/devicetree/bindings/soc/rockchip/grf.yaml

@@ -28,6 +28,8 @@ properties:
               - rockchip,rk3588-sys-grf
               - rockchip,rk3588-pcie3-phy-grf
               - rockchip,rk3588-pcie3-pipe-grf
+              - rockchip,rk3588-vo-grf
+              - rockchip,rk3588-vop-grf
               - rockchip,rv1108-usbgrf
           - const: syscon
       - items:

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -294,6 +294,8 @@ patternProperties:
     description: CompuLab Ltd.
   "^congatec,.*":
     description: congatec GmbH
+  "^coolpi,.*":
+    description: cool-pi.com
   "^coreriver,.*":
     description: CORERIVER Semiconductor Co.,Ltd.
   "^corpro,.*":

arch/arm64/boot/dts/rockchip/Makefile

@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-coolpi-cm5-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb
@@ -110,6 +111,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-orangepi-5-plus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-quartzpro64.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-turing-rk1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-coolpi-4b.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-indiedroid-nova.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb

arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts

@@ -143,6 +143,68 @@ &gmac {
 	status = "okay";
 };
 
+&gpio0 {
+	gpio-line-names =
+		/* GPIO0_A0 - A7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO0_B0 - B7 */
+		"", "", "", "header1-pin3 [GPIO0_B3]",
+		"header1-pin5 [GPIO0_B4]", "", "",
+		"header1-pin11 [GPIO0_B7]",
+		/* GPIO0_C0 - C7 */
+		"header1-pin13 [GPIO0_C0]",
+		"header1-pin15 [GPIO0_C1]", "", "", "",
+		"", "", "",
+		/* GPIO0_D0 - D7 */
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio1 {
+	gpio-line-names =
+		/* GPIO1_A0 - A7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO1_B0 - B7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO1_C0 - C7 */
+		"", "", "", "", "", "", "header1-pin21 [GPIO1_C6]",
+		"header1-pin19 [GPIO1_C7]",
+		/* GPIO1_D0 - D7 */
+		"header1-pin23 [GPIO1_D0]", "header1-pin24 [GPIO1_D1]",
+		"", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		/* GPIO2_A0 - A7 */
+		"header1-pin10 [GPIO2_A0]", "header1-pin8 [GPIO2_A1]",
+		"", "",
+		"header1-pin7 [GPIO2_A4]", "header1-pin12 [GPIO2_A5]",
+		"header2-pin46 [GPIO2_A6]", "header1-pin22 [GPIO1_A7]",
+		/* GPIO2_B0 - B7 */
+		"header2-pin45 [GPIO2_B0]", "header1-pin18 [GPIO2_B1]",
+		"header1-pin16 [GPIO2_B2]", "header2-pin44 [GPIO2_B3]",
+		"header2-pin43 [GPIO2_B4]", "header2-pin28 [GPIO2_B5]",
+		"header2-pin30 [GPIO2_B6]", "header2-pin32 [GPIO2_B7]",
+		/* GPIO2_C0 - C7 */
+		"header2-pin34 [GPIO2_C0]", "", "", "", "", "", "", "",
+		/* GPIO2_D0 - D7 */
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		/* GPIO3_A0 - A7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO3_B0 - B7 */
+		"", "", "header2-pin42 [GPIO3_B2]",
+		"header2-pin41 [GPIO3_B3]", "header2-pin40 [GPIO3_B4]",
+		"header2-pin39 [GPIO3_B5]", "", "",
+		/* GPIO3_C0 - C7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO3_D0 - D7 */
+		"", "", "", "", "", "", "", "";
+};
+
 &i2c1 {
 	status = "okay";
 };
@@ -250,61 +312,3 @@ &usb20_otg {
 &wdt {
 	status = "okay";
 };
-
-&gpio0 {
-	gpio-line-names =
-	/* GPIO0_A0 - A7 */
-	"", "", "", "", "", "", "", "",
-	/* GPIO0_B0 - B7 */
-	"", "", "", "header1-pin3 [GPIO0_B3]", "header1-pin5 [GPIO0_B4]",
-	"", "", "header1-pin11 [GPIO0_B7]",
-	/* GPIO0_C0 - C7 */
-	"header1-pin13 [GPIO0_C0]", "header1-pin15 [GPIO0_C1]", "", "", "",
-	"", "", "",
-	/* GPIO0_D0 - D8 */
-	"", "", "", "", "", "", "", "";
-};
-
-&gpio1 {
-	gpio-line-names =
-	/* GPIO1_A0 - A7 */
-	"", "", "", "", "", "", "", "",
-	/* GPIO1_B0 - B7 */
-	"", "", "", "", "", "", "", "",
-	/* GPIO1_C0 - C7 */
-	"", "", "", "", "", "", "header1-pin21 [GPIO1_C6]",
-	"header1-pin19 [GPIO1_C7]",
-	/* GPIO1_D0 - D8 */
-	"header1-pin23 [GPIO1_D0]", "header1-pin24 [GPIO1_D1]", "", "", "",
-	"", "", "";
-};
-
-&gpio2 {
-	gpio-line-names =
-	/* GPIO2_A0 - A7 */
-	"header1-pin10 [GPIO2_A0]", "header1-pin8 [GPIO2_A1]", "", "",
-	"header1-pin7 [GPIO2_A4]", "header1-pin12 [GPIO2_A5]",
-	"header2-pin46 [GPIO2_A6]", "header1-pin22 [GPIO1_A7]",
-	/* GPIO2_B0 - B7 */
-	"header2-pin45 [GPIO2_B0]", "header1-pin18 [GPIO2_B1]",
-	"header1-pin16 [GPIO2_B2]", "header2-pin44 [GPIO2_B3]",
-	"header2-pin43 [GPIO2_B4]", "header2-pin28 [GPIO2_B5]",
-	"header2-pin30 [GPIO2_B6]", "header2-pin32 [GPIO2_B7]",
-	/* GPIO2_C0 - C7 */
-	"header2-pin34 [GPIO2_C0]", "", "", "", "", "", "", "",
-	/* GPIO2_D0 - D8 */
-	"", "", "", "", "", "", "", "";
-};
-
-&gpio3 {
-	gpio-line-names =
-	/* GPIO3_A0 - A7 */
-	"", "", "", "", "", "", "", "",
-	/* GPIO3_B0 - B7 */
-	"", "", "header2-pin42 [GPIO3_B2]", "header2-pin41 [GPIO3_B3]",
-	"header2-pin40 [GPIO3_B4]", "header2-pin39 [GPIO3_B5]", "", "",
-	/* GPIO3_C0 - C7 */
-	"", "", "", "", "", "", "", "",
-	/* GPIO3_D0 - D8 */
-	"", "", "", "", "", "", "", "";
-};

arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts

@@ -26,9 +26,11 @@ yt8531c: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
 
+			motorcomm,auto-sleep-disabled;
 			motorcomm,clk-out-frequency-hz = <125000000>;
 			motorcomm,keep-pll-enabled;
-			motorcomm,auto-sleep-disabled;
+			motorcomm,rx-clk-drv-microamp = <5020>;
+			motorcomm,rx-data-drv-microamp = <5020>;
 
 			pinctrl-0 = <&eth_phy_reset_pin>;
 			pinctrl-names = "default";

arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts

@@ -182,6 +182,59 @@ &gmac2phy {
 	status = "okay";
 };
 
+&gpio0 {
+	gpio-line-names =
+		/* GPIO0_A0 - A7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO0_B0 - B7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO0_C0 - C7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO0_D0 - D7 */
+		"", "", "", "pin-15 [GPIO0_D3]", "", "", "", "";
+};
+
+&gpio1 {
+	gpio-line-names =
+		/* GPIO1_A0 - A7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO1_B0 - B7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO1_C0 - C7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO1_D0 - D7 */
+		"", "", "", "", "pin-07 [GPIO1_D4]", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		/* GPIO2_A0 - A7 */
+		"pin-08 [GPIO2_A0]", "pin-10 [GPIO2_A1]", "pin-11 [GPIO2_A2]",
+		"pin-13 [GPIO2-A3]", "pin-27 [GPIO2_A4]", "pin-28 [GPIO2_A5]",
+		"pin-33 [GPIO2_A6]", "",
+		/* GPIO2_B0 - B7 */
+		"", "", "", "", "pin-26 [GPIO2_B4]", "", "", "pin-36 [GPIO2_B7]",
+		/* GPIO2_C0 - C7 */
+		"pin-32 [GPIO2_C0]", "pin-35 [GPIO2_C1]", "pin-12 [GPIO2_C2]",
+		"pin-38 [GPIO2_C3]", "pin-29 [GPIO2_C4]", "pin-31 [GPIO2_C5]",
+		"pin-37 [GPIO2_C6]", "pin-40 [GPIO2_C7]",
+		/* GPIO2_D0 - D7 */
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		/* GPIO3_A0 - A7 */
+		"pin-23 [GPIO3_A0]", "pin-19 [GPIO3_A1]", "pin-21 [GPIO3_A2]",
+		"", "pin-03 [GPIO3_A4]", "", "pin-05 [GPIO3_A6]", "",
+		/* GPIO3_B0 - B7 */
+		"pin-24 [GPIO3_B0]", "", "", "", "", "", "", "",
+		/* GPIO3_C0 - C7 */
+		"", "", "", "", "", "", "", "",
+		/* GPIO3_D0 - D7 */
+		"", "", "", "", "", "", "", "";
+};
+
 &i2c1 {
 	status = "okay";
 

arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts

@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "rk3399-puma.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Theobroma Systems RK3399-Q7 SoM";
@@ -18,6 +19,38 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&haikou_keys_pin>;
+		pinctrl-names = "default";
+
+		button-batlow-n {
+			gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+			label = "BATLOW#";
+			linux,code = <KEY_BATTERY>;
+		};
+
+		button-slp-btn-n {
+			gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_LOW>;
+			label = "SLP_BTN#";
+			linux,code = <KEY_SLEEP>;
+		};
+
+		button-wake-n {
+			gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_LOW>;
+			label = "WAKE#";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+
+		switch-lid-btn-n {
+			gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+			label = "LID_BTN#";
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+		};
+	};
+
 	leds {
 		pinctrl-0 = <&module_led_pin>, <&sd_card_led_pin>;
 
@@ -165,11 +198,8 @@ &pcie0 {
 };
 
 &pinctrl {
-	pinctrl-names = "default";
-	pinctrl-0 = <&haikou_pin_hog>;
-
-	hog {
-		haikou_pin_hog: haikou-pin-hog {
+	buttons {
+		haikou_keys_pin: haikou-keys-pin {
 			rockchip,pins =
 			  /* LID_BTN */
 			  <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
@@ -177,7 +207,7 @@ haikou_pin_hog: haikou-pin-hog {
 			  <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>,
 			  /* SLP_BTN# */
 			  <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>,
-			  /* BIOS_DISABLE# */
+			  /* WAKE# */
 			  <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};

arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi

@@ -120,6 +120,20 @@ &emmc_phy {
 	drive-impedance-ohm = <33>;
 };
 
+&gpio0 {
+	/*
+	 * The BIOS_DISABLE hog is a feedback pin for the actual status of the
+	 * signal. This usually represents the state of a switch on the baseboard.
+	 * The pin has a 10k pull-up resistor connected, so no pull-up setting is needed.
+	 */
+	bios-disable-hog {
+		gpios = <RK_PB0 GPIO_ACTIVE_HIGH>;
+		gpio-hog;
+		input;
+		line-name = "bios_disable";
+	};
+};
+
 &gmac {
 	assigned-clocks = <&cru SCLK_RMII_SRC>;
 	assigned-clock-parents = <&clkin_gmac>;

arch/arm64/boot/dts/rockchip/rk3566-lubancat-1.dts

@@ -455,7 +455,7 @@ &pcie2x1 {
 &pinctrl {
 	leds {
 		sys_led_pin: sys-status-led-pin {
-			rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
 

arch/arm64/boot/dts/rockchip/rk3588-coolpi-cm5-evb.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2023 Rockchip Electronics Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "rk3588-coolpi-cm5.dtsi"
+
+/ {
+	model = "RK3588 CoolPi CM5 EVB";
+	compatible = "coolpi,pi-cm5-evb", "coolpi,pi-cm5", "rockchip,rk3588";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		enable-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_en>;
+		power-supply = <&vcc12v_dcin>;
+		pwms = <&pwm2 0 25000 0>;
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	vcc12v_dcin: vcc12v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc3v3_lcd: vcc3v3-lcd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_lcd";
+		enable-active-high;
+		gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcdpwr_en>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_host";
+		regulator-boot-on;
+		regulator-always-on;
+		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_host_pwren>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb30_otg: vcc5v0-usb30-otg-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_otg";
+		regulator-boot-on;
+		regulator-always-on;
+		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_otg_pwren>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+/* M.2 E-Key */
+&pcie2x1l1 {
+	reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_sys>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_clkreq &pcie_wake &pcie_rst &wifi_pwron &bt_pwron>;
+	status = "okay";
+};
+
+&pcie30phy {
+	status = "okay";
+};
+
+&pcie3x2 {
+	reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_sys>;
+	status = "okay";
+};
+
+/* M.2 M-Key ssd */
+&pcie3x4 {
+	reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_sys>;
+	status = "okay";
+};
+
+&pinctrl {
+	lcd {
+		lcdpwr_en: lcdpwr-en {
+			rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bl_en: bl-en {
+			rockchip,pins = <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		usb_host_pwren: usb-host-pwren {
+			rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		usb_otg_pwren: usb-otg-pwren {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	wifi {
+		bt_pwron: bt-pwron {
+			rockchip,pins = <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		pcie_clkreq: pcie-clkreq {
+			rockchip,pins = <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		pcie_rst: pcie-rst {
+			rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		wifi_pwron: wifi-pwron {
+			rockchip,pins = <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		pcie_wake: pcie-wake {
+			rockchip,pins = <4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&sata1 {
+	status = "okay";
+};
+
+&u2phy2 {
+	status = "okay";
+};
+
+&u2phy3 {
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};

arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dts

@@ -536,13 +536,12 @@ &sdhci {
 };
 
 &sdmmc {
-	max-frequency = <200000000>;
-	no-sdio;
-	no-mmc;
 	bus-width = <4>;
 	cap-mmc-highspeed;
 	cap-sd-highspeed;
 	disable-wp;
+	no-mmc;
+	no-sdio;
 	sd-uhs-sdr104;
 	vmmc-supply = <&vcc_3v3_s3>;
 	vqmmc-supply = <&vccio_sd_s0>;
@@ -569,6 +568,8 @@ pmic@0 {
 		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
 			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
 
+		system-power-controller;
+
 		vcc1-supply = <&vcc4v0_sys>;
 		vcc2-supply = <&vcc4v0_sys>;
 		vcc3-supply = <&vcc4v0_sys>;
@@ -589,7 +590,7 @@ pmic@0 {
 		#gpio-cells = <2>;
 
 		rk806_dvs1_null: dvs1-null-pins {
-			pins = "gpio_pwrctrl2";
+			pins = "gpio_pwrctrl1";
 			function = "pin_fun0";
 		};
 

arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts

@@ -426,6 +426,8 @@ pmic@0 {
 		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
 			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
 
+		system-power-controller;
+
 		vcc1-supply = <&vcc5v0_sys>;
 		vcc2-supply = <&vcc5v0_sys>;
 		vcc3-supply = <&vcc5v0_sys>;
@@ -446,7 +448,7 @@ pmic@0 {
 		#gpio-cells = <2>;
 
 		rk806_dvs1_null: dvs1-null-pins {
-			pins = "gpio_pwrctrl2";
+			pins = "gpio_pwrctrl1";
 			function = "pin_fun0";
 		};
 

arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts

@@ -314,6 +314,7 @@ pmic@0 {
 		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
 				<&rk806_dvs2_null>, <&rk806_dvs3_null>;
 		spi-max-frequency = <1000000>;
+		system-power-controller;
 
 		vcc1-supply = <&vcc5v0_sys>;
 		vcc2-supply = <&vcc5v0_sys>;

arch/arm64/boot/dts/rockchip/rk3588s.dtsi

@@ -394,6 +394,11 @@ spll: clock-0 {
 		#clock-cells = <0>;
 	};
 
+	display_subsystem: display-subsystem {
+		compatible = "rockchip,display-subsystem";
+		ports = <&vop_out>;
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
@@ -506,6 +511,16 @@ sys_grf: syscon@fd58c000 {
 		reg = <0x0 0xfd58c000 0x0 0x1000>;
 	};
 
+	vop_grf: syscon@fd5a4000 {
+		compatible = "rockchip,rk3588-vop-grf", "syscon";
+		reg = <0x0 0xfd5a4000 0x0 0x2000>;
+	};
+
+	vo1_grf: syscon@fd5a8000 {
+		compatible = "rockchip,rk3588-vo-grf", "syscon";
+		reg = <0x0 0xfd5a8000 0x0 0x100>;
+	};
+
 	php_grf: syscon@fd5b0000 {
 		compatible = "rockchip,rk3588-php-grf", "syscon";
 		reg = <0x0 0xfd5b0000 0x0 0x1000>;
@@ -625,6 +640,74 @@ i2c0: i2c@fd880000 {
 		status = "disabled";
 	};
 
+	vop: vop@fdd90000 {
+		compatible = "rockchip,rk3588-vop";
+		reg = <0x0 0xfdd90000 0x0 0x4200>, <0x0 0xfdd95000 0x0 0x1000>;
+		reg-names = "vop", "gamma-lut";
+		interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru ACLK_VOP>,
+			 <&cru HCLK_VOP>,
+			 <&cru DCLK_VOP0>,
+			 <&cru DCLK_VOP1>,
+			 <&cru DCLK_VOP2>,
+			 <&cru DCLK_VOP3>,
+			 <&cru PCLK_VOP_ROOT>;
+		clock-names = "aclk",
+			      "hclk",
+			      "dclk_vp0",
+			      "dclk_vp1",
+			      "dclk_vp2",
+			      "dclk_vp3",
+			      "pclk_vop";
+		iommus = <&vop_mmu>;
+		power-domains = <&power RK3588_PD_VOP>;
+		rockchip,grf = <&sys_grf>;
+		rockchip,vop-grf = <&vop_grf>;
+		rockchip,vo1-grf = <&vo1_grf>;
+		rockchip,pmu = <&pmu>;
+		status = "disabled";
+
+		vop_out: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vp0: port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+			};
+
+			vp1: port@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+			};
+
+			vp2: port@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;
+			};
+
+			vp3: port@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+			};
+		};
+	};
+
+	vop_mmu: iommu@fdd97e00 {
+		compatible = "rockchip,rk3588-iommu", "rockchip,rk3568-iommu";
+		reg = <0x0 0xfdd97e00 0x0 0x100>, <0x0 0xfdd97f00 0x0 0x100>;
+		interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
+		clock-names = "aclk", "iface";
+		#iommu-cells = <0>;
+		power-domains = <&power RK3588_PD_VOP>;
+		status = "disabled";
+	};
+
 	uart0: serial@fd890000 {
 		compatible = "rockchip,rk3588-uart", "snps,dw-apb-uart";
 		reg = <0x0 0xfd890000 0x0 0x100>;
@@ -948,6 +1031,7 @@ power-domain@RK3588_PD_USB {
 				reg = <RK3588_PD_USB>;
 				clocks = <&cru PCLK_PHP_ROOT>,
 					 <&cru ACLK_USB_ROOT>,
+					 <&cru ACLK_USB>,
 					 <&cru HCLK_USB_ROOT>,
 					 <&cru HCLK_HOST0>,
 					 <&cru HCLK_HOST_ARB0>,