Merge tag 'qcom-arm64-for-5.1' of...

Merge tag 'qcom-arm64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/dt

Qualcomm ARM64 Updates for v5.1

* Add MSM8998 RPMCC, I2C, and USB related nodes
* Add MSM8996 rpmpd node
* Fix typo in MSM8996 pin definitions
* Disable MSM8996 VFE smmu to fix security violation
* Add I2C, SPI, rpmcc, uart, and WCN3990 wlan nodes on QCS404
* Enable SDCC1 HS400 support on QCS404
* Add a multitude of nodes on SDM845:
  SD, UFS, USB, LPASS, SCM, QSPI, PDC, DPU, videocc, GPU, RPMh
  bus interconnect, WCN3990 WLAN
* Add gpio ranges to SDM845 TLMM
* Fix regulator load on sdcard on MSM8998-mtp board

* tag 'qcom-arm64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (41 commits)
  arm64: dts: sdm845: Add interconnect provider DT nodes
  arm64: dts: qcom: msm8996: Disabled VFE SMMU
  arm64: dts: qcom: qcs404: Add rpmcc node
  arm64: dts: qcom: msm8998: Add rpmcc node
  arm64: dts: qcom: msm8998: Add USB-related nodes
  arm64: dts: qcom: qcs404: Add QUP I2C and SPI nodes
  arm64: dts: qcom: qcs404: Define remaining UARTs
  arm64: dts: qcom: qcs404: Specify pinctrl state for UART
  arm64: dts: qcom: sdm845: Fix lpasscc reg
  arm64: dts: qcom: sdm845: Remove the duplicate header inclusion
  arm64: dts: qcom: sdm845: Add reserve-memory nodes
  arm64: dts: qcom: sdm845: Add gpio-ranges to TLMM node
  arm64: dts: qcom: sdm845: Extend ranges and describe DMA space
  arm64: dts: qcom: sdm845: Increase address and size cells for soc
  arm64: dts: sdm845: Add rpmh powercontroller node
  arm64: dts: msm8996: Add rpmpd device node
  arm64: dts: sdm845: Add WCN3990 WLAN module device node
  arm64: dts: qcom: sdm845: Add PDC Global reset driver node
  arm64: dts: qcom: sdm845: Add SCM DT node
  arm64: dts: qcom: sdm845: Fix pcs_misc region address for UNI PHY
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi

@@ -644,6 +644,8 @@ l10 {
 	l11 {
 		regulator-min-microvolt = <1750000>;
 		regulator-max-microvolt = <3337000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
 	};
 
 	l12 {

arch/arm64/boot/dts/qcom/msm8996-pins.dtsi

@@ -139,7 +139,7 @@ pinmux {
 		};
 
 		pinconf {
-			pins = "gpio4", "gpiio5", "gpio6", "gpio7";
+			pins = "gpio4", "gpio5", "gpio6", "gpio7";
 			drive-strength = <2>;
 			bias-disable;
 		};

arch/arm64/boot/dts/qcom/msm8996.dtsi

@@ -306,6 +306,40 @@ rpmcc: qcom,rpmcc {
 				#clock-cells = <1>;
 			};
 
+			rpmpd: power-controller {
+				compatible = "qcom,msm8996-rpmpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmpd_opp_table>;
+
+				rpmpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmpd_opp1: opp1 {
+						opp-level = <1>;
+					};
+
+					rpmpd_opp2: opp2 {
+						opp-level = <2>;
+					};
+
+					rpmpd_opp3: opp3 {
+						opp-level = <3>;
+					};
+
+					rpmpd_opp4: opp4 {
+						opp-level = <4>;
+					};
+
+					rpmpd_opp5: opp5 {
+						opp-level = <5>;
+					};
+
+					rpmpd_opp6: opp6 {
+						opp-level = <6>;
+					};
+				};
+			};
+
 			pm8994-regulators {
 				compatible = "qcom,rpm-pm8994-regulators";
 
@@ -404,7 +438,7 @@ tcsr: syscon@7a0000 {
 		};
 
 		intc: interrupt-controller@9bc0000 {
-			compatible = "arm,gic-v3";
+			compatible = "qcom,msm8996-gic-v3", "arm,gic-v3";
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			#redistributor-regions = <1>;
@@ -966,7 +1000,7 @@ vfe_smmu: arm,smmu@da0000 {
 			clock-names = "iface",
 				      "bus";
 			#iommu-cells = <1>;
-			status = "ok";
+			status = "disabled";
 		};
 
 		camss: camss@a00000 {

arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi

@@ -65,6 +65,13 @@ &blsp2_uart1 {
 	status = "okay";
 };
 
+&qusb2phy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
 &rpm_requests {
 	pm8998-regulators {
 		compatible = "qcom,rpm-pm8998-regulators";
@@ -192,6 +199,8 @@ vreg_l20a_2p95: l20 {
 		vreg_l21a_2p95: l21 {
 			regulator-min-microvolt = <2960000>;
 			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+			regulator-system-load = <800000>;
 		};
 		vreg_l22a_2p85: l22 {
 			regulator-min-microvolt = <2864000>;
@@ -257,3 +266,18 @@ &sdhc2 {
 	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on  &sdc2_data_on  &sdc2_cd_on>;
 	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
 };
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "host"; /* Force to host until we have Type-C hooked up */
+};
+
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+};

arch/arm64/boot/dts/qcom/msm8998.dtsi

@@ -3,6 +3,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8998.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
 #include <dt-bindings/gpio/gpio.h>
 
 / {
@@ -266,6 +267,11 @@ rpm-glink {
 		rpm_requests: rpm-requests {
 			compatible = "qcom,rpm-msm8998";
 			qcom,glink-channels = "rpm_requests";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-msm8998", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
 		};
 	};
 
@@ -540,6 +546,11 @@ qfprom: qfprom@780000 {
 			reg = <0x780000 0x621c>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+
+			qusb2_hstx_trim: hstx-trim@423a {
+				reg = <0x423a 0x1>;
+				bits = <0 4>;
+			};
 		};
 
 		gcc: clock-controller@100000 {
@@ -607,6 +618,93 @@ apcs_glb: mailbox@9820000 {
 			#mbox-cells = <1>;
 		};
 
+		usb3: usb@a8f8800 {
+			compatible = "qcom,msm8998-dwc3", "qcom,dwc3";
+			reg = <0x0a8f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_AXI_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_AGGRE1_USB3_AXI_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <120000000>;
+
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq";
+
+			power-domains = <&gcc USB_30_GDSC>;
+
+			resets = <&gcc GCC_USB_30_BCR>;
+
+			usb3_dwc3: dwc3@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0x0a800000 0xcd00>;
+				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&qusb2phy>, <&usb1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				snps,has-lpm-erratum;
+				snps,hird-threshold = /bits/ 8 <0x10>;
+			};
+		};
+
+		usb3phy: phy@c010000 {
+			compatible = "qcom,msm8998-qmp-usb3-phy";
+			reg = <0x0c010000 0x18c>;
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_CLKREF_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_USB3_PHY_BCR>,
+				 <&gcc GCC_USB3PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			usb1_ssphy: lane@c010200 {
+				reg = <0xc010200 0x128>,
+				      <0xc010400 0x200>,
+				      <0xc010c00 0x20c>,
+				      <0xc010600 0x128>,
+				      <0xc010800 0x200>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
+		qusb2phy: phy@c012000 {
+			compatible = "qcom,msm8998-qusb2-phy";
+			reg = <0x0c012000 0x2a8>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_RX1_USB2_CLKREF_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			nvmem-cells = <&qusb2_hstx_trim>;
+		};
+
 		sdhc2: sdhci@c0a4900 {
 			compatible = "qcom,sdhci-msm-v4";
 			reg = <0xc0a4900 0x314>, <0xc0a4000 0x800>;
@@ -624,6 +722,186 @@ sdhc2: sdhci@c0a4900 {
 			status = "disabled";
 		};
 
+		blsp1_i2c1: i2c@c175000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c175000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@c176000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c176000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@c177000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c177000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c4: i2c@c178000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c178000 0x600>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c5: i2c@c179000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c179000 0x600>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c6: i2c@c17a000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c17a000 0x600>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c0: i2c@c1b5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b5000 0x600>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c1: i2c@c1b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b6000 0x600>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c2: i2c@c1b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b7000 0x600>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c3: i2c@c1b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b8000 0x600>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c4: i2c@c1b9000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b9000 0x600>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c5: i2c@c1ba000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c175000 0x600>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		blsp2_uart1: serial@c1b0000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0xc1b0000 0x1000>;

arch/arm64/boot/dts/qcom/pm8916.dtsi

@@ -32,6 +32,12 @@ pwrkey {
 				bias-pull-up;
 				linux,code = <KEY_POWER>;
 			};
+
+			watchdog {
+				compatible = "qcom,pm8916-wdt";
+				interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>;
+				timeout-sec = <60>;
+			};
 		};
 
 		pm8916_gpios: gpios@c000 {

arch/arm64/boot/dts/qcom/pms405.dtsi

@@ -3,6 +3,32 @@
 
 #include <dt-bindings/spmi/spmi.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	thermal-zones {
+		pms405 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&pms405_temp>;
+
+			trips {
+				pms405_alert0: pms405-alert0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				pms405_crit: pms405-crit {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
 
 &spmi_bus {
 	pms405_0: pms405@0 {
@@ -45,6 +71,59 @@ pwrkey {
 			};
 		};
 
+		pms405_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pms405_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pms405_adc: adc@3100 {
+			compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			ref_gnd {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			vref_1p25 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			vph_pwr {
+				reg = <ADC5_VPH_PWR>;
+				qcom,pre-scaling = <1 3>;
+			};
+
+			die_temp {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			xo_therm_100k_pu {
+				reg = <ADC5_XO_THERM_100K_PU>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			amux_thm1_100k_pu {
+				reg = <ADC5_AMUX_THM1_100K_PU>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			amux_thm3_100k_pu {
+				reg = <ADC5_AMUX_THM3_100K_PU>;
+				qcom,pre-scaling = <1 1>;
+			};
+		};
+
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>;

arch/arm64/boot/dts/qcom/qcs404-evb.dtsi

@@ -127,6 +127,7 @@ &sdcc1 {
 	status = "ok";
 
 	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
 	bus-width = <8>;
 	non-removable;
 
@@ -186,3 +187,21 @@ rclk {
 		};
 	};
 };
+
+&wifi {
+	status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in qcs404.dtsi */
+
+&blsp1_uart2_default {
+	rx {
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tx {
+		drive-strength = <2>;
+		bias-disable;
+	};
+};

arch/arm64/boot/dts/qcom/sdm845-mtp.dts

@@ -7,6 +7,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sdm845.dtsi"
 
@@ -346,7 +347,9 @@ vreg_s3c_0p6: smps3 {
 &gcc {
 	protected-clocks = <GCC_QSPI_CORE_CLK>,
 			   <GCC_QSPI_CORE_CLK_SRC>,
-			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
 };
 
 &i2c10 {
@@ -358,14 +361,36 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
-&tlmm {
-	gpio-reserved-ranges = <0 4>, <81 4>;
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vddpx_2>;
+
+	cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
 };
 
 &uart9 {
 	status = "okay";
 };
 
+&ufs_mem_hc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
 &usb_1 {
 	status = "okay";
 };
@@ -427,6 +452,14 @@ &usb_2_qmpphy {
 	vdda-pll-supply = <&vdda_usb2_ss_core>;
 };
 
+&wifi {
+	status = "okay";
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
+
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 
 &qup_i2c10_default {
@@ -450,3 +483,48 @@ pinconf-rx {
 		bias-pull-up;
 	};
 };
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	sdc2_clk: sdc2-clk {
+		pinconf {
+			pins = "sdc2_clk";
+			bias-disable;
+
+			/*
+			 * It seems that mmc_test reports errors if drive
+			 * strength is not 16 on clk, cmd, and data pins.
+			 */
+			drive-strength = <16>;
+		};
+	};
+
+	sdc2_cmd: sdc2-cmd {
+		pinconf {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+
+	sdc2_data: sdc2-data {
+		pinconf {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+
+	sd_card_det_n: sd-card-det-n {
+		pinmux {
+			pins = "gpio126";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio126";
+			bias-pull-up;
+		};
+	};
+};