Skip to content

L
linux
Commit 2b0460b5 authored by Linus Torvalds's avatar Linus Torvalds
Browse files
Options

Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6 

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6: (33 commits)
  amd74xx: remove /proc/ide/amd74xx
  amd74xx/via82cxxx: don't initialize drive->dn
  sis5513: remove /proc/ide/sis
  ide: remove CONFIG_IDEDMA_ONLYDISK
  ide: add "hdx=nodma" kernel parameter
  ide: remove hwif->autodma and drive->autodma
  ide: remove "idex=dma" kernel parameter
  ide: remove CONFIG_BLK_DEV_IDEDMA_FORCED
  ide: use PCI_VDEVICE() macro
  sis5513: clear prefetch and postwrite for ATAPI devices
  it8213/piix/slc90e66: "de-couple" PIO and UDMA modes
  ide: unexport noautodma
  ide: unexport ide_tune_dma
  ide: remove ->ide_dma_check (take 2)
  ide-pmac: add PIO autotune fallback to ->ide_dma_check
  ide-cris: add PIO autotune fallback to ->ide_dma_check
  sl82c105: add PIO autotune fallback to ->ide_dma_check
  cs5530/sc1200: add PIO autotune fallback to ->ide_dma_check
  ide: remove ide_use_fast_pio()
  ide: remove drive->init_speed zeroing
  ...
parents d91f5bb6 b02fcae0
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 449 additions and 1699 deletions
Documentation/ide.txt
View file @ 2b0460b5
......@@ -242,6 +242,8 @@ Summary of ide driver parameters for kernel command line
and quite likely to cause trouble with
older/odd IDE drives.
"hdx=nodma" : disallow DMA
"hdx=swapdata" : when the drive is a disk, byte swap all data
"hdx=bswap" : same as above..........
......@@ -278,8 +280,6 @@ Summary of ide driver parameters for kernel command line
"idex=four" : four drives on idex and ide(x^1) share same ports
"idex=reset" : reset interface after probe
"idex=dma" : automatically configure/use DMA if possible.
"idex=ata66" : informs the interface that it has an 80c cable
for chipsets that are ATA-66 capable, but the
......@@ -288,8 +288,6 @@ Summary of ide driver parameters for kernel command line
"ide=reverse" : formerly called to pci sub-system, but now local.
"ide=nodma" : disable DMA globally for the IDE subsystem.
The following are valid ONLY on ide0, which usually corresponds
to the first ATA interface found on the particular host, and the defaults for
the base,ctl ports must not be altered.
......
drivers/ide/Kconfig
View file @ 2b0460b5
......@@ -435,24 +435,6 @@ config BLK_DEV_IDEDMA_PCI
bool
select BLK_DEV_IDEPCI
config BLK_DEV_IDEDMA_FORCED
bool "Force enable legacy 2.0.X HOSTS to use DMA"
depends on BLK_DEV_IDEDMA_PCI
help
This is an old piece of lost code from Linux 2.0 Kernels.
Generally say N here.
# TODO: remove it
config IDEDMA_ONLYDISK
bool "Enable DMA only for disks "
depends on BLK_DEV_IDEDMA_PCI
help
This is used if you know your ATAPI Devices are going to fail DMA
Transfers.
Generally say N here.
config BLK_DEV_AEC62XX
tristate "AEC62XX chipset support"
select BLK_DEV_IDEDMA_PCI
......
drivers/ide/arm/icside.c
View file @ 2b0460b5
......@@ -309,14 +309,6 @@ static int icside_dma_on(ide_drive_t *drive)
return 0;
}
static int icside_dma_check(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
return -1;
}
static int icside_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
......@@ -423,8 +415,6 @@ static void icside_dma_lost_irq(ide_drive_t *drive)
static void icside_dma_init(ide_hwif_t *hwif)
{
printk(" %s: SG-DMA", hwif->name);
hwif->atapi_dma = 1;
hwif->mwdma_mask = 7; /* MW0..2 */
hwif->swdma_mask = 7; /* SW0..2 */
......@@ -432,9 +422,7 @@ static void icside_dma_init(ide_hwif_t *hwif)
hwif->dmatable_cpu = NULL;
hwif->dmatable_dma = 0;
hwif->set_dma_mode = icside_set_dma_mode;
hwif->autodma = 1;
hwif->ide_dma_check = icside_dma_check;
hwif->dma_host_off = icside_dma_host_off;
hwif->dma_off_quietly = icside_dma_off_quietly;
hwif->dma_host_on = icside_dma_host_on;
......@@ -446,11 +434,6 @@ static void icside_dma_init(ide_hwif_t *hwif)
hwif->ide_dma_test_irq = icside_dma_test_irq;
hwif->dma_timeout = icside_dma_timeout;
hwif->dma_lost_irq = icside_dma_lost_irq;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
printk(" capable%s\n", hwif->autodma ? ", auto-enable" : "");
}
#else
#define icside_dma_init(hwif) (0)
......
drivers/ide/cris/ide-cris.c
View file @ 2b0460b5
......@@ -664,7 +664,6 @@ cris_ide_inb(unsigned long reg)
return (unsigned char)cris_ide_inw(reg);
}
static int cris_dma_check (ide_drive_t *drive);
static int cris_dma_end (ide_drive_t *drive);
static int cris_dma_setup (ide_drive_t *drive);
static void cris_dma_exec_cmd (ide_drive_t *drive, u8 command);
......@@ -792,7 +791,6 @@ init_e100_ide (void)
hwif->ata_output_data = &cris_ide_output_data;
hwif->atapi_input_bytes = &cris_atapi_input_bytes;
hwif->atapi_output_bytes = &cris_atapi_output_bytes;
hwif->ide_dma_check = &cris_dma_check;
hwif->ide_dma_end = &cris_dma_end;
hwif->dma_setup = &cris_dma_setup;
hwif->dma_exec_cmd = &cris_dma_exec_cmd;
......@@ -808,11 +806,10 @@ init_e100_ide (void)
hwif->dma_off_quietly = &cris_dma_off;
hwif->cbl = ATA_CBL_PATA40;
hwif->pio_mask = ATA_PIO4,
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
hwif->ultra_mask = cris_ultra_mask;
hwif->mwdma_mask = 0x07; /* Multiword DMA 0-2 */
hwif->autodma = 1;
hwif->drives[0].autodma = 1;
hwif->drives[1].autodma = 1;
}
/* Reset pulse */
......@@ -1018,14 +1015,6 @@ static ide_startstop_t cris_dma_intr (ide_drive_t *drive)
* the caller should revert to PIO for the current request.
*/
static int cris_dma_check(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
return -1;
}
static int cris_dma_end(ide_drive_t *drive)
{
drive->waiting_for_dma = 0;
......
drivers/ide/ide-dma.c
View file @ 2b0460b5
......@@ -338,35 +338,30 @@ static int config_drive_for_dma (ide_drive_t *drive)
ide_hwif_t *hwif = drive->hwif;
struct hd_driveid *id = drive->id;
/* consult the list of known "bad" drives */
if (__ide_dma_bad_drive(drive))
return -1;
if (drive->media != ide_disk && hwif->atapi_dma == 0)
return -1;
return 0;
if ((id->capability & 1) && drive->autodma) {
/*
* Enable DMA on any drive that has
* UltraDMA (mode 0/1/2/3/4/5/6) enabled
*/
if ((id->field_valid & 4) && ((id->dma_ultra >> 8) & 0x7f))
return 0;
/*
* Enable DMA on any drive that has mode2 DMA
* (multi or single) enabled
*/
if (id->field_valid & 2) /* regular DMA */
if ((id->dma_mword & 0x404) == 0x404 ||
(id->dma_1word & 0x404) == 0x404)
return 0;
/* Consult the list of known "good" drives */
if (ide_dma_good_drive(drive))
return 0;
}
/*
* Enable DMA on any drive that has
* UltraDMA (mode 0/1/2/3/4/5/6) enabled
*/
if ((id->field_valid & 4) && ((id->dma_ultra >> 8) & 0x7f))
return 1;
/*
* Enable DMA on any drive that has mode2 DMA
* (multi or single) enabled
*/
if (id->field_valid & 2) /* regular DMA */
if ((id->dma_mword & 0x404) == 0x404 ||
(id->dma_1word & 0x404) == 0x404)
return 1;
/* Consult the list of known "good" drives */
if (ide_dma_good_drive(drive))
return 1;
return -1;
return 0;
}
/**
......@@ -627,6 +622,8 @@ static int __ide_dma_test_irq(ide_drive_t *drive)
drive->name, __FUNCTION__);
return 0;
}
#else
static inline int config_drive_for_dma(ide_drive_t *drive) { return 0; }
#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
int __ide_dma_bad_drive (ide_drive_t *drive)
......@@ -758,17 +755,20 @@ u8 ide_find_dma_mode(ide_drive_t *drive, u8 req_mode)
EXPORT_SYMBOL_GPL(ide_find_dma_mode);
int ide_tune_dma(ide_drive_t *drive)
static int ide_tune_dma(ide_drive_t *drive)
{
u8 speed;
if ((drive->id->capability & 1) == 0 || drive->autodma == 0)
if (noautodma || drive->nodma || (drive->id->capability & 1) == 0)
return 0;
/* consult the list of known "bad" drives */
if (__ide_dma_bad_drive(drive))
return 0;
if (drive->hwif->host_flags & IDE_HFLAG_TRUST_BIOS_FOR_DMA)
return config_drive_for_dma(drive);
speed = ide_max_dma_mode(drive);
if (!speed)
......@@ -783,7 +783,22 @@ int ide_tune_dma(ide_drive_t *drive)
return 1;
}
EXPORT_SYMBOL_GPL(ide_tune_dma);
static int ide_dma_check(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
int vdma = (hwif->host_flags & IDE_HFLAG_VDMA)? 1 : 0;
if (!vdma && ide_tune_dma(drive))
return 0;
/* TODO: always do PIO fallback */
if (hwif->host_flags & IDE_HFLAG_TRUST_BIOS_FOR_DMA)
return -1;
ide_set_max_pio(drive);
return vdma ? 0 : -1;
}
void ide_dma_verbose(ide_drive_t *drive)
{
......@@ -842,7 +857,7 @@ int ide_set_dma(ide_drive_t *drive)
ide_hwif_t *hwif = drive->hwif;
int rc;
rc = hwif->ide_dma_check(drive);
rc = ide_dma_check(drive);
switch(rc) {
case -1: /* DMA needs to be disabled */
......@@ -1019,8 +1034,6 @@ void ide_setup_dma (ide_hwif_t *hwif, unsigned long dma_base, unsigned int num_p
hwif->ide_dma_on = &__ide_dma_on;
if (!hwif->dma_host_on)
hwif->dma_host_on = &ide_dma_host_on;
if (!hwif->ide_dma_check)
hwif->ide_dma_check = &config_drive_for_dma;
if (!hwif->dma_setup)
hwif->dma_setup = &ide_dma_setup;
if (!hwif->dma_exec_cmd)
......
drivers/ide/ide-io.c
View file @ 2b0460b5
......@@ -219,11 +219,11 @@ static ide_startstop_t ide_start_power_step(ide_drive_t *drive, struct request *
case ide_pm_restore_dma: /* Resume step 3 (restore DMA) */
/*
* Right now, all we do is call hwif->ide_dma_check(drive),
* Right now, all we do is call ide_set_dma(drive),
* we could be smarter and check for current xfer_speed
* in struct drive etc...
*/
if (drive->hwif->ide_dma_check == NULL)
if (drive->hwif->ide_dma_on == NULL)
break;
drive->hwif->dma_off_quietly(drive);
/*
......
drivers/ide/ide-iops.c
View file @ 2b0460b5
......@@ -776,7 +776,7 @@ int ide_config_drive_speed(ide_drive_t *drive, u8 speed)
// msleep(50);
#ifdef CONFIG_BLK_DEV_IDEDMA
if (hwif->ide_dma_check) /* check if host supports DMA */
if (hwif->ide_dma_on) /* check if host supports DMA */
hwif->dma_host_off(drive);
#endif
......@@ -830,7 +830,7 @@ int ide_config_drive_speed(ide_drive_t *drive, u8 speed)
#ifdef CONFIG_BLK_DEV_IDEDMA
if (speed >= XFER_SW_DMA_0)
hwif->dma_host_on(drive);
else if (hwif->ide_dma_check) /* check if host supports DMA */
else if (hwif->ide_dma_on) /* check if host supports DMA */
hwif->dma_off_quietly(drive);
#endif
......
drivers/ide/ide-lib.c
View file @ 2b0460b5
......@@ -96,21 +96,6 @@ static u8 ide_rate_filter(ide_drive_t *drive, u8 speed)
return min(speed, mode);
}
int ide_use_fast_pio(ide_drive_t *drive)
{
struct hd_driveid *id = drive->id;
if ((id->capability & 1) && drive->autodma)
return 1;
if ((id->capability & 8) || (id->field_valid & 2))
return 1;
return 0;
}
EXPORT_SYMBOL_GPL(ide_use_fast_pio);
/*
* Standard (generic) timings for PIO modes, from ATA2 specification.
* These timings are for access to the IDE data port register *only*.
......
drivers/ide/ide-probe.c
View file @ 2b0460b5
......@@ -835,16 +835,7 @@ static void probe_hwif(ide_hwif_t *hwif, void (*fixup)(ide_hwif_t *hwif))
drive->nice1 = 1;
/*
* MAJOR HACK BARF :-/
*
* FIXME: chipsets own this cruft!
*/
/*
* Move here to prevent module loading clashing.
*/
// drive->autodma = hwif->autodma;
if (hwif->ide_dma_check) {
if (hwif->ide_dma_on) {
/*
* Force DMAing for the beginning of the check.
* Some chipsets appear to do interesting
......@@ -852,10 +843,7 @@ static void probe_hwif(ide_hwif_t *hwif, void (*fixup)(ide_hwif_t *hwif))
* PARANOIA!!!
*/
hwif->dma_off_quietly(drive);
#ifdef CONFIG_IDEDMA_ONLYDISK
if (drive->media == ide_disk)
#endif
ide_set_dma(drive);
ide_set_dma(drive);
}
}
}
......
drivers/ide/ide.c
View file @ 2b0460b5
......@@ -100,8 +100,6 @@ static int ide_scan_direction; /* THIS was formerly 2.2.x pci=reverse */
int noautodma = 0;
EXPORT_SYMBOL(noautodma);
#ifdef CONFIG_BLK_DEV_IDEACPI
int ide_noacpi = 0;
int ide_noacpitfs = 1;
......@@ -418,7 +416,6 @@ static void ide_hwif_restore(ide_hwif_t *hwif, ide_hwif_t *tmp_hwif)
hwif->dma_exec_cmd = tmp_hwif->dma_exec_cmd;
hwif->dma_start = tmp_hwif->dma_start;
hwif->ide_dma_end = tmp_hwif->ide_dma_end;
hwif->ide_dma_check = tmp_hwif->ide_dma_check;
hwif->ide_dma_on = tmp_hwif->ide_dma_on;
hwif->dma_off_quietly = tmp_hwif->dma_off_quietly;
hwif->ide_dma_test_irq = tmp_hwif->ide_dma_test_irq;
......@@ -461,7 +458,6 @@ static void ide_hwif_restore(ide_hwif_t *hwif, ide_hwif_t *tmp_hwif)
hwif->select_data = tmp_hwif->select_data;
hwif->extra_base = tmp_hwif->extra_base;
hwif->extra_ports = tmp_hwif->extra_ports;
hwif->autodma = tmp_hwif->autodma;
hwif->hwif_data = tmp_hwif->hwif_data;
}
......@@ -823,7 +819,7 @@ int set_using_dma(ide_drive_t *drive, int arg)
if (!drive->id || !(drive->id->capability & 1))
goto out;
if (hwif->ide_dma_check == NULL)
if (hwif->ide_dma_on == NULL)
goto out;
err = -EBUSY;
......@@ -1276,7 +1272,7 @@ static int __init ide_setup(char *s)
if (!strcmp(s, "ide=nodma")) {
printk(" : Prevented DMA\n");
noautodma = 1;
return 1;
goto obsolete_option;
}
#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
......@@ -1310,7 +1306,7 @@ static int __init ide_setup(char *s)
*/
if (s[0] == 'h' && s[1] == 'd' && s[2] >= 'a' && s[2] <= max_drive) {
const char *hd_words[] = {
"none", "noprobe", "nowerr", "cdrom", "minus5",
"none", "noprobe", "nowerr", "cdrom", "nodma",
"autotune", "noautotune", "minus8", "swapdata", "bswap",
"noflush", "remap", "remap63", "scsi", NULL };
unit = s[2] - 'a';
......@@ -1338,6 +1334,9 @@ static int __init ide_setup(char *s)
drive->ready_stat = 0;
hwif->noprobe = 0;
goto done;
case -5: /* nodma */
drive->nodma = 1;
goto done;
case -6: /* "autotune" */
drive->autotune = IDE_TUNE_AUTO;
goto obsolete_option;
......@@ -1399,7 +1398,7 @@ static int __init ide_setup(char *s)
*/
static const char *ide_words[] = {
"noprobe", "serialize", "minus3", "minus4",
"reset", "dma", "ata66", "minus8", "minus9",
"reset", "minus6", "ata66", "minus8", "minus9",
"minus10", "four", "qd65xx", "ht6560b", "cmd640_vlb",
"dtc2278", "umc8672", "ali14xx", NULL };
hw = s[3] - '0';
......@@ -1478,6 +1477,7 @@ static int __init ide_setup(char *s)
case -10: /* minus10 */
case -9: /* minus9 */
case -8: /* minus8 */
case -6:
case -4:
case -3:
goto bad_option;
......@@ -1492,9 +1492,6 @@ static int __init ide_setup(char *s)
#else
goto bad_hwif;
#endif
case -6: /* dma */
hwif->autodma = 1;
goto obsolete_option;
case -5: /* "reset" */
hwif->reset = 1;
goto obsolete_option;
......
drivers/ide/legacy/ide-cs.c
View file @ 2b0460b5
......@@ -28,7 +28,7 @@
and other provisions required by the GPL. If you do not delete
the provisions above, a recipient may use your version of this
file under either the MPL or the GPL.
======================================================================*/
#include <linux/module.h>
......@@ -327,13 +327,13 @@ static int ide_config(struct pcmcia_device *link)
After a card is removed, ide_release() will unregister the net
device, and release the PCMCIA configuration. If the device is
still open, this will be postponed until it is closed.
======================================================================*/
void ide_release(struct pcmcia_device *link)
{
ide_info_t *info = link->priv;
DEBUG(0, "ide_release(0x%p)\n", link);
if (info->ndev) {
......@@ -353,11 +353,12 @@ void ide_release(struct pcmcia_device *link)
stuff to run after an event is received. A CARD_REMOVAL event
also sets some flags to discourage the ide drivers from
talking to the ports.
======================================================================*/
static struct pcmcia_device_id ide_ids[] = {
PCMCIA_DEVICE_FUNC_ID(4),
PCMCIA_DEVICE_MANF_CARD(0x0000, 0x0000), /* Corsair */
PCMCIA_DEVICE_MANF_CARD(0x0007, 0x0000), /* Hitachi */
PCMCIA_DEVICE_MANF_CARD(0x000a, 0x0000), /* I-O Data CFA */
PCMCIA_DEVICE_MANF_CARD(0x001c, 0x0001), /* Mitsubishi CFA */
......@@ -366,7 +367,7 @@ static struct pcmcia_device_id ide_ids[] = {
PCMCIA_DEVICE_MANF_CARD(0x0098, 0x0000), /* Toshiba */
PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x002d),
PCMCIA_DEVICE_MANF_CARD(0x00ce, 0x0000), /* Samsung */
PCMCIA_DEVICE_MANF_CARD(0x0319, 0x0000), /* Hitachi */
PCMCIA_DEVICE_MANF_CARD(0x0319, 0x0000), /* Hitachi */
PCMCIA_DEVICE_MANF_CARD(0x2080, 0x0001),
PCMCIA_DEVICE_MANF_CARD(0x4e01, 0x0100), /* Viking CFA */
PCMCIA_DEVICE_MANF_CARD(0x4e01, 0x0200), /* Lexar, Viking CFA */
......@@ -384,6 +385,7 @@ static struct pcmcia_device_id ide_ids[] = {
PCMCIA_DEVICE_PROD_ID12("FREECOM", "PCCARD-IDE", 0x5714cbf7, 0x48e0ab8e),
PCMCIA_DEVICE_PROD_ID12("HITACHI", "FLASH", 0xf4f43949, 0x9eb86aae),
PCMCIA_DEVICE_PROD_ID12("HITACHI", "microdrive", 0xf4f43949, 0xa6d76178),
PCMCIA_DEVICE_PROD_ID12("Hyperstone", "Model1", 0x3d5b9ef5, 0xca6ab420),
PCMCIA_DEVICE_PROD_ID12("IBM", "microdrive", 0xb569a6e5, 0xa6d76178),
PCMCIA_DEVICE_PROD_ID12("IBM", "IBM17JSSFP20", 0xb569a6e5, 0xf2508753),
PCMCIA_DEVICE_PROD_ID12("KINGSTON", "CF8GB", 0x2e6d1829, 0xacbe682e),
......
drivers/ide/mips/au1xxx-ide.c
View file @ 2b0460b5
......@@ -351,11 +351,18 @@ static int auide_dma_setup(ide_drive_t *drive)
return 0;
}
static int auide_dma_check(ide_drive_t *drive)
static u8 auide_mdma_filter(ide_drive_t *drive)
{
u8 speed = ide_max_dma_mode(drive);
/*
* FIXME: ->white_list and ->black_list are based on completely bogus
* ->ide_dma_check implementation which didn't set neither the host
* controller timings nor the device for the desired transfer mode.
*
* They should be either removed or 0x00 MWDMA mask should be
* returned for devices on the ->black_list.
*/
if( dbdma_init_done == 0 ){
if (dbdma_init_done == 0) {
auide_hwif.white_list = ide_in_drive_list(drive->id,
dma_white_list);
auide_hwif.black_list = ide_in_drive_list(drive->id,
......@@ -366,22 +373,11 @@ static int auide_dma_check(ide_drive_t *drive)
}
/* Is the drive in our DMA black list? */
if ( auide_hwif.black_list ) {
drive->using_dma = 0;
/* Borrowed the warning message from ide-dma.c */
if (auide_hwif.black_list)
printk(KERN_WARNING "%s: Disabling DMA for %s (blacklisted)\n",
drive->name, drive->id->model);
}
else
drive->using_dma = 1;
if (drive->autodma && (speed & XFER_MODE) != XFER_PIO)
return 0;
drive->name, drive->id->model);
return -1;
return drive->hwif->mwdma_mask;
}
static int auide_dma_test_irq(ide_drive_t *drive)
......@@ -692,7 +688,8 @@ static int au_ide_probe(struct device *dev)
hwif->dma_off_quietly = &auide_dma_off_quietly;
hwif->dma_timeout = &auide_dma_timeout;
hwif->ide_dma_check = &auide_dma_check;
hwif->mdma_filter = &auide_mdma_filter;
hwif->dma_exec_cmd = &auide_dma_exec_cmd;
hwif->dma_start = &auide_dma_start;
hwif->ide_dma_end = &auide_dma_end;
......@@ -703,19 +700,14 @@ static int au_ide_probe(struct device *dev)
hwif->dma_lost_irq = &auide_dma_lost_irq;
hwif->ide_dma_on = &auide_dma_on;
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
hwif->atapi_dma = 1;
#else /* !CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA */
hwif->autodma = 0;
hwif->channel = 0;
hwif->hold = 1;
hwif->select_data = 0; /* no chipset-specific code */
hwif->config_data = 0; /* no chipset-specific code */
hwif->drives[0].autodma = 0;
hwif->drives[0].autotune = 1; /* 1=autotune, 2=noautotune, 0=default */
#endif
hwif->drives[0].no_io_32bit = 1;
......
drivers/ide/pci/aec62xx.c
View file @ 2b0460b5
/*
* linux/drivers/ide/pci/aec62xx.c Version 0.24 May 24, 2007
* linux/drivers/ide/pci/aec62xx.c Version 0.25 Aug 1, 2007
*
* Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2007 MontaVista Software, Inc. <source@mvista.com>
......@@ -141,17 +141,6 @@ static void aec_set_pio_mode(ide_drive_t *drive, const u8 pio)
drive->hwif->set_dma_mode(drive, pio + XFER_PIO_0);
}
static int aec62xx_config_drive_xfer_rate (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
static void aec62xx_dma_lost_irq (ide_drive_t *drive)
{
switch (HWIF(drive)->pci_dev->device) {
......@@ -207,15 +196,14 @@ static void __devinit init_hwif_aec62xx(ide_hwif_t *hwif)
} else
hwif->set_dma_mode = &aec6260_set_mode;
if (!hwif->dma_base) {
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
if (hwif->dma_base == 0)
return;
}
hwif->ultra_mask = hwif->cds->udma_mask;
hwif->mwdma_mask = 0x07;
hwif->ide_dma_check = &aec62xx_config_drive_xfer_rate;
hwif->dma_lost_irq = &aec62xx_dma_lost_irq;
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
......@@ -230,10 +218,6 @@ static void __devinit init_hwif_aec62xx(ide_hwif_t *hwif)
hwif->cbl = (ata66 & mask) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static int __devinit init_setup_aec62xx(struct pci_dev *dev, ide_pci_device_t *d)
......@@ -325,12 +309,12 @@ static int __devinit aec62xx_init_one(struct pci_dev *dev, const struct pci_devi
return d.init_setup(dev, &d);
}
static struct pci_device_id aec62xx_pci_tbl[] = {
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP850UF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP860, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP860R, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP865, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP865R, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
static const struct pci_device_id aec62xx_pci_tbl[] = {
{ PCI_VDEVICE(ARTOP, PCI_DEVICE_ID_ARTOP_ATP850UF), 0 },
{ PCI_VDEVICE(ARTOP, PCI_DEVICE_ID_ARTOP_ATP860), 1 },
{ PCI_VDEVICE(ARTOP, PCI_DEVICE_ID_ARTOP_ATP860R), 2 },
{ PCI_VDEVICE(ARTOP, PCI_DEVICE_ID_ARTOP_ATP865), 3 },
{ PCI_VDEVICE(ARTOP, PCI_DEVICE_ID_ARTOP_ATP865R), 4 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, aec62xx_pci_tbl);
......
drivers/ide/pci/alim15x3.c
View file @ 2b0460b5
......@@ -436,26 +436,6 @@ static void ali_set_dma_mode(ide_drive_t *drive, const u8 speed)
}
}
/**
* ali15x3_config_drive_for_dma - configure for DMA
* @drive: drive to configure
*
* Configure a drive for DMA operation. If DMA is not possible we
* drop the drive into PIO mode instead.
*/
static int ali15x3_config_drive_for_dma(ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
ide_set_max_pio(drive);
return -1;
}
/**
* ali15x3_dma_setup - begin a DMA phase
* @drive: target device
......@@ -680,7 +660,6 @@ static u8 __devinit ata66_ali15x3(ide_hwif_t *hwif)
static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
{
hwif->autodma = 0;
hwif->set_pio_mode = &ali_set_pio_mode;
hwif->set_dma_mode = &ali_set_dma_mode;
hwif->udma_filter = &ali_udma_filter;
......@@ -715,17 +694,10 @@ static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
hwif->ide_dma_check = &ali15x3_config_drive_for_dma;
hwif->dma_setup = &ali15x3_dma_setup;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_ali15x3(hwif);
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
/**
......@@ -836,9 +808,9 @@ static int __devinit alim15x3_init_one(struct pci_dev *dev, const struct pci_dev
}
static struct pci_device_id alim15x3_pci_tbl[] = {
{ PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5229, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5228, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
static const struct pci_device_id alim15x3_pci_tbl[] = {
{ PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), 0 },
{ PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, alim15x3_pci_tbl);
......
drivers/ide/pci/amd74xx.c
View file @ 2b0460b5
This diff is collapsed.
drivers/ide/pci/atiixp.c
View file @ 2b0460b5
/*
* linux/drivers/ide/pci/atiixp.c Version 0.02 Jun 16 2007
* linux/drivers/ide/pci/atiixp.c Version 0.03 Aug 3 2007
*
* Copyright (C) 2003 ATI Inc. <hyu@ati.com>
* Copyright (C) 2004,2007 Bartlomiej Zolnierkiewicz
......@@ -47,43 +47,6 @@ static int save_mdma_mode[4];
static DEFINE_SPINLOCK(atiixp_lock);
/**
* atiixp_dma_2_pio - return the PIO mode matching DMA
* @xfer_rate: transfer speed
*
* Returns the nearest equivalent PIO timing for the PIO or DMA
* mode requested by the controller.
*/
static u8 atiixp_dma_2_pio(u8 xfer_rate) {
switch(xfer_rate) {
case XFER_UDMA_6:
case XFER_UDMA_5:
case XFER_UDMA_4:
case XFER_UDMA_3:
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
case XFER_MW_DMA_2:
case XFER_PIO_4:
return 4;
case XFER_MW_DMA_1:
case XFER_PIO_3:
return 3;
case XFER_SW_DMA_2:
case XFER_PIO_2:
return 2;
case XFER_MW_DMA_0:
case XFER_SW_DMA_1:
case XFER_SW_DMA_0:
case XFER_PIO_1:
case XFER_PIO_0:
case XFER_PIO_SLOW:
default:
return 0;
}
}
static void atiixp_dma_host_on(ide_drive_t *drive)
{
struct pci_dev *dev = drive->hwif->pci_dev;
......@@ -169,7 +132,9 @@ static void atiixp_set_dma_mode(ide_drive_t *drive, const u8 speed)
int timing_shift = (drive->dn & 2) ? 16 : 0 + (drive->dn & 1) ? 0 : 8;
u32 tmp32;
u16 tmp16;
u8 pio;
if (speed < XFER_MW_DMA_0)
return;
spin_lock_irqsave(&atiixp_lock, flags);
......@@ -191,34 +156,6 @@ static void atiixp_set_dma_mode(ide_drive_t *drive, const u8 speed)
}
spin_unlock_irqrestore(&atiixp_lock, flags);
if (speed >= XFER_SW_DMA_0)
pio = atiixp_dma_2_pio(speed);
else
pio = speed - XFER_PIO_0;
atiixp_set_pio_mode(drive, pio);
}
/**
* atiixp_dma_check - set up an IDE device
* @drive: IDE drive to configure
*
* Set up the ATIIXP interface for the best available speed on this
* interface, preferring DMA to PIO.
*/
static int atiixp_dma_check(ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
/**
......@@ -238,7 +175,6 @@ static void __devinit init_hwif_atiixp(ide_hwif_t *hwif)
if (!hwif->irq)
hwif->irq = ch ? 15 : 14;
hwif->autodma = 0;
hwif->set_pio_mode = &atiixp_set_pio_mode;
hwif->set_dma_mode = &atiixp_set_dma_mode;
hwif->drives[0].autotune = 1;
......@@ -249,8 +185,7 @@ static void __devinit init_hwif_atiixp(ide_hwif_t *hwif)
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x3f;
hwif->mwdma_mask = 0x06;
hwif->swdma_mask = 0x04;
hwif->mwdma_mask = 0x07;
pci_read_config_byte(pdev, ATIIXP_IDE_UDMA_MODE + ch, &udma_mode);
......@@ -261,12 +196,6 @@ static void __devinit init_hwif_atiixp(ide_hwif_t *hwif)
hwif->dma_host_on = &atiixp_dma_host_on;
hwif->dma_host_off = &atiixp_dma_host_off;
hwif->ide_dma_check = &atiixp_dma_check;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[1].autodma = hwif->autodma;
hwif->drives[0].autodma = hwif->autodma;
}
......@@ -303,12 +232,12 @@ static int __devinit atiixp_init_one(struct pci_dev *dev, const struct pci_devic
return ide_setup_pci_device(dev, &atiixp_pci_info[id->driver_data]);
}
static struct pci_device_id atiixp_pci_tbl[] = {
{ PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP200_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id atiixp_pci_tbl[] = {
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP200_IDE), 0 },
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP300_IDE), 0 },
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP400_IDE), 0 },
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP600_IDE), 1 },
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP700_IDE), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, atiixp_pci_tbl);
......
drivers/ide/pci/cmd64x.c
View file @ 2b0460b5
......@@ -330,17 +330,6 @@ static void cmd64x_set_dma_mode(ide_drive_t *drive, const u8 speed)
(void) pci_write_config_byte(dev, pciU, regU);
}
static int cmd64x_config_drive_for_dma (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
static int cmd648_ide_dma_end (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
......@@ -547,8 +536,6 @@ static void __devinit init_hwif_cmd64x(ide_hwif_t *hwif)
if (dev->device == PCI_DEVICE_ID_CMD_646 && rev < 5)
hwif->ultra_mask = 0x00;
hwif->ide_dma_check = &cmd64x_config_drive_for_dma;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_cmd64x(hwif);
......@@ -572,10 +559,6 @@ static void __devinit init_hwif_cmd64x(ide_hwif_t *hwif)
hwif->ide_dma_test_irq = &cmd64x_ide_dma_test_irq;
break;
}
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static int __devinit init_setup_cmd64x(struct pci_dev *dev, ide_pci_device_t *d)
......@@ -654,11 +637,11 @@ static int __devinit cmd64x_init_one(struct pci_dev *dev, const struct pci_devic
return d.init_setup(dev, &d);
}
static struct pci_device_id cmd64x_pci_tbl[] = {
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_643, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_646, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_648, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_649, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
static const struct pci_device_id cmd64x_pci_tbl[] = {
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_648), 2 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_649), 3 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, cmd64x_pci_tbl);
......
drivers/ide/pci/cs5520.c
View file @ 2b0460b5
......@@ -105,15 +105,6 @@ static void cs5520_set_dma_mode(ide_drive_t *drive, const u8 speed)
cs5520_set_pio_mode(drive, 0);
}
static int cs5520_config_drive_xfer_rate(ide_drive_t *drive)
{
/* Tune the drive for PIO modes up to PIO 4 */
ide_set_max_pio(drive);
/* Then tell the core to use DMA operations */
return 0;
}
/*
* We provide a callback for our nonstandard DMA location
*/
......@@ -148,7 +139,6 @@ static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
return;
}
hwif->ide_dma_check = &cs5520_config_drive_xfer_rate;
hwif->ide_dma_on = &cs5520_dma_on;
/* ATAPI is harder so leave it for now */
......@@ -156,12 +146,6 @@ static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
hwif->ultra_mask = 0;
hwif->swdma_mask = 0;
hwif->mwdma_mask = 0;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
#define DECLARE_CS_DEV(name_str) \
......@@ -171,7 +155,8 @@ static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
.init_hwif = init_hwif_cs5520, \
.autodma = AUTODMA, \
.bootable = ON_BOARD, \
.host_flags = IDE_HFLAG_ISA_PORTS, \
.host_flags = IDE_HFLAG_ISA_PORTS | \
IDE_HFLAG_VDMA, \
.pio_mask = ATA_PIO4, \
}
......@@ -233,9 +218,9 @@ static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_devic
return 0;
}
static struct pci_device_id cs5520_pci_tbl[] = {
{ PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5510, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5520, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
static const struct pci_device_id cs5520_pci_tbl[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), 0 },
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, cs5520_pci_tbl);
......
drivers/ide/pci/cs5530.c
View file @ 2b0460b5
/*
* linux/drivers/ide/pci/cs5530.c Version 0.74 Jul 28 2007
* linux/drivers/ide/pci/cs5530.c Version 0.76 Aug 3 2007
*
* Copyright (C) 2000 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2000 Mark Lord <mlord@pobox.com>
......@@ -104,22 +104,6 @@ static u8 cs5530_udma_filter(ide_drive_t *drive)
return mask;
}
/**
* cs5530_config_dma - set DMA/UDMA mode
* @drive: drive to tune
*
* cs5530_config_dma() handles setting of DMA/UDMA mode
* for both the chipset and drive.
*/
static int cs5530_config_dma(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
return 1;
}
static void cs5530_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
unsigned long basereg;
......@@ -260,7 +244,6 @@ static void __devinit init_hwif_cs5530 (ide_hwif_t *hwif)
{
unsigned long basereg;
u32 d0_timings;
hwif->autodma = 0;
if (hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
......@@ -270,20 +253,13 @@ static void __devinit init_hwif_cs5530 (ide_hwif_t *hwif)
basereg = CS5530_BASEREG(hwif);
d0_timings = inl(basereg + 0);
if (CS5530_BAD_PIO(d0_timings)) {
/* PIO timings not initialized? */
if (CS5530_BAD_PIO(d0_timings))
outl(cs5530_pio_timings[(d0_timings >> 31) & 1][0], basereg + 0);
if (!hwif->drives[0].autotune)
hwif->drives[0].autotune = 1;
/* needs autotuning later */
}
if (CS5530_BAD_PIO(inl(basereg + 8))) {
/* PIO timings not initialized? */
if (CS5530_BAD_PIO(inl(basereg + 8)))
outl(cs5530_pio_timings[(d0_timings >> 31) & 1][0], basereg + 8);
if (!hwif->drives[1].autotune)
hwif->drives[1].autotune = 1;
/* needs autotuning later */
}
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
if (hwif->dma_base == 0)
return;
......@@ -293,11 +269,6 @@ static void __devinit init_hwif_cs5530 (ide_hwif_t *hwif)
hwif->mwdma_mask = 0x07;
hwif->udma_filter = cs5530_udma_filter;
hwif->ide_dma_check = &cs5530_config_dma;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t cs5530_chipset __devinitdata = {
......@@ -315,8 +286,8 @@ static int __devinit cs5530_init_one(struct pci_dev *dev, const struct pci_devic
return ide_setup_pci_device(dev, &cs5530_chipset);
}
static struct pci_device_id cs5530_pci_tbl[] = {
{ PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id cs5530_pci_tbl[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, cs5530_pci_tbl);
......
drivers/ide/pci/cs5535.c
View file @ 2b0460b5
......@@ -157,19 +157,6 @@ static void cs5535_set_pio_mode(ide_drive_t *drive, const u8 pio)
cs5535_set_speed(drive, XFER_PIO_0 + pio);
}
static int cs5535_dma_check(ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
static u8 __devinit cs5535_cable_detect(struct pci_dev *dev)
{
u8 bit;
......@@ -190,8 +177,6 @@ static u8 __devinit cs5535_cable_detect(struct pci_dev *dev)
*/
static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
{
hwif->autodma = 0;
hwif->set_pio_mode = &cs5535_set_pio_mode;
hwif->set_dma_mode = &cs5535_set_dma_mode;
......@@ -200,18 +185,11 @@ static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
if (hwif->dma_base == 0)
return;
hwif->ide_dma_check = &cs5535_dma_check;
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x1F;
hwif->mwdma_mask = 0x07;
hwif->cbl = cs5535_cable_detect(hwif->pci_dev);
if (!noautodma)
hwif->autodma = 1;
hwif->drives[1].autodma = hwif->drives[0].autodma = hwif->autodma;
}
static ide_pci_device_t cs5535_chipset __devinitdata = {
......@@ -229,10 +207,8 @@ static int __devinit cs5535_init_one(struct pci_dev *dev,
return ide_setup_pci_device(dev, &cs5535_chipset);
}
static struct pci_device_id cs5535_pci_tbl[] =
{
{ PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_CS5535_IDE, PCI_ANY_ID,
PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id cs5535_pci_tbl[] = {
{ PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_CS5535_IDE), 0 },
{ 0, },
};
......
drivers/ide/pci/cy82c693.c
View file @ 2b0460b5
......@@ -428,8 +428,6 @@ static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev, const c
*/
static void __devinit init_hwif_cy82c693(ide_hwif_t *hwif)
{
hwif->autodma = 0;
hwif->chipset = ide_cy82c693;
hwif->set_pio_mode = &cy82c693_set_pio_mode;
......@@ -444,10 +442,6 @@ static void __devinit init_hwif_cy82c693(ide_hwif_t *hwif)
hwif->swdma_mask = 0x04;
hwif->ide_dma_on = &cy82c693_ide_dma_on;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static __devinitdata ide_hwif_t *primary;
......@@ -469,7 +463,7 @@ static ide_pci_device_t cy82c693_chipset __devinitdata = {
.init_hwif = init_hwif_cy82c693,
.autodma = AUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_SINGLE,
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_TRUST_BIOS_FOR_DMA,
.pio_mask = ATA_PIO4,
};
......@@ -489,8 +483,8 @@ static int __devinit cy82c693_init_one(struct pci_dev *dev, const struct pci_dev
return ret;
}
static struct pci_device_id cy82c693_pci_tbl[] = {
{ PCI_VENDOR_ID_CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id cy82c693_pci_tbl[] = {
{ PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, cy82c693_pci_tbl);
......
drivers/ide/pci/generic.c
View file @ 2b0460b5
......@@ -73,11 +73,6 @@ static void __devinit init_hwif_generic (ide_hwif_t *hwif)
hwif->ultra_mask = 0x7f;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
#if 0
......@@ -97,77 +92,92 @@ static ide_pci_device_t generic_chipsets[] __devinitdata = {
.init_hwif = init_hwif_generic,
.autodma = AUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 1 */
.name = "NS87410",
.init_hwif = init_hwif_generic,
.autodma = AUTODMA,
.enablebits = {{0x43,0x08,0x08}, {0x47,0x08,0x08}},
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 2 */
.name = "SAMURAI",
.init_hwif = init_hwif_generic,
.autodma = AUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 3 */
.name = "HT6565",
.init_hwif = init_hwif_generic,
.autodma = AUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 4 */
.name = "UM8673F",
.init_hwif = init_hwif_generic,
.autodma = NODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 5 */
.name = "UM8886A",
.init_hwif = init_hwif_generic,
.autodma = NODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 6 */
.name = "UM8886BF",
.init_hwif = init_hwif_generic,
.autodma = NODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 7 */
.name = "HINT_IDE",
.init_hwif = init_hwif_generic,
.autodma = AUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 8 */
.name = "VIA_IDE",
.init_hwif = init_hwif_generic,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 9 */
.name = "OPTI621V",
.init_hwif = init_hwif_generic,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 10 */
.name = "VIA8237SATA",
.init_hwif = init_hwif_generic,
.autodma = AUTODMA,
.bootable = OFF_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 11 */
.name = "Piccolo0102",
.init_hwif = init_hwif_generic,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 12 */
.name = "Piccolo0103",
.init_hwif = init_hwif_generic,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 13 */
.name = "Piccolo0105",
.init_hwif = init_hwif_generic,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 14 */
.name = "Revolution",
.init_hwif = init_hwif_generic,
.autodma = AUTODMA,
.bootable = OFF_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
}
};
......@@ -226,25 +236,28 @@ static int __devinit generic_init_one(struct pci_dev *dev, const struct pci_devi
return ret;
}
static struct pci_device_id generic_pci_tbl[] = {
{ PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_SAMURAI_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VENDOR_ID_HOLTEK, PCI_DEVICE_ID_HOLTEK_6565, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
{ PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8673F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
{ PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
{ PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
{ PCI_VENDOR_ID_HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7},
{ PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C561, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8},
{ PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C558, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9},
static const struct pci_device_id generic_pci_tbl[] = {
{ PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_87410), 1 },
{ PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_SAMURAI_IDE), 2 },
{ PCI_VDEVICE(HOLTEK, PCI_DEVICE_ID_HOLTEK_6565), 3 },
{ PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8673F), 4 },
{ PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8886A), 5 },
{ PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8886BF), 6 },
{ PCI_VDEVICE(HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE), 7 },
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C561), 8 },
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C558), 9 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237_SATA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10},
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_8237_SATA), 10 },
#endif
{ PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11},
{ PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12},
{ PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13},
{ PCI_VENDOR_ID_NETCELL,PCI_DEVICE_ID_REVOLUTION, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 14},
/* Must come last. If you add entries adjust this table appropriately and the init_one code */
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 0},
{ PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO), 11 },
{ PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), 12 },
{ PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), 13 },
{ PCI_VDEVICE(NETCELL, PCI_DEVICE_ID_REVOLUTION), 14 },
/*
* Must come last. If you add entries adjust
* this table and generic_chipsets[] appropriately.
*/
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, generic_pci_tbl);
......
drivers/ide/pci/hpt34x.c
View file @ 2b0460b5
......@@ -80,19 +80,6 @@ static void hpt34x_set_pio_mode(ide_drive_t *drive, const u8 pio)
hpt34x_set_mode(drive, XFER_PIO_0 + pio);
}
static int hpt34x_config_drive_xfer_rate (ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return -1;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
/*
* If the BIOS does not set the IO base addaress to XX00, 343 will fail.
*/
......@@ -140,8 +127,6 @@ static void __devinit init_hwif_hpt34x(ide_hwif_t *hwif)
{
u16 pcicmd = 0;
hwif->autodma = 0;
hwif->set_pio_mode = &hpt34x_set_pio_mode;
hwif->set_dma_mode = &hpt34x_set_mode;
......@@ -154,16 +139,13 @@ static void __devinit init_hwif_hpt34x(ide_hwif_t *hwif)
return;
#ifdef CONFIG_HPT34X_AUTODMA
if ((pcicmd & PCI_COMMAND_MEMORY) == 0)
return;
hwif->ultra_mask = 0x07;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
#endif
hwif->ide_dma_check = &hpt34x_config_drive_xfer_rate;
if (!noautodma)
hwif->autodma = (pcicmd & PCI_COMMAND_MEMORY) ? 1 : 0;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t hpt34x_chipset __devinitdata = {
......@@ -190,8 +172,8 @@ static int __devinit hpt34x_init_one(struct pci_dev *dev, const struct pci_devic
return ide_setup_pci_device(dev, d);
}
static struct pci_device_id hpt34x_pci_tbl[] = {
{ PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT343, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id hpt34x_pci_tbl[] = {
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, hpt34x_pci_tbl);
......
drivers/ide/pci/hpt366.c
View file @ 2b0460b5
/*
* linux/drivers/ide/pci/hpt366.c Version 1.13 Sep 29, 2007
* linux/drivers/ide/pci/hpt366.c Version 1.14 Oct 1, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
......@@ -713,19 +713,6 @@ static void hpt3xx_maskproc(ide_drive_t *drive, int mask)
IDE_CONTROL_REG);
}
static int hpt366_config_drive_xfer_rate(ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
/*
* This is specific to the HPT366 UDMA chipset
* by HighPoint|Triones Technologies, Inc.
......@@ -1304,10 +1291,10 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
if (new_mcr != old_mcr)
pci_write_config_byte(dev, hwif->select_data + 1, new_mcr);
if (!hwif->dma_base) {
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
if (hwif->dma_base == 0)
return;
}
hwif->ultra_mask = hwif->cds->udma_mask;
hwif->mwdma_mask = 0x07;
......@@ -1349,8 +1336,6 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = (scr1 & ata66) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
hwif->ide_dma_check = &hpt366_config_drive_xfer_rate;
if (chip_type >= HPT374) {
hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
hwif->ide_dma_end = &hpt374_ide_dma_end;
......@@ -1360,10 +1345,6 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
hwif->dma_timeout = &hpt370_dma_timeout;
} else
hwif->dma_lost_irq = &hpt366_dma_lost_irq;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
......@@ -1657,13 +1638,13 @@ static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_devic
return d.init_setup(dev, &d);
}
static struct pci_device_id hpt366_pci_tbl[] = {
{ PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
{ PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
{ PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
static const struct pci_device_id hpt366_pci_tbl[] = {
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), 0 },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), 1 },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), 2 },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), 3 },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), 4 },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), 5 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl);
......
drivers/ide/pci/it8213.c
View file @ 2b0460b5
......@@ -17,37 +17,6 @@
#include <asm/io.h>
/**
* it8213_dma_2_pio - return the PIO mode matching DMA
* @xfer_rate: transfer speed
*
* Returns the nearest equivalent PIO timing for the DMA
* mode requested by the controller.
*/
static u8 it8213_dma_2_pio (u8 xfer_rate) {
switch(xfer_rate) {
case XFER_UDMA_6:
case XFER_UDMA_5:
case XFER_UDMA_4:
case XFER_UDMA_3:
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
case XFER_MW_DMA_2:
return 4;
case XFER_MW_DMA_1:
return 3;
case XFER_SW_DMA_2:
return 2;
case XFER_MW_DMA_0:
case XFER_SW_DMA_1:
case XFER_SW_DMA_0:
default:
return 0;
}
}
/**
* it8213_set_pio_mode - set host controller for PIO mode
* @drive: drive
......@@ -166,6 +135,9 @@ static void it8213_set_dma_mode(ide_drive_t *drive, const u8 speed)
} else
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
} else {
const u8 mwdma_to_pio[] = { 0, 3, 4 };
u8 pio;
if (reg48 & u_flag)
pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
if (reg4a & a_speed)
......@@ -174,38 +146,21 @@ static void it8213_set_dma_mode(ide_drive_t *drive, const u8 speed)
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
if (reg55 & w_flag)
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
}
it8213_set_pio_mode(drive, it8213_dma_2_pio(speed));
}
/**
* it8213_configure_drive_for_dma - set up for DMA transfers
* @drive: drive we are going to set up
*
* Set up the drive for DMA, tune the controller and drive as
* required. If the drive isn't suitable for DMA or we hit
* other problems then we will drop down to PIO and set up
* PIO appropriately
*/
static int it8213_config_drive_for_dma (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (speed >= XFER_MW_DMA_0)
pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
else
pio = 2; /* only SWDMA2 is allowed */
ide_set_max_pio(drive);
return -1;
it8213_set_pio_mode(drive, pio);
}
}
/**
* init_hwif_it8213 - set up hwif structs
* @hwif: interface to set up
*
* We do the basic set up of the interface structure. The IT8212
* requires several custom handlers so we override the default
* ide DMA handlers appropriately
* We do the basic set up of the interface structure.
*/
static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
......@@ -215,8 +170,6 @@ static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
hwif->set_dma_mode = &it8213_set_dma_mode;
hwif->set_pio_mode = &it8213_set_pio_mode;
hwif->autodma = 0;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
......@@ -230,20 +183,8 @@ static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
pci_read_config_byte(hwif->pci_dev, 0x42, &reg42h);
hwif->ide_dma_check = &it8213_config_drive_for_dma;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = (reg42h & 0x02) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
/*
* The BIOS often doesn't set up DMA on this controller
* so we always do it.
*/
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
......@@ -279,9 +220,8 @@ static int __devinit it8213_init_one(struct pci_dev *dev, const struct pci_devic
return 0;
}
static struct pci_device_id it8213_pci_tbl[] = {
{ PCI_VENDOR_ID_ITE, 0x8213, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
static const struct pci_device_id it8213_pci_tbl[] = {
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), 0 },
{ 0, },
};
......
drivers/ide/pci/it821x.c
View file @ 2b0460b5
......@@ -415,26 +415,6 @@ static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed)
it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
}
/**
* it821x_configure_drive_for_dma - set up for DMA transfers
* @drive: drive we are going to set up
*
* Set up the drive for DMA, tune the controller and drive as
* required. If the drive isn't suitable for DMA or we hit
* other problems then we will drop down to PIO and set up
* PIO appropriately
*/
static int it821x_config_drive_for_dma (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
ide_set_max_pio(drive);
return -1;
}
/**
* ata66_it821x - check for 80 pin cable
* @hwif: interface to check
......@@ -557,10 +537,11 @@ static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
struct it821x_dev *idev = kzalloc(sizeof(struct it821x_dev), GFP_KERNEL);
u8 conf;
if(idev == NULL) {
if (idev == NULL) {
printk(KERN_ERR "it821x: out of memory, falling back to legacy behaviour.\n");
goto fallback;
return;
}
ide_set_hwifdata(hwif, idev);
hwif->atapi_dma = 1;
......@@ -609,29 +590,14 @@ static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
if (!hwif->dma_base)
goto fallback;
if (hwif->dma_base == 0)
return;
hwif->ultra_mask = 0x7f;
hwif->mwdma_mask = 0x07;
hwif->ide_dma_check = &it821x_config_drive_for_dma;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_it821x(hwif);
/*
* The BIOS often doesn't set up DMA on this controller
* so we always do it.
*/
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
return;
fallback:
hwif->autodma = 0;
return;
}
static void __devinit it8212_disable_raid(struct pci_dev *dev)
......@@ -697,9 +663,9 @@ static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_devic
return 0;
}
static struct pci_device_id it821x_pci_tbl[] = {
{ PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id it821x_pci_tbl[] = {
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 },
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 },
{ 0, },
};
......
drivers/ide/pci/jmicron.c
View file @ 2b0460b5
......@@ -99,24 +99,6 @@ static void jmicron_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
}
/**
* jmicron_configure_drive_for_dma - set up for DMA transfers
* @drive: drive we are going to set up
*
* As the JMicron snoops for timings all we actually need to do is
* make sure we don't set an invalid mode.
*/
static int jmicron_config_drive_for_dma (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
ide_set_max_pio(drive);
return -1;
}
/**
* init_hwif_jmicron - set up hwif structs
* @hwif: interface to set up
......@@ -132,25 +114,15 @@ static void __devinit init_hwif_jmicron(ide_hwif_t *hwif)
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
if (!hwif->dma_base)
goto fallback;
if (hwif->dma_base == 0)
return;
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x7f;
hwif->mwdma_mask = 0x07;
hwif->ide_dma_check = &jmicron_config_drive_for_dma;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_jmicron(hwif);
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
return;
fallback:
hwif->autodma = 0;
return;
}
static ide_pci_device_t jmicron_chipset __devinitdata = {
......
drivers/ide/pci/ns87415.c
View file @ 2b0460b5
......@@ -197,7 +197,6 @@ static void __devinit init_hwif_ns87415 (ide_hwif_t *hwif)
u8 stat;
#endif
hwif->autodma = 0;
hwif->selectproc = &ns87415_selectproc;
/*
......@@ -259,11 +258,6 @@ static void __devinit init_hwif_ns87415 (ide_hwif_t *hwif)
outb(0x60, hwif->dma_status);
hwif->dma_setup = &ns87415_ide_dma_setup;
hwif->ide_dma_end = &ns87415_ide_dma_end;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t ns87415_chipset __devinitdata = {
......@@ -274,6 +268,7 @@ static ide_pci_device_t ns87415_chipset __devinitdata = {
.init_hwif = init_hwif_ns87415,
.autodma = AUTODMA,
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
};
static int __devinit ns87415_init_one(struct pci_dev *dev, const struct pci_device_id *id)
......@@ -281,8 +276,8 @@ static int __devinit ns87415_init_one(struct pci_dev *dev, const struct pci_devi
return ide_setup_pci_device(dev, &ns87415_chipset);
}
static struct pci_device_id ns87415_pci_tbl[] = {
{ PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id ns87415_pci_tbl[] = {
{ PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_87415), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, ns87415_pci_tbl);
......
drivers/ide/pci/opti621.c
View file @ 2b0460b5
......@@ -328,7 +328,6 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
*/
static void __devinit init_hwif_opti621 (ide_hwif_t *hwif)
{
hwif->autodma = 0;
hwif->drives[0].drive_data = PIO_DONT_KNOW;
hwif->drives[1].drive_data = PIO_DONT_KNOW;
......@@ -340,11 +339,6 @@ static void __devinit init_hwif_opti621 (ide_hwif_t *hwif)
hwif->atapi_dma = 1;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t opti621_chipsets[] __devinitdata = {
......@@ -355,6 +349,7 @@ static ide_pci_device_t opti621_chipsets[] __devinitdata = {
.enablebits = {{0x45,0x80,0x00}, {0x40,0x08,0x00}},
.bootable = ON_BOARD,
.pio_mask = ATA_PIO3,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 1 */
.name = "OPTI621X",
.init_hwif = init_hwif_opti621,
......@@ -362,6 +357,7 @@ static ide_pci_device_t opti621_chipsets[] __devinitdata = {
.enablebits = {{0x45,0x80,0x00}, {0x40,0x08,0x00}},
.bootable = ON_BOARD,
.pio_mask = ATA_PIO3,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
}
};
......@@ -370,9 +366,9 @@ static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_devi
return ide_setup_pci_device(dev, &opti621_chipsets[id->driver_data]);
}
static struct pci_device_id opti621_pci_tbl[] = {
{ PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C621, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
static const struct pci_device_id opti621_pci_tbl[] = {
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);
......
drivers/ide/pci/pdc202xx_new.c
View file @ 2b0460b5
......@@ -223,19 +223,6 @@ static u8 pdcnew_cable_detect(ide_hwif_t *hwif)
return ATA_CBL_PATA80;
}
static int pdcnew_config_drive_xfer_rate(ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
static int pdcnew_quirkproc(ide_drive_t *drive)
{
const char **list, *model = drive->id->model;
......@@ -482,8 +469,6 @@ static unsigned int __devinit init_chipset_pdcnew(struct pci_dev *dev, const cha
static void __devinit init_hwif_pdc202new(ide_hwif_t *hwif)
{
hwif->autodma = 0;
hwif->set_pio_mode = &pdcnew_set_pio_mode;
hwif->set_dma_mode = &pdcnew_set_mode;
......@@ -502,14 +487,8 @@ static void __devinit init_hwif_pdc202new(ide_hwif_t *hwif)
hwif->ultra_mask = hwif->cds->udma_mask;
hwif->mwdma_mask = 0x07;
hwif->ide_dma_check = &pdcnew_config_drive_xfer_rate;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = pdcnew_cable_detect(hwif);
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static int __devinit init_setup_pdcnew(struct pci_dev *dev, ide_pci_device_t *d)
......@@ -658,14 +637,14 @@ static int __devinit pdc202new_init_one(struct pci_dev *dev, const struct pci_de
return d->init_setup(dev, d);
}
static struct pci_device_id pdc202new_pci_tbl[] = {
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20268, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20269, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20270, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20271, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20275, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20276, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20277, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
static const struct pci_device_id pdc202new_pci_tbl[] = {
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), 0 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), 1 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 2 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 3 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 4 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 5 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 6 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, pdc202new_pci_tbl);
......
drivers/ide/pci/pdc202xx_old.c
View file @ 2b0460b5
......@@ -179,19 +179,6 @@ static void pdc_old_disable_66MHz_clock(ide_hwif_t *hwif)
outb(clock & ~(hwif->channel ? 0x08 : 0x02), clock_reg);
}
static int pdc202xx_config_drive_xfer_rate (ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
static int pdc202xx_quirkproc (ide_drive_t *drive)
{
const char **list, *model = drive->id->model;
......@@ -325,8 +312,6 @@ static void __devinit init_hwif_pdc202xx(ide_hwif_t *hwif)
(dev->device == PCI_DEVICE_ID_PROMISE_20265))
hwif->rqsize = 256;
hwif->autodma = 0;
hwif->set_pio_mode = &pdc202xx_set_pio_mode;
hwif->set_dma_mode = &pdc202xx_set_mode;
......@@ -347,7 +332,6 @@ static void __devinit init_hwif_pdc202xx(ide_hwif_t *hwif)
hwif->swdma_mask = 0x07;
hwif->atapi_dma = 1;
hwif->ide_dma_check = &pdc202xx_config_drive_xfer_rate;
hwif->dma_lost_irq = &pdc202xx_dma_lost_irq;
hwif->dma_timeout = &pdc202xx_dma_timeout;
......@@ -359,10 +343,6 @@ static void __devinit init_hwif_pdc202xx(ide_hwif_t *hwif)
hwif->ide_dma_end = &pdc202xx_old_ide_dma_end;
}
hwif->ide_dma_test_irq = &pdc202xx_old_ide_dma_test_irq;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static void __devinit init_dma_pdc202xx(ide_hwif_t *hwif, unsigned long dmabase)
......@@ -510,12 +490,12 @@ static int __devinit pdc202xx_init_one(struct pci_dev *dev, const struct pci_dev
return d->init_setup(dev, d);
}
static struct pci_device_id pdc202xx_pci_tbl[] = {
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20246, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20262, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20263, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20265, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
{ PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20267, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
static const struct pci_device_id pdc202xx_pci_tbl[] = {
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 2 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 3 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 4 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, pdc202xx_pci_tbl);
......
drivers/ide/pci/piix.c
View file @ 2b0460b5
/*
* linux/drivers/ide/pci/piix.c Version 0.52 Jul 14, 2007
* linux/drivers/ide/pci/piix.c Version 0.53 Aug 9, 2007
*
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
......@@ -105,37 +105,6 @@
static int no_piix_dma;
/**
* piix_dma_2_pio - return the PIO mode matching DMA
* @xfer_rate: transfer speed
*
* Returns the nearest equivalent PIO timing for the DMA
* mode requested by the controller.
*/
static u8 piix_dma_2_pio (u8 xfer_rate) {
switch(xfer_rate) {
case XFER_UDMA_6:
case XFER_UDMA_5:
case XFER_UDMA_4:
case XFER_UDMA_3:
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
case XFER_MW_DMA_2:
return 4;
case XFER_MW_DMA_1:
return 3;
case XFER_SW_DMA_2:
return 2;
case XFER_MW_DMA_0:
case XFER_SW_DMA_1:
case XFER_SW_DMA_0:
default:
return 0;
}
}
/**
* piix_set_pio_mode - set host controller for PIO mode
* @drive: drive
......@@ -263,6 +232,9 @@ static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
} else
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
} else {
const u8 mwdma_to_pio[] = { 0, 3, 4 };
u8 pio;
if (reg48 & u_flag)
pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
if (reg4a & a_speed)
......@@ -271,30 +243,14 @@ static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
if (reg55 & w_flag)
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
}
piix_set_pio_mode(drive, piix_dma_2_pio(speed));
}
/**
* piix_config_drive_xfer_rate - set up an IDE device
* @drive: IDE drive to configure
*
* Set up the PIIX interface for the best available speed on this
* interface, preferring DMA to PIO.
*/
static int piix_config_drive_xfer_rate (ide_drive_t *drive)
{
drive->init_speed = 0;
if (speed >= XFER_MW_DMA_0)
pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
else
pio = 2; /* only SWDMA2 is allowed */
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
piix_set_pio_mode(drive, pio);
}
}
/**
......@@ -428,8 +384,6 @@ static void __devinit init_hwif_piix(ide_hwif_t *hwif)
return;
}
hwif->autodma = 0;
hwif->set_pio_mode = &piix_set_pio_mode;
hwif->set_dma_mode = &piix_set_dma_mode;
......@@ -456,13 +410,6 @@ static void __devinit init_hwif_piix(ide_hwif_t *hwif)
if (no_piix_dma)
hwif->ultra_mask = hwif->mwdma_mask = hwif->swdma_mask = 0;
hwif->ide_dma_check = &piix_config_drive_xfer_rate;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[1].autodma = hwif->autodma;
hwif->drives[0].autodma = hwif->autodma;
}
#define DECLARE_PIIX_DEV(name_str, udma) \
......@@ -565,34 +512,34 @@ static void __devinit piix_check_450nx(void)
printk(KERN_WARNING "piix: A BIOS update may resolve this.\n");
}
static struct pci_device_id piix_pci_tbl[] = {
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82372FB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_9, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_8, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 14},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 15},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801E_11, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 16},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_10,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 17},
static const struct pci_device_id piix_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_0), 0 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_1), 1 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), 2 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371SB_1), 3 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371AB), 4 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AB_1), 5 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82443MX_1), 6 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AA_1), 7 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82372FB_1), 8 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82451NX), 9 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_9), 10 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_8), 11 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_10), 12 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_11), 13 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_11), 14 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_11), 15 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801E_11), 16 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_10), 17 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 18},
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_1), 18 },
#endif
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 19},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_19, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 20},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 21},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 22},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_18, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 23},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 24},
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB_2), 19 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH6_19), 20 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH7_21), 21 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_1), 22 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB2_18), 23 },
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH8_6), 24 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
......
drivers/ide/pci/rz1000.c
View file @ 2b0460b5
......@@ -61,9 +61,9 @@ static int __devinit rz1000_init_one(struct pci_dev *dev, const struct pci_devic
return ide_setup_pci_device(dev, &rz1000_chipset);
}
static struct pci_device_id rz1000_pci_tbl[] = {
{ PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1000, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1001, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id rz1000_pci_tbl[] = {
{ PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_RZ1000), 0 },
{ PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_RZ1001), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, rz1000_pci_tbl);
......
drivers/ide/pci/sc1200.c
View file @ 2b0460b5
/*
* linux/drivers/ide/pci/sc1200.c Version 0.95 Jun 16 2007
* linux/drivers/ide/pci/sc1200.c Version 0.97 Aug 3 2007
*
* Copyright (C) 2000-2002 Mark Lord <mlord@pobox.com>
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
......@@ -199,19 +199,6 @@ static void sc1200_set_dma_mode(ide_drive_t *drive, const u8 mode)
}
}
/*
* sc1200_config_dma() handles selection/setting of DMA/UDMA modes
* for both the chipset and drive.
*/
static int sc1200_config_dma (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
return 1;
}
/* Replacement for the standard ide_dma_end action in
* dma_proc.
*
......@@ -377,27 +364,22 @@ static void __devinit init_hwif_sc1200 (ide_hwif_t *hwif)
{
if (hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
hwif->autodma = 0;
hwif->set_pio_mode = &sc1200_set_pio_mode;
hwif->set_dma_mode = &sc1200_set_dma_mode;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
if (hwif->dma_base == 0)
return;
hwif->udma_filter = sc1200_udma_filter;
hwif->ide_dma_check = &sc1200_config_dma;
hwif->ide_dma_end = &sc1200_ide_dma_end;
if (!noautodma)
hwif->autodma = 1;
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x07;
hwif->mwdma_mask = 0x07;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t sc1200_chipset __devinitdata = {
......@@ -414,8 +396,8 @@ static int __devinit sc1200_init_one(struct pci_dev *dev, const struct pci_devic
return ide_setup_pci_device(dev, &sc1200_chipset);
}
static struct pci_device_id sc1200_pci_tbl[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_IDE), 0},
static const struct pci_device_id sc1200_pci_tbl[] = {
{ PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_SCx200_IDE), 0},
{ 0, },
};
MODULE_DEVICE_TABLE(pci, sc1200_pci_tbl);
......
drivers/ide/pci/scc_pata.c
View file @ 2b0460b5
......@@ -283,28 +283,6 @@ static void scc_set_dma_mode(ide_drive_t *drive, const u8 speed)
out_be32((void __iomem *)udenvt_port, reg);
}
/**
* scc_configure_drive_for_dma - set up for DMA transfers
* @drive: drive we are going to set up
*
* Set up the drive for DMA, tune the controller and drive as
* required.
* If the drive isn't suitable for DMA or we hit other problems
* then we will drop down to PIO and set up PIO appropriately.
* (return -1)
*/
static int scc_config_drive_for_dma(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
/**
* scc_ide_dma_setup - begin a DMA phase
* @drive: target device
......@@ -702,7 +680,6 @@ static void __devinit init_hwif_scc(ide_hwif_t *hwif)
hwif->ide_dma_end = scc_ide_dma_end;
hwif->set_pio_mode = scc_set_pio_mode;
hwif->set_dma_mode = scc_set_dma_mode;
hwif->ide_dma_check = scc_config_drive_for_dma;
hwif->ide_dma_test_irq = scc_dma_test_irq;
hwif->udma_filter = scc_udma_filter;
......@@ -720,12 +697,6 @@ static void __devinit init_hwif_scc(ide_hwif_t *hwif)
/* we support 80c cable only. */
hwif->cbl = ATA_CBL_PATA80;
hwif->autodma = 0;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
#define DECLARE_SCC_DEV(name_str) \
......@@ -793,8 +764,8 @@ static void __devexit scc_remove(struct pci_dev *dev)
memset(ports, 0, sizeof(*ports));
}
static struct pci_device_id scc_pci_tbl[] = {
{ PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id scc_pci_tbl[] = {
{ PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, scc_pci_tbl);
......
drivers/ide/pci/serverworks.c
View file @ 2b0460b5
......@@ -97,6 +97,7 @@ static u8 svwks_udma_filter(ide_drive_t *drive)
mode = 2;
switch(mode) {
case 3: mask = 0x3f; break;
case 2: mask = 0x1f; break;
case 1: mask = 0x07; break;
default: mask = 0x00; break;
......@@ -195,19 +196,6 @@ static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
pci_write_config_byte(dev, 0x54, ultra_enable);
}
static int svwks_config_drive_xfer_rate (ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
static unsigned int __devinit init_chipset_svwks (struct pci_dev *dev, const char *name)
{
unsigned int reg;
......@@ -386,23 +374,16 @@ static void __devinit init_hwif_svwks (ide_hwif_t *hwif)
hwif->mwdma_mask = 0x07;
hwif->autodma = 0;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
if (!hwif->dma_base)
return;
hwif->ide_dma_check = &svwks_config_drive_xfer_rate;
if (hwif->pci_dev->device != PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_svwks(hwif);
}
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = 1;
}
static int __devinit init_setup_svwks (struct pci_dev *dev, ide_pci_device_t *d)
......@@ -490,12 +471,12 @@ static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device
return d->init_setup(dev, d);
}
static struct pci_device_id svwks_pci_tbl[] = {
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
static const struct pci_device_id svwks_pci_tbl[] = {
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0 },
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 1 },
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2 },
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 3 },
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
......
drivers/ide/pci/sgiioc4.c
View file @ 2b0460b5
......@@ -296,20 +296,6 @@ static void sgiioc4_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
}
static int sgiioc4_ide_dma_check(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
/*
* ->set_pio_mode is not implemented currently
* so this is just for the completness
*/
ide_set_max_pio(drive);
return -1;
}
/* returns 1 if dma irq issued, 0 otherwise */
static int
sgiioc4_ide_dma_test_irq(ide_drive_t * drive)
......@@ -612,7 +598,6 @@ ide_init_sgiioc4(ide_hwif_t * hwif)
hwif->dma_setup = &sgiioc4_ide_dma_setup;
hwif->dma_start = &sgiioc4_ide_dma_start;
hwif->ide_dma_end = &sgiioc4_ide_dma_end;
hwif->ide_dma_check = &sgiioc4_ide_dma_check;
hwif->ide_dma_on = &sgiioc4_ide_dma_on;
hwif->dma_off_quietly = &sgiioc4_dma_off_quietly;
hwif->ide_dma_test_irq = &sgiioc4_ide_dma_test_irq;
......@@ -689,12 +674,7 @@ sgiioc4_ide_setup_pci_device(struct pci_dev *dev)
/* Initializing chipset IRQ Registers */
writel(0x03, (void __iomem *)(irqport + IOC4_INTR_SET * 4));
hwif->autodma = 0;
if (dma_base && ide_dma_sgiioc4(hwif, dma_base) == 0) {
hwif->autodma = 1;
hwif->drives[1].autodma = hwif->drives[0].autodma = 1;
} else
if (dma_base == 0 || ide_dma_sgiioc4(hwif, dma_base))
printk(KERN_INFO "%s: %s Bus-Master DMA disabled\n",
hwif->name, DRV_NAME);
......
drivers/ide/pci/siimage.c
View file @ 2b0460b5
......@@ -311,27 +311,6 @@ static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed)
}
}
/**
* siimage_configure_drive_for_dma - set up for DMA transfers
* @drive: drive we are going to set up
*
* Set up the drive for DMA, tune the controller and drive as
* required. If the drive isn't suitable for DMA or we hit
* other problems then we will drop down to PIO and set up
* PIO appropriately
*/
static int siimage_config_drive_for_dma (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
/* returns 1 if dma irq issued, 0 otherwise */
static int siimage_io_ide_dma_test_irq (ide_drive_t *drive)
{
......@@ -894,8 +873,6 @@ static u8 __devinit ata66_siimage(ide_hwif_t *hwif)
static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
{
hwif->autodma = 0;
hwif->resetproc = &siimage_reset;
hwif->set_pio_mode = &sil_set_pio_mode;
hwif->set_dma_mode = &sil_set_dma_mode;
......@@ -925,8 +902,6 @@ static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
if (!is_sata(hwif))
hwif->atapi_dma = 1;
hwif->ide_dma_check = &siimage_config_drive_for_dma;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_siimage(hwif);
......@@ -935,15 +910,6 @@ static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
} else {
hwif->ide_dma_test_irq = & siimage_io_ide_dma_test_irq;
}
/*
* The BIOS often doesn't set up DMA on this controller
* so we always do it.
*/
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
#define DECLARE_SII_DEV(name_str) \
......@@ -978,11 +944,11 @@ static int __devinit siimage_init_one(struct pci_dev *dev, const struct pci_devi
return ide_setup_pci_device(dev, &siimage_chipsets[id->driver_data]);
}
static struct pci_device_id siimage_pci_tbl[] = {
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id siimage_pci_tbl[] = {
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), 0 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_1210SA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_3112), 1 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 2 },
#endif
{ 0, },
};
......
drivers/ide/pci/sis5513.c
View file @ 2b0460b5
This diff is collapsed.
drivers/ide/pci/sl82c105.c
View file @ 2b0460b5
......@@ -144,19 +144,6 @@ static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed)
}
}
/*
* Check to see if the drive and chipset are capable of DMA mode.
*/
static int sl82c105_ide_dma_check(ide_drive_t *drive)
{
DBG(("sl82c105_ide_dma_check(drive:%s)\n", drive->name));
if (ide_tune_dma(drive))
return 0;
return -1;
}
/*
* The SL82C105 holds off all IDE interrupts while in DMA mode until
* all DMA activity is completed. Sometimes this causes problems (eg,
......@@ -404,17 +391,12 @@ static void __devinit init_hwif_sl82c105(ide_hwif_t *hwif)
hwif->atapi_dma = 1;
hwif->mwdma_mask = 0x07;
hwif->ide_dma_check = &sl82c105_ide_dma_check;
hwif->ide_dma_on = &sl82c105_ide_dma_on;
hwif->dma_off_quietly = &sl82c105_dma_off_quietly;
hwif->dma_lost_irq = &sl82c105_dma_lost_irq;
hwif->dma_start = &sl82c105_dma_start;
hwif->dma_timeout = &sl82c105_dma_timeout;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
if (hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
}
......@@ -434,8 +416,8 @@ static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_dev
return ide_setup_pci_device(dev, &sl82c105_chipset);
}
static struct pci_device_id sl82c105_pci_tbl[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0},
static const struct pci_device_id sl82c105_pci_tbl[] = {
{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);
......
drivers/ide/pci/slc90e66.c
View file @ 2b0460b5
/*
* linux/drivers/ide/pci/slc90e66.c Version 0.16 Jul 14, 2007
* linux/drivers/ide/pci/slc90e66.c Version 0.18 Aug 9, 2007
*
* Copyright (C) 2000-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
......@@ -21,27 +21,6 @@
#include <asm/io.h>
static u8 slc90e66_dma_2_pio (u8 xfer_rate) {
switch(xfer_rate) {
case XFER_UDMA_4:
case XFER_UDMA_3:
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
case XFER_MW_DMA_2:
return 4;
case XFER_MW_DMA_1:
return 3;
case XFER_SW_DMA_2:
return 2;
case XFER_MW_DMA_0:
case XFER_SW_DMA_1:
case XFER_SW_DMA_0:
default:
return 0;
}
}
static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
......@@ -132,26 +111,21 @@ static void slc90e66_set_dma_mode(ide_drive_t *drive, const u8 speed)
pci_write_config_word(dev, 0x4a, reg4a|u_speed);
}
} else {
const u8 mwdma_to_pio[] = { 0, 3, 4 };
u8 pio;
if (reg48 & u_flag)
pci_write_config_word(dev, 0x48, reg48 & ~u_flag);
if (reg4a & a_speed)
pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
}
slc90e66_set_pio_mode(drive, slc90e66_dma_2_pio(speed));
}
static int slc90e66_config_drive_xfer_rate (ide_drive_t *drive)
{
drive->init_speed = 0;
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
if (speed >= XFER_MW_DMA_0)
pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
else
pio = 2; /* only SWDMA2 is allowed */
return -1;
slc90e66_set_pio_mode(drive, pio);
}
}
static void __devinit init_hwif_slc90e66 (ide_hwif_t *hwif)
......@@ -159,8 +133,6 @@ static void __devinit init_hwif_slc90e66 (ide_hwif_t *hwif)
u8 reg47 = 0;
u8 mask = hwif->channel ? 0x01 : 0x02; /* bit0:Primary */
hwif->autodma = 0;
if (!hwif->irq)
hwif->irq = hwif->channel ? 15 : 14;
......@@ -169,11 +141,11 @@ static void __devinit init_hwif_slc90e66 (ide_hwif_t *hwif)
pci_read_config_byte(hwif->pci_dev, 0x47, &reg47);
if (!hwif->dma_base) {
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
if (hwif->dma_base == 0)
return;
}
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x1f;
......@@ -183,13 +155,6 @@ static void __devinit init_hwif_slc90e66 (ide_hwif_t *hwif)
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
/* bit[0(1)]: 0:80, 1:40 */
hwif->cbl = (reg47 & mask) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
hwif->ide_dma_check = &slc90e66_config_drive_xfer_rate;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t slc90e66_chipset __devinitdata = {
......@@ -206,8 +171,8 @@ static int __devinit slc90e66_init_one(struct pci_dev *dev, const struct pci_dev
return ide_setup_pci_device(dev, &slc90e66_chipset);
}
static struct pci_device_id slc90e66_pci_tbl[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_1), 0},
static const struct pci_device_id slc90e66_pci_tbl[] = {
{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_1), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, slc90e66_pci_tbl);
......
drivers/ide/pci/tc86c001.c
View file @ 2b0460b5
......@@ -162,17 +162,6 @@ static int tc86c001_busproc(ide_drive_t *drive, int state)
return 0;
}
static int tc86c001_config_drive_xfer_rate(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
ide_set_max_pio(drive);
return -1;
}
static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
{
unsigned long sc_base = pci_resource_start(hwif->pci_dev, 5);
......@@ -213,7 +202,6 @@ static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
hwif->ultra_mask = 0x1f;
hwif->mwdma_mask = 0x07;
hwif->ide_dma_check = &tc86c001_config_drive_xfer_rate;
hwif->dma_start = &tc86c001_dma_start;
if (hwif->cbl != ATA_CBL_PATA40_SHORT) {
......@@ -224,10 +212,6 @@ static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
scr1 = hwif->INW(sc_base + 0x00);
hwif->cbl = (scr1 & 0x2000) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static unsigned int __devinit init_chipset_tc86c001(struct pci_dev *dev,
......@@ -256,9 +240,8 @@ static int __devinit tc86c001_init_one(struct pci_dev *dev,
return ide_setup_pci_device(dev, &tc86c001_chipset);
}
static struct pci_device_id tc86c001_pci_tbl[] = {
{ PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id tc86c001_pci_tbl[] = {
{ PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE), 0 },
{ 0, }
};
MODULE_DEVICE_TABLE(pci, tc86c001_pci_tbl);
......
drivers/ide/pci/triflex.c
View file @ 2b0460b5
......@@ -96,16 +96,6 @@ static void triflex_set_pio_mode(ide_drive_t *drive, const u8 pio)
triflex_set_mode(drive, XFER_PIO_0 + pio);
}
static int triflex_config_drive_xfer_rate(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
ide_set_max_pio(drive);
return -1;
}
static void __devinit init_hwif_triflex(ide_hwif_t *hwif)
{
hwif->set_pio_mode = &triflex_set_pio_mode;
......@@ -117,12 +107,6 @@ static void __devinit init_hwif_triflex(ide_hwif_t *hwif)
hwif->atapi_dma = 1;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
hwif->ide_dma_check = &triflex_config_drive_xfer_rate;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t triflex_device __devinitdata = {
......@@ -140,9 +124,8 @@ static int __devinit triflex_init_one(struct pci_dev *dev,
return ide_setup_pci_device(dev, &triflex_device);
}
static struct pci_device_id triflex_pci_tbl[] = {
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
static const struct pci_device_id triflex_pci_tbl[] = {
{ PCI_VDEVICE(COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, triflex_pci_tbl);
......
drivers/ide/pci/trm290.c
View file @ 2b0460b5
......@@ -292,9 +292,6 @@ static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
hwif->ide_dma_test_irq = &trm290_ide_dma_test_irq;
hwif->selectproc = &trm290_selectproc;
hwif->autodma = 0; /* play it safe for now */
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
#if 1
{
/*
......@@ -329,6 +326,9 @@ static ide_pci_device_t trm290_chipset __devinitdata = {
.init_hwif = init_hwif_trm290,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
#if 0 /* play it safe for now */
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
#endif
};
static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id)
......@@ -336,8 +336,8 @@ static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_devic
return ide_setup_pci_device(dev, &trm290_chipset);
}
static struct pci_device_id trm290_pci_tbl[] = {
{ PCI_VENDOR_ID_TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id trm290_pci_tbl[] = {
{ PCI_VDEVICE(TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, trm290_pci_tbl);
......
drivers/ide/pci/via82cxxx.c
View file @ 2b0460b5
......@@ -197,24 +197,6 @@ static void via_set_pio_mode(ide_drive_t *drive, const u8 pio)
via_set_drive(drive, XFER_PIO_0 + pio);
}
/**
* via82cxxx_ide_dma_check - set up for DMA if possible
* @drive: IDE drive to set up
*
* Set up the drive for the highest supported speed considering the
* driver, controller and cable
*/
static int via82cxxx_ide_dma_check (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
ide_set_max_pio(drive);
return -1;
}
static struct via_isa_bridge *via_config_find(struct pci_dev **isa)
{
struct via_isa_bridge *via_config;
......@@ -443,8 +425,6 @@ static void __devinit init_hwif_via82cxxx(ide_hwif_t *hwif)
struct via82cxxx_dev *vdev = pci_get_drvdata(hwif->pci_dev);
int i;
hwif->autodma = 0;
hwif->set_pio_mode = &via_set_pio_mode;
hwif->set_dma_mode = &via_set_drive;
......@@ -458,7 +438,6 @@ static void __devinit init_hwif_via82cxxx(ide_hwif_t *hwif)
hwif->drives[i].io_32bit = 1;
hwif->drives[i].unmask = (vdev->via_config->flags & VIA_NO_UNMASK) ? 0 : 1;
hwif->drives[i].autotune = 1;
hwif->drives[i].dn = hwif->channel * 2 + i;
}
if (!hwif->dma_base)
......@@ -472,12 +451,6 @@ static void __devinit init_hwif_via82cxxx(ide_hwif_t *hwif)
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = via82cxxx_cable_detect(hwif);
hwif->ide_dma_check = &via82cxxx_ide_dma_check;
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t via82cxxx_chipsets[] __devinitdata = {
......@@ -522,11 +495,11 @@ static int __devinit via_init_one(struct pci_dev *dev, const struct pci_device_i
return ide_setup_pci_device(dev, &via82cxxx_chipsets[id->driver_data]);
}
static struct pci_device_id via_pci_tbl[] = {
{ PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_6410, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
{ PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_SATA_EIDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
static const struct pci_device_id via_pci_tbl[] = {
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C576_1), 0 },
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C586_1), 0 },
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_6410), 1 },
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_SATA_EIDE), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, via_pci_tbl);
......
drivers/ide/ppc/pmac.c
View file @ 2b0460b5
......@@ -1421,17 +1421,12 @@ static struct macio_driver pmac_ide_macio_driver =
.resume = pmac_ide_macio_resume,
};
static struct pci_device_id pmac_ide_pci_match[] = {
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_UNI_N_ATA,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_IPID_ATA100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_K2_ATA100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_SH_ATA,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
{ PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_IPID2_ATA,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
static const struct pci_device_id pmac_ide_pci_match[] = {
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_UNI_N_ATA), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID_ATA100), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_K2_ATA100), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_SH_ATA), 0 },
{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID2_ATA), 0 },
{},
};
......@@ -1578,19 +1573,6 @@ pmac_ide_destroy_dmatable (ide_drive_t *drive)
}
}
/*
* Check what is the best DMA timing setting for the drive and
* call appropriate functions to apply it.
*/
static int
pmac_ide_dma_check(ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
return -1;
}
/*
* Prepare a DMA transfer. We build the DMA table, adjust the timings for
* a read on KeyLargo ATA/66 and mark us as waiting for DMA completion
......@@ -1788,7 +1770,6 @@ pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
hwif->dma_off_quietly = &ide_dma_off_quietly;
hwif->ide_dma_on = &__ide_dma_on;
hwif->ide_dma_check = &pmac_ide_dma_check;
hwif->dma_setup = &pmac_ide_dma_setup;
hwif->dma_exec_cmd = &pmac_ide_dma_exec_cmd;
hwif->dma_start = &pmac_ide_dma_start;
......@@ -1823,9 +1804,6 @@ pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
hwif->swdma_mask = 0x00;
break;
}
hwif->autodma = 1;
hwif->drives[1].autodma = hwif->drives[0].autodma = hwif->autodma;
}
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
drivers/ide/setup-pci.c
View file @ 2b0460b5
......@@ -145,27 +145,13 @@ static int ide_setup_pci_baseregs (struct pci_dev *dev, const char *name)
}
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
#ifdef CONFIG_BLK_DEV_IDEDMA_FORCED
/*
* Long lost data from 2.0.34 that is now in 2.0.39
*
* This was used in ./drivers/block/triton.c to do DMA Base address setup
* when PnP failed. Oh the things we forget. I believe this was part
* of SFF-8038i that has been withdrawn from public access... :-((
*/
#define DEFAULT_BMIBA 0xe800 /* in case BIOS did not init it */
#define DEFAULT_BMCRBA 0xcc00 /* VIA's default value */
#define DEFAULT_BMALIBA 0xd400 /* ALI's default value */
#endif /* CONFIG_BLK_DEV_IDEDMA_FORCED */
/**
* ide_get_or_set_dma_base - setup BMIBA
* @hwif: Interface
*
* Fetch the DMA Bus-Master-I/O-Base-Address (BMIBA) from PCI space:
* If need be we set up the DMA base. Where a device has a partner that
* is already in DMA mode we check and enforce IDE simplex rules.
* Fetch the DMA Bus-Master-I/O-Base-Address (BMIBA) from PCI space.
* Where a device has a partner that is already in DMA mode we check
* and enforce IDE simplex rules.
*/
static unsigned long ide_get_or_set_dma_base (ide_hwif_t *hwif)
......@@ -173,12 +159,6 @@ static unsigned long ide_get_or_set_dma_base (ide_hwif_t *hwif)
unsigned long dma_base = 0;
struct pci_dev *dev = hwif->pci_dev;
#ifdef CONFIG_BLK_DEV_IDEDMA_FORCED
int second_chance = 0;
second_chance_to_dma:
#endif /* CONFIG_BLK_DEV_IDEDMA_FORCED */
if (hwif->mmio)
return hwif->dma_base;
......@@ -192,26 +172,6 @@ static unsigned long ide_get_or_set_dma_base (ide_hwif_t *hwif)
}
}
#ifdef CONFIG_BLK_DEV_IDEDMA_FORCED
/* FIXME - should use pci_assign_resource surely */
if ((!dma_base) && (!second_chance)) {
unsigned long set_bmiba = 0;
second_chance++;
switch(dev->vendor) {
case PCI_VENDOR_ID_AL:
set_bmiba = DEFAULT_BMALIBA; break;
case PCI_VENDOR_ID_VIA:
set_bmiba = DEFAULT_BMCRBA; break;
case PCI_VENDOR_ID_INTEL:
set_bmiba = DEFAULT_BMIBA; break;
default:
return dma_base;
}
pci_write_config_dword(dev, 0x20, set_bmiba|1);
goto second_chance_to_dma;
}
#endif /* CONFIG_BLK_DEV_IDEDMA_FORCED */
if (dma_base) {
u8 simplex_stat = 0;
dma_base += hwif->channel ? 8 : 0;
......@@ -478,8 +438,6 @@ static void ide_hwif_setup_dma(struct pci_dev *dev, ide_pci_device_t *d, ide_hwi
* Set up BM-DMA capability
* (PnP BIOS should have done this)
*/
/* default DMA off if we had to configure it here */
hwif->autodma = 0;
pci_set_master(dev);
if (pci_read_config_word(dev, PCI_COMMAND, &pcicmd) || !(pcicmd & PCI_COMMAND_MASTER)) {
printk(KERN_ERR "%s: %s error updating PCICMD\n",
......
include/linux/ide.h
View file @ 2b0460b5
......@@ -576,7 +576,6 @@ typedef struct ide_drive_s {
select_t select; /* basic drive/head select reg value */
u8 keep_settings; /* restore settings after drive reset */
u8 autodma; /* device can safely use dma on host */
u8 using_dma; /* disk is using dma for read/write */
u8 retry_pio; /* retrying dma capable host in pio */
u8 state; /* retry state */
......@@ -600,6 +599,7 @@ typedef struct ide_drive_s {
unsigned nice0 : 1; /* give obvious excess bandwidth */
unsigned nice2 : 1; /* give a share in our own bandwidth */
unsigned doorlocking : 1; /* for removable only: door lock/unlock works */
unsigned nodma : 1; /* disallow DMA */
unsigned autotune : 2; /* 0=default, 1=autotune, 2=noautotune */
unsigned remap_0_to_1 : 1; /* 0=noremap, 1=remap 0->1 (for EZDrive) */
unsigned blocked : 1; /* 1=powermanagment told us not to do anything, so sleep nicely */
......@@ -736,7 +736,6 @@ typedef struct hwif_s {
void (*dma_exec_cmd)(ide_drive_t *, u8);
void (*dma_start)(ide_drive_t *);
int (*ide_dma_end)(ide_drive_t *drive);
int (*ide_dma_check)(ide_drive_t *drive);
int (*ide_dma_on)(ide_drive_t *drive);
void (*dma_off_quietly)(ide_drive_t *drive);
int (*ide_dma_test_irq)(ide_drive_t *drive);
......@@ -798,7 +797,6 @@ typedef struct hwif_s {
unsigned serialized : 1; /* serialized all channel operation */
unsigned sharing_irq: 1; /* 1 = sharing irq with another hwif */
unsigned reset : 1; /* reset after probe */
unsigned autodma : 1; /* auto-attempt using DMA at boot */
unsigned no_lba48 : 1; /* 1 = cannot do LBA48 */
unsigned no_lba48_dma : 1; /* 1 = cannot do LBA48 DMA */
unsigned auto_poll : 1; /* supports nop auto-poll */
......@@ -1256,6 +1254,10 @@ enum {
IDE_HFLAG_POST_SET_MODE = (1 << 8),
/* don't program host/device for the transfer mode ("smart" hosts) */
IDE_HFLAG_NO_SET_MODE = (1 << 9),
/* trust BIOS for programming chipset/device for DMA */
IDE_HFLAG_TRUST_BIOS_FOR_DMA = (1 << 10),
/* host uses VDMA */
IDE_HFLAG_VDMA = (1 << 11),
};
typedef struct ide_pci_device_s {
......@@ -1303,7 +1305,6 @@ static inline u8 ide_max_dma_mode(ide_drive_t *drive)
return ide_find_dma_mode(drive, XFER_UDMA_6);
}
int ide_tune_dma(ide_drive_t *);
void ide_dma_off(ide_drive_t *);
void ide_dma_verbose(ide_drive_t *);
int ide_set_dma(ide_drive_t *);
......@@ -1330,7 +1331,6 @@ extern void ide_dma_timeout(ide_drive_t *);
#else
static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
static inline int ide_tune_dma(ide_drive_t *drive) { return 0; }
static inline void ide_dma_off(ide_drive_t *drive) { ; }
static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
......@@ -1380,7 +1380,6 @@ static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
extern char *ide_xfer_verbose(u8 xfer_rate);
extern void ide_toggle_bounce(ide_drive_t *drive, int on);
extern int ide_set_xfer_rate(ide_drive_t *drive, u8 rate);
int ide_use_fast_pio(ide_drive_t *);
static inline int ide_dev_has_iordy(struct hd_driveid *id)
{
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7