arm64: dts: mediatek: add ethernet support for mt8365-evk

- Enable "vibr" and "vsim2" regulators to power the ethernet chip.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v8-7-7019f3fd0adf@baylibre.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

arch/arm64/boot/dts/mediatek/mt8365-evk.dts

@@ -88,6 +88,29 @@ optee_reserved: optee@43200000 {
 	};
 };
 
+&ethernet {
+	pinctrl-0 = <&ethernet_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy>;
+	phy-mode = "rmii";
+	/*
+	 * Ethernet and HDMI (DSI0) are sharing pins.
+	 * Only one can be enabled at a time and require the physical switch
+	 * SW2101 to be set on LAN position
+	 * mt6357_vibr_reg and mt6357_vsim2_reg are needed to supply ethernet
+	 */
+	status = "disabled";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
 &i2c0 {
 	clock-frequency = <100000>;
 	pinctrl-0 = <&i2c0_pins>;
@@ -138,6 +161,31 @@ &mt6357_pmic {
 };
 
 &pio {
+	ethernet_pins: ethernet-pins {
+		phy_reset_pins {
+			pinmux = <MT8365_PIN_133_TDM_TX_DATA1__FUNC_GPIO133>;
+		};
+
+		rmii_pins {
+			pinmux = <MT8365_PIN_0_GPIO0__FUNC_EXT_TXD0>,
+				 <MT8365_PIN_1_GPIO1__FUNC_EXT_TXD1>,
+				 <MT8365_PIN_2_GPIO2__FUNC_EXT_TXD2>,
+				 <MT8365_PIN_3_GPIO3__FUNC_EXT_TXD3>,
+				 <MT8365_PIN_4_GPIO4__FUNC_EXT_TXC>,
+				 <MT8365_PIN_5_GPIO5__FUNC_EXT_RXER>,
+				 <MT8365_PIN_6_GPIO6__FUNC_EXT_RXC>,
+				 <MT8365_PIN_7_GPIO7__FUNC_EXT_RXDV>,
+				 <MT8365_PIN_8_GPIO8__FUNC_EXT_RXD0>,
+				 <MT8365_PIN_9_GPIO9__FUNC_EXT_RXD1>,
+				 <MT8365_PIN_10_GPIO10__FUNC_EXT_RXD2>,
+				 <MT8365_PIN_11_GPIO11__FUNC_EXT_RXD3>,
+				 <MT8365_PIN_12_GPIO12__FUNC_EXT_TXEN>,
+				 <MT8365_PIN_13_GPIO13__FUNC_EXT_COL>,
+				 <MT8365_PIN_14_GPIO14__FUNC_EXT_MDIO>,
+				 <MT8365_PIN_15_GPIO15__FUNC_EXT_MDC>;
+		};
+	};
+
 	gpio_keys: gpio-keys-pins {
 		pins {
 			pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;