clk: tegra: Enable hardware control of PLLE

Enable hardware control of PLLE spread-spectrum, IDDQ, and enable
controls when enabling PLLE.  The hardware (e.g. XUSB) using PLLE
will use these controls for power-saving optimizations.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

drivers/clk/tegra/clk-pll.c

@@ -96,10 +96,20 @@
 	(PLLE_SS_MAX_VAL | PLLE_SS_INC_VAL | PLLE_SS_INCINTRV_VAL)
 
 #define PLLE_AUX_PLLP_SEL	BIT(2)
+#define PLLE_AUX_USE_LOCKDET	BIT(3)
 #define PLLE_AUX_ENABLE_SWCTL	BIT(4)
+#define PLLE_AUX_SS_SWCTL	BIT(6)
 #define PLLE_AUX_SEQ_ENABLE	BIT(24)
+#define PLLE_AUX_SEQ_START_STATE BIT(25)
 #define PLLE_AUX_PLLRE_SEL	BIT(28)
 
+#define XUSBIO_PLL_CFG0		0x51c
+#define XUSBIO_PLL_CFG0_PADPLL_RESET_SWCTL	BIT(0)
+#define XUSBIO_PLL_CFG0_CLK_ENABLE_SWCTL	BIT(2)
+#define XUSBIO_PLL_CFG0_PADPLL_USE_LOCKDET	BIT(6)
+#define XUSBIO_PLL_CFG0_SEQ_ENABLE		BIT(24)
+#define XUSBIO_PLL_CFG0_SEQ_START_STATE		BIT(25)
+
 #define PLLE_MISC_PLLE_PTS	BIT(8)
 #define PLLE_MISC_IDDQ_SW_VALUE	BIT(13)
 #define PLLE_MISC_IDDQ_SW_CTRL	BIT(14)
@@ -1318,7 +1328,28 @@ static int clk_plle_tegra114_enable(struct clk_hw *hw)
 	pll_writel(val, PLLE_SS_CTRL, pll);
 	udelay(1);
 
-	/* TODO: enable hw control of xusb brick pll */
+	/* Enable hw control of xusb brick pll */
+	val = pll_readl_misc(pll);
+	val &= ~PLLE_MISC_IDDQ_SW_CTRL;
+	pll_writel_misc(val, pll);
+
+	val = pll_readl(pll->params->aux_reg, pll);
+	val |= (PLLE_AUX_USE_LOCKDET | PLLE_AUX_SEQ_START_STATE);
+	val &= ~(PLLE_AUX_ENABLE_SWCTL | PLLE_AUX_SS_SWCTL);
+	pll_writel(val, pll->params->aux_reg, pll);
+	udelay(1);
+	val |= PLLE_AUX_SEQ_ENABLE;
+	pll_writel(val, pll->params->aux_reg, pll);
+
+	val = pll_readl(XUSBIO_PLL_CFG0, pll);
+	val |= (XUSBIO_PLL_CFG0_PADPLL_USE_LOCKDET |
+		XUSBIO_PLL_CFG0_SEQ_START_STATE);
+	val &= ~(XUSBIO_PLL_CFG0_CLK_ENABLE_SWCTL |
+		 XUSBIO_PLL_CFG0_PADPLL_RESET_SWCTL);
+	pll_writel(val, XUSBIO_PLL_CFG0, pll);
+	udelay(1);
+	val |= XUSBIO_PLL_CFG0_SEQ_ENABLE;
+	pll_writel(val, XUSBIO_PLL_CFG0, pll);
 
 out:
 	if (pll->lock)