Merge branch 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc

* 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: S3C64XX: Configure backup battery charger on Cragganmore
  ARM: S3C64XX: Fix WM8915 IRQ polarity on Cragganmore
  ARM: S3C64XX: Configure supplies for all Cragganmore regulators
  ARM: S3C64XX: Refresh Cragganmore support
  ARM: S3C64XX: Initial support for Wolfson/Simtec Cragganmore/Banff
  OMAP4: Keyboard: Mux changes in the board file
  omap: blaze: add mmc5/wl1283 device support
  omap: 4430SDP: Register the card detect GPIO properly
  arm: omap3: cm-t35: add support for cm-t3730
  OMAP3: beagle: add support for beagleboard xM revision C
  OMAP3: rx-51: Add full regulator definitions
  omap: rx51: Platform support for lp5523 led chip

arch/arm/mach-omap2/Kconfig

@@ -266,9 +266,10 @@ config MACH_OMAP_ZOOM3
 	select REGULATOR_FIXED_VOLTAGE
 
 config MACH_CM_T35
-	bool "CompuLab CM-T35 module"
+	bool "CompuLab CM-T35/CM-T3730 modules"
 	depends on ARCH_OMAP3
 	default y
+	select MACH_CM_T3730
 	select OMAP_PACKAGE_CUS
 
 config MACH_CM_T3517
@@ -277,6 +278,9 @@ config MACH_CM_T3517
 	default y
 	select OMAP_PACKAGE_CBB
 
+config MACH_CM_T3730
+       bool
+
 config MACH_IGEP0020
 	bool "IGEP v2 board"
 	depends on ARCH_OMAP3

arch/arm/mach-omap2/board-4430sdp.c

@@ -22,6 +22,7 @@
 #include <linux/i2c/twl.h>
 #include <linux/gpio_keys.h>
 #include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
 #include <linux/leds.h>
 #include <linux/leds_pwm.h>
 
@@ -37,6 +38,7 @@
 #include <plat/mmc.h>
 #include <plat/omap4-keypad.h>
 #include <video/omapdss.h>
+#include <linux/wl12xx.h>
 
 #include "mux.h"
 #include "hsmmc.h"
@@ -51,6 +53,9 @@
 #define HDMI_GPIO_HPD 60 /* Hot plug pin for HDMI */
 #define HDMI_GPIO_LS_OE 41 /* Level shifter for HDMI */
 
+#define GPIO_WIFI_PMENA		54
+#define GPIO_WIFI_IRQ		53
+
 static const int sdp4430_keymap[] = {
 	KEY(0, 0, KEY_E),
 	KEY(0, 1, KEY_R),
@@ -124,6 +129,64 @@ static const int sdp4430_keymap[] = {
 	KEY(7, 6, KEY_OK),
 	KEY(7, 7, KEY_DOWN),
 };
+static struct omap_device_pad keypad_pads[] __initdata = {
+	{	.name   = "kpd_col1.kpd_col1",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "kpd_col1.kpd_col1",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "kpd_col2.kpd_col2",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "kpd_col3.kpd_col3",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "kpd_col4.kpd_col4",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "kpd_col5.kpd_col5",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "gpmc_a23.kpd_col7",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "gpmc_a22.kpd_col6",
+		.enable = OMAP_WAKEUP_EN | OMAP_MUX_MODE1,
+	},
+	{	.name   = "kpd_row0.kpd_row0",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+	{	.name   = "kpd_row1.kpd_row1",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+	{	.name   = "kpd_row2.kpd_row2",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+	{	.name   = "kpd_row3.kpd_row3",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+	{	.name   = "kpd_row4.kpd_row4",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+	{	.name   = "kpd_row5.kpd_row5",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+	{	.name   = "gpmc_a18.kpd_row6",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+	{	.name   = "gpmc_a19.kpd_row7",
+		.enable = OMAP_PULL_ENA | OMAP_PULL_UP | OMAP_WAKEUP_EN |
+			OMAP_MUX_MODE1 | OMAP_INPUT_EN,
+	},
+};
 
 static struct matrix_keymap_data sdp4430_keymap_data = {
 	.keymap			= sdp4430_keymap,
@@ -135,6 +198,13 @@ static struct omap4_keypad_platform_data sdp4430_keypad_data = {
 	.rows			= 8,
 	.cols			= 8,
 };
+
+static struct omap_board_data keypad_data = {
+	.id	    		= 1,
+	.pads	 		= keypad_pads,
+	.pads_cnt       	= ARRAY_SIZE(keypad_pads),
+};
+
 static struct gpio_led sdp4430_gpio_leds[] = {
 	{
 		.name	= "omap4:green:debug0",
@@ -315,8 +385,17 @@ static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
 		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
+	{
+		.mmc		= 5,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+		.ocr_mask	= MMC_VDD_165_195,
+		.nonremovable	= true,
+	},
 	{}	/* Terminator */
 };
 
@@ -324,6 +403,37 @@ static struct regulator_consumer_supply sdp4430_vaux_supply[] = {
 	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
 };
 
+static struct regulator_consumer_supply omap4_sdp4430_vmmc5_supply = {
+	.supply = "vmmc",
+	.dev_name = "omap_hsmmc.4",
+};
+
+static struct regulator_init_data sdp4430_vmmc5 = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies = 1,
+	.consumer_supplies = &omap4_sdp4430_vmmc5_supply,
+};
+
+static struct fixed_voltage_config sdp4430_vwlan = {
+	.supply_name		= "vwl1271",
+	.microvolts		= 1800000, /* 1.8V */
+	.gpio			= GPIO_WIFI_PMENA,
+	.startup_delay		= 70000, /* 70msec */
+	.enable_high		= 1,
+	.enabled_at_boot	= 0,
+	.init_data		= &sdp4430_vmmc5,
+};
+
+static struct platform_device omap_vwlan_device = {
+	.name		= "reg-fixed-voltage",
+	.id		= 1,
+	.dev = {
+		.platform_data = &sdp4430_vwlan,
+	},
+};
+
 static int omap4_twl6030_hsmmc_late_init(struct device *dev)
 {
 	int ret = 0;
@@ -593,6 +703,41 @@ static inline void board_serial_init(void)
 }
  #endif
 
+static void omap4_sdp4430_wifi_mux_init(void)
+{
+	omap_mux_init_gpio(GPIO_WIFI_IRQ, OMAP_PIN_INPUT |
+				OMAP_PIN_OFF_WAKEUPENABLE);
+	omap_mux_init_gpio(GPIO_WIFI_PMENA, OMAP_PIN_OUTPUT);
+
+	omap_mux_init_signal("sdmmc5_cmd.sdmmc5_cmd",
+				OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_signal("sdmmc5_clk.sdmmc5_clk",
+				OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_signal("sdmmc5_dat0.sdmmc5_dat0",
+				OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_signal("sdmmc5_dat1.sdmmc5_dat1",
+				OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_signal("sdmmc5_dat2.sdmmc5_dat2",
+				OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP);
+	omap_mux_init_signal("sdmmc5_dat3.sdmmc5_dat3",
+				OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP);
+
+}
+
+static struct wl12xx_platform_data omap4_sdp4430_wlan_data __initdata = {
+	.irq = OMAP_GPIO_IRQ(GPIO_WIFI_IRQ),
+	.board_ref_clock = WL12XX_REFCLOCK_26,
+	.board_tcxo_clock = WL12XX_TCXOCLOCK_26,
+};
+
+static void omap4_sdp4430_wifi_init(void)
+{
+	omap4_sdp4430_wifi_mux_init();
+	if (wl12xx_set_platform_data(&omap4_sdp4430_wlan_data))
+		pr_err("Error setting wl12xx data\n");
+	platform_device_register(&omap_vwlan_device);
+}
+
 static void __init omap_4430sdp_init(void)
 {
 	int status;
@@ -609,6 +754,7 @@ static void __init omap_4430sdp_init(void)
 	omap_sfh7741prox_init();
 	platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices));
 	board_serial_init();
+	omap4_sdp4430_wifi_init();
 	omap4_twl6030_hsmmc_init(mmc);
 
 	usb_musb_init(&musb_board_data);
@@ -622,7 +768,7 @@ static void __init omap_4430sdp_init(void)
 				ARRAY_SIZE(sdp4430_spi_board_info));
 	}
 
-	status = omap4_keyboard_init(&sdp4430_keypad_data);
+	status = omap4_keyboard_init(&sdp4430_keypad_data, &keypad_data);
 	if (status)
 		pr_err("Keypad initialization failed: %d\n", status);
 

arch/arm/mach-omap2/board-cm-t35.c

 /*
- * board-cm-t35.c (CompuLab CM-T35 module)
+ * CompuLab CM-T35/CM-T3730 modules support
  *
  * Copyright (C) 2009-2011 CompuLab, Ltd.
  * Authors: Mike Rapoport <mike@compulab.co.il>
@@ -535,17 +535,11 @@ static struct omap_board_mux board_mux[] __initdata = {
 	OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
 
-	/* DSS */
+	/* common DSS */
 	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
@@ -558,12 +552,6 @@ static struct omap_board_mux board_mux[] __initdata = {
 	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 
 	/* display controls */
 	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
@@ -576,19 +564,53 @@ static struct omap_board_mux board_mux[] __initdata = {
 
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
+
+static void __init cm_t3x_common_dss_mux_init(int mux_mode)
+{
+	omap_mux_init_signal("dss_data18", mux_mode);
+	omap_mux_init_signal("dss_data19", mux_mode);
+	omap_mux_init_signal("dss_data20", mux_mode);
+	omap_mux_init_signal("dss_data21", mux_mode);
+	omap_mux_init_signal("dss_data22", mux_mode);
+	omap_mux_init_signal("dss_data23", mux_mode);
+}
+
+static void __init cm_t35_init_mux(void)
+{
+	omap_mux_init_signal("gpio_70", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_71", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_72", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_73", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_74", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_75", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+}
+
+static void __init cm_t3730_init_mux(void)
+{
+	omap_mux_init_signal("sys_boot0", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot1", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot3", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot4", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot5", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot6", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+}
+#else
+static inline void cm_t35_init_mux(void) {}
+static inline void cm_t3730_init_mux(void) {}
 #endif
 
 static struct omap_board_config_kernel cm_t35_config[] __initdata = {
 };
 
-static void __init cm_t35_init(void)
+static void __init cm_t3x_common_init(void)
 {
 	omap_board_config = cm_t35_config;
 	omap_board_config_size = ARRAY_SIZE(cm_t35_config);
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
 	omap_serial_init();
 	cm_t35_init_i2c();
-	cm_t35_init_nand();
 	omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
 	cm_t35_init_ethernet();
 	cm_t35_init_led();
@@ -598,6 +620,19 @@ static void __init cm_t35_init(void)
 	usbhs_init(&usbhs_bdata);
 }
 
+static void __init cm_t35_init(void)
+{
+	cm_t3x_common_init();
+	cm_t35_init_mux();
+	cm_t35_init_nand();
+}
+
+static void __init cm_t3730_init(void)
+{
+	cm_t3x_common_init();
+	cm_t3730_init_mux();
+}
+
 MACHINE_START(CM_T35, "Compulab CM-T35")
 	.boot_params	= 0x80000100,
 	.reserve	= omap_reserve,
@@ -607,3 +642,13 @@ MACHINE_START(CM_T35, "Compulab CM-T35")
 	.init_machine	= cm_t35_init,
 	.timer		= &omap3_timer,
 MACHINE_END
+
+MACHINE_START(CM_T3730, "Compulab CM-T3730")
+	.boot_params    = 0x80000100,
+	.reserve        = omap_reserve,
+	.map_io         = omap3_map_io,
+	.init_early     = cm_t35_init_early,
+	.init_irq       = omap3_init_irq,
+	.init_machine   = cm_t3730_init,
+	.timer          = &omap3_timer,
+MACHINE_END

arch/arm/mach-omap2/board-omap3beagle.c

@@ -60,7 +60,8 @@
  *	AXBX	= GPIO173, GPIO172, GPIO171: 1 1 1
  *	C1_3	= GPIO173, GPIO172, GPIO171: 1 1 0
  *	C4	= GPIO173, GPIO172, GPIO171: 1 0 1
- *	XM	= GPIO173, GPIO172, GPIO171: 0 0 0
+ *	XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
+ *	XMC = GPIO173, GPIO172, GPIO171: 0 1 0
  */
 enum {
 	OMAP3BEAGLE_BOARD_UNKN = 0,
@@ -68,14 +69,26 @@ enum {
 	OMAP3BEAGLE_BOARD_C1_3,
 	OMAP3BEAGLE_BOARD_C4,
 	OMAP3BEAGLE_BOARD_XM,
+	OMAP3BEAGLE_BOARD_XMC,
 };
 
 static u8 omap3_beagle_version;
 
-static u8 omap3_beagle_get_rev(void)
-{
-	return omap3_beagle_version;
-}
+/*
+ * Board-specific configuration
+ * Defaults to BeagleBoard-xMC
+ */
+static struct {
+	int mmc1_gpio_wp;
+	int usb_pwr_level;
+	int reset_gpio;
+	int usr_button_gpio;
+} beagle_config = {
+	.mmc1_gpio_wp = -EINVAL,
+	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
+	.reset_gpio = 129,
+	.usr_button_gpio = 4,
+};
 
 static struct gpio omap3_beagle_rev_gpios[] __initdata = {
 	{ 171, GPIOF_IN, "rev_id_0"    },
@@ -110,18 +123,32 @@ static void __init omap3_beagle_init_rev(void)
 	case 7:
 		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
+		beagle_config.mmc1_gpio_wp = 29;
+		beagle_config.reset_gpio = 170;
+		beagle_config.usr_button_gpio = 7;
 		break;
 	case 6:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
+		beagle_config.mmc1_gpio_wp = 23;
+		beagle_config.reset_gpio = 170;
+		beagle_config.usr_button_gpio = 7;
 		break;
 	case 5:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
+		beagle_config.mmc1_gpio_wp = 23;
+		beagle_config.reset_gpio = 170;
+		beagle_config.usr_button_gpio = 7;
 		break;
 	case 0:
-		printk(KERN_INFO "OMAP3 Beagle Rev: xM\n");
+		printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
+		beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
+		break;
+	case 2:
+		printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
+		omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
 		break;
 	default:
 		printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
@@ -225,7 +252,7 @@ static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
 		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-		.gpio_wp	= 29,
+		.gpio_wp	= -EINVAL,
 	},
 	{}	/* Terminator */
 };
@@ -243,17 +270,11 @@ static struct gpio_led gpio_leds[];
 static int beagle_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
-	int r, usb_pwr_level;
-
-	if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
-		mmc[0].gpio_wp = -EINVAL;
-	} else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
-		(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
-		omap_mux_init_gpio(23, OMAP_PIN_INPUT);
-		mmc[0].gpio_wp = 23;
-	} else {
-		omap_mux_init_gpio(29, OMAP_PIN_INPUT);
-	}
+	int r;
+
+	if (beagle_config.mmc1_gpio_wp != -EINVAL)
+		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
+	mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
 	omap2_hsmmc_init(mmc);
@@ -263,9 +284,8 @@ static int beagle_twl_gpio_setup(struct device *dev,
 	 * high / others active low)
 	 * DVI reset GPIO is different between beagle revisions
 	 */
-	if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
-		usb_pwr_level = GPIOF_OUT_INIT_HIGH;
-		beagle_dvi_device.reset_gpio = 129;
+	/* Valid for all -xM revisions */
+	if (cpu_is_omap3630()) {
 		/*
 		 * gpio + 1 on Xm controls the TFP410's enable line (active low)
 		 * gpio + 2 control varies depending on the board rev as below:
@@ -283,8 +303,6 @@ static int beagle_twl_gpio_setup(struct device *dev,
 			pr_err("%s: unable to configure DVI_LDO_EN\n",
 				__func__);
 	} else {
-		usb_pwr_level = GPIOF_OUT_INIT_LOW;
-		beagle_dvi_device.reset_gpio = 170;
 		/*
 		 * REVISIT: need ehci-omap hooks for external VBUS
 		 * power switch and overcurrent detect
@@ -292,8 +310,10 @@ static int beagle_twl_gpio_setup(struct device *dev,
 		if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
 			pr_err("%s: unable to configure EHCI_nOC\n", __func__);
 	}
+	beagle_dvi_device.reset_gpio = beagle_config.reset_gpio;
 
-	gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR");
+	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
+			"nEN_USB_PWR");
 
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -404,7 +424,8 @@ static struct platform_device leds_gpio = {
 static struct gpio_keys_button gpio_buttons[] = {
 	{
 		.code			= BTN_EXTRA,
-		.gpio			= 7,
+		/* Dynamically assigned depending on board */
+		.gpio			= -EINVAL,
 		.desc			= "user",
 		.wakeup			= 1,
 	},
@@ -468,8 +489,8 @@ static void __init beagle_opp_init(void)
 		return;
 	}
 
-	/* Custom OPP enabled for XM */
-	if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
+	/* Custom OPP enabled for all xM versions */
+	if (cpu_is_omap3630()) {
 		struct omap_hwmod *mh = omap_hwmod_lookup("mpu");
 		struct omap_hwmod *dh = omap_hwmod_lookup("iva");
 		struct device *dev;
@@ -509,6 +530,9 @@ static void __init omap3_beagle_init(void)
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap3_beagle_init_rev();
 	omap3_beagle_i2c_init();
+
+	gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
+
 	platform_add_devices(omap3_beagle_devices,
 			ARRAY_SIZE(omap3_beagle_devices));
 	omap_display_init(&beagle_dss_data);

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -39,6 +39,7 @@
 #include <sound/tpa6130a2-plat.h>
 #include <media/radio-si4713.h>
 #include <media/si4713.h>
+#include <linux/leds-lp5523.h>
 
 #include <../drivers/staging/iio/light/tsl2563.h>
 
@@ -53,6 +54,7 @@
 #define RX51_WL1251_IRQ_GPIO		42
 #define RX51_FMTX_RESET_GPIO		163
 #define RX51_FMTX_IRQ			53
+#define RX51_LP5523_CHIP_EN_GPIO	41
 
 #define RX51_USB_TRANSCEIVER_RST_GPIO	67
 
@@ -71,6 +73,64 @@ static struct tsl2563_platform_data rx51_tsl2563_platform_data = {
 };
 #endif
 
+#if defined(CONFIG_LEDS_LP5523) || defined(CONFIG_LEDS_LP5523_MODULE)
+static struct lp5523_led_config rx51_lp5523_led_config[] = {
+	{
+		.chan_nr	= 0,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 1,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 2,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 3,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 4,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 5,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 6,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 7,
+		.led_current	= 50,
+	}, {
+		.chan_nr	= 8,
+		.led_current	= 50,
+	}
+};
+
+static int rx51_lp5523_setup(void)
+{
+	return gpio_request_one(RX51_LP5523_CHIP_EN_GPIO, GPIOF_DIR_OUT,
+			"lp5523_enable");
+}
+
+static void rx51_lp5523_release(void)
+{
+	gpio_free(RX51_LP5523_CHIP_EN_GPIO);
+}
+
+static void rx51_lp5523_enable(bool state)
+{
+	gpio_set_value(RX51_LP5523_CHIP_EN_GPIO, !!state);
+}
+
+static struct lp5523_platform_data rx51_lp5523_platform_data = {
+	.led_config		= rx51_lp5523_led_config,
+	.num_channels		= ARRAY_SIZE(rx51_lp5523_led_config),
+	.clock_mode		= LP5523_CLOCK_AUTO,
+	.setup_resources	= rx51_lp5523_setup,
+	.release_resources	= rx51_lp5523_release,
+	.enable			= rx51_lp5523_enable,
+};
+#endif
+
 static struct omap2_mcspi_device_config wl1251_mcspi_config = {
 	.turbo_mode	= 0,
 	.single_channel	= 1,
@@ -495,6 +555,32 @@ static struct regulator_init_data rx51_vmmc2 = {
 	.consumer_supplies	= rx51_vmmc2_supplies,
 };
 
+static struct regulator_init_data rx51_vpll1 = {
+	.constraints = {
+		.name			= "VPLL",
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.always_on		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE,
+	},
+};
+
+static struct regulator_init_data rx51_vpll2 = {
+	.constraints = {
+		.name			= "VSDI_CSI",
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.always_on		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE,
+	},
+};
+
 static struct regulator_init_data rx51_vsim = {
 	.constraints = {
 		.name			= "VMMC2_IO_18",
@@ -524,6 +610,43 @@ static struct regulator_init_data rx51_vio = {
 	.consumer_supplies	= rx51_vio_supplies,
 };
 
+static struct regulator_init_data rx51_vintana1 = {
+	.constraints = {
+		.name			= "VINTANA1",
+		.min_uV			= 1500000,
+		.max_uV			= 1500000,
+		.always_on		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE,
+	},
+};
+
+static struct regulator_init_data rx51_vintana2 = {
+	.constraints = {
+		.name			= "VINTANA2",
+		.min_uV			= 2750000,
+		.max_uV			= 2750000,
+		.apply_uV		= true,
+		.always_on		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE,
+	},
+};
+
+static struct regulator_init_data rx51_vintdig = {
+	.constraints = {
+		.name			= "VINTDIG",
+		.min_uV			= 1500000,
+		.max_uV			= 1500000,
+		.always_on		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE,
+	},
+};
+
 static struct si4713_platform_data rx51_si4713_i2c_data __initdata_or_module = {
 	.gpio_reset	= RX51_FMTX_RESET_GPIO,
 };
@@ -761,7 +884,12 @@ static struct twl4030_platform_data rx51_twldata __initdata = {
 	.vaux2			= &rx51_vaux2,
 	.vaux4			= &rx51_vaux4,
 	.vmmc1			= &rx51_vmmc1,
+	.vpll1			= &rx51_vpll1,
+	.vpll2			= &rx51_vpll2,
 	.vsim			= &rx51_vsim,
+	.vintana1		= &rx51_vintana1,
+	.vintana2		= &rx51_vintana2,
+	.vintdig		= &rx51_vintdig,
 	.vio			= &rx51_vio,
 };
 
@@ -799,6 +927,12 @@ static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_2[] = {
 		I2C_BOARD_INFO("tsl2563", 0x29),
 		.platform_data = &rx51_tsl2563_platform_data,
 	},
+#endif
+#if defined(CONFIG_LEDS_LP5523) || defined(CONFIG_LEDS_LP5523_MODULE)
+	{
+		I2C_BOARD_INFO("lp5523", 0x32),
+		.platform_data  = &rx51_lp5523_platform_data,
+	},
 #endif
 	{
 		I2C_BOARD_INFO("tpa6130a2", 0x60),
@@ -950,6 +1084,7 @@ static void __init rx51_init_wl1251(void)
 void __init rx51_peripherals_init(void)
 {
 	rx51_i2c_init();
+	regulator_has_full_constraints();
 	gpmc_onenand_init(board_onenand_data);
 	board_smc91x_init();
 	rx51_add_gpio_keys();

arch/arm/mach-omap2/devices.c

@@ -230,7 +230,7 @@ struct omap_device_pm_latency omap_keyboard_latency[] = {
 };
 
 int __init omap4_keyboard_init(struct omap4_keypad_platform_data
-						*sdp4430_keypad_data)
+			*sdp4430_keypad_data, struct omap_board_data *bdata)
 {
 	struct omap_device *od;
 	struct omap_hwmod *oh;
@@ -257,6 +257,7 @@ int __init omap4_keyboard_init(struct omap4_keypad_platform_data
 						name, oh->name);
 		return PTR_ERR(od);
 	}
+	oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
 
 	return 0;
 }

arch/arm/mach-s3c64xx/Kconfig

@@ -267,3 +267,26 @@ config MACH_SMARTQ7
 	select MACH_SMARTQ
 	help
 	    Machine support for the SmartQ 7
+
+config MACH_WLF_CRAGG_6410
+	bool "Wolfson Cragganmore 6410"
+	select CPU_S3C6410
+	select S3C64XX_SETUP_SDHCI
+	select S3C64XX_SETUP_I2C1
+	select S3C64XX_SETUP_IDE
+	select S3C64XX_SETUP_FB_24BPP
+	select S3C64XX_SETUP_KEYPAD
+	select SAMSUNG_DEV_ADC
+	select SAMSUNG_DEV_KEYPAD
+	select S3C_DEV_USB_HOST
+	select S3C_DEV_USB_HSOTG
+	select S3C_DEV_HSMMC
+	select S3C_DEV_HSMMC1
+	select S3C_DEV_HSMMC2
+	select S3C_DEV_I2C1
+	select S3C_DEV_WDT
+	select S3C_DEV_RTC
+	select S3C64XX_DEV_SPI
+	select S3C24XX_GPIO_EXTRA128
+	help
+	  Machine support for the Wolfson Cragganmore S3C6410 variant.

arch/arm/mach-s3c64xx/Makefile

@@ -55,6 +55,7 @@ obj-$(CONFIG_MACH_HMT)		+= mach-hmt.o
 obj-$(CONFIG_MACH_SMARTQ)	+= mach-smartq.o
 obj-$(CONFIG_MACH_SMARTQ5)	+= mach-smartq5.o
 obj-$(CONFIG_MACH_SMARTQ7)	+= mach-smartq7.o
+obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o
 
 # device support
 

arch/arm/mach-s3c64xx/include/mach/irqs.h

@@ -198,7 +198,9 @@
  * interrupt controllers). */
 #define IRQ_BOARD_START (IRQ_EINT_GROUP9_BASE + IRQ_EINT_GROUP9_NR + 1)
 
-#ifdef CONFIG_SMDK6410_WM1190_EV1
+#ifdef CONFIG_MACH_WLF_CRAGG_6410
+#define IRQ_BOARD_NR 128
+#elif defined(CONFIG_SMDK6410_WM1190_EV1)
 #define IRQ_BOARD_NR 64
 #elif defined(CONFIG_SMDK6410_WM1192_EV1)
 #define IRQ_BOARD_NR 64

arch/arm/plat-omap/include/plat/omap4-keypad.h

@@ -10,5 +10,6 @@ struct omap4_keypad_platform_data {
 	u8 cols;
 };
 
-extern int omap4_keyboard_init(struct omap4_keypad_platform_data *);
+extern int omap4_keyboard_init(struct omap4_keypad_platform_data *,
+				struct omap_board_data *);
 #endif

arch/arm/plat-omap/include/plat/uncompress.h

@@ -148,6 +148,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap3 based boards using UART3 */
 		DEBUG_LL_OMAP3(3, cm_t35);
 		DEBUG_LL_OMAP3(3, cm_t3517);
+		DEBUG_LL_OMAP3(3, cm_t3730);
 		DEBUG_LL_OMAP3(3, craneboard);
 		DEBUG_LL_OMAP3(3, devkit8000);
 		DEBUG_LL_OMAP3(3, igep0020);