Commit 3834507d authored by Stephen Hemminger's avatar Stephen Hemminger Committed by David S. Miller

sky2: set VPD size

Read configuration register during probe and use it to size the
available VPD. Move existing code using same register slightly
earlier in probe handling.
Signed-off-by: default avatarStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent e4c2abe2
...@@ -4356,6 +4356,7 @@ static int __devinit sky2_probe(struct pci_dev *pdev, ...@@ -4356,6 +4356,7 @@ static int __devinit sky2_probe(struct pci_dev *pdev,
struct net_device *dev; struct net_device *dev;
struct sky2_hw *hw; struct sky2_hw *hw;
int err, using_dac = 0, wol_default; int err, using_dac = 0, wol_default;
u32 reg;
char buf1[16]; char buf1[16];
err = pci_enable_device(pdev); err = pci_enable_device(pdev);
...@@ -4389,6 +4390,34 @@ static int __devinit sky2_probe(struct pci_dev *pdev, ...@@ -4389,6 +4390,34 @@ static int __devinit sky2_probe(struct pci_dev *pdev,
} }
} }
/* Get configuration information
* Note: only regular PCI config access once to test for HW issues
* other PCI access through shared memory for speed and to
* avoid MMCONFIG problems.
*/
err = pci_read_config_dword(pdev, PCI_DEV_REG2, &reg);
if (err) {
dev_err(&pdev->dev, "PCI read config failed\n");
goto err_out_free_regions;
}
/* size of available VPD, only impact sysfs */
err = pci_vpd_truncate(pdev, 1ul << (((reg & PCI_VPD_ROM_SZ) >> 14) + 8));
if (err)
dev_warn(&pdev->dev, "Can't set VPD size\n");
#ifdef __BIG_ENDIAN
/* The sk98lin vendor driver uses hardware byte swapping but
* this driver uses software swapping.
*/
reg &= ~PCI_REV_DESC;
err = pci_write_config_dword(pdev,PCI_DEV_REG2, reg);
if (err) {
dev_err(&pdev->dev, "PCI write config failed\n");
goto err_out_free_regions;
}
#endif
wol_default = device_may_wakeup(&pdev->dev) ? WAKE_MAGIC : 0; wol_default = device_may_wakeup(&pdev->dev) ? WAKE_MAGIC : 0;
err = -ENOMEM; err = -ENOMEM;
...@@ -4406,18 +4435,6 @@ static int __devinit sky2_probe(struct pci_dev *pdev, ...@@ -4406,18 +4435,6 @@ static int __devinit sky2_probe(struct pci_dev *pdev,
goto err_out_free_hw; goto err_out_free_hw;
} }
#ifdef __BIG_ENDIAN
/* The sk98lin vendor driver uses hardware byte swapping but
* this driver uses software swapping.
*/
{
u32 reg;
reg = sky2_pci_read32(hw, PCI_DEV_REG2);
reg &= ~PCI_REV_DESC;
sky2_pci_write32(hw, PCI_DEV_REG2, reg);
}
#endif
/* ring for status responses */ /* ring for status responses */
hw->st_le = pci_alloc_consistent(pdev, STATUS_LE_BYTES, &hw->st_dma); hw->st_le = pci_alloc_consistent(pdev, STATUS_LE_BYTES, &hw->st_dma);
if (!hw->st_le) if (!hw->st_le)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment