Commit 3a736bcb authored by Emmanuel Grumbach's avatar Emmanuel Grumbach

iwlwifi: trans: don't configure the set_active in SCD for dvm

This configuration is not needed for dvm, and it actually
broke it.
Reported-by: default avatarOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: default avatarEmmanuel Grumbach <emmanuel.grumbach@intel.com>
parent f7f89e7b
......@@ -377,6 +377,7 @@ enum iwl_trans_status {
* if unset 4k will be the RX buffer size
* @bc_table_dword: set to true if the BC table expects the byte count to be
* in DWORD (as opposed to bytes)
* @scd_set_active: should the transport configure the SCD for HCMD queue
* @queue_watchdog_timeout: time (in ms) after which queues
* are considered stuck and will trigger device restart
* @command_names: array of command names, must be 256 entries
......@@ -392,6 +393,7 @@ struct iwl_trans_config {
bool rx_buf_size_8k;
bool bc_table_dword;
bool scd_set_active;
unsigned int queue_watchdog_timeout;
const char *const *command_names;
};
......
......@@ -460,6 +460,7 @@ iwl_op_mode_mvm_start(struct iwl_trans *trans, const struct iwl_cfg *cfg,
trans_cfg.cmd_queue = IWL_MVM_CMD_QUEUE;
trans_cfg.cmd_fifo = IWL_MVM_TX_FIFO_CMD;
trans_cfg.scd_set_active = true;
snprintf(mvm->hw->wiphy->fw_version,
sizeof(mvm->hw->wiphy->fw_version),
......
......@@ -257,6 +257,7 @@ iwl_pcie_get_scratchbuf_dma(struct iwl_txq *txq, int idx)
* @cmd_queue - command queue number
* @rx_buf_size_8k: 8 kB RX buffer size
* @bc_table_dword: true if the BC table expects DWORD (as opposed to bytes)
* @scd_set_active: should the transport configure the SCD for HCMD queue
* @rx_page_order: page order for receive buffer size
* @wd_timeout: queue watchdog timeout (jiffies)
* @reg_lock: protect hw register access
......@@ -306,6 +307,7 @@ struct iwl_trans_pcie {
bool rx_buf_size_8k;
bool bc_table_dword;
bool scd_set_active;
u32 rx_page_order;
const char *const *command_names;
......
......@@ -1171,6 +1171,7 @@ static void iwl_trans_pcie_configure(struct iwl_trans *trans,
trans_pcie->command_names = trans_cfg->command_names;
trans_pcie->bc_table_dword = trans_cfg->bc_table_dword;
trans_pcie->scd_set_active = trans_cfg->scd_set_active;
/* Initialize NAPI here - it should be before registering to mac80211
* in the opmode but after the HW struct is allocated.
......
......@@ -1080,7 +1080,8 @@ void iwl_trans_pcie_txq_enable(struct iwl_trans *trans, int txq_id, u16 ssn,
fifo = cfg->fifo;
/* Disable the scheduler prior configuring the cmd queue */
if (txq_id == trans_pcie->cmd_queue)
if (txq_id == trans_pcie->cmd_queue &&
trans_pcie->scd_set_active)
iwl_scd_enable_set_active(trans, 0);
/* Stop this Tx queue before configuring it */
......@@ -1142,7 +1143,8 @@ void iwl_trans_pcie_txq_enable(struct iwl_trans *trans, int txq_id, u16 ssn,
SCD_QUEUE_STTS_REG_MSK);
/* enable the scheduler for this queue (only) */
if (txq_id == trans_pcie->cmd_queue)
if (txq_id == trans_pcie->cmd_queue &&
trans_pcie->scd_set_active)
iwl_scd_enable_set_active(trans, BIT(txq_id));
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment